Search Documents

By Vladislava A. Ignatkina, Fillip O. Milovich, Vladimir A. Bocharov

"Complex research of flotation concentrates of monomineral fractions of chalcopyrite, sphalerite, galena, pyrite, pyrrhotite included methods of adsorption of collectors, surface compounds by IR ATR, and surface films of flotoreagents by TEM. They revealed that the proportion of the parts of thionocarbamate (TC) and dithiophosphate had an effect on the adsorption rate of the components of minerals, on the presence of characteristic bands, and, what is an important, visualized surface film of organic flotation reagents on the particles of concentrates by TEM. The predominance of thionocarbamate in a composition selectively increases the adsorption rate constant of the components and recovery of chalcopyrite compared with sphalerite and galena. The highest flotation rate using TC is characteristic for chalcopyrite (0.62 min- 1) in case of individual use, and it's in combination with butyl xanthate (25% butyl xanthate or 3:1) 0.89 min-1 too. We studied the ternary blend - dithiophosphate: thionocarbamates: butyl xanthate. The increase of the proportion of butyl xanthate in combination reduces the contrast of the flotation rate among all sulfides.Practice flotation of refractory sulfide copper-zinc ores of the Urals (content sulfide iron - 75- 95%) confirmed that the use of a combination of selective collectors increases selective recovery of copper sulfide minerals up to 50% at the first fraction that is the conditioned copper concentrate. New selective sulfhydryl collectors resulted in high levels of recovery of copper into a concentrate - more than 90% - against 70-72% (butyl xanthate) from copper-pyrite ore. Low floatability of iron sulfides has been obtained by selective sulfhydryl collectors. Using weak selective sulfhydryl collectors can reduce pH into collective or selective flotation from pH 10-10.5 to pH = 7.2-7.5, which improves the quality of individual concentrates of nonferrous metals and their recovery. The same is true for polymetalic sulfide ore. The volume of gold recovery also increased."

Jan 1, 2016

By M. Kim, M. Ha

"The effect of red mud on the melting behavior of ferronickel slag was investigated by a laboratory-scale horizontal tube furnace. Melting and softening of slag samples fluxed with different amount of red mud was examined by in-situ visualization technique at temperature range from 1400 to 1550°C. FactSageTM 7.0 was used for the thermodynamic calculation of multi component system of ferronickel slag and red mud. Liquid phase area was extended to lower temperature by adding red mud indicating its suitability as a flux material. X-ray diffraction analysis confirmed the dependency of the phase changes on the red mud content. Microscopic observation by scanning electron microscope (SEM / EDX) clarified the phase transformations from olivine to spinel along with red mud additions.INTRODUCTION Ferronickel smelting by submerged arc furnace (SAF) is an energy intensive process performed at high temperature range 1500–1600°C. During the smelting process of saprolitic nickel laterite ore with a nickel content of 2.2–2.3 pct, a large quantity of ferronickel slag is being produced that account for 97 pct of ore charged. To achieve ferronickel grade of 15–20 pct Ni, electrical energy of 80 to 85 MW is used for the melting and reduction of nickel oxide (NiO) and iron oxide (FeO) in the ore (Rodd et al., 2010). Unreduced components, mostly MgO, SiO2 and partly FeO are removed from the furnace in a liquid slag form by a tapping operation. Due to the high melting temperature, forsterite (Mg2SiO4) based slag containing approximately 10 pct FeO requires typical process temperature of 1600°C. Flux in metallurgical process is a medium that decreases melting and operating temperatures while it increases fluidity of the liquid slags. Calcite and fluorite are examples of flux materials used for the ironmaking, steel refining and continuous casting process. Oxide systems based on CaO - CaF2 - SiO2 - Al2O3 - MgO cover most of the slag composition in ferrous metallurgy accordingly. Crucial operating factors for ironmaking and steelmaking slags are basicity (typically CaO/SiO2 ratio), viscosity and impurity levels. These are extensively controlled by the fluxes. General metallurgical fluxes such as limestone, dolomite and calcium fluoride are abundant in nature and supplied to steel mills at low prices. Meanwhile, in copper flash smelting process, silica is supplied with copper concentrate to remove iron oxide (FeO) generated from sulfide oxidation. FeO - SiO2 binary system formulates eutectic area at 25–38 pct of silica that has low melting temperature below 1205°C. Fayalitic system (Fe2SiO4) that has low viscosity (0.1 Pa·s) (Park et al., 2011) facilitates easy separation of slags from molten sulfide mattes. Recently, copper plants actively utilize recycled raw materials as a flux. Various recycled glasses are ground and fed to copper smelting process as a partial replacement of silica ore. Applying industrial wastes to smelting processes is advantageous since the operators can reduce the production cost remarkably. Not to mention the consumption of recycled materials can ultimately minimize the environmental risks and the waste management costs. The authors, therefore, investigated the reasonable waste materials that can be effectively used for ferronickel smelting process. Prerequisites for potential fluxing materials are non-recyclable property, low transportation cost and excellent performance as a flux."

Jan 1, 2017

By Charles Graham

It is the general belief that the coal deposits on Vancouver Island are extremely large, and easily available. Indeed, they are frequently described by prominent public men and by writers in the press as "illimitable" and "inexhaustible." It is well that the facts that have been established as a result of seventy years of surface prospecting, underground operations and extensive diamond-drilling in this coalfield should be disclosed. HISTORY The presence of coal on the coast of British Columbia was first made known by Dr. W. F. Tolmie in 183 5. This coal was brought to him by Indians from the north-east coast of Vancouver Island, probably from Suquash. In 1850 the existence of coal at Nanaimo was announced by Mr. ]. W. MacKay. Development was started in 1852, and coal was shipped before the close of 185 3. The first operations were carried on by the Hudson's Bay Company, who operated the mines until 1861, when they sold them to the Vancouver Coal Mining and Land Company. Practically all of the operations in the immediate vicinity of Nanaimo have been carried on by this Company and its successors. In 1869, Mr. Robert Dunsmuir discovered coal about five miles north-west of Nanaimo, at Wellington. The Welling-ton Colliery Company was organized, and began to produce coal from the Wellington mines in 1871, the coal being shipped from Departure bay. This colliery was a large producer for several years, but was finally closed in 1900.

Jan 1, 1924

By M. Dupuis, V. Bojarevics

It is well known that horizontal current density in the metal pad contributes greatly to the generation of MHD driven bath-metal interface wave. It is possible to compute very accurately the metal pad current density using a very detailed finite element model [1], but a MHD model must be compatible to this level of mesh refinement and to recalculate the current distribution at each time step, including the full busbar supply system. The accuracy of the instability prediction of the cell depends on the accuracy of the metal pad current density calculation. This study presents the comparison of the metal pad current density calculation of the detailed finite element model and the MHD-Valdis model for different metal pad heights and ledge thickness. It also presents the corresponding cell MHD stability predictions.

Jan 1, 2006

By G. J. Arseneau

Mineral resource statements are reported as tonnage and grades. While great care is placed on generating a reliable estimation of grade, the determination of bulk density for resource estimation is often overlooked. Often mineral resource statements are prepared using a simple average value of bulk density. While a simple average estimate of bulk density can be appropriate for some deposit types, an over simplistic estimation of bulk density can result in serious errors in tonnage estimates and consequently to an over or under estimation of metal content. The construction of a reliable bulk density model requires an adequate bulk density database in order to develop a good understanding of the variability of bulk density with grade and geology. A reliable bulk density database is also essential in determining the appropriate modeling technique to minimize the errors in mineral resource statements caused by incorrect bulk density determinations. This paper summarizes bulk density measuring techniques and draws on examples from various deposit types examining the basic principles of bulk density modeling and domain construction for each deposit type. Examples are presented of simple bulk density domains and more complex grade variable bulk density domains with a discussion of best approaches for minimizing errors in density estimation.

Aug 1, 2013

By A. Kapoor, L. Morin, S. Mortazavi, P. Béedard, Gould. W. D., A. Kuiper

The degradation of thiocyanate in a simulated gold mill effluent was studied using a laboratory scale rotating biological contactor (RBC). Complete SCN- removal was obtained at temperatures of 8 and 12°C, and a hydraulic retention time of approximately 3.3 h. The NH4+ produced by thiocyanate hydrolysis was oxidized by nitrifying bacteria to NO2 and NO3-. The HS- produced by thiocyanate hydrolysis was chemically and biologically oxidized to elemental S, which was subsequently biologically oxidized to sulfate. Incomplete sulfur oxidation occurred in the RBC, particularly at 8°C and elemental sulfur deposition was observed on the RBC disks. The RBC feed exhibited toxicity to rainbow trout but the RBC was effective in removing the acute toxicity of thiocyanate.

Jan 1, 2005

By E. A. Roux

As the first mine-to-metal zinc operation utilising atmospheric leaching, solvent extraction and electrowinning, Skorpion Zinc faces unique challenges and opportunities. One of these challenges is found in the solvent extraction circuit, in which di-ethylhexyl phosphoric acid (D2EHPA) is used as the organic extractant. Although D2EHPA is an excellent extractant for zinc, it suffers from the co-extraction of ferric iron, which is produced during leaching and by the corrosion of the grinding media. This situation is partially mitigated by iron precipitation in the neutralisation step prior to solvent extraction. Unfortunately, some ferric iron still reports to the solvent extraction process. This leads to a slow build up of iron in the organic phase. Chemical stripping is used to maintain the Fe concentration at an acceptable level. In this paper, the efficiency of the iron removal process is discussed.

Jan 1, 2006

By N. Valkanov

This paper presents results of an investigation into the connection between minerals liberation management and flotation, responding to lead-zinc concentrator ?Erma reka?, in Bulgaria. Monitoring of a Zn flotation circuit was carried out. The causes for the high silica content in the final Zn concentrate were established. Quartz is present mainly as liberated particles (> 60?80 %) in the fine fractions of the products; therefore the selectivity of the flotation process is not effective. Two approaches were tested to reduce the quartz content of Zn concentrate: froth washing in Zn cleaner flotation and new gangue depressants in the Zn circuit. Experimental results from bench-scale flotation and industrial tests show that it is possibile to reduce the silica content of final Zn concentrate more than 2 times without the need for extensive regrinding. The depression of liberated quartz particles on all operations of Zn circuit using stage depressant addition is the right solution to produce high-grade Zn concentrate that meets the metallurgical requirements.

Aug 1, 2013

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations in the smelting and refining of non-ferrous metals, and is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate and is the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y. Year after year the production has been increased, and at present, the production capacity is 240,000 t/y. In this paper, the leaching process,particularly the operation of the jarosite circuit is reviewed ,specifying process improvements to treat high iron calcines.INTRODUCTIONThe purpose of the leaching process is to recover the metals, mainly zinc,through a series of extraction stages with sulphuric acid solutions, which progressively increase the zinc recovery. After the series of acidification stages,the solution, which is rich in iron, is sent to the jarosite circuit to separate the zinc from the iron (Garcia & Valdez, 1996).The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper, after this solution is sent to the tankhouse to feed the electrolytic cells."

Jan 1, 2016

By T. Senga, T. Namihira, S. Terada, S. Owada

"Electrical disintegration (ED) has been well known as a good comminution method to improve liberation of compositional phases because it was reported that electron avalanche could occur preferentially at phase boundary. But the detailed mechanism of the ED has been still not known. This paper describes the results of ED experiments using synthetic binary sample, copper/resin, under the conditions of various distance between electrodes, and discusses the energy distribution in the three kinds of phenomena in the ED process, which are(1) streamer progression in water, (2) electron avalanche in water, and (3) electron avalanche in solid sample, by measuring current and voltage with elapsed time. Then, it has been found that the energy distribution in the phenomenon (1) is quite low and that the distribution in the phenomenon(2) had a considerably large compared with that in the(3), which indicates that the shockwave generated in water could contribute much to the sample breakage.INTRODUCTIONElectrical disintegration (ED) has been well known as a specific comminution technology which enhanced selective breakage at phase boundary and lead to a good liberation among compositional phases1-6),but the detailed mechanism has not been clarified yet. This study describes energy distribution among the phenomena in the ED process by using a synthetic binary sample, copper/resin, the phenomena of which are (1) streamer progression in water, (2) electron avalanche and shockwave generation in water and (3) electron avalanche in solid sample usually at phase boundary. The energy distribution could be calculated from ED experiments and from voltage-current changes between electrodes as a function of elapsed time.SAMPLE AND EXPERIMENTALSampleThe sample used in this paper was a synthetic binary solid of copper/resin as shown in Figure1.Cut and polished pure copper lump was put into silicone mold and melted epoxy resin was poured into it and cooled, then, finally the binary sample was polished and molded in the form of 10 mm * 10 mm * 10 mm."

Jan 1, 2017

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By T G. Callcott

Australian coking coals are either class 434<tlj534<2l, at Port Kembla, or 634<3> at Newcastle. The former yield good blast-furnace cokes; the latter yield poor ones. However, increases in conventional strength indices, by methods applicable with normal coking ovens, seem unlikely to be economically attractive. Characterization of the coals has enabled an "economic" blend to be developed in the Newcastle area, and this has affected mining, preparation and handling operations. Coking studies have led to a specification for the making of strong coke, especially from the high-volatile Newcastle coals. Continuous coking studies, developed from the efforts to make very strong coke, have taken two directions. Firstly, coking thin layers of coal on strands; secondly, coking, in various types of vessels, compacts of coals with or with-out the inclusion of non-coking coals, iron ores or other inert materials. Gas, "sand" and hot metal coking have been tested for use in compact coking. Particular attention has been paid to pellets of coal and ore. The probable industrial problems in adopting any of the ideas are presently being examined.

Jan 1, 1963

By T. W. Wong, M. A. Whitney, A. Hadadzadeh

Uniaxial compression tests were performed on cylindrical specimens, 10mm in diameter and 15mm in height, machined from an extruded AZ31B magnesium billet. The tests were conducted under isothermal conditions to a true strain of 0.5. The study compares macroscopic flow anisotropy between the extruded (ED) and transverse (TD) directions in the temperature range of 300°C to 500°C, and strain rate range of 0.001s-1 to 1s-1. Compression of ED specimens at low strain rate (0.001s-1) exhibited axisymmetric flow, and no significant differences were observed between geometries of specimens deformed above 350°C under the same strain rate. Deformation of TD specimens at low temperature and/or low strain rate resulted in elliptical cross-sections, with the anisotropy of flow being less significant at higher temperatures. Other studies performed using rolled plates have proposed that pyramidal slip and cross-slip at higher temperature eliminate the effects of initial texture, while the dominance of prismatic slip at lower temperatures will result in anisotropic flow. It is believed that the initial fiber texture common among extruded HCP-structured materials plays a role in the anisotropic deformation behaviour observed in the extruded specimens

Jan 1, 2015

By S. Esfahani, M. Barati

Heat recovery from blast furnace slags is often contradicted by another requirement, to generate amorphous slag for its use in cement production. As both the rate and extent of heat recovery and slag structure are determined by its cooling rate, a relation between the crystallization kinetics and the cooling conditions is highly desired. In this study, slags with different basicities were studied during non-isothermal cooling. Their continuous cooling transformation (CCT) diagram were plotted and compared with each other. Then, a mathematical model was developed that predicts the amount of crystallization during cooling. The results were validated by experiments performed by Single Hot Thermocouple Technique and image analysis. A second mathematical model that calculates temperature history of slag during its cooling was coupled with the above model, to allow optimizing the slag/air ratio for both heat recovery and slag glass content.

Jan 1, 2015

By Janice Zinck, Maziar E. Sauber

"To counter the recent uncertainty in the rare earths market, diversify the supply source, and help meet the future demand in this sector Canada initiated development of several new rare earth deposits. In the past few years, a number of various studies on rare earths plant design have taken place mainly covering process development, process selection, and flowsheet design. The purpose of this paper is to provide an overview of known domestic and potential resources and reserves of rare earths and their status quo with a focus on the metallurgical processes using the information available in the public domain. Plant designs currently under consideration in Canada are reviewed and evaluated. An outline of the areas of opportunity for selective innovation and technology development in the rare earths flowsheet development and the associated risks and rewards is provided.INTRODUCTIONThe rare earth elements (REE) have a very small annual market, but they are categorized as very strategic metals vital to global economic growth due to their indispensability to the development of modern defence system, green technologies and electronic applications. The International Union of Applied and Pure Chemistry (IUPAC) defines the REE as the 15 elements on the lanthanide series on periodic table of elements, plus yttrium and scandium. REE are classified as light rare earth elements (LREE; La to Gd), and heavy rare earth elements (HREE; Tb to Lu). Physical properties and chemical reactivity of yttrium is similar to those of HREE, thus it is categorized as such. Properties of scandium are not similar enough to classify it as either a LREE or HREE (Weng et al., 2015; Sappin & Beaudoin, 2015). However, the mining industry does not always abide to this definitive classification of the split between LREE and HREE. Therefore, in a comparative study of projects, there is a need to pay attention to how the elements are classified."

Jan 1, 2016

By F. M. Clement

British Columbia, unlike the Prairie Provinces, cannot lay claim to vast prairies. She can, however, claim many valleys, uplands and plateaus that are capable of marked agricultural development. It has been said that British Columbia is not an agricultural province. This may or may not be true, but at the present time agricultural production in this province stands second only to that of forestry. The industry has advanced from a total production of 8 millions in 1908 to a total production of 60 millions in 1924, a total increase of approximately 650 per cent in 16 years. In the last 10 years production has increased from 30 millions to 60 millions. No other industry can point to such a rapid development. In 1908 British Columbia imported 12 million dollars worth of foods compared to the 8 millions which were produced at home. In 1924 she imported 20 million dollars worth of foods compared to the 60 millions worth produced at home. In addition we exported foods to the value of approximately 10 million dollars. British Columbia is therefore self-sufficing in-so-far as values ar.e concerned except for approximately 10 millions of dollars. It is not to be expected that this province will ever grow all the coarse grains that she may require: these, along with certain meats, will always be a heavy item in the imports. We are concerned at the present time more with the value of the products than with the quantities produced: in other words, with quantities only in-so-far as ? quantities improve value.

Jan 1, 1925

By J. Scrimgeour

"The word ""instrumentation"" has expanded from its original meaning, which in engineering perhaps referred to measuring apparatus alone. In its broadest form, it now includes sensors, display instrumentation, standard pack-aged controllers and, most recently, the use of stored program computers for on-line process control. The paper traces the evolution, in tutorial form, of the successive application of mechanization, measurement instrumentation, automatic control, central operating systems, programmed control, process computer control, direct digital control and, finally, hierarchies of computers used for process control and corporate management as a fully integrated business system. In the field of industrial minerals, the cement industry has seen the most widespread acceptance of these techniques. Computer control has been accepted as the way of life for the blending of chemical materials and for on-line control of the cement kiln. Accordingly, the cement application is selected for further presentation in the paper. This illustrates the trend progressing from control of single loops on process variables toward the objective of total control of the product quality. The economic justification for instrumentation, centralized control, automatic control and computer control is .discussed with reference to savings in fuel, maintenance, operating labour, depreciation, power and product quality improvements."

Jan 1, 1967

By J. H. Pee, Y. J. Kim, H. U. Lee, G. H. Kim

The general recycling process of tungsten scrap to produce tungsten raw materials (tungstic acid, ammonium paratungstate (APT) and WO3) have been carried out by the oxidation, milling, sodium-fusion, dissolution, and extraction processes. Many studies on the high temperature oxidation of tungsten scrap have investigated various aspects such as swelling kinetics, fracture resistance, and the effect of alloying composition. However, the accelerating factors on the scrap oxidation rate during oxidation were not considered here. In general, oxidized products were fused with sodium carbonate or sodium hydroxide to produce Na2WO4. Later in the process, solid Na2WO4 was dissolved in water. This process required considerable reaction time and was a costly process. Therefore, the aim of this study was to increase the solubility of solid oxidized products to produce Na2WO4 solution by hydrothermal reflux method. Na2WO4 solution was used to produce CaWO4 and H2WO4 by general chemical reactions with calcium chloride and hydrochloric acid. Ammonia solution was also added to the tungstic acid to produce APT. In this study, the effect of ammonia addition on the APT precipitation process was investigated in detail.

Jan 1, 2015

By X. Zhou

"Hydrogen induced failure and degradation in structural metals, namely hydrogen embrittlement, has been a long-standing industrial problem for more than one century and remains unsolved. Despite the proposal of numerous models, no consensus has been reached, and considerable discrepancies in experimental observations and theoretical calculations exist. One aspect that is central to the understanding of hydrogen embrittlement is the interaction between hydrogen and grain boundaries. In this study, we investigated the influence of several solute elements (i.e., Cr, Mo and Nb) on hydrogen segregation at the representative 9 grain boundary using first-principles calculations. Our results showed that the presence of Mo and Nb can reduce the tendency of hydrogen segregation at grain boundaries, while meanwhile enhance the grain boundary strength. This indicates that Mo and Nb are salutary elements that can be used to increase the material’s resistance to hydrogen embrittlement, providing new insights in designing hydrogen embrittlement resistant Ni alloys. INTRODUCTION Hydrogen embrittlement (HE), a phenomenon of hydrogen triggering premature failures in structural metals, has been a headache for industries ever since its first discovery one century ago (Johnson, 1874; Zhou, Marchand, McDowell, Zhu, & Song, 2016; Zhou, Ouyang, Curtin, & Song, 2016). It is well accepted that the segregation of hydrogen at microstructures such as grain boundaries (GBs) plays a key role in determining the occurrence and severity of HE. GBs are two-dimensional defects where significant local lattice distortion exist, which leads to large free volume and thus locations for hydrogen trapping and segregation. Numerous works have clarified GBs as the energetically preferable places for hydrogen segregation. For instance, Geng et al. demonstrated the preferential segregation of hydrogen at the S5(120) GB in several metals, and suggested a decohesion-type of HE in light of Rice-Wang thermodynamic theory (Geng, Freeman, & Olson, 2001). Birnbaum et al. illustrated that complete intergranular crack of Ni GBs can be induced by hydrogen segregation when the hydrogen concentration is sufficiently high, evidencing the significant role of hydrogen accumulation on GB weakening (Lassila & Birnbaum, 1987). Yamaguchi et al. demonstrated strong segregation hydrogen also occurs at S3 GBs in alpha-iron, showing that local hydrogen clustering (i.e., multiple hydrogen atoms, up to six, per unit cell) can be trapped at the S3 GB (Yamaguchi, Kameda, Ebihara, Itakura, & Kaburaki, 2012)."

Jan 1, 2017

By Allan P. Fawley

ONE hundred miles from Vancouver, at an elevation of 4,000 feet, is the Pioneer mine. It is situated on Cadwallader creek, a tributary of Bridge river, and is reached by travelling from Vancouver to Squamish by boat, a distance of thirty-two miles, from there by train to Bridge River (one hundred and seven miles), and finally by automobile across Mission mountain .(7,000 ft. elevation) to the mine (fifty-six miles): a total distance of one hundred and ninety-five miles. Prior to 1924, many Companies had examined the Pioneer, which had been developed by shaft to a depth of 200 feet, but, while values were good, the small size of the ore-shoot discouraged large investors. In July, of that year, opera-tions were re-commenced by the late David Sloan and, on sinking further, the ore-shoot was found to lengthen greatly as well as to ex-tend in depth, while remarkable gold values also were encountered. When, later, the price of gold rose from $20 to $35 per ounce, the mine was in an excellent position to take full advantage of the increase + and not only became an extremely profitable enterprise itself but its success greatly stimulated the search for and development of other 1-gold properties in British Columbia.

Jan 1, 1937