Search Documents

By S. A. Sadough vanini

In this paper, Stress-Strain-Temperature relations for Shape Memory Alloys are studied. Temperature effects on Shape Memory Alloys are different from those related to ordinary materials. In ordinary materials, elastic characteristics can be assumed to be constant in low temperature ranges, and only the deflection arising from temperature changes could be added to the elastic defection. As long as two phases of austenite and martensite could be present in Shape Memory Alloys simultaneously, elastic modulus follows temperature and temperature gradient. In continue a smart actuator is investigated considering a homogeneous cantilever beam. Beam bending is established by using shape memory wires. An initial strain is imposed to shape memory wires in a low temperature, and then, they are installed in the outer surface of the beam. Therefore, since the temperature is imposed in these wires and they cannot have free recovery strain, the compressive recovery stress will be produced in the outer surface. This will result in a deflection in axial direction of the beam. At first, beam deflection is calculated on the basis of theoretical relations and solving the relevant differential equations. Afterwards, experimental tests are performed on an elastomeric beam equipped with shape memory wires. When a voltage is applied, a temperature rise will occur in the wires; then, this temperature rise causes a deflection in the beam. Finally, the theoretical and experimental results? comparison indicates a good conformity. One capability of this actuator is its high flexibility, and by controlling the inlet current, the end-beam deflection can be controlled.

Oct 1, 2011

By R. T. Erskine

"The No. 6 orebody is located 6 miles from the main op.eration of Brunswick Mining and Smelting Corporation Limited and includes open-pit and primary gyratory crushing facilities. Ore is transferred by truck to the secondary crushing facility at the main plant. About 3,500 tons of ore per day are crushed to minus % in. and ground to 68 per cent minus 400 mesh in rod and ball mills for flotation feed. Conditioning and aeration precede rougher flotation, and four stages of cleaning bring concentrates to a grade of 42 per cent Pb + Zn + Cu. Middling products are reground and refloated in a secondary flotation circuit, producing a cleaner feed and a final tails product. Primary bulk concentrate is treated with sulphur dioxide and steam-heated to l 70°F and the majority of the gangue is floated off, leaving a product that assays 57 per cent combined Pb + Zn + Cu and is suitable for marketing. This material is thickened, filtered, dried and loaded into railway cars for shipment to the smelter. Reagent use on flotation is conventional, with many compromises in dosage required to maintain the recovery of lead and zinc in the most advantageous proportions. Many refinements in the flowsheet have been made since start-up in 1966, and more may be made as laboratory and plant testwork indicate possible improvements."

Jan 1, 1971

By C. R. Kato, G. Proulx

"Within the continuous scenario of reduced aluminium price and plants production costs increase, the energy consumption optimization in the aluminum electrolytic pots continues as the main focus for the producers. Energy consumption was chosen as a key performance indicator to drive the efforts and actions for improvements. Alcoa improved the energy consumption by approximately 3% from 2005 to 2015. This improvement was a result of best practices implementation, new technologies introduction, strategic actions with plant curtailments and management practices. The main objective of this paper is to highlight the importance of the management practices for planning and operational improvements beyond the technology changes. About 10 years ago, Alcoa reorganized its approach to retain knowledge in the Smelters by using a Best Practices format. For each specific subject, a skilled team defined the minimum requirements and the Best Practices for several aspects of operation and maintenance, which affect the environment, safety, cost, customers and performance. These Best Practices were deployed to all Smelters combined with training sessions to process and operation professionals. We will describe how the Best Practices were organized, the deployment strategy used, and the approach to measure the plants’ success. We will describe the management approach that includes Manufacturing Analyses focused on 3-year potential, annual planning, and weekly monitoring of plant stability. A manufacturing analysis is organized at select plants with cross-functional participation of specialists from technical, operational, procurement and finance. The output of a manufacturing analysis includes a roadmap of enablers to improve energy efficiency. A quarterly follow-up of enabler deployment is held with the plant and resources that participated in the analysis. Annually, there is a Planning Process where energy consumption enablers are selected to be implemented during the next 3 years for each plant. A monthly critical analysis is made by the plants with regional best practice support. On a weekly basis, key performance indicators are reviewed with determination of a stability index for each plant. Any deviation signal of unstable condition is alerted and supporting resources are diverted to the plant to reverse trend with countermeasures.INTRODUCTIONDue to factors like excess aluminum in the market and lower consumption in China, the LME price is declining along the last years, as showed in Figure 1. In 2011, the price peaked at US$ 2,400/ton and since then, continues to trend down and approaching the lowest level at US$ 1,500/ton in the last 5 years."

Jan 1, 2016

By W. Lin, Z. Z. Dong, C. L. Zhou, Y. C. Kuang

The inversion of rock mechanical properties based on well-logging data is a common method to drillbit selection in petroleum engineering, the basic principle of which is to use deep-well logging data and experimental regression model to calculate rock mechanical properties. The profile of rock mechanical properties can be established. According to the profile, the type of drillbit can be selected in different formations, which will improve the economic benefit of bit use indicators. Compressive strength of rock is one of the most important parameters. Conventional method to establish regression models of acoustic velocity and uniaxial compressive strength is on the basis of rock core sonic experiments and uniaxial compressive experiments. However, with the increase of deep drilling operation, triaxial compressive strength prediction model will play a more vital role in drillbit optimization selection in deep wells and improving ROP (Rate of Penetration). Triaxial compressive strength is an important parameter to evaluate the formation strength property. In this paper, to the sandstone commonly encountered in oil drilling, combined the rock mechanical experimental results with the changing porosity experimental results under confining pressure, a new interpretation model of triaxial compressive strength based on well logging data is proposed. Firstly, three types of sandstone samples are collected. Then measured components, uniaxial compressive strength, triaxial compressive strength and porosity. Experimental results show that: confining pressure has a significant influence on sandstone strength, with the increase of confining pressure, triaxial compressive strength increase; furthermore, the triaxial compressive strength of different porosity sandstones have different change rules when confining pressures changes; sandstone porosity decreases with the increase of confining pressure and it obeys logarithmic function. According to the results, regression models of sandstone, in-situ uniaxial compressive strength model and uniaxial compressive strength model under normal pressure are generated. Meanwhile, using well logging data in the acoustic velocity, density and gamma value can derive in-situ rock formations uniaxial compressive strength and in-situ porosity. Eventually, a new model established in this paper, containing in porosity, uniaxial compressive strength, lateral pressure and power exponent of regression, can predict triaxial compressive strength which will guide drillbit selection.

Jan 1, 2015

By Kati Tschöpe

Cathode wear has become an increasing challenge in the aluminum industry due to the use of more graphitized materials. Today, there exist no standard laboratory methods for measuring cathode wear where different commercial materials can be ranked. The typical average wear rate in an electrolysis cell is quite small. The aim of this work was to design a test method where the wear could be accelerated compared to industrial cells. It was focused on polarized tests where the cathode is exposed to electrolyte, which gives higher aluminium carbide solubility. The cathode materials were characterized by microscopy and image analysis.

Jan 1, 2011

By E. Best

In 2003, Phelps Dodge Mining Company decided to pursue the design and construction of a Central Analytical Laboratory to provide chemical analyses for their Arizona and New Mexico operations. This centralized approach was selected in place of refurbishing six (6) older laboratories that operated at the various Phelps Dodge sites, and which would not have permitted full automation and use of robotics. The new lab was designed by the Process Technology Center (PTC) Material Characterization Group in cooperation with IMP Group. The Central Analytical Service Center (CASC) encompasses fully automated sample preparation of blast holes and geological samples weighing up to 15 kg/sample. The CASC also includes the first "wet chemistry module" worldwide to be operated by robotics systems to perform Total Cu, Acid Soluble Cu, and Quick Leach Tests (QLT), and a fully automated lab for electrowon copper cathode. The new lab also offers flexibility for handling specialty samples and analyses by either semi-automated or manual mode. Data handling and transfer is accomplished using the commercially available StarLIMS system. Commissioning was accomplished within five (5) months of startup during which the CASC also handled 86% of a full production load. The 24/7 lab operation has already exceeded its design capacity, has achieved considerable savings in operating cost, reduced sample preparation errors, and significantly increased analytical quality.

Jan 1, 2007

By Bahaa Hussein

Considerable number of methods and procedures has been introduced for trending and progress reporting of engineering, procurement and construction projects. This paper introduces a novel method, designed to augment the set of indices for measuring schedule performance. The concept behind the developed method is to provide early warning by dynamically evaluating the schedule cumulative impact of construction projects. The proposed method is designed to highlight the gradual deterioration in schedule status resulting in a cumulative impact due to the aggregation of small delays encountered during the execution of non-critical activities, and can be used as an add-on utility to existing software systems that perform CPM scheduling. The proposed method is based on a developed formulation for quantification of the Schedule Compression Index, which takes into consideration the remaining project activities durations. The index is developed based on periodic comparisons of ?Current Schedules? and the project ?Baseline Schedule? using the summation of the remaining activities durations. A numerical example is presented to demonstrate the application and capabilities of the developed method. It is expected that the developed index together with other schedule performance indices would be of value to decision makers and members of project teams.

Aug 1, 2013

By W. Standifird

"Cohesive fracture is a mechanical model widely used for modeling quasi-brittle fracture in rocklike materials. This work discusses use of this model to simulate quasi-brittle fractures generated by injection stimulation during the process of cuttings reinjection in West Africa. Cuttings reinjection is an engineering practice used for disposal of drilling waste. During this process, hydraulic fractures are created at the target formation and milled cuttings are injected with fluid. In practice, this process must remain in compliance with environmental regulations and zero-discharge policies. The purpose of this study is to determine the following factors of injection design for a field in West Africa: (1) pumping pressure capacity required to successfully perform the injection and (2) the injection rate for injection performance and the value of fracture width under injection.A simplified three-dimensional (3D) finite element model (FEM) was built. A poroelastic plastic damage model was used for simulation of the cohesive crack prorogation within the target formation. For simplicity, fracture development in both horizontal and vertical directions was simulated separately. In this way, the computational burden for one calculation was reduced to a reasonably low level, without losing accuracy of the model. Loads of the model include fluid injection and gravity, which balances the initial geostress field. Various values of injection rate were used in these calculations to determine the most reasonable value of injection pressure. The capacity of pressure of a pumping device was determined using this optimized value of injection pressure.Results in values of width and length of fractures created by the injection are presented. Injection pressures at bottom-hole (BHP) corresponding to each value of injection rate are also given. Numerical results for fracture generation and propagation in a horizontal direction were visualized. The pumping pressure capacity required to fulfill the cuttings reinjection work was determined based on the numerical results of optimized injection rates and pressure. The fracture width was determined using the given pumping pressure. The length and height of the fractures was determined using pumping pressure along with the required volume of cuttings waste to be disposed of into the formation.This work presents a case study of 3D finite element modeling of hydraulic fracturing generated by cuttings reinjection. The results of the optimized injection rate and pressure provide a best practice and a useful reference for cuttings reinjection analyses in this region."

Jan 1, 2015

By Z. Zhang, D. Bouchard, H. Blanchette, A. Lemieux

This paper describes quality control methodologies for the production of semisolid A356 aluminum slugs with the SEED process. A methodology based on destructive tests carried out with an apparatus measuring the force to slice the slugs is presented. The force measurements were correlated with the solid phase morphologies of the slugs and were validated against a non destructive methodology that consisted in monitoring the temperature evolution of crucibles to produce the slugs and the drained metal. Results from the destructive and non destructive methodologies are compared and discussed.

Jan 1, 2006

By John A. Legge Jr.

"ACCOMPANYING Alberta's great natural endowments of oil, wheat, scenery, fishing, and hunting is also a generous endowment of geophysical problems to plague the interpreting geophysicist. These problems — by no means unique to Alberta — are sufficiently numerous and outstanding to be of major concern in exploration. Some of them have been adequately solved, others are well on their way to being solved, and still others remain almost completely unsolved. Often a problem readily solvable in one area can be solved only with great difficulty in another. Many are closely allied with the geological conditions and require the best co¬ordinated efforts of the geologist and geophysicist for their solution.It is a fairly general practice to study rather carefully the geophysical characteristics of known producing reefs in order to obtain data on which to base an interpretation of unproven areas. This practice obviously has a very sound basis, for, as discoveries become more and more widespread in the Alberta basin, it is found that the variation' in geological conditions has a marked effect on the seismic results, as would be expected. By carrying this analysis over an area it is possible more and more to anticipate the geophysical picture which should be obtained in connection with reefing under the varying geological conditions. Another phase of this procedure, and one that has received less attention, though it is certainly of importance, is the analysis of the all too numerous failures. A study of these failures may be more fruitful than a study of the successes for it may indicate weaknesses of field procedure, computations, or in¬terpretation not particularly obvious in the discovery areas. These studies must not only include the geophysical characteristics of the observed `anomalies', but should also be coupled with a thorough geological study to ascertain whether some unanticipated geological condition is responsible for the erroneous geophysical interpretation."

Jan 1, 1953

By W. M. Tupper

Municipal governments recognize the importance of aggregates in the local economy and the need to manage this resource in the interest of the public good. They have encountered problems with regulating the industry and the dichotomy between the urban need and the rural source. They have suffered from a lack of financial benefit, an adequate aggregate inventory, provincial strategy, economic information and public understanding. A provincial strategy for ensuring the availability of aggregate supplies to developing areas of the Province is essential. The Province should also be responsible for licensing, research, technical expertise on rehabilitation, public education and financial assistance. Upper-tier municipalities (regions or counties) should assume responsibility for resource management, including resource availability, demand characteristics, truck routing, phasing of resource development and sequential land-use planning. Area municipalities (towns and townships) can best determine the social and environmental impact of a specific aggregate development proposal and should therefore have the primary responsibility for the location of new pits and quarries. They should also have the authority to supplement provincial regulations concerning operating standards and the phasing and standards of site rehabilitation.

Jan 1, 1978

By S. Duvah Pentiah

The transformation of an open pit coal mine to a horizontal-punch underground mine is subject to a number of challenges. These include scheduling the operation of various sizes of trucks over a long period, as well as updating delivery routes and dump site locations as the mine transformation progresses. In this process, rock is excavated from a quarry through earthworks. The bulk earthwork and quarry material delivery were initially drawn from traditional planning and experienced issues in their early phases. As a result, a traffic simulator was developed in order to validate schedules and predict achievable throughput, likely delays or blockages in the long term. The dynamic traffic simulator was also used to provide traffic density and vehicle arrival data at selected intersections in order to identify possible safety and efficiency issues.

Aug 1, 2013

By N. Behnood, W. Pascheto

"Laboratory wear tests are important tools that can be used for the evaluation of materials for wear applications and mitigation of wear problems in the mining industry. However, laboratory test parameters must be fully characterized and test results must be carefully interpreted if a material selection is to be made. Failure to do so may lead to erroneous conclusions. Suitable lab-oratory tests are valid only if they reflect the field conditions to which materials are subjected. Therefore, it is important to know, in detail, the field conditions, as well as the wear test techniques being considered. It is important to recognize the limitations of the various wear tests and the wear test data published in the literature. This work will review present wear testing technology, including the various wear tests avail-able, wear test equipment and test limitations. Several wear test procedures will be related to common equipment used in the mining industry.IntroductionThis paper will concentrate on non-lubricated wear mechanisms, because they are the most costly to the mining industry. Very frequently we are faced with the task of selecting materials for wear applications or improving existing systems that are giving poor performance. There are plenty of examples in the literature of practical wear cases and ranking of materials for wear applications. It is also very common to find materials manufacturers’ data -sheets listing wear tests results by comparing their materials performances against those of competitors. Much of the published wear data lack the description of the type of wear test, test parameters and the type of wear mechanism to which the data should be applied (if any).Before considering wear test data for a specific problem one should ask which type of wear mechanism is involved? What type of test and what test parameters were used to produce the results? Even if the type of wear tests and parameters are known, how accurate and useful are the published wear data? How are the results related to a particular type of wear? It is important to point out that even the standardized wear tests, such as those in ASTM standards, have limitations. Such limitations are recognized and clearly spelled out in the standards themselves. Basically, wear tests may lead to erroneous results if the test is not able to repro-duce the same wear mechanisms encountered in the field. Therefore, the use of published results may be helpful, as a starting point, but may be of little value for a final material selection.This work will discuss the main types of non-lubricated wear mechanisms encountered in the mining industry. In addition, it will discuss the many wear tests available and their correlation with the various types of wear mechanisms. The limitations of several standardized wear tests and the limitation of using published wear data will also be discussed."

Jan 1, 1997

By G. E. Veins

This paper summarizes an investigation in which beneficiated ilmenite ore was smelted in a continuous, three-phase, 250 kv.a., open-top electric furnace. Minus %. inch ore was smelted, using the standard method. Fine ore, in the order of minus 14 mesh, was smelted in the briquetted form by the open bath method, and in the unagglomerated form by the cold dry-top method. The latter was shown to be superior. The data obtained .are discussed at some length. During the investigation, slag aver-aging 82.5 per cent Ti02 was produced over a period of 87 hours, the maximum being 85 per cent. Such slag should .be particularly attractive for the production of titanium tetrachloride, from which titaniurn metal is produced. The advantages of using paper-mill bark for producing a furnace charge of low bulk density, as required in cold dry-top smelting, were emphasized.

Jan 1, 1957

By Lewis Finch

Oil and .gas reservoirs exist under pressure within the pore spaces of rock structures or traps. Wells are drilled to produce these reservoirs. Under primary operation, the natural energy of expanding fluids in and adjacent to the reservoir forces or drives oil and gas to the wells. There are three basic sources of energy: dissolved gas, water, and gas cap. Typical recovery by primary methods is only 10 to 25 per cent of the oil in place for the dissolved gas drive but is generally higher for the others. Secondary recovery involves the injection of water or gas to supplement natural energy, thereby increasing recovery over that obtainable by primary operation alone. In many cases ultimate recovery with secondary methods is 1.2 to 2.0 times the expected primary recovery. The type programme adaptable in a field depends on its 'primary performance and on certain reservoir characteristics. In the United States, application of secondary recovery methods is becoming increasingly important. About 22 per cent of United States oil production now comes from fields in which injection projects are operating. In 1953, nearly 1.4 million barrels of oil daily came from such fields, more than double the amount in the early 40's. Ultimate primary recovery from known pools is estimated at roughly 73 billion barrels. Secondary recovery projects already in operation will increase this to almost 80 billion, an increase of almost 10 per cent. Unitized secondary recovery projects have been very successful. From unitized projects alone, industry reserves of oil in the United States have been increased by 3 1/2 billion barrels. In Canada, secondary recovery has not been so wide spread mainly because D-3 reef reservoirs which have held the major reserves are under water drive. However, appreciable amounts of water are being injected in the Redwater D-3, Leduc D-2 and Joarcum Viking reservoirs, and gas in the Golden Spike D-3. In both countries, possible achievements in increased recovery through secondary recovery methods now in use and by new ones which may be developed through research and field trial are a challenge to the scientist and the industry.

Jan 1, 1956

By K. W. Major

"This chapter outlines the organization of mine/ mill complexes in Canadian mining companies. Many factors unique to the Canadian mining industry will affect the design of the organization in the future: geographic location, the size and the type of orebody, etc. Mining companies cannot choose where new operations will be located, that is dictated by the location of the orebody. New mines are seldom started near established communities. Rather, the towns usually grow up near the mines. The remoteness of most Canadian mining operations has caused severe problems in attracting and/ or retaining all levels of employees. This means that training has a high priority within each operation.Another factor affecting mine/ mill organizations is the size of the operation. Larger operations generally require more departments and increased specialization to manage equipment and manpower effectively. Thus, for mine/mill complexes, organizational charts are less standardized than in other industries. It is often necessary to organize around the work force rather than develop a chart and then acquire the trained personnel to fill the diagrammed positions.The information presented in this chapter has been derived from the responses received from a survey of Canadian mining operations.Principles of OrganizationOrganization can be defined as deployment of personnel to accomplish definite goals. In the mining industry, the major goals are typically the projected number of tons and grade of ore mined on a daily, weekly, monthly and yearly basis. Organizing involves establishment of authority relationships with provisions for both vertical and horizontal co-ordination within the company structure. Vertical co-ordination is the delegation of responsibility and communication of goals and reporting of progress between the supervisor and subordinate. Horizontal co-ordination is communication between departments at positions of equal authority to determine methods of achieving predefined goals. The organization structure must reflect the objectives and plans of the company, and must clearly define areas of authority.Two criteria for effective organization are departmentalization and manpower planning."

Jan 1, 1989

By T. Loos

The Norddeutsche Affinerie operates an Outokumpu-Flash-Furnace as a smelting unit. The pyrometallurgical slag cleaning process is based on the slag reduction and settling in the electric furnace. Since 1972 when the slag cleaning furnace was built the throughput could be increased fourfold. However, an extensive optimisation effort is required in order to keep the copper loss low. A parameter study with a neuronal network model based on real process data was conducted to identify parameters impacting on the copper loss in the slag. It could be demonstrated that the main parameters responsible for copper loss in the final slag are fixed parameters of the flash furnace. For a better understanding of the copper loss in the electric furnace microscopic analyses of the slag structure and viscosity measurements were performed. Based on these results the reduction and settling of the copper containing droplets could be increased in both pilot plant studies and industrial scale. 4

Jan 1, 2007

By H. A. Oaks

FROM 1921 to 1939, the aeroplane played an increasingly important role in Canadian prospecting and mine development. This service has been interrupted by the war, but undoubtedly it will be accelerated in the postwar years, if suitable aircraft are available. The purpose of this paper will be to review the uses to which the aeroplane has been put in prospecting and development in the past, and its future possibilities as an aid in prospecting. If by review, and deduction, we get a clear picture of what we expect the prospecting plane to do, we may be able to arrive at a very close approximation of its required characteristics and, from this, an idea of costs. 'Function' is defined as the mode of action by which it (the aeroplane) fulfills its purpose. We will endeavour, therefore, first to find what this purpose is, or should be, so that our expectations will not be too limited nor too great-and then find, by analysis, what performance we require in an aeroplane to meet our reasonable expectations at an economic price.

Jan 1, 1945

By F. N. Smith

The carbon steel casings of Heat Recovery Steam Generators (HRSGs) in a co¬generation plant were found to have developed cracks that originated on the inside surfaces. The HRSGs receive hot exhaust gases from the primary Gas Turbines (GTs), which are fuelled with pipeline natural gas. The GTs was initially operating without any suppression of nitrogen oxides (NOx). After being in service for about two years, some of the cracks were found to have penetrated right through the 1/4 in. thick casings. The casings are fitted with insulation on the inside (hot gas side). Examination of steel samples cut from the casing walls revealed (i) fine cracks propagating through the steel from the inside surfaces, and (ii) the presence of relatively large amounts of nitrate ion on the inside surfaces. It was concluded that the nitrate ions originated from nitric acid that was condensing on the relatively cool walls of the casings behind the insulation. Nitric acid was formed in the GT exhaust gases by the combination of water vapour (formed from combustion of the hydrocarbon fuel and from moisture in the combustion air) and nitrogen oxides (formed from nitrogen and oxygen in the combustion air).

Jan 1, 2005

By S. A. Briggs

Bioremediation has been accepted as a treatment technique for groundwater contamination in subsurface soils and shows promise for contaminated fractured rock environments. Biological growth in fractured rock is expected to occur predominantly as biofilms attach to the fracture surfaces. Biofilms in rock fractures are subject to a complex system of forces and other phenomenon due to the dynamics of the bulk fluid in which they grow. In this paper, through the applications of computational fluid dynamics (CFD) to rock fractures, where the boundaries are rough and the flow is complex, a precise analysis was conducted of the interaction of a fluid flow and the rock fracture. Specifically, hydraulic parameters and velocity profiles of an actual rock fracture were calculated and compared to a fracture of equivalent aperture. From the analysis it is clear that it is important to use more complex models such as the Lattice Boltzmann Method used is this paper to describe fracture flow.

May 1, 2009