Search Documents

By Anthony A. Zoobkoff

Gotcha! ? What Did I Just Agree To? ? You can?t repeat or use anything you heard. ? Did you agree before you knew what you were going to be given, told or shown? ? If you knew what you were to be given, told or shown, would you have still agreed?

May 1, 2013

By L. H. McKay

Tailing Dams Three types of dam have been structed to impound tailings from the Allenby mill: 1.- By classifier unit 2.- By earth dam 3.- By direct deposition of tailings The first type, which includes two dams, was built across a shallow valley which sloped down to Similkameen river, just below the mill site. Two earth embankments, one below the other, were built across the valley. Tailings were then piped to Akins classifiers mounted on wooden wheels. The classifiers were set up at one side of the valley and gradually moved ahead on the sand embankment created by the sand discharge from these classifiers, the slime overflow going to settli.ng ponds formed by the dams. Decanting wells were built in the settling ponds by placing four six-by-six timbers vertically in the ground, two feet apart, to which two-by-six tongue-and-groove boards were nailed. The elevations of the ponds were raised, as required, by nailing additional two-by-six boards on the well and bolting on more six-by-six timbers when required. The bottoms of the wells were attached to a covered launder made of three-inch lumber laid on a one per cent grade. This launder carried the overflow through the dam. The second type of dam was built across a long, narrow valley, known as Hitchen's Flat, the upper ~n d of which was about 2½ miles north of the mill. This valley, an ideal tailings site, was 4,000 feet long and from 600 to 800 feet wide. An earth embankment with a concrete spillway through the top was built approximately 28 feet high across the lower end of this valley. Tailings were then dumped into the upper end of valley, with no further expense until the basin was filled up to the level of the flume where this entered the valley. When the upper end of the valley was filled to this point there was still room for more tailings at the lower end. Therefore, a pump was installed to elevate the tailings to build a wall around the upper end of the valley by depositing sands from a launder built up on 20 foot supports and sloping both ways from the pumping station around the upper end of the basin.

Jan 1, 1950

By Tim Deans

This paper will address methods to manage hydraulic hose and coupling inventory so that parts will be available to build assemblies for the vast majority of equipment with as little inventory as possible. Topics also to be covered will include some basic hose assembly tagging techniques that will help keep equipment running by tracking problem hoses and building ?band aid? kits, having problem hoses premade in stock, and inventory usage tracking (one of the biggest problems for any inventory manager is knowing which couplings have been used so they can re-order). Cradle to grave tracking of hydraulic and industrial hoses insures reliable service of vehicles and ethical disposal of old hoses and couplings. With accountability for disposal of hose products that may contain chlorine (neoprene tube material in some hydraulic hoses) and carbon black that will be scrutinized more closely in the future, a proactive approach should be adopted in order to minimize maintenance facility problems.

Aug 1, 2013

By A. Zrimsek, G. Vingas, R. Wolke

IN 1952, prompted by the great demand of the Canadian drilling and foundry industries for sodium bentonite, the Geological Department of Magnet Cove Barium Corporation, Limited began an extensive search for bentonite deposits throughout western Canada. Their efforts were rewarded in 1958, when substantial deposits of high quality material were found approximately 100 miles southeast of Edmonton, Alberta. The bentonite material, a part of the Edmonton formation in the Upper Cretaceous, is located approximately nine miles south of the town of Rosalind. The land where the bentonite lies has in places .been eroded by stream and glacial action to form a wide gully, convenient for strip mining methods (see Figure 1). The bentonite bed is almost flat-lying, dipping to the southwest at approximately 12 feet per mile. The main bed is 8 to. 10 feet thick and is covered with 15 to 25 feet of overburden. Before stripping, the area is drilled and sampled to evaluate the quantity and quality of the bentonite.

Jan 1, 1962

By P. Blonde

Recent analysis has suggested that a balanced recovery profile can improve flotation bank performance. Test work was conducted to test the balanced profile concept at the Penhorwood talc mine near Timmins, Ontario, Canada. Plant trials were devised to determine how to control the recovery profile and the resultant impact on grade and recovery in a rougher bank of four cells. Accompanying gas dispersion measurements revealed a maintenance issue with one cell that was corrected. By manipulating air and frother addition it was possible to bring the bank closer to a balanced recovery profile and the down-the-bank grade/recovery improved. Plant production showed an increased talc grade at similar yield with the balanced profile. The results provide justification for a long term plant trial.

Aug 1, 2013

By S. Boisvert

Risk-based Inspection (RBI) addresses the challenges associated with ageing plants by focusing the inspection effort on the process equipments with the highest risk, thereby improving plant safety and reducing inspection costs. The RBI methodology is commonly used in the oil industry through the API 581 standard. Since no such standard exists in the mining and metals industry, BPR-Bechtel has developed one using inspection data from process equipments in CEZinc. Models were developed for various damage mechanisms, such as uniform corrosion and stress corrosion cracking. The equations were organized into a user friendly software that facilitates the implementation process.

Jan 1, 2010

By A. C. Stevenson

"The most common theory is that, since thyristors, diodes, and insulated gate bipolar transistors (IGBTs) are “solid state” they will live forever. This is not so. They have wear-out mechanisms (e.g. insulation) and other mechanical parts such as motor bearings. These wear-out phenomena can be easily calculated. In this paper we will look at some of the failures and the failure rate of thyristors in power converters to see what affects them and to see what improvements can be made. If converter failures do occur, some simple forensic engineering steps will show if this is the root cause of the problem.IntroductionLook at the general failure rate curve for thyristors, diodes, gate turn off devices (GTOs) and IGBTs shown in Figure 1. We see that there is an initial high failure rate due to manufacturing defects, application problems, and drive start-up stresses that lasts for a few weeks. This is followed by a long period of (hopefully) several years with a relatively low but very slowly rising failure rate. At the end of this period, the devices start to wear out and the failure rate suddenly starts to increase rapidly over a few months. This signals the end of life for the devices in the system. We will start by looking at this end of life area."

Jan 1, 2000

By John Steele

The goal of this project is to detect the presence of objects behind haul trucks and to provide an alarm to the driver if such objects are detected. Objects of interest include people, pickups, other equipment, and large rocks. Another goal is to see if the system can identify the existence of a berm and determine the distance from the truck to that berm, so a safe backup distance can be computed and used as a reference. This paper presents results that demonstrate that such a system is feasible and includes results from work at a local quarry. Architecture of the system is provided and the various subsystems are discussed. Details of the algorthims are included and discussion of the issues involved in developing a fieldable system are also included.

May 1, 2003

By M. Lebeuf, A. Dumais, C. Farsangi, N. Singh

The Nunavik Nickel project began ramp-up of a new ore body (Expo) in November 2014. This new deposit is significantly more competent than the previous ore type milled (i.e., the plant moved from a feed with a BWI of 12.2 kWh/t to predominantly material with a BWI of 19.6 kWh/t). Despite circuit changes made in advance of the Expo ore ramp-up (grinding media size, mill loading/power draw, and cyclone configuration) the throughput of the plant was bottlenecked at 90% of targeted throughput with multiple stoppages to grind-out the primary mill due to excessive circulating loads. During this time, the secondary milling circuit was under-utilised: therefore the focus for debottlenecking plant production became increasing the product size of primary milling. Given the scope of changes already made to the circuit, it was decided to test the mill in open circuit. The milling changes were modelled using the Molycop Tools package to identify potential problems. In the modelling and plant trial it was apparent that the ball size in the secondary grinding circuit was inadequate, resulting in pebbling. The power draw of the secondary mill was brought up to minimize pebbling and the average ball size was increased. The switch to open circuit primary milling permitted a significant augmentation in plant tonnage. While the overall grinding efficiency decreased using the open circuit configuration, the ability to increase throughput made it the clear operating choice.

Jan 1, 2016

By G. A. Witwicki

"The Thyssen Mining Group of Companies has successfully applied ground freezing technology to numerous projects throughout Europe and North America for over 100 years. Recently, the aspect of data acquisition and data verification has received greater focus.Thyssen Mining has been engaged in several relatively deep shaft sinking projects over the past five (5) years, all of which have required ground freezing to successfully sink through water bearing rock. To safely and economically sink through a quantity of water similar to Saskatchewan’s Potash Mines, it is imperative to understand freeze wall thickness and growth rate.Critical to understanding freeze wall thickness and growth rate, is the collection of accurate data as well as the interpretation of those data. The data can then be utilized to gain a better understanding of the freeze wall growth rate in active projects as well as to provide data to be utilized in modeling for future projects.This paper elaborates on the installation and operation of the data acquisition system utilized at the Newmont Leeville project, Nevada’s first frozen shaft project. In addition, this paper elaborates on the methodology developed by Thyssen Mining to manipulate the freeze wall data derived through the data acquisition system.The successful incorporation of the new system of collection and analysis of freeze wall data for the Leeville Project has given Thyssen Mining a high degree of confidence in the understanding, as well as prediction, of the ground conditions during shaft sinking.This paper will include:•,A brief description of ground freezing and its objective;•,An overview of previous data acquisition methods employed;•,Current data acquisition methods;•,Installation requirements; and,•,Data manipulation and presentation methods."

Jan 1, 2015

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter in blowing the copper stage has been developed to predict the molten temperature. The key assumption of the model was that white metal and gas phases in the converter were in thermal and chemical equilibrium. In this model, the chemical reaction of white metal and oxygen was accomplished completely. So long as sulfur existed in the bath, the generation of Cu2O was frozen. The reaction rate was considered to be constant and controlled by the reacted sulfur. The converter temperature was calculated by heat balances over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depended on process parameters such as oxygen efficiency, molten emissivity and oxygen enrichment.

Jan 1, 2007

By Mory Ghomshei

Pebble Creek Geothermal Power project is associated with a massive recent volcanic eruption in Southwestern British Columbia Canada. Slim holes drilled to depths 1100 m in the prospect area, show very high temperature gradients around 80?100?C/km. The temperature and chemistry of the Pebble Creek hot springs indicate the possibility of a steam reservoir in the prospect area. In addition to high temperature gradients, presence of host rocks with high permeability, along with abundance of recharge waters (from the Lillooet River) provides clear signature of a high-grade geothermal power reservoir at depth 2000 to 3000 m. Data show that over five hundred Megawatt of green power can be generated from the prospect area in a commercially viable manner. The generated power will be base-load, which in comparison with large hydro has the advantage of lower capital costs and a significantly smaller footprint. The final hurdle to overcome, before starting the development phase, is deep exploratory drilling for resource confirmation. This paper is a summary of the data available on the Pebble Creek geothermal power prospect, presented in the context of viability of the resource for large-scale commercial power generation.

Aug 1, 2013

By Hans Lundberg

An electric survey from a 'plane flown over the ground is much faster and cheaper than an electric survey carried out on the ground. The results are obtained as continuous recordings that are resolvable into both a depth expression and a conductivity effect, so that the indications are easier to evaluate, as well as to correlate from one flown line to the other. The prospecting technique adopted in our electric airborne surveys may be brie fly described as follows: A loop of many turns of insulated copper cable is fastened around the fuselage of the 'plane and connected to a generator supplying a few ampere alternating current, usually of a frequency less than 1,000 cycles per second. Just as the current in the primary coil of a common transformer will induce current in the secondary coil when shorted, the alternating magnetic field from this primary current now induces alternating current in electric conductors that happen to be located in the vicinity of the path over which the 'plane is flown. This induced secondary current in each conductive section of the ground causes, in turn, an alternating magnetic field, secondary field, which disturbs or dampens the normal alternating magnetic field from the primary loop flown by the 'plane. These secondary fields are then picked up and recorded by the help of detecting solenoids, amplifiers, and recorders carried in the 'plane. By closer study of such a secondary field it is possible to localize the secondary current causing it and, thereby, the conducting body that contains the secondary current. In the 'plane are continuously recorded, besides the amplitude or intensity of the field, also the phase, which is a measure of how much the recorded secondary field is out of step with the primary field.

Jan 1, 1950

By BRIAN HITCHON

Calcium, magnesium, bromide and iodide extraction from formation waters for use as industrial minerals has occurred in several countries, but not yet in Canada. Potential commercial brine fields exist in th e Upper Devonian Beaverhill Lake Formation of so uthern Alberta, and the Middle Devonian Elk Point Subgroup of north-central Alberta, f rom which calcium, magnesium and bromide are potential products. Iodide contents in fo rmation waters f rom the Upper Cretaceous Belly River Formation and the Lower Cretaceous Viking and Bow Island fo rmations in central and southern Alberta are at the lower range limit of commercial iodide-bearing formation waters elsewhere in the world. Available information is insufficient 10 outline potentially commercial areas in Alberta, but such info rmation can be most easily obtained f rom test borings for shallow natural gas. Lithium is not now produced commercially f rom formation waters but its content should be monitored in view of f uture increased demand for this metal.

Jan 1, 1984

By M. Tanaka, H. Narita, K. Morisaku

"The selective separation of palladium (Pd), platinum (Pt), and rhodium (Rh) from a hydrochloric acid solution by solvent extraction was investigated using amide-type extractants, i.e., N,N,N’,N’-tetra-n-octyl-thiodiglycolamide (TDGA) and N-n-hexyl-bis(N-methyl-N-n-octyl-ethylamide) amine (BisAA). The separation experiments employed two separation schemes: (1) extraction of Pd with TDGA and that of Rh and Pt with BisAA; and (2) extraction of Rh, Pd, and Pt with BisAA. Separation scheme 1 achieved the highly selective separation of each metal. For separation scheme 2, Rh can be recovered prior to Pd and Pt, despite having a lower selectivity for Pd/Pt than separation scheme 1. INTRODUCTIONThe recent increase in the use of platinum group metals (PGMs) in industry (especially auto catalysts containing palladium (Pd), platinum (Pt), and rhodium (Rh)) has lead to their increasing waste; therefore, improvements in the recovery techniques for PGM have received significant attention. In metal refineries, PGMs are mainly separated and purified by solvent extraction (Cox, 2004). The extraction process used in INCO’s Acton precious metal refinery is one of the most famous commercial processes and is utilized worldwide. In this process, silver is first removed as a residue (AgCl), and then gold, Pd and Pt are extracted from hydrochloric acid (HCl) solutions using dibutylcarbitol (DBC), dialkylsulfide (DAS), and tri-n-butylphosphate (TBP), respectively. Finally, Rh remains in the raffinate (Barns & Edwards, 1982).The development of a successful solvent extraction process depends on the choice of the appropriate extractants. We have studied the extraction of PGM using N,N-disubstituted amide compounds (Narita, Tanaka, Morisaku, & Abe, 2004; Narita, Tanaka, Morisaku, & Tamura, 2006; Narita, Tanaka, & Morisaku, 2008a, 2008b). They are relatively stable against acids, and their metal extractability can be improved by changing the side chain length and/or introducing additional donor atoms like sulfur and nitrogen. We have recently found that thiodiglycolamide and an amide-containing tertiary amine have good extractabilities for Pd and Rh, respectively."

Jan 1, 2012

By Long Han, Beijing General Research Institute of Mining and Metallurgy, Yu Xie, Yunhai Zhang, Yangge Zhu, University of Science and Technology Beijing, Yanbo Shang, Xingrong Zhang

"The first-principles method was employed to study the adsorption of hydroxyl calcium (CaOH+) and hydroxyl (OH-) on hematite and quartz surfaces. The calculation results suggested that OH- preferred to interact with the active Fe sites on the hematite surface, whereas OH- adsorbed on the quartz surface by weak hydrogen bond. Though CaOH+ could easily adsorb on the hematite and quartz surfaces by the formation of Ca-O bond, the covalence formed on the quartz surface was apparently stronger than that on the hematite surface, meaning a stronger and more stable adsorption. CaOH+ adsorbed on quartz surface was mainly through the interaction of O-2p and Ca-3d states, and this interaction on hematite surface was weaker.INTRODUCTIONIron Increase and Silicon Reduction Technology (Yu & Duan, 2002) of hematite is mainly through the reverse flotation (silica is floated away from the iron concentrate). There are two ways to achieve this (Houot, 1983). One is to collect quartz by cationic collector directly; the other is to activate quartz by lime and then collect it by anionic collector. There are two main different views with respect to the mechanism of quartz activation: mono-hydroxyl compound theory (Fuerstenau, Rice & Somasundaran, 1965; Fuerstenau & Palmer, 1976) and surface hydroxyl precipitation theory (Hu & Wang, 1988; Wang & Hu, 1990). The former indicated the formation of the mono-hydroxyl complex is one of the two criteria of quartz flotation. The later theory, on the other hand, suggested that surface precipitation is the adsorption of active species of metallic ion on quartz surface. However, most of those researches are based on the solution chemistry of flotation and little is done at the microscopic level.In this paper, by the help of first-principles calculations, the adsorption models, bonding conditions, Mulliken charge populations and adsorption energies of hydroxyl and calcium hydroxyl ions (OH- and CaOH+) on hematite (001) and quartz (100) surfaces were investigated to find out the lime activation of quartz at atomic level, which is significant for the researches of quartz activation theoretically and practically."

Jan 1, 2016

By Katsutoshi Saibara

Network communication note is a cloud system for an earthwork project. It enables backhoe operators and dump truck drivers to monitor their own works in progress currently and performed up to the present, and to have opportunity to reflect on their own bearings in the earthwork operations, and then could increase their situational awareness to the actual work conditions. First, this paper presents problems and purpose. Secondly, the configuration of the network communication note is reported. Thirdly, examples of communications enhanced by the network communication note are shown. Finally, remarks are described.

Aug 1, 2013

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (300 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 130 machine-years of operation at locations in North America and Europe. ST has also installed separators for the beneficiation of industrial minerals in North America and Europe. The technology has been successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, barite, and potash.

Aug 1, 2013

By J. H. Schloen

"One of the most important phases in Canada&apos;s relatively rapid development of its metal mining and refining industries was launched in 1928 when the directors of Noranda Mines Limited decided to establish an electrolytic copper refinery ""somewhere in Eastern Canada”. Noranda&apos;s president, J.Y. Murdoch, had already evolved the company&apos;s ""mine to market"" policy and was determined to prove the economic feasibility of refining Noranda copper in Canada. The time appeared to be ripe as buoyant business conditions continued into 1929. In addition, proven ore reserves at the Horne Mine in northwest Quebec had virtually tripled and the price of copper had reached a healthy 15 cents per pound. Letters Patent incorporating the company bearing the date February 6, 1929 had been granted by the Secretary of State in accordance with an application that specified a capital structure of $2 million divided into 20 000 shares with a value of $100 each. Noranda assumed 70% of the original investment in the proposed refinery, while the Nicholas Copper Company of New York (which later became Phelps Dodge Corporation) and British Metal Corporation Ltd. of London, England, each were responsible for 15%. Nicholas Copper Company agreed to supply the design and to supervise the construction of the refinery and British Metal Corporation would act as sales agent and market the refinery&apos;s products."

Jan 1, 1999

By Marc Piard

In a cool mine, tapping high-pressure lines through reducing valves lowers the temperature beyond remedy. It is the writer&apos;s suggestion that, for low-pressure work, law-pressure air ,should be generated in a compressor installed underground adjacent to the work, and that the jacket-water of the compressor should be utilised for re-heating purposes. Such a system of compressed air distribution, designed especially for service in cool mines, is described in the following notes. The suggested system includes a three-wire pole line from the sub-station to the opening nearest to the working face, with a cable connection extending to the latter from the openings; an electrical centrifugal unit; a reservoir excavated in the ground; and a distribution line, re-heated by jacket-water. As regards the reservoir, it may be pointed out that in many mines there are blind or abandoned tunnels that could be used for the purpose. The centrifugal type of compressed air machine is a comparatively new departure, and it was formerly considered that such a machine, operating at less than 1,000 kilowatts per unit, would be commercially impracticable. At the present time, however, these machines are being built in Europe for as little as 400 kilowatts per unit, and as much as 110 lb. per sq. inch pressure. One advantage which these centrifugal machines have over other types is that they may be driven by plain induction motors, without the help of special starters-a consideration of the first importance where the electrical regulations are severe.

Jan 1, 1926