Search Documents

By T. Feldmann, G. P. Demopoulos

The feasibility of chloride leaching processes depends on interfacing them with cost-effective HCl regeneration technologies. This paper summarizes the most important findings of research conducted in the past 3 years concerned with a novel process to regenerate high-strength HCl from concentrated CaCl2 solutions at temperatures below 100°C, via reaction of CaCl2 with H2SO4 resulting in the formation of calcium sulfate phases (gypsum, a-hemihydrate or anhydrite). From constant supersaturation semi-batch experiments in pure solution it was found that the crystal growth rate of hemihydrate, and hence the particle size, was influenced by the rate of reagent (Ca2+, SO4 2-) supply to the reactor. Additionally, growth studies of DH in presence of impurities (K+, Mg2+, Sr2+, Ba2+, Fe2+/3+, Al3+, La3+, Y3+, F- and PO4 3-) showed that specifically Sr2+ and PO4 3- are taken up during crystal growth. Furthermore, it was found that decreasing water activity (via different HCl/CaCl2 concentrations) and increasing temperature reduce the metastable life-time of DH and HH by increasing the phase transformation speed. The DH/HH transformation was identified to be dissolution-precipitation based, while HH to AH is a topochemical process. Finally, continuous experiments on bench scale are underway to confirm the feasibility of the process to obtain super-azeotropic strength HCl with up to 9 mol/L (~30wt.%) from 5 mol/L CaCl2 (~40wt.%) solution.

Jan 1, 2014

By M. D. Griffith

"Ventilation models are a vital tool to ensure ventilation designs can provide airflow to all work areas in a mine. Airway resistance and variations in natural ventilation pressures will affect simulated airflow and heat distribution through a mine. Validating ventilation model resistances and pressures to the exact underground conditions can be difficult and the variances can contribute to significantly different simulation results depending on the structure of the ventilation design. The study will use sensitivity analysis to explore examples of variability of simulated airflow due to small resistance, heat and natural ventilation changes and thereby help the user identify both trustworthy and potentially unreliable parts of a mine ventilation model. INTRODUCTION Mine ventilation network modeling is a vital tool for ventilation professionals and has become increasingly relied upon during the design and operation phase of mine ventilation systems. However, they provide only an approximation of reality, and caution must always be exercised when drawing conclusions or making decisions based on simulated data. Ventilation modelling should be performed by persons with a sound fundamental knowledge of ventilation and ideally should be validated with field data, but in large mines, or mines which are yet to be mined, accurate input of the simulation variables can be difficult, and errors and inaccuracies may be difficult or impossible to avoid. This study discusses and investigates the sensitivity of the mine ventilation simulation results to input errors. In addition, there are limitations to what steady-state airflow and heat simulations can model, regardless of the accuracy of the model inputs. In some situations, steady-state solvers cannot capture the dynamic changing behavior of a ventilation system. This study will also describe and apply techniques to analyze the natural variability of mine conditions on ventilation models. The consequences of poor accuracy in some parts of a mine model may impact on the health and safety criteria of ventilation designs. For example, if an airway is required to flow in a particular direction and quantity, then despite a ventilation model showing correctly designed conditions, small errors in input values may result in incorrect prediction of the direction or quantity of airflow. This may create unexpected buildup of heat or gases during operational activities, causing safety issues or operational delays. The ability to know which parts of a mine ventilation model have increased potential for poor simulation results will allow engineers to consider the ventilation design and make changes if required to better guarantee the required design flows."

Jan 1, 2019

By Maurice Séguin

The primary aim of all ground geophysical work has been, of course, to locate orebodies. As with any geo-physical method, its success depends on a proper mastering of the types of surveys and equipment used and their application to the physical properties associated with the orebodies. The Schefferville deposits are iron ores subjected to enrichment by the process of leaching. Although some ore types are porous and low in demiity, most of the ore zones have had a net increase in density brought about by enrichment. In the course of their formation, the magnetic characteristics of the rocks have usually changed, as much of the magnetite was altered to relatively non-magnetic iron oxides and hydrous iron oxides. Ali drift-covered areas underlain with iron-formation are potential ore-producing areas. From these first two physical proper-ties and a determination of the thickness of the over-burden, a combined gravity-magnetic-seismic and/or resistivity survey allows for the detection and sorting out of iron-formation and potential ore zones from the country rocks. If the iron-formation possessed relatively uniform physical and chemical properties, the problem of locating areas underlain with ore, using geophysical methods, would be greatly simplified. Unfortunately, the iron-formation is a complex assemblage of rock types, each having different physical and chemical characteristics. In spite of this, qualitative and semi-quantitative correlation between the results of the surveys and the geology and structure of the area could be established. In addition, a semi-quantitative to quantitative correlation of the values of the residual gravity anomalies with the specific gravity, the iron content, the porosity factor, the dimensions of the under-lying orebodies and the values of the ground magnetic intensity above a reference lithologie unit, with the per cent weight Fe304 recovery and the susceptibility, led to the discovery of a direct-shipping iron ore deposit in the Schefferville mining district of Canada.

Jan 1, 1968

By J. M. Livingstone

"This paper covers some of the problems confronted by Canada's railways in moving bulk materials from their source to the dock-site. The ""cost center"" concept is presented, and hypothetical examples of its use given. Also discussed are systems design, the unit train and pipelines.INTRODUCTIONCANADA LIVES BY RER EXPORTS and the Port of Vancouver by the exports of the Mountain and Prairie Empire at her back. The most recent estimates of off-shore shipments of bulk from the Port of Vancouver rise to 35.8 million shipping tons in 1985 and deep-sea general cargo estimates, in and out, are estimated at 7.6 million shipping tons for the same year. This compares to 7.67 and 2.87 million shipping tons, respectively, in 1965."

Jan 1, 1968

By K. Soldenhoff, M. Fainerman-Melnikova

The use of strong base resins for uranium recovery is severely affected by the presence of chloride ions in solution. In areas where high-quality process water is not readily available, the use of saline water would extend the potential application for ion exchange in uranium processing. This study presents measurements of uranium uptake, using a wide range of commercially available weak base anionic exchangers, from solutions with chloride concentrations ranging from 2.5 to 22 g/L Cl. Out of 14 weak base anionic resins tested, 3 were identified that were not severely impacted by the presence of chloride and significantly outperformed a gel strong base resin typically used for uranium recovery in high-chloride environments. The uranium loading was sufficiently high for the consideration of development of the application of uranium recovery from uranium ores leached with seawater.

Jan 1, 2012

By M. Zamalloa, P. J. Mackey, P. Coursol, Y. Prévost

"Over the last decade or so, the availability of commercial thermodynamic modelling packages, such as FactSageTM, have been utilized to help the plant optimize slag chemistry and to minimize slag handling issues that can arise, such as those due to a process upset, for example, by undue feed variability. This paper illustrates an extension of the application of this software in examining a large range of NCV operating parameters, such as the %Fe/SiO2 ratio in the slag and the level of minor gangue components in the slag including CaO, Al2O3, ZnO, MgO, and PbO. The conditions influencing the slag liquidus range of NCV slag are discussed with respect to the overall process chemistry.Given that a sufficiently low %Fe/SiO2 ratio is used in NCV slag, most components such as CaO-ZnOPbO- Al2O3-MgO, in small concentration, all contribute to lowering the NCV slag liquidus. Considering the present level of these minor components, the NCV can operate consistently at 1200°C if the %Fe/SiO2 is between 0.6 and 0.8 in the slag. Using the type of phase diagrams presented in this paper, it is possible to develop different Noranda reactor/Noranda converter operating strategies adapted to the feedstocks available at Xstrata mines/plants or from other sources. The NCV is unique in that a fayalite-based slag is employed for high-efficiency continuous converting with excellent operating results."

Jan 1, 2007

By H. T. Kennedy, D. L. Flock

"The project described in this pa-per was undertaken to provide a more thorough understanding of the effect of contamination by drilling fluids on the electrical properties of porous systems. The basic work per-formed was filtration tests on both consolidated and unconsolidated sands and the determination of their resistivity profiles with the aid of screen-type electrodes spaced at convenient intervals along the core.Four drilling fluids were selected, ranging in resistivity from 447.0 ohm-cm. to •5.76 ohm-cm. The permeability of three unconsolidated and four consolidated cores, on which resistivity measurements were made, varied from 1,257 md. to 4,560 md. Five additional cores with permeabilities as low as 49 md. were tested to investigate the effect of permeability on the depth of invasion of drilling fluids.The effect of drilling fluid invasion on resistivity profiles was determined on cores containing brine only, and on those containing 80 to 90 per cent oil and 20 to 10 per cent brine. The study included measurements of (a) clay content of different sections of the core, (b) saturation of the invaded fluids and oil in different parts of the core, and ( c) changes in resistivity as a result of gravitational re-distribution of fluids and diffusion of electrolytes.The data showed that the resistivity of an invaded core is, as was expected, controlled by the resistivity of the filtrate, the resistivity of residual core water, the resistivity of the clay particles, and the amount and distribution of the filtrate, clays, residual oil, and brine. In most cases there was a significant increase in resistivity owing to the presence of clay solids which had invaded the core. The change in resistivity, as a result of the diffusion of salts, was substantial after a period of five hours. There is evidence in some cases that the residual oil and core water saturations of the unconsolidated cores, after substantial invasion, are very low, indicating almost complete displacement by invading fluid."

Jan 1, 1959

By F. Ford, Z. Dai, A. W. Lee

ABSTRACT: As high-grade nickel sulphide ores are being depleted and processing laterite ores continues to pose challenges, the future of nickel extraction lies in low-grade ultramafic ores. Canada has large resources of low-grade ultramafic nickel sulphide ores in the Thompson Nickel Belt. Most of the deposits are high tonnage and open pittable, but have high MgO content. The main challenge in processing low-grade ultramafic ores is the presence of serpentine. Chrysotile, one of the three polymorphs of serpentine, is the most common form of asbestos. In addition, the high slurry viscosity associated with ultramafic ores makes grinding and flotation possible only at a very low solids percentage.

Jan 1, 2011

By R. Carter, C. S. Samis

"SummaryThe results of this investigation indicate that the gold in the cyanide tailing of refractory gold cyanides is occluded in fused •particles formed during roasting. This conclusion was reached following microscopic examination of calcines produced at various furnace temperatures with different atmospheres, and a •comparison with calcines produced by decomposing samples of completely sulphated concentrate under conditions such that the maximum particle temperature varied between 6•50°C. and 1,100°C. This comparison showed that the particle temperature during a normal roast may be several hundred degrees higher than the furnace atmosphere, or that the fusion is associated with a low melting (950°C.) eutectic mixture of FeO and FeS.Because of the unavoidable particle fusion during a furnace roast, and because low particle temperatures are essential for gold extraction by cyanidation, aqueous medium oxidation under high oxygen pressures was studied. Gold recovery from calcines produced by this means was over 98 •per cent •compared with a maximum of 80 per cent from furnace calcines.IntroductionMANY arsenical gold ores are called 'refractory' because much ' of the gold cannot be satisfactorily extracted by cyaniding the raw ore or concentrate. Even when such ores are roasted to oxidize .the iron and arsenic and 'release' the gold, often 10 to 25 per cent of the gold present is lost in the cyanide residues."

Jan 1, 1952

By J. T. Liu, G. H. Han, W. C. Chai, Y. F. Huang

"In beneficiation process, metal ions could adsorb onto clay mineral surfaces or interact with flotation chemicals, and then result in the flotation behavior changing of desired minerals. Al(III) is the dominating ion existing in the bauxite flotation system. In this research, the adsorption behaviors of Al(III) on two silicate clay minerals (including bentonite and kaolin) were investigated by means of UV-Vis spectra, zeta potential testing and scanning electron micrograph analysis. The adsorption experiment results show that the adsorption capacity of clays for Al(III) ions increases with the initial Al(III) concentration, contact time and solution pH. There are some different adsorption behaviours for two clays. Increasing the clay concentration decreases the adsorption capacity of bentonite, while increases first then decreases for kaolin. Higher temperature favours the adsorption of Al(III) on bentonite but goes against for kaolin. The adsorption capacities of bentonite and kaolin for Al(III) respectively reach 12.48 and 0.875 mg/g at initial solution pH 5. Zeta potential results show that the adsorption of Al(III) on two clays is characterized by electrostatic attraction mechanism.INTRODUCTIONIn beneficiation process, there is inevitably a wide variety of metal ions generated from mineral crushing, mineral dissolution and water chemistry conditions. Metal ions adsorb on the mineral surfaces or interact with the beneficiation agents, affecting the flotation efficiency of desired minerals (DiFeo et al., 2001; Parolis et al., 2008; Shackleton et al., 2012; Shengo et al., 2014). Therefore, it is necessary to have a detailed investigation on the adsorption behaviour of metal ions on clay minerals.Having good ion exchange capacity and negative surface charge, the clay minerals could take up various metal ions from the mineral-water system. Bentonite and kaolin are very common aluminosilicate clays in the mineral processing system. These two clays both hold a permanent negative charge, =X- on the basal surfaces, and a smaller variable charge, =SiOH on the mineral edges (Gu & Evans, 2008; (Gu et al., 2010). Adsorption experiments are usually used to study the adsorption affinity of metal ions for clay minerals (Sen & Bhattacharyya, 2012). The adsorption of Zn(II), Cu(II) and Pb(II) onto natural bentonite showed that the adsorption amounts of metal ions increase with contact time, solution pH and metal ion concentration, but decreases with adsorbent concentration and system temperature (Sen & Gomez, 2011; Melichova & Hromada, 2013). Cr(III) adsorption on bentonite was significantly pH dependent. The adsorption process followed pseudo-second-order model and the equilibrium adsorption was consistent with Freundlich isotherm (Lollino et al., 2015). The adsorption behaviours of Pb(II), Cd(II), Ni(II) and Cu(II) onto kaolin indicated that increasing pH favoured the adsorption of metal ions (Jiang et al., 2010). The adsorption of Cd(II), Cu(II), Pb(II) and Zn(II) onto kaolin showed that an ion-exchange reaction occurred at pH<7.0 and inner-sphere surface complexes were prone to form at higher pH (Srivastava et al., 2005)."

Jan 1, 2016

By R. W. Bruce, K. W. Downes

"IntroductionSULPHUR production in Canada from all sources for the year 1953 amounted to about 375,000 tons. Except for 16,000 tons of elemental sulphur derived from natural gas, this production was in the form of by-product pyrites, liquid sulphur dioxide, and sulphuric acid. In the same year, Canadian industry imported 359,000 tons of elemental sulphur from the United States. The cost, including transportation charges, to Canadian consuming plants ranged from $35.00 to $45.00 per long ton, depending upon location.Although most of the sulphur consumed is used in the oxidized form it is often most convenient to buy sulphur in the elemental form, and convert it to sulphur dioxide or sulphuric acid in situ as required. This is because elemental sulphur is easily shipped and stored, weighs only half as much as an equivalent quantity of sulphur dioxide and one-third as much as the corresponding quantity of sulphuric acid, and is readily converted to these forms in a sulphur burner. A process, therefore, which could economically recover elemental sulphur from sulphide ores would be most attractive.Since the turn of the century, notable improvements have been made in extractive metallurgy, but until recently only limited attention has been paid to the possibilities of elemental sulphur recovery. This has been due to the plentiful supplies of cheaply mined Frasch sulphur which have been available on the world markets."

Jan 1, 1955

By H. P. Whaley

This paper introduces Wabush Mines, including its ownership, physical assets, capacity, goals and achievements. It is to be followed by four papers which will present the detailed story. Wabush Mines, the largest supplier of iron ore to the Canadian steel industry, was brought into production in 1965. The ore is mined and concentrated in Wabush, Labrador, Newfoundland and pelletized at Pte. Noire, Quebec. Annual capacity is over 6,000,000 tons of high-grade iron ore pellets.

Jan 1, 1969

By D. Jean Hutchinson, Mark Diederichs

"Cable bolts are an important support component in modern underground mines. If an optimized cable bolt system is to be achieved, it is insufficient to focus on cable bolt layout design or on cable bolt installation in isolation. Cable bolt support, like all engineered systems, requires a holistic approach, encompassing integrated elements of design, implementation and verification. The “Cable bolting Cycle” described in this paper incorporates these components along with related tools and procedures which should be used together to ensure effective and efficient cable bolt support.Design involves the consideration of demand, capacity and constraints as outlined in this paper. The demands imposed on the sup-port system by the rock mass response to excavation under the combined action of stress and gravity must be matched to the capacity of the cable bolt array. The cable bolt system capacity is a function of the component strengths of the steel strand and the bond (load transfer) and by the deformation response and retention characteristics of the system. The design is bounded by operational and economic constraints.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.Implementation of the cable bolt array can then proceed and must include appropriate protocols of communication, training and quality control, in addition to both general and site specific installation procedures. Implementation will be discussed as the sum of these components.The information presented in this paper represents a very abbreviated version of much broader concepts, procedures and design charts, presented in a practical cable bolting handbook by Hutchinson and Diederichs (1996)."

Jan 1, 1996

By H. H. Gardner

INTRODUCTION THE problem of mechanization is one of the most vital in the minds of Alberta coal operators today. In these times of constantly increasing operating costs, any way of decreasing the cost of a ton of coal must be explored to the limit. There seems no better field for such effort than the successful application of power to the mining and loading of coal. We are fortunate in having neighbours to the south who have made .remarkable progress in recent times along these lines. Higher tonnages per man have resulted in higher wages to the employee and lower cost to the employer. It might seem that our problems could be solved merely by imitating our neighbours. Unfortunately, neither practice nor experience substantiate this conclusion. It is with the purpose of reviewing our accomplishments, as compared with practice in the United States, and at the request of the Prgoramme Committee for this meeting, that this paper is written. The Committee believes that such a general discussion and comparison may well lead to further advances in our mining methods. SUMMARY OF PRACTICE IN THE UNITED STATES A visit to the highly mechanized coal mines of the United States is always most instructive and encouraging.

Jan 1, 1951

By M. Jahazi, J. Gholipour

Design and manufacturing of parts using hydroforming process require knowledge about material behaviour and tribological effects during hydroforming. Lubrication is one of the key issues in successfully hydroform the tubes. A Ni-based super alloy tube with 50.8 mm (2 inches) outer diameter and 0.9 mm (0.035 inches) thickness is considered for this research to study the effect of lubricants on the formability of the tubes. Hydroforming of a hollow compressor blade is considered for this project. A combination of press forming and hydroforming is employed to produce the part. LS-DYNA, an explicit dynamic finite element code, is used to model the experiments. Different lubricants are modeled using different coefficient of friction in the model. Predicted results for strain distribution at a critical section of the tube are extracted for each case to evaluate the effect of different lubricants on the process.

Jan 1, 2006

By Glenn Davis

In the world of large scale open pit mining, the majority of a mines operating cost is tied to the removal and transportation of the overburden waste material. Typically, many large haul trucks are employed to transport this overburden from each excavating face. The trucks transfer the waste material from deep within the pit to waste dumps on the surface incurring significant costs in operators, road construction and maintenance, vehicle maintenance staff and support facilities, fuel, tires, and spare parts, as well as the capital cost of the truck fleet itself. In addition, the haulage of the actual mined material carries similar operational costs. In both cases, these costs grow as the mine face advances and pit haulage distances increase. Reducing truck haulage is one key to the success of the Dual Truck Mobile Sizer (DTMS). Being the world?s first fully mobile truck dump station, transportation costs can be significantly reduced as the mine face advances. Furthermore, when used in conjunction with a shiftable face conveyor and a mobile overland hopper, substantial cost savings can be achieved. The mobility of the system allows for the considerable reduction in the haul truck fleet. Overall mine site emissions levels are greatly reduced by the fleet elimination, as well as keeping the majority of the hauls on a flat grade within the pit. Emission levels on a typical truck will dramatically spike as the angle and the length of the haul are increased. Moreover, comparing diesel engines versus electric powered conveyors to move the material contributes to the realized savings.

May 1, 2010

By H. A. Hamza, J. Visman

"This is a report on the combined application of ""long-chain"" flocculants and classifier cyclones in the field of slimes treatment, with emphasis on the simultaneous thickening and clarifying of industrial effluents, at low cost. The principle of the process described below involves: (1) the formation of small floes of relatively great strength, by sequential dispersion and conditioning, with average floe size of about 1501 microns; (2) the floes being of sufficient strength to withstand the shearing forces operating within a cyclone and consequently behaving as solid particles with an equivalent diameter (Stokes) that exceeds the size cutpoint of the classifier cyclone; (3) the removal of flocculated solids by means of a classifier cyclone the size cutpoint of which permits effective separation of these solids from the water. Results of test work to date indicate that a broader use of cyclones in industry is possible with the above types of flocculants because the submicron particles and colloidal material are readily collected and clear water is produced, with the attendant advantages of compact construction and low cost that are characteristic of centrifugal separation. The process generally permits classifier cyclones of medium throughput capacity (e.g. 12-in. diam.) to be used for clarifying effluents that contain minus 10-micron particles."

Jan 1, 1973

By J. E. Dutrizac, J. B. Sunstrum

Until relatively recent times, virtually all gold was recovered by gravity and/ or amalgamation methods. Although such techniques are very effective on coarse gold, they become increasingly less useful for finer grains especially when the gold is partly enclosed in rock matrix. Throughout the nineteenth century a number of bonanza gold fields were found in the United States, South Africa, Australia and Canada. In every case the abundant supply of gold nuggets and coarse alluvial gold soon gave way to hard rock mining with its inevitable losses of fine gold in the stamp mill tailings. Continuing efforts to develop new technologies capable of dissolving gold from finely ground ore were eventually successful first with chlorination (the Plattner process) and subsequently with cyanidation. Even before the nineteenth century, however, European chemists such as Scheele and Berthollet were aware that gold could be readily dissolved in an excess of free cyanide(1). As early as 1840, a patent was issued to the Elkington brothers for the dissolution of pure gold in cyanide solution and its subsequent plating onto various metals, with or without an applied electrical current. In 1846, Elsner showed that oxygen was also required to solubilize gold or silver in cyanide media(1). Despite the fact that much work was done on the reaction of cyanide solutions with gold, a viable leaching process for gold ores did not quickly emerge although cyanide solutions were used to enhance amalgamation from the 1860s onward. Major problems were associated with the use of concentrated cyanide solutions; the costs of cyanide were excessive and it was difficult to recover gold from the concentrated media.

Jan 1, 1999

By J. R. Giegerich

THE problem of dust control in metal mines has, of late years, received considerable attention. In 1932, a detailed study of dust conditions at the Sullivan mine was undertaken and, while there are no actual data available regarding conditions prior to that date, there has unquestionably been a great improvement as a result of the investigation and of the preventive methods adopted. In attacking the problem, three main factors were considered: first, and most important, how to prevent dust from being formed; second, how to depress or collect it if formed; and third-if unable to accomplish these-what precautionary measures must be adopted to prevent inhalation of this dust. Seven distinct methods of dust control are now practised at the Sullivan. Six of these are employed underground; they are tabulated below in the order of their relative importance. The seventh method is used in the crushing plants on the surface. (1) Improved ventilation (2) General use of water sprays and atomizers (3) Curtailment of secondary blasting during shift hours ( 4) 100 percent wet drilling-primary and secondary (5) Wearing of protective equipment (6) Change from carbide to electric lamps (7) Installation of dust collectors

Jan 1, 1936

By E. Barnard, J. Tero, J. Rajala, N. Avenido, M. Fullam, A. Nashitati, S. Mbalamba

"The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum, with an average reserve gold grade of 1.28 g/t. The ore is high in Gravity Recoverable Gold (GRG), which varies between 73-91%, depending on ore type. Overall gold recovery since start-up is 98.2%, with about 63.5 % coming from the gravity circuit as doré. 2016 cash operating costs, and all in sustaining cost (“AISC”) were $361 and $604 per ounce, respectively.During design, three ore types were tested for GRG content, and based on the high GRG value of all three ore types, the decision was made to treat the full ball mill circulating load by gravity. Once operating, the gravity circuit performance was characterized by performing a detailed gravity audit, which included the ore, cyclone classification, Knelson concentrators, and the Consep Acacia intensive leach system. The deeper ores contain significant pyrrhotite, and this created some unusual challenges that had to be overcome. This paper presents the gravity circuit design process, the circuit commissioning, and the audit results and ongoing improvements.IntroductionHeadquartered in Vancouver, Canada, B2Gold Corp. was founded in 2007. Currently, B2Gold has five operating mines, and numerous exploration projects in various countries, including Nicaragua, the Philippines, Namibia, Mali and Burkina Faso. The Otjikoto Mine is located in the north-central part of the Republic of Namibia. It is situated approximately 300 kilometers north of Windhoek, the country’s capital, within the Province of Otjozondjupa. The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum. During design, a large emphasis was placed on gravity recovery, as the Otjikoto ores are unusually high in Gravity Recoverable Gold (GRG)."

Jan 1, 2018