Search Documents

By F. Awotwe-Appiah, P. Koshy, J. Dankwah, J. R. Dankwah

This research investigates the generation of an effective carbonaceous material from waste ‘pure water sachets’ and their subsequent utilisation as reductants for the reduction of the Opon Mansi iron ore. Composite pellets of Opon Mansi iron ore and pulverised carbonaceous material generated from waste pure water sachets were heated from room temperature to 1200 °C in a gas fired furnace for seventy minutes. The reduced pellet was analysed chemically for its oxygen and carbon content using a LECO Oxygen/Nitrogen and LECO Carbon/Sulphur analysers, respectively. It was observed that nuggets of metallic iron were readily produced with the carbonaceous materials acting as an effective reductant and source of chemical energy. XRD analysis of waste ‘pure water sachets’ revealed that the polymer was semi-crystalline with peaks that were identical to those of high density polyethylene (HDPE). Gas emission behaviour of the iron ore-PWS pellet was studied in a horizontal tube furnace at 1200 °C using an infrared gas analyser; the results revealed an exhaust gas rich in the reducing gases CO and CH4 along with CO2.

Jan 1, 2015

By H. P. Pew

THE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by T HE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by 85 miles wide, is the largest in Canada in areal extent, in the amount of oil in place and in the current producing rate. The discovery well was completed in the middle of 1953. The field has grown until its present area is 369,820 acres. There are 74 working interest owners in the field. Early in the producing history of the Pembina field a committee of operators was formed on a permanent basis. The Pembina Operators' Committee has established a permanent staff, which compiles and distributes pertinent field information on a regular basis to all participants. The Alberta Oil and Gas Conservation Board has dealt with field-wide problems primarily through this committee. Expansion of the field was rapid as shown by the number of wells completed -from 135

Jan 1, 1961

Of the twelve known ore zones on the Sunro property, acquired by Cowichan Copper Co., only the "B" and "C" orebodies of the "River Zone" had been explored sufficiently to indicate the grade and tonnage. The "B" zone was selected for initial production. The portion of this orebody above the main adit level was developed for horizontal-ring, longhole mining. Ore from the stope would be scraped directly to the coarse ore bin. The lack of a suitable mill site on surface, as well as the 8,000-ft. tramming distance, led naturally to the installation ground. I N November, 1960, a lease was obtained by Co-wichan Copper Co. Ltd. (N.P.L.) from Sunro Mines Ltd., covering the main ore (River) zone of the Sunro property. A total of twelve zones had been located on the property. Nine of these lay within the leased area. With the exception of the "B" and "C" orebodies of the River Zone, there had been insufficient exploration for tonnage and grade calculations. Exploration by previous companies had

Jan 1, 1965

By C. M. Kleemann

The paper describes the present milling practice at Western Mining Corporation Limited's new nickel mine at Kambalda in Western Australia. It details the crushing, autogenous grinding, flotation and spray drying circuits for the production of a nickel concentrate. It also indicates some of the metallurgical problems which have been encountered in concentrating this ore.

Jan 1, 1973

By R. Agius, A. Nacu

"Cyanide destruction technologies are implemented at gold and silver operations to comply with the International Cyanide Management Code and meet ever more stringent discharge limits. Currently, the most common chemical cyanide destruction processes used in industry are sulfur dioxide/oxygen, hydrogen peroxide, and Caro’s acid. The cyanide destruction process used at an operation must reliably generate streams of acceptable quality at all times, and depends on numerous factors, including permit discharge requirements, tailings chemistry, location, site-specific climatic conditions and size of the operation. Selecting the most appropriate cyanide destruction process and determining the process design criteria requires accurate laboratory testing. This paper presents and discusses the results of a number of cyanide destruction evaluations that have been conducted to reduce cyanide concentration in process solutions or cyanidation tails. Laboratory testing provides important insights into reagent consumption and other factors required to achieve the target residual weak acid dissociable cyanide (CNWAD) levels.INTRODUCTION Process solutions associated with the extraction of gold and silver contain several forms of cyanide. The most toxic form of cyanide is free cyanide, which can be present as a dissociated cyanide anion (CN-) or gaseous or aqueous HCN. Weak or moderately stable cyanide complexes such as those of zinc, copper and nickel are classified as weak acid dissociable (CNWAD). Although less toxic than free cyanide, weak acid dissociable cyanide complexes are considered “ecologically sensitive” forms of cyanide and are regulated in most jurisdictions. In practice, reported WAD cyanide values comprises both free cyanide and weak acid dissociable cyanide complexes. Cyanide complexes with gold, mercury, cobalt and iron are referred to as strong acid dissociable complexes (CNSAD) and are much more stable, even under mildly acidic conditions. Another term commonly used in cyanide chemistry is total cyanide, which represents all cyanide compounds present in solution. Total cyanide levels in solutions are always equal to or higher than WAD cyanide values and the difference between the two usually indicates the presence of iron-cyanide compounds. Typically in Canada, CNTOTAL levels cannot exceed 1 mg/L in solutions discharged to the environment."

Jan 1, 2017

This paper presents a case study where Cenozoic age detritals and an ancient buried landslide have been modelled in the final walls of an iron ore pit. Orebody 25 is located in Western Australia’s Pilbara region and is an operating pit where a redesign of the final wall cutback was required. The existing slope design utilised a simplistic geological model of mixed conglomeratic, calcretic and clay –dominated detritals overlying deformed bedrock sequences. This simplicity resulted in a conservative design that was not reflective of the slopes performance to that point. Further field investigation was carried out with the results assessed in conjunction with historic drilling, mapping and laboratory testing. A detailed geotechnical model was developed including three conglomerate and two clay dominated units and laterstage calcrete overprinting. The clay units were of significant importance to the stability assessment and resulting slope design due to the thickness and poor strength conditions indicated by the laboratory and field testing. However, the drilling investigation shed only limited understanding as to the origin of the clays and thereby how they should be treated as a component in the stability analysis. A comparison of the ratio of various geochemical elements measured by assay was made between the clays and 1) shale bedrock and 2) clays of known detrital origin from other nearby sites. This indicated the clays had a strong affinity with weathered bedrock. This and other textural features resulted in the interpretation that the clay units were relic debris preserved following ancient landslides in bedrock shale. Using laboratory testing data and calibration of results for a landslide origin, stability analyses were run, resulting in a steeper slope design being implemented. Excavation of the final cutback is now in progress with the model confirmed as appropriate.

Jan 1, 2015

By J. Armitage, J. Erskine

Feed level and thickness measurements are essential in the optimization of an electric arc furnace. A precise measurement of the feed thickness and level gives operators the ability to increase the smelter efficiency and reduce the maintenance cost. Hatch has developed a radar system which is an affordable, low maintenance, and accurate level measurement system. The radar units can be installed across the furnace to measure the feed level and the feed thickness can be calculated with one slag level sounding. The present paper describes the development of radar systems as a process optimizing tool by furnace controls. The authors will discuss the challenges involved in installing eight radar units on the roof of a six-in-line electric furnace.

Jan 1, 2015

By X. Cao

Friction stir processing (FSP) is used to produce wrought microstructures at the surface of sand-cast aerospace grade magnesium alloy ZE41A-T5. It is found that the microstructure is significantly refined in the stir zone and the flow arm. The stir zone is largely comprised of equiaxed magnesium grains of approximately 4.5 pm compared with about 50 µm in the base cast material. In the stir zone, however, abnormal growth of some grains is also observed. Vickers microindentation hardness tests indicated that the stir zone experiences some increases in hardness. Single surface passes with low distortion, lack of pores and cracks were successfully obtained indicating the great potential of the FSP technique for modifying, improving and repairing magnesium alloy castings. This will probably open new opportunities to apply magnesium alloys in aerospace industry.

Jan 1, 2007

By J. Visman

"SummaryThis paper is presented as part of a programme to show the steps taken by industry and others interested in supplying a solid fuel of constant quality to 'satisfy a consuming market. The paper deals with the general principles underlying quality control in coal preparation plants, namely, constant quality and close adherance to acceptance limits. It also describes how control of ash content is ""generally hampered by the problem of coal sampling .and the long duration of the ash analysis and how these difficulties may be overcome.Quality control can be effected in several ways. Thorough blending wll reduce variations appreciably, except those of long trend. The latter can be detected by automatic sampling and quick ash analysis. At present, under favourable conditions, a system of half-hourly ash determinations with an accuracy of 0.5 to 1.0 per cent can be realized, to the effect that trends with a 'wave length' of more than two hours cu be eliminated within the limits of accuracy of the ash figures. The general solution of the problem is a combination of blending, accurate sampling, quick ash determination, and statistical analysis of the pattern of ash distribution.The use of statistical methods of analysis, such as the t test and F test, is •discussed at some length in order to emphasize the importance of the correct evaluation of observational data if there is to be confidence in the validity of test results.General ConsiderationsCOAL, as a fuel, is too cheap for a long haul across the country. The limiting distance depends on the price of the local competitive fuels, and, as the price depends to a great extent on quality, so does quality, to the same extent, command the market."

Jan 1, 1952

By X. S. Fan, T. R. Feng, D. Chen

To meet the flotation process requirements, the large-scale flotation cell must be designed for sufficient pulp mixing, reasonable air dispersion and solid suspension, which is very difficult to design for super large-scale flotation cell. Hence, the flotation cell scale-up and optimization for a short period is a challenge for super large-scale flotation cell design. Computational fluid dynamics simulation has been applied in flotation cell study, which is effective, timesaving and low cost in the study of the flow field distribution for super large-scale flotation cell. This paper demonstrates the flow field characteristics in the 600m3 flotation cell by CFD. The flotation cell model is meshed with hexahedral grid and the high mesh quality assures the computational precision. MRF model, namely a steady-state approximation, ensures that individual cell zones can be assigned different rotational speed. Euler-Euler approach is chosen for multiphase flow simulation to treat different phases as interpenetrating continua. Numerical simulation of single phase, two-phase and three-phase are investigated respectively. Results suggested that the flotation cell has the apparent upper and lower flow circulation. In condition of the impeller rotation, the air is dispersed reasonably. In addition, the solid phase volume concentration distribution in the cell has a little difference.

Jan 1, 2015

By L. T. Loe, A. S. Norsk, Mo i. Rana

High production rate and good stability demand the optimization of all phases of electric pig iron smelting. This is important with respect to slag chemistry, which to a large extent regulates the process temperature in electric smelting. Controlled basicity and slag volume. and a satisfactory screen analysis of the reduction material and sinter, are of the utmost importance for smooth furnace operation. Large variations in slag volume and in B/ A and C/Fe ratio will have an influence on the furnace resistance and thus the specific energy development in the furnace, which lead to variable reduction of SiO.. The result will be variable hot -metal quality and un-stable furnace operation.

Jan 1, 1970

By Tracey Bodnarchuk, Philipp Mirzoev

Sulfate balance control is a common problem for zinc plants. Roast-leach-electrowin plants are mostly concerned with the over-generation of sulfates while for the HudBay direct leach plant both extremes are possible including potential necessity to buy sulfuric acid to replenish a sulfate-depleted circuit, which makes the problem doubly important. Quantitative methods were applied at the HudBay plant to analyze sulfate generation/depletion based on a local sulfur balance and sulfate extraction calculation in the leach circuit, using a Pb-tie method. Main factors were established influencing sulfate generation/depletion, including the critical role of Pb and pyrite. Regression analysis proved to be effective and allowed the quantitative prediction of Pb concentrations necessary to reach the equilibrium for the sulfate balance. This in turn provided a firm basis for a sulfate-control strategy realized through concentrate blend correction, which allowed the plant to fine-tune sulfate generation/depletion effectively reducing economic consequences of excessive/deficient sulfate generation.

Jan 1, 2015

By John C. Wilmot, Robert E. Brewer, Royce J. Smith

In March 2003, Phelps Dodge started up an innovative pressure leach facility for processing copper concentrates at the Bagdad mine in Arizona. This paper describes the development of the concentrate leaching plant at Bagdad and the operational results from start up to present. Optimization efforts and an approach to mineralogical modeling of the concentrate to calculate oxygen utilization are also presented.

Jan 1, 2004

By Alfred E. Pugsley

PAYMASTER CONSOLIDATED MINES, LIMITED, began an investigation into the economy and use of detachable bit drill-steel in June, 1937. This investigation has continued to the present time, and was made necessary by transportation and distribution difficulties that had arisen through the use of standard steel in three widely separated mine areas serviced by a central steel-sharpening shop. Detachable bit drill-steel performance was first studied in the workings of No. 2 mine, where the rock being drilled was composed mainly of porphyry or tourmaline, and where standard drill-steel transportation costs had been excessive. The results obtained in this early work definitely established the economy of detachable bit drill-steel at No. 2 mine. This conclusion was reached when the 're-grind' system of re-sharpening dulled detachable bits was 1n use. Preliminary observations on the performance of detachable bit drill-steel in the quartz-carbonate veins of No. S and No. 6 mines gave encouraging results, and warranted a large-scale investigation under practical mining conditions. All drilling operations were gradually changed over to use of detachable bit drill-steel. This change was completed by February, 1938.

Jan 1, 1939

By Reik M. Winkel

Radar Technologies are successful implemented in the military industry since decades and recently found their way in the mining industry as level gauge radars for bin applications. The latest generation of microwave radar sensors are capable to provide geometrical data of the surrounding area of mining machines, too. Radar sensors are an improvement to laser scanners as they are more robust and able to penetrate dust and mist. Radar sensors will be the key source for operator assistance systems. indurad and RWTH Aachen University conducted a large series of tests at open pit mines and underground coal mines to determine the potential of the new two dimensional Dual Range Radar iDRR. Several applications were determined as highly feasible and are now completed respectively in the implementation stage. The authors are giving an insight in the experimental results, the implementation and an outlook of future applications for this technology.

Oct 1, 2009

By R. Wang

"Under high stress conditions, rock bursts, borehole breakouts, and spalling events are common phenomena that occur around underground openings. In general, together these three phenomena represent brittle failures of an intact rock mass; however, individually they reflect different failure modes under high stresses. After analyzing and comparing the stress-to-strength criteria for rock bursts, borehole breakouts, and spalling events, proposed by previous researchers, it is found that these brittle failure phenomena share common stress-to-strength prerequisite. The stress-to-strength preconditions for brittle failures can be defined by the ratio of the maximum tangential stress around an underground opening to the uniaxial compressive strength (UCS) (s?max/sci) or by the ratio of the maximum far-field principal stress to the UCS (s1/sci). Both these indicators can be used to reflect the same stress preconditions. For s?max/sci, a ratio of 0.4±0.1 represents the critical stress requirement for brittle fracture. However, for s1/sci, a ratio of 0.15±0.05 should be considered as the critical stress requirement. Numerous engineering case studies and analysis of rock mechanics based on the Hoek-Brown criterion also verify these two stress-to-strength preconditions. Here, these two indicators are presented with an error range because complex rock mass quality ratings, lithology, and geotechnical conditions have profound impacts on the stress-to-strength preconditions for brittle failures. INTRODUCTIONHigh stresses are one of the most important factors that must be considered when undertaking underground rock mass projects (Kaiser et al., 1998). Wang et al. (2009) reviewed current progress in the evaluation of high stresses and their corresponding criteria. However, after clarifying the definition of high stress, civil engineers need to understand the deformation and failure behaviors of rock mass around an opening under high stresses. Under high stress conditions, the deformation of rock masses around an opening can be categorized into two groups, i.e., severe brittle failures (or rock bursts) and compressional plastic deformation of the surrounding rock mass, as indicated in Figure 1."

Jan 1, 2015

By J. P. Grau, J. Z. Lu

"Thickeners/clarifiers are widely used in coal preparation plants, potash processing and other mineral processing facilities. Thickeners play a very important role in slurry treatment systems to accomplish solid/liquid separation. The demand for larger plants and the increased thickener handling capacities sometime require thickener diameters as large as 200m. The development and use of high capacity thickeners makes it possible to increase the handling capacity of these thickeners by several to more than 10 times compared to conventional thickeners. Hence, for a given slurry rate, selection of a high capacity thickener will significantly reduce the footprint of the thickener. Much higher handling rate, higher concentration of underflow, clearer overflow and lower capital cost are obvious advantages of high capacity thickeners; however, some process requirements and the concerns of operational cost, especially the flocculant cost of a high capacity thickener operation, keep some engineers selecting conventional thickeners and staying away from the high capacity thickeners. Forty years after the first high capacity thickener was developed, there are still arguments in the selection of conventional thickeners or high capacity thickeners in mineral processing. The arguments will continue unless there is a clear picture of capital cost vs. operational cost for each of the thickener types. The purpose of this paper is to analyze these costs and to provide guidelines for selection of thickeners. INTRODUCTIONThickeners/clarifiers are widely used in various slurry treatment systems. For mining and mineral processing, thickeners are an integral part of the solid/liquid separation system. The feed to the thickeners are processing slurries. The fundamental mechanism for the solids/liquid separation is for the solid particles in the slurry to gravity settle inside the thickener tank. The clear water overflows from the top of the thickener tank and is typically reused in the processing circuit, and the concentrated underflow is discharged to different downstream process systems depending on the application of the thickeners. The general requirements for a thickener operation include high density of underflow and clear overflow. Since thickener operation consists of continuous feeding, overflow and discharge of underflow, the solid particles will gravity settle against an upward flow with its velocity dependent on the feed rate and the underflow discharge rate. Higher feed rates to a given thickener produce higher upward velocities. Underflow discharge is typically relatively small compared to the amount of overflow. The upward flow tends to take particles up to the overflow. Only those particles having a settling velocity greater than the upward flow velocity will possibly settle out. Hence, thickener feed rate has to be controlled so that the required overflow water clarity can be achieved."

Jan 1, 2012

This paper states how alloy and welding advances have made possible the rapid development of the use of aluminum in the construction of equipment for earth moving and off -highway rock hauling. The main details are given regarding the construction and field testing carried out on an aluminum prototype body. The test results of strain gauge readings are analysed, and a description is given of how these have been applied in subsequent designs. The increase in the number of aluminum units put into the various types of service in Canada, as well as the problems encountered, is described, and the experience gained from five years of field service is discussed in some detail. An assessment is also made of the durability of the e units. The economics of using aluminum, together with the current development position, are reviewed, and predictions are made for considerable future increases in the use of aluminum units in open-pit and off-highway operations.

Jan 1, 1964

By B. M. Monaghan

"The developments of the 1950s and 1960s have seen Canada become an international source of iron ore, trading in all geographical areas and hemispheres. Canada's production will significantly increase in the next decade. However, although the outlook is bright, iron ore producers cannot be complacent. Instead, we must weigh the factors that have brought about the development of the Canadian iron ore industry and examine the probable changes for the next decade that will affect its growth.Looking ahead in the 1970s, competition will be severe. Pressure on prices will continue as new sources of supply bid for long-term contracts and as steel producers continue to develop mines around the world. Rising costs will make these pressures more severe. We must balance the growth of the world's steel makers with the emergence of new supplies of iron ore. The iron ore industry is now part of a new era in which demand and supply are intermeshed, and the developments around the world are acting on the Canadian iron ore industry's future."

Jan 1, 1971

By R. Blosser

Phelps Dodge introduced a process improvement model known as Quest for Zero in 2001. In 2004, the focus of Quest for Zero shifted from corporate-led initiatives to projects led by site personnel. The Hydrometallurgical Division at Morenci focused on two (2) significant process improvements: reducing electrolyte bleed and organic losses. In September 2004, Morenci kicked off a bleed reduction project to reduce electrolyte bleed by 45%. By the end 2005, electrolyte bleed was reduced by 55% through understanding and reduction of variance. Significant process changes made during this time period include changes in acid-addition strategy, reduction of uncontrolled bleed, and optimization of bleed placement. In April 2005, the organic reduction project began with the goal of reducing losses by 15%. Operational improvements during this project included improved organic recovery systems, mixer speed optimization, and picket fence installation. By the end 2005, this project reduced organic losses by 35% and current losses are 48% lower than at the start of the project. These projects and smaller Questfor Zero projects have resulted in sustainable annualized savings of $13 million in Morenci hydrometallurgical operations. Through the use of Six Sigma tools, process variances can be controlled and reduced.

Jan 1, 2007