Search Documents

By Edward R. Lauer

Energy conservation is an integral part of Canada's energy strategy. We must pursue conservation and energy management vigorously if we are to remain competitive in domestic and world markets, and minimize our reliance on external energy sources. Energy management in industry is discussed from three viewpoints: (l) as a means of directly improving profitability; (2) as a major factor in the supply picture; and (3) as a significant influence on Canada's balance of payments and over-all economic well-being. The Federal role in promoting a voluntary industrial energy conservation program is described.

Jan 1, 1977

By E. Yan, M. Mankosa, E. Wasmund

"Rougher flotation in sulfide ore applications is typically performed using conventional flotation machines. The trend over the last 100 years has been for these cells to become larger in volume with cells reaching sizes of 600 m3 and in some cases even larger. The associated foundation loadings, transport and installation requirements along with building size have also increased. In an economic environment where projects must be executed with dwindling capital supply, bigger is not always better. More recently, industry is being challenged to identify new technology that allows for improved flowsheets and financial returns through efficiency gains. To meet this challenge, a novel high-intensity two-stage flotation system known as the StackCell™ was tested to potentially achieve installation volume and required retention time gains when compared to conventional flotation circuits. The results from on-site pilot scale work conducted on typical copper concentrator rougher flotation feed showed retention time gains on the order of 6 to 9 times when compared with conventional flotation equipment. This finding has the potential of reducing capital demands for rougher flotation circuit designs when incorporating the StackCell. The results from test work will be discussed in this paper showing comparative test data generated with a Denver bench batch test, pilot StackCell and large conventional cells, all receiving the same feed.INTRODUCTION Over the last few years, a number of flotation devices have been described as two-stage or multi-stage flotation units. The idea behind multi-stage flotation devices is that flotation performance can be improved by utilizing cells with multiple specialized units in series, but not all units of the same type, as is practiced in trains of multiple tank cells or columns. Instead, each unit is specially designed to provide the optimized fluid environment for each stage of the sequential flotation process. This idea has been proposed based on a study of the fundamentals of the flotation process, and the realization that the process consists of discrete sequential processes, that are each optimized with dissimilar process conditions (Finch et al, 1995), (Zhou, 1996). Instead of executing each step simultaneously in a homogeneous fluid environment, where the conditions would be a compromise between particle collection and froth recovery, the multi-stage flotation unit operates in a set of segregated process environments, each with a set of conditions optimized for that step."

Jan 1, 2018

By R. E. Legg

This paper gives a brief outline of the mining and milling methods which will be used on the Stirling zinc-lead-copper ores by Stirling Mines, Limited, who have for the past two years been developing the Stirling mine in Richmond county, Nova Scotia, and who will bring the mine into production in November, 1929. No attempt has been made to give the paper a detailed technical character, for the main reason chat, since base-metal mining is something new in Nova Scotia, it is felt that a general description would be preferable before this Society, whose membership is mainly made up of chose engaged in the coal mining and associated industries. Furthermore, as both mining and milling operations will be governed to a certain degree by the experience gained after production commences, there are many points which cannot be definitely stated now. GEOLOGY Before discussing the mining methods, it is desirable to present a general picture of the geology and occurrence of the ore-bodies. The surface rocks in the vicinity of the mine consist of rhyolites of .pre-Cambrian age. These volcanic flows outcrop in very few places, usually along' the beds of creeks or on the shores of the numerous small lakes. Consequently, a detailed geological map is not available. The exploration work carried out to date has revealed a sheared zone extending through the volcanic flows for a distance of over 1,000 feet. Along this zone, there has been a replacement of the rhyolites by a carbonate rock for widths varying from 50 to 230 feet, and it is in this carbonate formation chat the mineralization at a later date took place.

Jan 1, 1929

By J. K. Gowans

The Research and Design group of the Project Development Division (PDD) of Placer Dome Inc. includes metallurgical, electrical, civil and mechanical engineers. They provide metallurgical research and conceptual flowsheet development, feasibility concepts for the processing and ancillary facilities, and manage the detailed design of the facilities once approval has been given to a mining project. This paper describes how this group works, within the Project Development Division, to help develop feasibility studies with the Evaluations Group, manage detailed design, and provide support for the Construction Group. The paper briefly reviews the history and growth of the group and describes how it is evolving. The role of outside engineering firms and how they are incorporated into the division’s objectives are also discussed. The paper highlights the differences between Placer Dome’s Project Development Division and other mining groups, and why this approach fits the way Placer Dome does business.

Jan 1, 1998

By J. Hedderson, J. Starkey, S. Reeves, B. Hilscher

"As ore sorting becomes more common, it is important to quantify its impact on comminution circuits in order to precisely predict its effect on throughput, grind, and mill operating conditions. Since sulphides and other valuable minerals are often softer then the surrounding waste rock, the ore kept by a sorting system is typically softer than the average ore. In order to accurately forecast production, new measurements of hardness need to be performed on the new concentrated mill feed. This paper proposes a methodology to examine this effect quantitatively at an early stage of project development using the SAGDesign test.INTRODUCTION The application of ore sorting in the mining industry is one of the most promising recent technologies with the potential to cause step change in the way concentrators are designed. Most typically, ore sorters are used to sort a given ore flow for grade, either to reject waste from the mill feed, or rescue ore from the waste pile. Ore sorting technologies have been successfully applied at many mining properties in various forms and while the technology has reached or is reaching maturity in other industries, it is still in development in the mining sector. As a result, there is not yet a general consensus on the considerations that need to be made when designing a plant with ore sorting from a feasibility level above and beyond what is commonly performed as best practice. This paper will discuss those considerations and propose a methodology for integrating ore sorting into a comminution circuit at the design phase. Due to the linearly additive nature of the SAGDesign Test results, a “hardness balance” can be developed to estimate the ore hardness which would be measured in any sorting mass split using only two data points. This will allow a design engineer to make more informed decisions as to the most appropriate mass split to select in relation to the incurred operating costs and grinding circuit sizing."

Jan 1, 2019

By John A. Teeter

"A SHORT WHILE AGO I enquired about The Mining Society of Nova Scotia. In all honesty I was apprehensive about addressing such a body if it was highly geared to the technical aspects of discovering and obtaining mineral resources. I was told that this would not be the case. Rather, there would likely be in attendance a broad cross section of people from business, industry and government and from across Canada and the U.S.A. Thus there would be an interest in a free-wheeling discussion of the prospects for industrial development in Cape Breton. Accordingly - being one who hates to miss an opportunity - I intend to exploit the invitation of your executive by being, over the next short while, frankly promotional. I would like to talk about what I consider to be some of the most important attributes of Cape Breton for industrial development and identify some of those prospects. Secondly, I will quickly review some of the things the Cape Breton Development Corporation is doing these days to stimulate some of that industrial development."

Jan 1, 1972

By Gordon L. Draeseke

"Before getting into more specific aspects of my talk today I should put in one disclaimer - one week in Mainland China and one day with Premier Kosygin does not make me an expert on Sino-Soviet affairs nor on Canadian-Chinese relations. Perhaps though there is a message in the fact that one meeting took place in relative openness in China and the other was at least partly in a bullet-proof limousine in Canada. I thought it might be interesting and appropriate to explain something of the forest industry to you who are engaged in the mining industry. Our industry, like yours, is based on a natural resource and the basic activity that we engage in is the extraction and conversion of that resource into saleable materials. However, the fundamental difference between our industries is that our resource is on top of the ground - easily visible and easily measurable, whereas yours is under the ground - difficult to find and, having been found, expensive to measure. A second difference is that ours is renewable while yours is extractive, and you must keep finding more to keep up reserves."

Jan 1, 1971

By Cindy Schiewek

Industrial injury occurrences are an ongoing concern for Mine Operators. Along with the personal suffering of injured workers comes an increase in compensation and productivity costs. Growing recognition of repetitive stress and bodily injuries, accompanied by recent studies, validates the assumption that a relationship exists between ergonomic injuries and machine design. Intuitively, there is a belief that an ergonomically designed machine will reduce repetitive stress injuries through design and education however; quantifying this belief has been a challenge for Mine Operators. Sandvik Tamrock has undertaken a project aimed at developing a business model to assist in quantifying the benefits of ergonomic intervention. This model focuses on distinguishing and quantifying this method of intervention to allow for a better evaluation of the machine. For simplicity, the project initially focused on the Face Drill Jumbos. The target of the project was three fold: !" Recognition of the cost drivers for compensation; ergonomic injuries !" Identification of the relationship between ergonomic machine design, and the decrease of the negative effects associated with the cost drivers !" Systematic prioritization for ?prevention by design? The project findings substantiate the expected reduction in injuries and compensation claims. Based on all ergonomic intervention studies conducted, each case showed a reduction in compensation cost; through prevention by design, one can reduce the amount of potential risk. The paper addresses the resources and methodology used, along with the findings and its relevance to the issues that face the Mining industry.

May 1, 2003

By J. G. Phillips

Introduction Throughout the Great Plains region (the provinces of Manitoba, Saskatchewan, and Alberta), numerous clay deposits of widely varying composition and character are to be found. These may be classified into two general types: (1) surface clays, and (2) shales. The surface clays consist of a heterogeneous mantle of silts and clays interspersed with grave! and sand deposits, and may belong to any of the following groups: (1) lake clays: (2) river-terrace or flood-plain deposits; (3) delta deposits . In most cases, the water from which these deposits were ' laid down was derived from the melting ice of the continental glaciers. These surface clays, in general, possess certain characteristics in common, being all more or less calcareous, often silty, and showing a tendency to 'check' in air-drying. The shales found in this region are of Cretaceous and Tertiary age. These deposits have a wide extent, but there is frequently such a heavy covering of drift material that the clays are accessible chiefly along the walls of stream valleys, or along the escarpments of uplands.

Jan 1, 1929

By J. H. Sokolowski, R. I. MacKay

The level of Si and Cu in the 3xx series of alloys affects the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase. The volume fraction of these phases in turn affects the feeding conditions during solidification and ultimately the Area Fraction Porosity and Mean Pore Diameter measured in the as-cast structure. This work sets out to establish the relationship between the volume fraction of the a-Al dendritic phase and the Al-Si eutectic phase and the resulting porosity that forms on the Monotonic and High Cycle Fatigue properties. The alloys in question are the Al-9%Si-l %Cu and a Al-7%Si-4%Cu alloys which were cast into V8 performance engine block castings and then heat treated to achieve desired mechanical properties. The engine block castings provided the mechanical and metallographic test samples analyzed for this work.

Jan 1, 2006

By Laura Kelsey

Contaminant Robust In Situ Water Extractor CRIWE Nafion-based water clean-up Extract purified water from natural extraterrestrial sources In situ water processing for downstream electrolysis Chemically resistant to process contaminants such as acid

May 1, 2013

By H. A. Wilson

Introduction Salt (sodium chloride) occurs naturally either in the solid state as rock salt or in solution as a component of natural brines. It is the major saline constituent of sea water, which contains about 4 percent salt-roughly 164 million tons, or enough to meet world salt demands for five years, per cubic mile. The great rock salt deposits of the world are generally regarded as having been formed by the evaporation of sea water over long periods of rime in wholly, partially, or periodically cut-off bays of ancient oceans. History and Occurrence of Salt in Canada We can speak today of the vastness of Canada's salt resources, but it was not always so. Settlement of our Atlantic seaboard and the Sr. Lawrence valley began in earnest in the early 1600's. The first small commercial salt works in Canada did not come into operation until 1866. Thus, for some two and a half centuries, the inhabitants of this growing country were entirely dependent on foreign sources for every pound of salt they consumed. The record shows that from at !east 1800 onward, the need for a domestic salt industry was clearly recognized by the governments of the day. It was during the Western Ontario oil-boom of 1866 that the initial discovery of rock salt in Canada was made, not far from Goderich, at a depth of 1,000 feet. A salt company was promptly organized, and with their operations there began the gradual and still uncompleted conquest of the Canadian salt market by the Canadian salt industry. Over the next thirty years many holes were drilled into the Salina formation both in Ontario and Michigan, and encountered rock salt. A vast salt-basin was disclosed, approximately outlined, and given the name Ontario-Michigan Salt Basin. The Ontario portion of the basin extends over at least 3,500 square miles, is met with at a depth varying between 800 and 1,600 feet, and has a thickness of 50 to 250 feet. No attempt has ever been made, so far as we know, to calculate the total salt reserves of this basin, but the minimum indicated in the Ontario portion by the figures just cited is just under thirty-five cubic miles. The specific gravity of rock salt is 2.2. From these data, those so inclined may calculate the tonnage.

Jan 1, 1947

By Loui Geoffroy, Philippe Gaultier, Martin Piotte, Claude Coache, André Drouin

"Automatic driving at high speed of an underground truck was tested at Brunswick mine in September 1995. Modifications to the truck included: a remote interface to control actuators, front and back video cameras to follow a roof mounted optical guide and proportional hydraulic controls on the steering.The mathematical model of the hydraulic system was adjusted using least square regression. The steering data, used in calculating the regression parameters, were acquired from the moving truck. The automatic steering control used three measured variables: lateral deviation, angular deviation and steering angle. Lateral deviations are obtained using the cameras, which are in continuous view of the guide, while steering angles are acquired from an extensiometer placed at the articulation point of the vehicle. Gain scheduling was used to compensate for vehicle speed and available hydraulic flow. Non-linear characteristics of the modeled hydraulic system were offset using open loop compensation.Speeds up to 23 km/h in forward direction and 13 km/h in reverse were achieved deviaduring continuous testing along one of the mine’s production drifts. Proportional steering was essential in achieving high speeds, as it enabled more precise positioning of the vehicle’s steering direction while reducing the abuses on cylinder and cylinder pins via diminished oscillations about the optical guide at high speeds."

Jan 1, 1997

By S. Dominguez, E. Gebrehiwot, S. Richardson, S. Sandoval

Copper electrowinning/electrorefining (EW/ER) is powered by direct current (DC) rectifiers that typically generate 30,000 to 70,000 amps and a bus-bus voltage of 200 to 500 volts DC. Tankhouses are designed so that DC current flows through “cell lines” which contain individual EW/ER cells electrically connected in series. Electrolyte composed of copper sulfate and sulfuric acid in water forms the “liquid conductor” that connects the metallic conductors in this circuit. In this setting, stray current is a DC current that strays from and therefore bypasses the tankhouse circuit by finding a path to ground, often through the electrolyte in pipelines that feed into and discharge from the cells, or through dried electrolyte (i.e. sulfate), which is also electrically conductive. Tankhouse workers can be exposed to shock hazards if they become part of a stray current path to ground. This presentation details examples of stray current shock hazards in electrolytic tankhouses and provides voltage and amperage measurements associated with stray current in these examples. A review of critical safety controls in EW/ER tankhouses that will mitigate the risk of employee shock from stray current is also provided. INTRODUCTION Electrolytic tankhouses are designed to deliver relatively large amperages of DC current to a series of electrolytic cells in which copper is plated out of solution using the classic anode-cathode pair geometry within each cell. Electrolyte is the “liquid conductor” that transfers current in between the metallic conductors of the cell. The metallic conductors include inter-cell copper bus bars and the anodes and cathodes themselves. It is sometimes forgotten that electrolyte as a conductor is capable of delivering DC current outside the designed circuit of a tankhouse. Stray current is a DC current that strays from the tankhouse electrical circuit by finding a path to follow other than the designed path. Safety becomes a concern when there is a risk of an employee becoming part of an accidental stray current path, thereby suffering an electrical shock. In 2016, Freeport-McMoRan (FMI) suffered a fatality at one of its copper electrowinning tankhouses. The forensic analysis concluded that stray current from the tankhouse rectifier contributed to the fatality. An employee accidentally fell into contact with a metal flange at the end of an HDPE pipe that was collecting cell overflow electrolyte from the tankhouse. DC current passed through the employee to ground, creating a shock that was judged to contribute to his death. The situation was exasperated because the employee was unconscious, and therefore was exposed to the stray current for several minutes before being found. In addition, the employee’s clothing was saturated with liquid, and the employee was found kneeling in puddled liquid on the ground. FMI immediately began an investigation into the root cause of the stray current that was measured at the scene. Sufficient electrolyte had accumulated in the HDPE pipe such that a continuous path was formed between it and electrolyte that was continuously overflowing from energized electrowinning cells. The metal flange on the pipe was the metallic conductor that carried the current to the employee from the electrolyte inside the pipe. Current then flowed through the employee to ground. Because of this incident, FMI undertook an extensive review of the hazards of stray current in EW/ER. FMI’s tankhouse workforce received a Tankhouse Electrical Safety training course developed in- house to insure worker understanding of stray current hazards. Tankhouse design changes were implemented to better insulate workers from stray current. Personal protective equipment (PPE) standards were also reviewed and changes made.

Jan 1, 2019

By Robert P. Dufresne

Electrolytic cells are used in electrowinning (EW) and electrorefining (ER) of non-ferrous metals such as zinc and copper, and are a critical part of the purification process. The cell is a large basin and has an electrolyte or aqueous solution, an anode and a cathode, an insulator, and incoming high amperage. Cells are exposed to unfavourable internal and external factors that have a direct impact on their lifespan. Their deterioration can be caused by incorrect polarity, insufficient magnitude, their construction, tension stress, thermal shock, corrosion and other, and their maintenance and replacement can be time-consuming, costly, difficult and environmentally unsafe. Occupational health hazards and dangers posed by the maintenance and removal of the cell should also be taken into consideration. Modifying the design and fabrication method of the cell, using chemical-resistant reinforcement, and increasing tensile and mechanical strength will defer maintenance for a very long time. This can be achieved by a double hull system that comprises full-length composite reinforcement, polymer concrete reinforced with fiberglass pultruded rods and rebars, fiberglass structural layers, and special resin matrices. This will provide protection against thermal shocks, corrosion, leakage, cracks. The design of this cell incorporates a lifting system that will afford quick and easy install without having to move a great number of cells in close proximity, since it is strong enough to stand on its own and not have to be bonded to adjacent cells. As well, the cell can be anchored with ease as it remains stable. This is especially important because space is limited to lift and manoeuver between the cell and the double-girder overhead travelling cranes. The lifting system can also prevent electrocution and loss in product quality, while increasing efficiency and safety in the workplace. Considerable savings in terms of production downtime are also part of the equation. INTRODUCTION Maintenance and replacement of electrolytic cells in electrowinning and electrorefining are operations that pose many challenges, health and safety concerns, and give rise to substantial operational costs. These problems have existed since time immemorial. Electrolytic cells are made of conventional concrete or polymer concrete, and because of the very nature of their composition and their exposure to severe and environmental conditions, their lifespan is short. Although polymer concrete is composed of high-quality materials, and has good thermal stability and resistance to chemicals, nonetheless, maintenance is frequently required in order to maintain the integrity of the cell and to ensure the quality of refined metals. Repairing concrete is a non-permanent solution as cracks will reappear, and every repair weakens the integrity of the cell a bit more, until it reaches a knock- down point and the structure is compromised. The cell needs to be replaced, otherwise the cell will collapse.

Jan 1, 2019

By I. V. Kojo

Continuous development of technologies has been self-explanatory for Outokumpu Technology's engineers for decades. The aim in the development has always been the improvement of profitability of the copper production but also the sustainability of the processing i.e. high copper recovery, low external fossil based energy utilization, high emission captures and of course low operation and investment costs. Outokumpu Technology's long-term view of the development is a change towards continuous processes and elimination of number of unit operations in smelting i.e. elimination of possible sources of emissions. Outokumpu blister smelting processes i.e. Outokumpu Direct-to-Blister Flash Smelting and Kennecott-Outokumpu Flash Converting have shown excellent operational results during the years of operation and it is expected that soon more than 10 % of the world primary copper is produced by these technologies. The paper will give some background of this development trend.

Jan 1, 2007

By K. J. Boser

"Medium Voltage (MV) metal clad switchgear is referred to as the voltage class from 2.4 kV to 38 kV. Technological advances in circuit breaker designs over the last 20 years have given rise to retrofit options in lieu of complete replacement for older outdated circuit breaker technology. This paper examines the four MV breaking techniques that exist in industry and investigates various retrofit versus refurbish options for switchgear modernization and life extension. IntroductionThe life extension and upgrade of medium voltage circuit breakers is becoming an increasingly important issue in today’s modern industrial facilities from both a reliability and safety standpoint. Unscheduled downtime, loss of production, and plant safety issues are just some of the concerns that need to be addressed with aging switchgear. A thorough examination of the available breaking mediums allows an informed decision to be made when the time comes to assess equipment performance. If you look back over the history of medium voltage breakers, you will find that there have been four breaking techniques developed and widely used:• air magnetic;• minimum oil;• vacuum; and• SF6.Many facilities that were constructed 25 to 30 years ago relied on air magnetic or minimum oil circuit breakers in their distribution systems. At the time, these were the only “tried and tested” options and they afforded good service. Since then, however, newer technology has given us the vacuum and SF6 mediums which have both proven their reliability and monopolized the market. All the methods have their particular place in industry and what follows is a summary of the advantages, disadvantages, and chronological development of each breaking technique."

Jan 1, 1998

By Dan Miners

"This presentation will provide an overview and understanding of Mine Safety and Health Administration (MSHA) and Ontario Regulations for Mines and Mining Plants. It includes discussions on the history and practical development of the standards and an overview of engineering best practices from a construction, maintenance and operational viewpoint. INTRODUCTION Ontario is one of the safest mining jurisdictions in the world and has some of the most comprehensive regulations for the construction, operation and maintenance of a mine. In the USA, several operators have adopted some or all of the practices prescribed by the Ontario Regulations as an internal procedure. Experience has demonstrated that these plants are indicating less unplanned downtime and fewer issues with MSHA inspectors in their hoist plants. HISTORY AND THE REGULATIONS Both Canada and the USA have had some form of laws governing the operation of mines since the late 1890s. The paths of legislation have run in reasonably parallel lines, continually improving the health and safety conditions in the mining industry. Ontario Mine Health and Safety In the 1970s the accident rates in mining were higher than any other industrial sector; this prompted a Royal Commission on the Health and Safety of Workers in Mines (the Ham Report). The recommendations of this report, published in 1976, generated several changes in the regulations regarding worker safety in mines. Following the release of the Ham report, the Occupational Health and Safety Act (OHS) was passed by the Legislature in 1978. The Act is a set of comprehensive laws governing almost all Ontario workplaces, and it replaced separate laws governing different industrial sectors. OHS is enforced by the Ministry of Labour (MOL), and this discussion will focus specifically on Ontario’s Occupational Health and Safety Act, R.R.O. 1990, Regulation 854, Mines and Mining Plants, Part X Mine Hoisting Plant (Ontario Regulations). USA Mine Health and Safety A coal mine explosion in West Virginia and medical studies on occupational disease led to the 1969 Federal Coal Mine Health and Safety Act (Coal Act). The Coal Act was the most comprehensive and stringent Federal legislation governing the mining industry to date. The Mining Enforcement and Safety Administration (MESA) was formed, following the 1973 Act, as a new departmental agency to assume the enforcement of safety and health in mines. The Federal Mine Safety and Health Act of 1977 (Mine Act) transferred enforcement responsibilities from the Department of the Interior to the Department of Labor and named the new agency the Mine Safety and Health Administration (MSHA). This agency enforces the Code of Federal Regulations (CFR), and this discussion refers to CFR Title 30 Mineral Resources, Chapter I Mine Safety and Health Administration, Department of Labor, Subchapter K—Metal and Non-metal Mine Safety and Health (MSHA)."

Jan 1, 2019

By A. Pearson, F. A. Auld, S. O. Colbeck

"""The theory of buckling of shafts and Steel tunnel-linings"" was published by E. Amstutz in 1970 and commented on by S. Jacobsen in 1974. The authors have revised and enhanced Amstutz’s work to address Jacobsen's comments on its limitations and to extend its validity over a wider range of pipe/shaft geometries, including those commonly found in deep mine access shafts. The author has looked at Amstutz’s assessment of strengthening with flexible shear anchorages and adapted the theory of non-linear shear deformation response of bolts to develop a method of assessing increased buckling capacity utilising the full plastic shear capacity of studs. INTRODUCTION “Amstutz Buckling” refers to the buckling of pipe embedded in concrete under external uniform pressure. In terms of a mining environment, this relates directly to the design of a watertight shaft. This load case will commonly occur where a main shaft is cast against a geostatically stable primary liner and the only load applied to the final shaft is that of a uniform ground water load. Ernst Amstutz wrote his first paper on buckling of pressure-shaft steel linings in 1950 and subsequently improved his theory (Amstutz, 1970), which was then widely adopted for use within the industry. Years later, an alternative approach (Jacobsen, 1974) was proposed. Within his paper Jacobsen critiques Amstutz work, identifying some mathematical inconsistencies and highlighting limitations of the theory imposed by approximations adopted by Amstutz. Despite these limitations Amstutz work has still been used as the favoured design theory for use in the mining industry. In reviewing this body of work the author realised that with the advent of readily available computing software it was possible to adopt an iterative approach using Amstutz approximate formulae to find a solution to the original precise formulae, thus eliminating the limitations highlighted by Jacobsen The shear deformation to load characteristics of bolts has long been established (Crawford & Kulak 1968) and used for the plastic design of bolted connections in shear. This relationship is directly transferable to the design of shear studs, typical properties are well known, and actual values easily established in simple lab tests. The author has taken this relationship and modified Amstutz theory (Amstutz, 1970) for shear anchored strengthened liner buckling, to give a more efficient solution, using readily available material properties."

Jan 1, 2019

By D. C. Downing

"I THANK YOU for the invitation which The Mining Society of Nova Scotia extended, originally to Gordon Berry, manager 'of our Point Tupper Refinery, to join you at this meeting and discuss refining and petrochemicals in their relation to this region. There are natural advantages in Nova Scotia which have made possible, and will continue to make possible, sizeable developments both in petroleum refining and in chemicals. Equally, however, as is the case everywhere, there are certain constraints. For clarity in this presentation, I will state some of these constraints right at the beginning. First, of any future developments from now on, only a small proportion of the products can be expected to go into local markets. I can make the point best with a few figures. Petroleum companies all have market forecasts. None ever work out to be perfect, but the trends are relatively predictable and the orders of magnitude are certainly correct. Estimates for the use of all refined petroleum products in the four Atlantic provinces are:"

Jan 1, 1973