Search Documents

By Inoue T, Takahashi N

To construct the accessing railroad line to the northern portal of Seikan Undersea Tunnel, nine tunnels amounting 7.4km in their total length were excavated through soft mudstones of young- er tertiary era with use of smaller-sized mechanic al excavators. Rocks were classified in four classes to which the tunnel support was designed respectively. Of several combinations of driving equipments stu- died comparatively, the method using the mechani- cal excavators was estimated to be the best choi- ce. The efficiency of the excavator was traced in every construction section and the data colle- cted was reviewed numerically. The result showed that the efficiency of the excavator dropped wh- ere the rocks were as hard as over 200kg/crif for compressive strength. And a few technigues in tunnelling i.e. contr- olling dusts in shotcreting, lattice arch, evaluati- ng measured deformations were tested and review- ed too.

Jan 1, 1987

The optimisation of capital in the total planning context has broadly two components: ò maximising the efficient utilisation of capital against competing capital demands; and ò maximising the efficiency with which the industry's capital requirements are sourced. This paper focuses on the latter of these two concepts, as I wish to highlight that within the coal industry the inefficient sourcing of capital has resulted in the inefficient utilisation of capital. In discussing the optimisation of capital within the coal industry I would like to outline three fundamental issues which currently impact the industry and its application of capital: Initially, from the perspective of an independent investor, the perceived risk associated with investing in a volatile industry cycle has not permitted appropriate funding structures to be created thus leading to an inefficient utilisation of capital. Secondly, investors seeking out a windfall gain have established a practice of trading in the assets rather than encouraging recapitalisation. And lastly the mismatch of supply and demand leading to the establishment of new projects which include a percentage of offshore investment has fostered an environment of lower returns and subsequently a dilution of capital.

Jan 1, 1991

By E Ahern

In exchange for issuing minerals rights from the Crown Mineral Estate to explorers and miners, the Crown expects a æfair returnÆ on this investment, ultimately for the benefit of all New Zealanders. In the case of mining permits, this return is in the form of a tangible asset û royalties from mining activities. But for exploration activity, the return sought by the Crown is an intangible asset û information. The information obtained serves three purposes û in helping Crown Minerals to set work programme conditions during permit allocation, for monitoring the performance of permit holders in accordance with permit conditions, and for archiving and making available for future interested explorers and other parties. Difficulties can arise during the allocation and monitoring process when either party has more information than the other that is not shared. To date not enough emphasis has been placed on the intrinsic value and content of the information generated by explorers and the importance this information can have in the exploration process leading to new mineral discoveries. For attracting exploration investment, the quality and availability of such information, combined with other geoscientific data, is a fundamental determinant for potential explorers when choosing to explore in a global market, and strongly defines the mineral prospectivity for a country. This is something the Australian States and other jurisdictions seeking mineral investment learnt long ago, and who now provide substantial amounts of cheaply or freely available packaged geoscientific datasets, increasingly over the Internet. To have a vibrant mineral exploration industry so that the benefits from the mineral estate can be realised for all New Zealanders, a shift in emphasis to the value of its mineral information base itself is required. Such an approach is befitting of a true Knowledge Economy, and would enable the Crown to make better-informed decisions regarding utilisation of its natural resources.

Jan 1, 2002

By Menne DM

The carbon-in-pulp (CIp)process has become well accepted and firmly established in the gold industry of South Africa and, at this stage, six large CIP plants are treating close to I million metric tons of material per month. Many small operators are also using CIP and additional large plants are either nearing completion, are on the drawing boards,. or are being considered. The programme of testwork that preceded the acceptance of the CIP process in South Africa was conducted over some eight years and has been previously described'-7. With the start-up of the President Brand CIP plant on 'calcine' in July 1980 and that of the Western Areas CIP plant on repulped filter residues in September 1980, the emphasis on the CIP process switched from pilot plants to these large plants - and has largely remained there. As it has started up, each new CIP plant benefited from the experience gained and the developments made, on earlier plants but, since so few plants have so far been established in South Africa, each new plant and each new design has revealed a further set of conditions to be met and problems to be overcome. However, in the highly collaborative atmosphere of the South African gold-mining industry, the results and observations from the operation of these first plants were shared by all mining groups. This paper will attempt to describe typical developments on, and results obtained from, these new large plants, and will incorporate significant results from the earlier laboratory and pilot-plant investigations.,

Jan 1, 1982

By Gillies A. D S, Lee A. H

The major operational objectives of a mine water resource management system (WRMS) are to supply the water needs of the mine and mill, to minimise disturbance to mining due to rainfall flooding or seepage and to dispose of excess water. Historically, company management have placed a significantly lower emphasis on managing the WRMS as compared to managing production. Changing Government legislation concerned with the disposal of water from mine sites is, in many cases making mining companies look more closely at how they manage their water. For example, within the next few years it is likely that prior to mining approval by the Government, mining operations will have to submit water management plans/budgets and contingency strategies in addition to operational plans. While the formulation of a comprehensive water management plan/budget is an additional cost to the company at the mine establishment stage, such plans can be beneficial to the operation in the longer term.The two keys for the efficient design, operation and development of a WRMS are the establishment of written goals which have managerial priority and secondly, access to appropriate good quality data. Managerial priority towards the WRMS will increase as a consequence of the education of mine operators in the benefits to the operation of good WRMS management or less desirably as a requirement to meet Government legislation. The collection of appropriate WRMS data is a more complex issue and to obtain information efficiently and cost effectively relies on the clear definition of the data application.

Jan 1, 1992

By Lunarzewski L, Truong D

Although there are sound principles used in the world recognised methods of gas emission prediction, results based on these methods applied to several Australian longwall extractions have yielded unacceptably high discrepancies. With the development of mining in new seams and at higher rates of extraction, the need has grown for a methodical approach to predicting gas emission levels specifically for local Australian mining conditions. Such an approach is developed from results of recorded emission readings during longwall mining at Appin and Pacific Collieries over the past 6 years.

Jan 1, 1988

By Barria J, Mencho J, Gonzalez GD

An extended Kalman Filter is used to build an on-line estimator of total ore, fine ore and water hold-ups in a SAG mill. In addition, an equivalent grinding rate from coarse to fine ore, as well as the discharge rates of solids (fines) and water are also estimated as part of the adaptation procedure of the model used for the Kalman Filter. The measurements used in the Kalman Filter estimator are the total mill weight provided by load cells, and inferred discharge flows of fines and water from flow and density measurements performed downstream. The net ore and water feed to the SAG mill are used as inputs to the estimator, and also the proportion of fine ore in the feed. As an example of how to introduce robustness in the estimation in the face of sensor bias errors, an estimation of the load cell bias error is introduced in the estimator, thus providing self calibration. The estimator presented in this paper has been tested by simulation using a detailed SAG mill mechanistic dynamic model comprising 27 size fractions well fitted to a pilot mill. The maximum error in the estimation of the operational variables - total and fine ore as well as the mill contents under different operating conditions - is about ten per cent.

Jan 1, 1993

By T Cutts

Since 1989 Kalgoorlie Consolidated Gold Mines has managed the Kalgoorlie gold operations of joint venture partners Normandy Mining Ltd and Homestake Gold of Australia Ltd. Current production from the Fimiston Open Pit is approximately 650 000 ounces per annum. The mine incorporates a multitude of narrow shear hosted, subvertical lodes, predominantly within Golden Mile Dolerite. Traditionally KCGM has used blasthole based grade control in the Fimiston pits. A single sample is taken from vertical production blastholes, drilled on ten metre benches. This process was improved with the addition of infill drilling along blasthole rows to provide additional samples across strike. However the limitations of adequately defining subvertical mineralised structures with vertical blastholes remain. In 1997 the first of two trial areas were drilled with close spaced, inclined Reverse Circulation (RC) drilling. These tests indicated that RC based grade control had the potential to provide significant advantages. These include:improved delineation of mineralised structures, particularly across strike; reliable short-term mine schedules based on the advance data available from drilling over three benches; and the angled RC drilling is capable of providing samples of near stope and stope fill material which often remains unsampled by blasthole drills due to the safety constraints around unstable underground openings. Based on the success of this initial work RC based grade control was gradually implemented across production areas commencing September 1998. Some of the many challenges faced include:development of effective procedures and systems for the planning, logging, interpretation and modelling of the RC data; obtaining adequate drill coverage due to mine scheduling constraints and restricted access around underground openings; requirement for integrated systems to handle either blast hole or RC data; and development of effective methods to evaluate the performance of RC grade control. RC based grade control is delivering significantly improved lode definition, grade estimation and subsequent ore classification.

Jan 1, 2000

Depressed prices for minerals will force the mining industry to became more efficient. The continuous conveying of pit product is one area in which savings can be made. Conveyors are available, or can be adapted to provide the flexibility and reliability required. Each conveying system will need to be custom designed to suit the particular requirements of the mine. The Australian mining industry must take the initiative and accept the challenge of the new technology.

Jan 1, 1986

The first geological maps of parts of Australia were produced in the 1830s and 1840s, many being for purely practical purposes, such as indicating the occurrence of coal, iron and other essential materials. Mineral location maps were also first made about the same time.More systematic geological mapping commenced in the 1850s when large parts of New South Wales and Victoria were studied in government-sponsored surveys by geologists such as Samuel Stutchbury, Alfred Selwyn and Reverend William B. Clarke. Their work coincided with the opening up of most of the major goldfields of eastern Australia, which led to the establishment of Departments of Mines in the separate Colonies (later States within the Commonwealth of Australia).A few companies employed consultant geologists at this time, and the mapping by Frederick Odernheimer is particularly notable. Geological study of Australian ore-deposits and mineralisedareas was influenced by the continental European geological ideas of men such as Odernheimer as well as by those from England. Both geological and mineral maps were a feature of Colonialdisplays presented at major international exhibitions during the second half of the nineteenth century. The maps accompanied rock and mineral collections which showed the known and potential mineral wealth of the Colonies. Such displays raised interest in the potential for development amongst government officials, entrepreneurs and investors in Australia and abroad.By the 1880s most of the Colonies had produced basic geological maps, and several maps of the whole continent had been published. Although systematic mapping of the continent become a reality only in the 1950s, the nineteenth century geological and mineral mapping formed the basis for the development of the major coal, artesian water, and metalliferous mining regions of Australia.

Jan 1, 1990

By Liu X

The solubility of cobalt oxide in iron silicate slags has been measured at 1573 K by equilibration of silica and alumina saturated slags with liquid Co-Au-Fe alloys, and by equilibration of silica unsaturated slag with solid Co-Fe alloys, at oxygen pressures of either 10-9 or 10-10 atm (1 atm = 1.013 x 105 Pa). The activity coefficient of cobalt oxide has been calculated and compared with previous studies.

Jan 1, 1991

By Szpindler G

The results of pot-furnace tests with 35 bituminous coals from 20 seams in New South Wales and Queensland were used to establish the relationship between coal properties, as determined by standard laboratory tests, and the combustion process. The rate of combustion is influenced chiefly by the expansion of the fuel bed, but this cannot be accurately predicted from the crucible swelling number of the coal.The effects of various other factors, such as calorific value and ash yield, were investigated and statistical analysis of the results shows that the coals could be classified satisfactorily according to two experimentally derived parameters, namely heat-release rate at an air flow rate of 260 lb/sq.ft/hr and air flow rate giving stoichiometric combustion. The grouping obtained is shown to be related to ash yield and swelling number.INTRODUCTIQNThe rate of heat release from the fuel bed of a travelling grate stoker and the efficiency with which the heat is used depend upon the design and method of operation of the furnace as well as upon the properties of the fuel. It is difficult to draw general conclusions concerning the influence of fuel properties from tests on a single stoker installation. In the pot-furnace test, on the other hand, a part of the same combustion process as occurs on a travelling grate is carried out in isolation, uninfluenced by furnace design variables, and consequently the effects of coal properties and of the method of pretreatment can readily be demonstrated.While the combustion pot provides a rapid method of assessing the combustion characteristics of a fuel during the ignition and burn-out stages under standard conditions, and of predicting changes in performance with changes in fuel or in air flow rate, it is unable to simulate certain features of furnace design and operation. Data from combustion pot...

Jan 1, 1962

By Fisher AEJ

On Sunday morning 7th November, 1976, at approximately 2-25 a.m., smoke was discovered issuing from the 1912 m long belt drift at Appin Colliery. A Clouth steel cord rubber belt approximately 940 mm in width had been installed in the drift in 1963 on the basis that no fire resistant steel cord belt was then available to operate on a single lift at the load and on the 160 gradient of the drift. Investigation showed that the belt drift was on fire and the usually downcasting drift was upcasting. Immediate fire fighting and rescue operations were instituted and the drift was sealed off. High expansion foam was pushed into the drift from the surface and the fire was brought under control. Recovery work resulted in the fire being put out and the drift open for walking traffic by, S-P0 am., on Wednesday 10th November, 1976. lie experience gained during the fire fighting and recovery operations led to recommendations in regard to future use of high expansion foam.

Jan 1, 1981

This paper aims to provide some' new and original thoughts on tungsten carbide drill-bits and describe practices and performances, some of which are unique and most of which have not previously been described. Many theoretical and descriptive papers and articles on carbide bits have appeared during the last few years, and in the big majority conclusions such as these were made. These results are marked by premature failure of the bits, or The full or economic life of the bit is seldom reached due to the premature failure of the insert. Unfortunately those conclusions are seldom accompanied by the reasons for premature failure. In the few cases where reasons for failure have been advanced, very little, originality has been shown. The reasons usually given are that the failures are due to bad operators, bad workmanship, faulty steel or unsuitable machines, but it has been shown at Mount Isa that the chief reason for poor performnce is bad design.The first question asked will be, "What is wrong with the design of most bits?" and the answer'is, "The size of' the inserts". There may be many other small faults iiI different types of bit but Mount Isa experience indicates that the size of the insert is the most important factor influencing pit life. Under normal conditions it has been found, that there is a minimum size of insert that will give satisfactory performance, and this minimum is 5/16 in width and ? in. depth at the shoulder. A big majority of the bits at presentavailable in Australia do not satisfy these requirements.

Jan 1, 1953

By J G. Petrie, H von Blottnitz

The selection and design of process options to deliver outcomes consistent with sustainable development requires simultaneous consideration of multiple objectives, within a climate of uncertainty û including the environmental and social aspects of technology management in addition to the technical and economic aspects of such. An issue of particular relevance in primary metal production is the deportment of minor and trace components within orebodies, products and wastes and the implications of such deportment for eco-efficiency û in particular, the long-term environmental impact of solid waste management practices. The identification of opportunities to enhance recovery of valuable by-products and simultaneously improve the environmental acceptability of final waste output requires a clear understanding of the distribution of the relevant ore components, which results from the choice of processing route and unit operation efficiency. This is challenging, given that process streams generated during primary metal production are generally poorly characterised and the behaviour and deportment of trace to minor and trace components is not well understood. This paper demonstrates how current data gaps and inconsistencies can be systematically addressed through the meaningful reconciliation of empirical plant data with a fundamental understanding of the mechanisms and parameters influencing element behaviour and deportment during the formation and subsequent beneficiation of mineral ore deposits. On this basis, quantitative distribution data and a comprehensive and comprehensible inventory of unit process inputs and outputs as a function of ore compositions and processing technology options can be generated, which is consistent with early design stage information requirements, both in terms of detail and accuracy, ie is æfirst-orderÆ in nature. This predictive approach to element distribution during primary metal production provides decision-makers with key information in the early design stages of a project (in terms of developing processes within the context of sustainability), whilst simultaneously guiding further data collection and environmental impact prediction studies.

Jan 1, 2006

In preparation of this Paper, the emphasis has been laid on the commercial rather than on the technical and scientific aspects of coal evaluation. It is intended to describe and comment on the principal factors which currently determine the selection and procurement of coking coal for the steel industry, and is not based on the results of any original research by the author. Evaluation of different coals for strictly thermal uses, for gas production or other chemical applications has not been attempted, and comparisons of coal with other fuels have been excluded: the paper is concerned only with coals for the production of blast furnace coke. The discussion is strongly related to, and illustrated by, British, and to some extent, other Western European practice, but it is hoped that the general conclusions may have a wider application.

Jan 1, 1975

The control of industrial grinding circuits in Australian concentrators has been practised for many years in one form or another. Some have established simple feedback loops in areas such as fine ore bin feeders (tonnage control), mill pump sump levels (flow control) and water additions (density control). There are also some sophisticated systems which infer circuit product size using complex measurements of mass flaws and water additions in the circuit and attempts are made to control those flaws to produce a constant circuit product size. The inferred size method in Australian concentrators has become firmly entrenched in the last ten years and control techniques involving the use of direct size measurements with reliable on-stream sizers have been Ignored.

Jan 1, 1983

By Donchak P. J, Champion D. C, Fordham B. G, Domagala J

The Hodgkinson Province forms the northern part of the Tasman Orogen and contains the most extensive outcrops of Silurian - Devonian rocks in Queensland. Deep-water, marine siliciclastic sequences (mainly turbidites) dominate most of the province except near the western margin where mafic volcanics and fossiliferous limestones characterise much of the succession. It is difficult to apply normal stratigraphic mapping techniques to the Hodgkinson Province because of extensive stratal disruption by numerous thrust faults, the general lack of stratigraphic and structural markers, and the unfossiliferous nature of much of the succession. Nevertheless, several distinct units have been delineated although their internal stratigraphy or boundary or superpositional relationships are uncertain. Ordovician strata, as well as two major unconformities have been recognised in the western part of the province. Several models have been proposed to explain the evolution of the Hodgkinson Province. Although there is no general agreement most recent researchers favour an extensional tectonic regime.

Jan 1, 1990

By Bilodeau M. L

The paper describes a model which has been developed to assess the economic charac- teristics of base metal investment in Canada and the effects of past, present and possible future sharing systems, particularly mining taxation systems, thereon. The model is illustrated by applying the 1976 Canadian tax system to the economic characteristics of base metal discoveries made in Canada during the 1951-1974 period.

Jan 1, 1977

By J-P Franzidis

The Floatability Characterisation Test Rig (FCTR) is a self-contained, highly instrumented, mobile pilot plant. It was developed as part of the AMIRA P9 project, primarily to determine ore floatability characteristics and to develop and validate flotation plant modelling, scale-up and simulation methodologies. This paper describes the use of the FCTR in validating the AMIRA P9 flotation model and modelling methodology. In 2001 the FCTR was installed and operated in parallel with WMCÆs (now BHP BillitonÆs) Kambalda Nickel Operation. The FCTR was operated using four different circuit configurations of increasing complexity. Metallurgical surveys, cell characterisation measurements and batch flotation tests were performed around each circuit. This allowed the calibration of a number of flotation models using a combination of data from one, two, three or four circuit configurations. The calibrated flotation models were then validated using predictive validation. To do this, data around a further five FCTR circuit configurations were collected (three of which are presented in this paper). The performance of each of the five circuit configurations was predicted using JKSimFloat V6.1 and the parameters from the various calibrated flotation models. The predicted performance was compared to the experimentally determined performance of each circuit. The validation of the AMIRA P9 model was shown to be largely successful except in the case where the reagent addition (depressant) to the validation circuit was different to that in the calibration circuits. The results also provided information regarding the required complexity of the calibration circuit and how many calibration circuits are required to obtain an accurate prediction of circuit performance. These results have increased the confidence in the AMIRA P9 flotation modelling methodology and have provided important information on what data must be collected to allow the accurate prediction of plant performance using the floatability component modelling approach.

Jan 1, 2007