Search Documents

By John C. Robbins

A new technique for the determination of trace levels of uranium in solution has been developed. A compact laser emits short, but intense, ultraviolet pulses to excite the green fluorescence of a uranyl-complex formed by the addition of a proprietary reagent to the sample. Organic species present in most natural waters also fluoresce quite intensely, but their emission does not last appreciably longer than the excitation pulse, in contrast to the relatively long persistence of the uranyl fluorescence . Electronic 'gating' is employed to separate the long-lived contribution, rejecting substantially the organic emission. Results using the laser fluorescence method on many sets of natural waters of various origins have been compared against corresponding values generated by independent laboratories. Correlation has been generally good over a range from less than 0.1 to more than 100 ppb U. Solid samples have also been analyzed after extraction of the uranium into solution. Accuracies adequate for most exploration purposes have been achieved, but further work is required to determine effects of interferences in samples with complex matrices. The transport and deposition of uranium in natural waters is controlled by the organic and inorganic chemistry of the waters involved. It is suggested that interpretation of very low uranium levels will be aided by additional measurements of conductivity and organic content, with subsequent statistical treatment.

Jan 1, 1978

By W. P. Campbell

In the course of the development of the Red Coulee field, northwest of Coutts, Alberta, a considerable amount of information has been gathered by the Department of the Interior regarding the chemical character of waters encountered in the drilling of wells in this area. The writer, in this paper, has undertaken to assemble the available material with the idea of deducing what relations, if any, may exist between the different waters from the same well, and also how these compare with waters encountered in similar horizons in other wells. From no other district, with which the Department of the Interior has had to do, have there been received so many samples of water, and yet not all the waters logged in the drilling reports were sent in for analysis. The information, therefore, herein contained is not as complete as the writer would have desired, but sufficient evidence has been accumulated to indicate some very definite tendencies in the chemical nature of the waters of this field. The drilling of Red Coulee wells has been carried out exclusively by percussive tools. These permit 'dry' drilling, and, consequently, water-sands are recognized when encountered. Had rotary tools been used, information regarding water-sands would have been very meagre, if not entirely lacking, since, in the mudding-off process, water-sands would have been overlooked, with the result that, should water break through into a completed well, its source would not be known and remedial efforts would be greatly handicapped, if not entirely defeated.

Jan 1, 1931

By R. K. Jonas

"Pressure leaching and pressure oxidation in autoclaves are important alternatives in the extractive processing of gold, copper and nickel ores. The application of advanced control to pressure leach and pressure oxidation autoclaves could achieve significant benefits as has been shown in alumina pressure leaching. This paper compares and contrasts alumina digestion autoclaves to other mining autoclaves with respect to advanced controls. The application of advanced control in alumina with over 30 units controlled worldwide, and its benefits will be reviewed. The design and potential benefits from advanced control for pressure oxidation and leaching will be presented.INTRODUCTIONIt is this author's position and the purpose of this paper to propose that advanced control could be effectively applied to autoclaves in the nickel, gold, and copper mining processes. This is based on the proven effectiveness of advanced control on autoclaves used in the alumina industry for pressure leaching of bauxite ores. Incremental, but significant increases in production could be realized by applying advanced control to autoclaves, as evidenced by the alumina industry, and this not being implemented in other autoclaves in the mining industry.In addition, today the mining industry is being challenged to improve their production methods. In some markets like nickel, there is pressure to improve productivity and reduce the cash cost per ton. While in other markets like copper and gold, demand is vigorous with favourable pricing, and there are advantages to increase production and productivity given limited plant capacity. Advanced control has proven its capability to improve mineral processing operations through increases in throughput, recovery, as well as reducing variability. In today's mines, autoclaves are being used to a much larger scale and with much larger importance, thus it would be beneficial to improve operational performance through the use of advanced control.Accordingly, it is the author supposition that an opportunity exists in the mining industry to use a proven advanced control technology to improve the operations and financial performance of mines using autoclaves."

Jan 1, 2012

By S. P. Lowe

Introduction In the following pages a general description is presented of the concentrator and cyanide plant of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, together with some account of the steps which have led to the adoption of the present practice. For an account of the preliminary test-work and pilot-mill operation, the reader is referred to a recent paper by R. E. Phelan on the History of Flin Flon Mine up to Construction (1). Additional notes may be found in a paper which the writer presented at the Annual Meeting of the Institute in 1930 (2). The first ore was crushed in the present plant on July 1st, 1930, and the first ball-mill was started one month later, on August 1st. Since that time, production has been continuous with the exception of one month lost during a strike in the summer of 1934. There have been no major changes in equipment or methods of treatment since the present plant was built, but many minor changes have contributed to the improvement in results obtained and to the increase in capacity to the large tonnage now being milled. The accompanying flow-sheets indicate the equipment used in the several plants, with the average life and repair cost. As originally built, the concentrator was to treat 3,000 tons per day, but the capacity has been increased to 4,400 tons. The methods adopted to make possible this increase in tonnage will be referred to below. It was the intention to produce two classes of ore: (1) a heavy sulphide, and (2) a disseminated ore. The mill was consequently divided into two sections, each adapted for most efficient treatment of one particular type of ore. However, it was soon found that it would be impossible to mine the two classes of ore separately, so it was decided to treat open-pit ore, which varies greatly in character, in the sulphide section, and underground ore, which is fairly constant, in the disseminated section. This segregation is still maintained.

Jan 1, 1935

By K. Trapani

"The study undertaken aims to investigate an ice stope heating and cooling system for its potential to be implemented in sub-arctic mines, as a low carbon alternative to conventional natural gas and refrigeration chiller systems. Its performance was simulated for a years’ worth of data, taking into consideration hourly temperature data. Results showed that to supply the required heating and cooling loads, the ice stope system had to supplement its heating with natural heating. The techno-economic performance of this system was compared to that of a conventional heating and cooling system in a mine, with the ice stope thermal storage system hawing the lowest annuitized cost and significantly lower carbon emissions.INTRODUCTIONConventional heating and cooling, in a mine is implemented using natural gas heaters and chiller refrigeration systems respectively. This results in a significant portion of energy consumption in underground mines attributable to ventilation (De Souza, 2015), including the conditioning of the air to ensure that temperatures do not exceed work comfort standards (ACGIH, 2011). Especially at depth where heat could become a significant issue. An ice stope thermal storage, using ice as the storage medium is being proposed as an alternative to provide the heating and cooling—with the ice creation resulting in heating and the ice melting providing the cooling required. A techno-economic investigation of the two systems is undertaken to identify the capital and operating costs for the two systems, and to assess the ice stope’s potential to be considered a low cost and carbon solution for heating and cooling of mines in sub-arctic climates.NATURAL STORAGE SYSTEM – CONCEPT DEVELOPMENTThe concept for the natural storage system is developed from the ice stope at Frood-Stobie Mine, ON, Canada (Stachulak, 1991). The ice stope was developed for mine air heating, with the heating occurring by spraying warm return service water onto the cold intake air—resulting in the air temperature increasing and ice being created in the stope. In summer this ice was melted by passing warm air on top of it, resulting in slight cooling of the air but no significant temperature difference which could allow effective cooling. A schematic of the Frood-Stobie Mine ice stope is provided in Figure 1."

Jan 1, 2019

By G. W. Smith

"The adsorption of dehydroabietylamine acetate on quartz, hematite, rutile and baddeleyite has been deter-mined for concentrations ranging from 0.3 to 5,600 µ. moles/I and for pH values ranging from 2.5 to 10.5.The surface tension, UV and IR spectra, equivalent conductance and ion concentrations for dehydroabiety lamine acetate solutions have been determined.Contact-angle and flotability studies have established that good collection may be obtained with this amine but that selectivity depends on the suitable use of depressants for some of the minerals."

Jan 1, 1971

By E. LaRocque

Denison Mines Limited has been processing uranium ore in the Elliot Lake area for the past 20 years. As the original concept of uranium processing has been modified somewhat over this period, the present paper will describe the current recovery practices at the Denison mill from crushing through concentrate drying and packing . Special emphasis will be placed on the leaching, ion exchange and precipitation sections of the process, with consideration being given to the entire circuit. Descriptions will be given of equipment now being used and control strategies will be discussed.

Jan 1, 1979

By C. R. Powell, W. H. Maher

"This paper presents a short history of the development of milling at Buchans, Newfoundland, and a description of the operation.History and DevelopmentTHE original ore discovery was made at Buchans in 1905 by Matty Mitchell, a Micmac Indian who was prospecting for The Anglo Newfoundland Development Company, which company was then preparing to build a paper mill at Grand Falls, some 50 miles east of Buchans. A development program, initiated in 1906, was terminated in 1911 because of metallurgical difficulties. Intermittent testing was carried out by The American Smelting and Refining Company, and in 1925 a satisfactory method of concentration by flotation was found. Following this, intensive geophysical reconnaisasnce, succeeded by diamond drilling, uncovered two additional orebodies similar to the original discovery at Buchans River."

Jan 1, 1966

By D. G. Almond

Nkomati Nickel Mine in South Africa processes one of the world?s hardest ores in a 375k TPM autogenous grinding circuit. The plant employs an unconventional processing circuit, comprising a primary autogenous mill (AG or FAG) and pebble crushing circuit followed by a secondary hybrid pebble/ball mill and classification cyclone cluster. Advanced Process Control (APC) or Expert Control is now generally accepted as an advantage in most modern high capacity concentrator grinding circuits. This paper reviews the installation of model predictive control at Nkomati and examines the results and benefits of installation in an autogenous mill during plant ramp-up. The paper also demonstrates how predefining process control objectives together with good plant and supplier cooperation can achieve a robust and reliable APC implementation on a very short site program. The results conclusively demonstrate operational and economic benefits during circuit operation with the advanced process control system ON. Production performance and circuit stability were significantly better than during manual control.

Jan 1, 2012

By Charles T. Harper

The uranium deposits discovered by Amok (Canada) Ltd. in the Cluff Lake area of north western Saskatchewan occur at or near the southern edge of the uplifted basement core of the Carswell circular structure. Two types of mineralization, distinguishable, by their geological and structural setting and mineral paragenesis, have been recognized. The N-Claude type is characterized by a relatively simple mineral assemblage, consisting of uraninite or pitchblende with coffinite, and is accompanied by variable amounts of graphite and organic matter, and Fe, Cu, Pb and Mo sulphides. Both N and Claude orebodies occur within quartzofeldspathic gneisses of the basement core. On the other hand, the D-type ore has a complex mineral assemblage consisting of: uraninite, pitchblende, thucholite and coffinite, along with native gold and selenium; gold tellurides, and selenides of Pb, Bi, Ni and Co; sulphides of Fe, Cu and Pb; and organic matter. The D orebody occurs within carbonaceous shales at the base of the Athabasca Formation as well as in fault zones in regolithic quartzo feldspathic gneisses above the inverted unconformity. An age of 1050 m.y., which is consistent with a period (circa 1200-1000 m.y.) of widespread hydrothermal activity and uranium mineralization or reworking within and adjacent to the Athabasca Basin, has been obtained from uranium mineralization from the D orebody. Later reworking (circa470 m.y.) of the mineralization occurred at the intersection of older mineralized shear zones with radial faults produced during meteorite impact.

Jan 1, 1978

By L. H. Van Loon

INTRODUCTION THE property of Madsen Red Lake Gold Mines, Limited lies between Russet and Faulkenham lakes in Baird and Heyson townships, district of Patricia, Ontario. It is about six miles south west of the town of Red Lake, with which it is connected by an all-weather road. All orebodies found to date at the property are silicified lenticular bodies which lie within tuff beds. The ore bas a specific gravity of 2.95. It consists of mica and chlorite schist, silicified and containing a considerable amount of disseminated carbonate, and mineralized with pyrite, pyrrhotite, magnetite, arsenopyrite, and chalcopyrite. Of these, pyrite, in coarse to fine disseminated grains, is by far the most abundant. Pyrrhotite occurs in ?the gangue material as medium to fine disseminated grains. A very small amount of arsenopyrite, in small crystals, is associated with the pyrite, and small grains of chalcopyrite occur in both gangue and pyrite. Although some of the gold present in the ore is quite coarse, a good deal of it is extremely fine.

Jan 1, 1951

By D. Emadi

The ASTM B108 Mould and a Modified Mould were used to cast test bars under a variety of conditions: mould and pouring temperatures, mould coating and tilt. Mechanical properties were determined in the as-cast and heat-treated conditions. The ASTM Mould is less sensitive to casting variables. Enlarging the gating system and adding additional gates to the ASTM mould can improve properties in the tilt position. The reproducibility of properties in as-cast and T6 heat treated bars was investigated.

Jan 1, 2004

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By Ralph H. Cleland

GENERALLY speaking, the Industry lost ground in 1941 in its accident experience. Though the frequency of compensation accidents was but slightly higher than in the previous year and well below past experience, our fatality rate shot up to that obtaining in 1938, and the average cost per man employed was the highest for some time. The number of fatalities was 56 in 1941 as against 33 in 1940. The average cost of compensation per man employed was $34.25 in 1941 as against $28.43. There was but a slight increase in the number of men employed. Accident prevention efforts were maintained, as shown by our frequency, but our accidents were of a more serious nature. In a period of considerable labour turnover, with many new men entering the Industry, especially the base-metal division, and much mental distraction, we might well have expected a high rate of accidents. That this did not occur is a tribute to managers, supervisors, and workmen alike. We all regret the high fatality rate and one must consider why this occurred. So far as it is possible to determine, there is no apparent explanation. There were no disasters. The accidents occurred to the same class of work-men, both in respect to jobs and age groups, and from the same age-old causes that we all know so well. Luck is a big factor in the seriousness of an accident; the solution lies in preventing accidents, even first-aid cases. Generally speaking, if minor accidents do not occur, major accidents do not occur.

Jan 1, 1942

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

By M. Goto, F. Kubota

"In this study, we show the successful separation of rare earth metals, which are indispensable elements for the high-tech industry, from a solution containing a metal mixture by using a liquid-liquid extraction and liquid membrane based on ionic liquids. We employed newly synthesized N, Ndioctyldiglycol amic acid (DODGAA) as an extractant for rare earth metals. The DODGAA exhibited a high affinity for rare earth metals such as Y, Nd, Eu and Dy and the extraction efficiency was greatly enhanced in ionic liquids (ILs). Furthermore, stripping of the metals was readily achieved by using an acid solution. INTRODUCTIONRare-earth metals have important applications in cutting-edge technologies employed in the electronics, information technology, and automobile industries. As Japan does not have many natural metal resources, maintaining a steady supply of imported rare-earth metals is important. The total amount of rareearth metals imported into Japan was 19,000 tons/year in 1996, and this amount increased to 40,000 tons/year over the following decade (Kramer 2010). Japan is now one of the world’s major importers of rare-earth metals (Kramer 2010). However, more than 90% of the rare-earth metals imported into Japan come from China, the world’s leading supplier of rare-earth metal resources, due to their low costs. This situation made us realize the importance of a second resource of rare-earth metals: “urban mines” or discarded electronic waste. Rare-earth metals are generally separated from their natural ores by solvent extraction. However, since urban mines have different metals and the concentrations of rare-earth metals are usually low, highly efficient separation and recovery methods are required for rare-earth metals.Recently, ionic liquids (ILs), which are molten salts at room temperature, have attracted considerable attention since they are novel, environmentally friendly solvents (Kubota & Goto, 2006; Han & Armstrong, 2007). The use of ILs in liquid-liquid extraction of rare-earth metals has been reported (Kubota et al., 2012). In some cases, the IL-based systems showed better extraction ability and selectivity than those showed by the conventional organic solvent extraction systems(Nakashima et al., 2003, 2005; Hirayama et al., 2008; Fang et al., 2012). Therefore, more efficient solvent extraction processes by using ILs can be developed. In this study, we investigated solvent extraction processes in which ILs are employed and discuss the possibility of using ILs in the separation and recovery of rare-earth metals from electronic waste."

Jan 1, 2012

By L. H. Cole

FOR many years Industrial Minerals, or as they were formerly called, 'the Non-Metallic Minerals', compared with the metallics, were considered of only minor importance and as such were given scant attention in the technical press as well as in the public press. Those days are, however, happily passing, and thanks, to an appreciable extent, to the constant endeavour of the Industrial Minerals Section of this Institute, established in the fall of 1932 industrial minerals are now assuming the importance to which they are entitled. The term 'Industrial Minerals', when first adopted in this sense by the Institute, was thought to be original in its application, but it is interesting to note that it had been used many years previously by the Queensland Geological Survey in the following publication: SALT Article 1 in Industrial Minerals by B. DUNSTAN, Chief Government Geologist (Publication No. 268, in Part) Queensland Geological Survey, Department of Mines, Brisbane 1920 In Queensland, however, the term embraced some of the metals as well as the non-metallic minerals proper. The lead furnished by Canada in this matter bore rapid fruit, and already the term 'Industrial Minerals' is widely used, not only throughout Canada but in the United States as well.

Jan 1, 1939

By W. Mueller, M. Rocheleau, E. Dimroth

The paleogeographic evolution of the Abitibi Belt is subdivided into three phases, namely: 1) a phase of the growth of a submarine volcanic chain, 2) a phase of the emergence and growth of volcanic islands and 3) a phase of uplif t and erosion of volcanic islands. Isostatic calculations suggest that the volcanic sequence in the south of the Abitibi Belt rests on oceanic basement or on the mantle; the volcanic sequence in the north of the belt rests on about 13-14 km of tonalitic basement. 10-15 km of plutonic material accreted to the volcanic islands during paleogeographic phases 1 and 2, and caused the uplif t during paleogeographic phase 3.

Jan 1, 1984

By A. W. Jolliffee

ANY attempt to forecast the mineral resources of a largely unknown region is hazardous and, in the case of the Northwest Territories, such a task is even more hazardous than usual. This is not merely because of the immense territory involved (over a million and a quarter square miles), only a small fraction of which has ever been explored or prospected, but also be-cause both the geology and mineral deposits thus far examined show many unique features, and, finally, because the region is being actively prospected at the present time. However, in view of the present widespread interest in Canada's mineral resources, a brief compilation of what is known regarding mineral occurrences and geology in the explored parts of the far north seems timely. From these assembled data, a few inferences are warranted as to future mineral production from this region. HISTORY The story of mineral discovery in the Canadian northwest is a fascinating one. As well, it abundantly illustrates the importance of mineral occurrences in indicating future mining possibilities. The same sequence of events has repeated itself too often to be merely fortuitous.? In most cases, the dis-covery of a mineral deposit of possible economic value has been foreshadowed by the finding of the valuable mineral or an associated mineral in the same district, generally in small quantity, by an early explorer or traveller. Thus, John Franklin reported oil seepages from the base of Bear Rock, near Nor-man, at almost the very spot where oil was struck nearly one hundred years later. Again, some would-be Klondikers, deterred by the hardships of the route, remained to prospect around Great Slave lake, and were the first to report the Pine Point lead-zinc occurrences there and the gold-bearing veins on Yellowknife bay. Sporadic prospecting followed at the latter locality for over thirty years before the recent rich strikes were made. Similarly, in 1847, Dr. John Rae picked up a boulder of copper ore south of Rankin inlet, on Hudson bay. More than eighty years later, a body of copper-nickel sulphides carrying values in platinum metals was found at this locality. Also, the report of cobalt bloom on the east coast of Great Bear lake brought back by a Geological Survey of Canada party in 1900 was a factor in the events leading to the discovery of silver and radium there in 1930.

Jan 1, 1937

By Marcelle A. Hauseux

"The Turgeon Lake granite lies 5 miles north of Baie Johan Beetz, Quebec, at the eastern margin of the Grenville Province. The rocks are classed as granites, granulites, quartzites, biotite schists and gneisses, and amphibolites. The granite's uraniferous character is manifested by phosphuranylite, uraninite, and metamict .zircons associated with magnetite. Field anomalies occur in irregular pods, conformable with the tectonic foliation, in bands roughly paralleling sedimentary bedding. Associated features diagnostic of uraniferous granite are smoky quartz, brick-red feldspar, magnetite and a coarse to pegmatitic grain size. The granite is chemically and physically heterogeneous. Metasediment-granite contacts are diffuse or sharp, and usually conformable to bedding. The regional foliations within all rock types are coherent, and sedimentary structures are often preserved within both metasediments and granite. Autometasomatism probably was a strong granitization agent.A uranium reconcentration into fold-axial zones from original sediments which have been highly granitized during at least two phases of folding is suggested from the available data."

Jan 1, 1977