Search Documents

By Chang TS, Suzuki K, Go H, Nakamura S, Kuwano Y

In 1979, a test operation of an experimental blast furnace was carried out to investigate the behavior of a sort of formed coke, which was used safely by 30% of total coke charge in No.2 B.F., Sakai works, NSC, in 1975". The Mashec-type formed coke of 60 x 60 x 40 mm in dimension was crushed and screened so that it had the same size range (1011,20 mm) as ordinary coke used in the base operation. Preceding to the operation, some experiments on the properties of the formed coke and the effects of crushing on them were performed.

Jan 1, 1981

By Smith IEM

Some samples from arc-type volcanic suites collected in northern New Zealand and southeastern Papua New Guinea show rare earth element (REE) and Y abundances which are enriched relative to the those typical of their respective associations. This enrichment appears to be the result of an alteration process which selectively mobilises the REE and re-precipitates them as REE-bearing minerals in veins and interstitial patches. The alteration is on a micron scale and is not detected in routine petrographic examination. The spectre of REE mobility in young apparently fresh rocks is important to igneous geochemists who use REE abundances to constrain petrogenetic models and may also be important because it indicates the operation of a natural REE enrichment process which could operate in the formation of economic REE deposits.

Jan 1, 1990

By Kasaneva S

The San Cristobal gold district is located 110 km east of the port of Antofagasta, Chile. It contains the San Cristobal gold mine, where Niugini Mining Ltd. commenced a heap leach operation, with initial reserves of 10.1 million tonnes grading 1.34 g/t An, in December, 1990. The San Cristobal district occurs within an upper Cretaceous-lower Tertiary magmatic arc. The main mineralisation occurs within a northwest trending subvertical zone, 1km long and 70-100 m wide, which contains rhyolite porphyry and minor breccia, and is locally termed the "subvolcanic complex". At the San Cristobal mine, most gold mineralisation occurs in subvertical quartz-pyrite veins which were emplaced in dilational sections of an imbricate fault system. The bulk gold resource comprises four ore shoots which formed where the vein system intersects the subvolcanic complex. Gold-bearing quartz-pyrite veins also occur at separate prospects, the Three Sisters and Sol prospects, west and south of the San Cristobal mine. Hydrothermal alteration consists of potassic and propylitic assemblages related to intrusion of the subvolcanic complex. This alteration is overprinted by a phyllic stage which is associated with the emplacement of the quartz-pyrite veins. The oxide zone is 180 m thick, and contains native gold, electrum, limonite, and manganocarbonates. The underlying hypogene zone contains pyrite with minor chalcopyrite, sphalerite, galena, covellite, bornite, chalcocite, and arsenopyrite. Fluid inclusion studies indicate that the deposit formed at approximately 270¦ C, and the mean salinity of the fluid was 4% NaCl equivalent. These observations enable the San Cristobal deposit to be classed as a porphyry-related, mesothermal quartz-vein system of the low sulphidation type.

Jan 1, 1995

By Singh JK, Singh R

With a view to producing increased target output every year, Indian coal mining industry is fast moving towards mechanisation but the present approach of mechanisation suffers from lack of standardisation, mainly due to nonavailability of the cutting data for various machine/rock combinations. The coal seams of the country are relatively hard in nature and the coaling machines are reported to be affecting production and productivity of the coal mine and the very trend of niechanisation. This paper presents the result of extensive study performed to visualise the cutting characteristics of coal seams of compressive strength ranging from 20 MPa to 65 NIPa. In a specially designed drag bit type coal plough rig, continuous recording of cutting forces was done with the help of a microprocessor based data logger and the specific energy of cuttability was evaluated at different depth of cut and speed of cutting. The geomechanical properties such as compressive strength, orientation and frequency of cleats etc. and different indices of coal seams were measured in the laboratory and field and relationship was developed for easy determination of specific energy.

Jan 1, 1992

Since the mid-1970s there has been increasing attention in the South Pacific area to the problems of disaster planning and management at various levels, mainly from regional through national to provincial levels. This concern has been expressed in a variety of ways. International aid donors have made their views known in commentaries or reports. Seminar discussions have been organised at the regional level (such as at Suva, 1976; Suva, 1979; Tonga, 1982 and Suva, 1983). In-country training workshops or meetings have been organised (such as the "Disaster Preparedness Workshops for Non-governmental Organisations" in Pacific countries, jointly run by the Australian Red Cross and the Australian Overseas Disaster Response Organisation and supported by AIDAB, in Vanuatu, 1985; Solomon Islands, 1985; Western Samoa, 1986; Fiji, 1987; Tonga, 1987; Lae and Port Moresby, Papua New Guinea, 1988) or held outside the area (ACDC at Macedon, 1981). Training and/or research institutions have been established such as the East-West Center, Honolulu, and the Asian Disaster Preparedness Center, Bangkok (more Asia oriented). As part of the East-West Center Pacific Islands Development Program's Disaster Preparedness Project, a detailed manual of disaster preparedness and response procedures and guidelines has been published (Carter, 1984).Table 1 and figure 1 show that the area with which this discussion deals is a highly fragmented island region, comprising many small, some minute, nations, both in land area and population. The social structure is predominantly rural, with the capital city often making up a small part of the total population and, in absolute terms, little more than a small town. Outside the administrative and governmental activities concentrated in the capitals, in most cases the indigenous inhabitants depend on subsistence agriculture or on usually a monocultural concentration on a cash crop, most frequently coconuts.

Jan 1, 1990

By De Broglio R

The Mae Moh coal deposit was discovered some 60 years ago by villagers who noticed spontaneous combustion of coal outcrops. The first production began in the 1950's to fuel a fertilizer plant and a 12.5MW power station. During the period 1976 to 1979, three 75MW power station units were constructed on site. These have a total daily coal consumption of some 5000 tonnes and are served by a stockyard of approximately 60 000 tonnes total capacity. Stacked coal is reclaimed by means of a front end loader onto reclaim conveyors. During the years 1983 to 1986 four 150MW power station units were constructed east of the eastern seam subcrop, sons 2 km from the original power station complex. These have a daily coal consumption of nearly 12000 tonnes and are served by a stockyard of total capacity 270000 tonnes, equipped with two stackers and two bucket-wheel reclaimers for a totally mechanised system.

Jan 1, 1986

Historic mining across the Bendigo goldfield reached an average mining depth of 750 m over an area of about 16 km by 4 km, with two shafts exceeding 1400 m. Mining ceased in the mid 1900s due in part to increased dewatering and ventilation demands. Water extraction technology of the day, combined with multiple mine ownership, did not allow uninterrupted and thus economic mining activity to prosper. Today Bendigo Mining Limited (BML) is targeting gold-bearing reefs beneath the water-filled historic mine workings. To ensure mining activity can proceed without the risk of water inrush, historic workings are being dewatered by submersible pumps in historic shafts and through a series of underground drain holes intersecting old workings. Due to the high heads involved, individual drain hole development requires rigorous safety control implementation and assessment prior to drilling. Water extracted via drain holes is pumped to the surface through a series of pipe lines and rising mains in conjunction with two staged pumping stations. Both stations are equipped with high-speed centrifugal pumps, each capable of pumping 40 L/s at a static head of approximately 300 m. BML, which operates beneath and within a large city, is confronted with unusual environmental and social challenges compared to many within the mining industry. The raw mine water, which contains elevated salt levels, is piped through residential areas and must comply with strict controls to prevent impacts on the surrounding environment. The final delivery point is BMLÆs water treatment plant at the north end of the city. The water treatment plant utilises chemical pretreatment and reverse osmosis. It is able to process 7 ML of mine water per day at full production. The product is approximately 5 ML of reusable irrigation quality water, which is made available to the Bendigo community for public gardens, sporting facilities and rural irrigation. The 2 ML of brine is directed to a purpose-built evaporation pond facility located 7 km north of the water treatment facility.

Jan 1, 2008

By Warren L. J

In the mineral processing industry solid-liquid separation within a thickener usually requires the addition of a synthetic flocculant to enhance the settling rate of fine particles. The characteristics of the resulting flocculated suspensions may vary considerably depending upon the physical and chemical conditions which prevail during the flocculation process. For example, parameters such as flocculant type, dosage and solution concentration, surface chemical characteristics of particles and the suspension agitation conditions can influence the degree to which the particles aggregate. Aggregated suspensions exhibit various structures, and range from those composed of small, dense aggregates to those containing large, voluminous aggregates. The size distribution and structural type of the aggregates which form within the feed-well of a thickener can have a dramatic effect upon overall thickener performance. Thickener performance cannot be optimized without optimization of the aggregate structure produced in the feed by synthetic flocculant addition. This has required the development of new techniques to quantify the nature of aggregated suspensions, details of which are presented in this paper.

Jan 1, 1989

The aquifer at Phosphate Hill, north-west Queensland, presents special management challenges. The site contains a phosphate rock mine, fertilizer plant and camp. All of the site water is provided by the Duchess Embayment Aquifer, located within the Burke River Outlier of the Georgina Basin. The Duchess Embayment is a triangular shaped, Cambrian marine sedimentary basin consisting of siliceous and calcareous phosphorites, shales, siltstones and sandstones. It is fault-bounded on all sides and has a regional dip of 5¦E. The aquifer is largely confined to the siliceous facies of the Beetle Creek Formation. It has a very flat potentiometric surface and an average thickness of 45 m with confining beds above and below. The siliceous facies derives from weathering of the calcareous phase and is highly transmissive while the calcareous zone itself contains less water and is dependent upon interconnecting fractures for its permeability. Recharge appears to occur where the siliceous facies crops out around the edges of, and within, the Embayment. Aquifer management issues revolve around two points: successful dewatering of the orebody for mining; and efficient management to maintain water quality and ensure supply over the predicted 30-year life of the project. Current operations are extracting water at levels much below that originally estimated. This is having a detrimental effect on mine dewatering with the SWL lowering at a rate slower than anticipated. As a result, ore parcels are now beginning to intersect the water table, providing a major constraint to the mining plan. The aquifer drawdown cone is extensive and very flat so to keep the water table at an appropriate level for mining the management plan will include more aggressive dewatering to lower the level of the entire aquifer. The additional water will either be disposed of downstream or stored in a holding dam or via the use of artificial storage and recharge. Water resource management will also need to maintain the current quality. About 37 per cent of the water currently extracted forms the low chloride supply required by the ammonia plant and the power station. This ratio is expected to remain applicable under any future operating conditions but the low chloride resource is restricted so will require prudent management to enable the supply to continue. At current usage rates aquifer recharge versus use will need careful monitoring to ensure that the resource remains viable in the long-term.

Jan 1, 2003

Traditional techniques for extracting pillars in thick underground coal seams in India are reviewed. Problems encountered are principally control of roof strata and low recovery. Recently developed mechanized methods and projected newer techniques are discussed.

Jan 1, 1986

By Brinkmann J. R

The relative effects of the two basic mechanisms contributing to rock breakage during blasting, shock and gas penetration, are neither well understood nor well characterized, and need further clarification. Blasthole liner (BHL) tests separate the two effects, and by enabling direct measurement of borehole expansion give insight into the shock/gas energy partitioning in rock confinement. The hydrodynamic code DYNA2D is used to simulate the shock effect of the detonation of emulsion in a stainless steel lined hole, and the predicted expansion is compared with experiment. Workers in the past have neglected near-blasthole phenomena and have calibrated models based on stress measurements remote from the blasthole. Extrapolation back to the blasthole has inherent limitations, and indeed, one of the deficiencies of these models is that they have not been able to predict correct borehole expansions, as observed in BHL experiments. DYNA2D has been enhanced by the ICI group with a detonation model which resolves the explosive reaction zone. As a preliminary step towards the ultimate goal of devising a practical damage model, simulations are used to predict the maximum expansion that would take place if the rock were to remain undamaged. Various material parameters are investigated and it is shown that calculated liner expansions are appreciably lower than measured values for high rock yield strengths, while greater than values for low yield strengths.

Jan 1, 1990

By Wilson CJN

The central Taupo Volcanic Zone is a region of intense Quaternary silicic volcanism accompanying rapid crustal extension. Modem central TVZ is the most frequently active and productive silicic volcanic system on Earth, erupting rhyolite at c. 0.28 m' s'. The rhyolites show no major compositional changes with time, but the total extent of magma chamber zonation has changed with the advent of rifting and crustal extension at c.0.7 Ma. At least 34 caldera-forming ignimbrite eruptions have formed a complex sequence of relatively short-lived, nested and/or overlapping volcanic centres in central TVZ. Taupo contrasts with other large silicic magmatic systems in the exceptionally high frequency, but small size, of caldera- forming eruptions. This contrast reflects the thin, rifted nature of the TVZ crust, that precludes the development of long- term magmatic cycles at Taupo.Within central TVZ, non-rhyolitic compositions have been erupted apparently irregularly in time and space; in particular there is no evidence for a geographic separation of basalts from andesites. TVZ is a rifted arc, but its segmented nature, high thermal flux and voluminous rhyolitic volcanism make it unique on Earth.

Jan 1, 1995

By Pyrih R, House A, Shangraw J, Silva AJ

Sunbeam Mining -Corporation has the inten mine with heap leach gold recovery, near spent ore indicated a relatively high ar topographical configuration, the spent across a small drainage and a lake. Du permit for spent ore disposal from th agencies, concerns about the potential contamination by the arsenic were expres conducted extensive studies to addre contamination. These studies consiste( geochemical and geotechnical parameters underlying the proposed disposal si geotechnical investigations were also hydrologic characteristics were include with the use of an IBM PC computer. :ion of opening an open pit gold Stanley, Idaho. Testing of the ?enic content. Due to the local ore was planned to be disposed :ing the process of obtaining a federal and state regulatory for surface and ground water .ed. Sunbeam Mining Corporation is the potential for arsenic of laboratory testing of both of the spent ore, and the soils te. Field hydrogeologic and -onducted. Local climatic and 1 in the analysis of these data Conclusions of studies indicated that although the seepage through the spent ore disposal would contain an elevated dissolved arsenic content, the hydrologic and geochemical characteristics of the site would prevent arsenic migration into the local ground water system. The attenuation of arsenic on soils with high clay content, and dilution after reaching the ground water table would lower the arsenic content to acceptable Concentrations.

Jan 1, 1988

Here, in what is partly a review and partly a personal viewpoint, I take stock of changes in emphasis and comprehension on the subject of basaltic volcanism in the decade that has passed since the completion of the landmark Basaltic Volcanism Study Project (1981). I concentrate attention on the relatively neglected physical-volcanology aspects (in 1988 it was still possible to publish a 340-page book on flood basalts with barely any mention of physical mechanisms).I adopt the useful unifying concept of "volcanic system" to embrace the invariably-present intrusions as well as the volcano; I consider controls exercised by magma-supply rate and modulator-mechanisms on the nature of the system;I emphasize that sheeted-intrusion complexes, consisting either of dikes or inclined sheets (depending on the ability of the system to expand laterally) occur in all eroded major systems and fuel geothermal systems; I show how constraints set by cooling of narrow intrusions cause such complexes to be wedge-like and produce considerable rotations; I consider the role of the level of neutral buoyancy in making magma chambers possible, causing lateral subsurface magma flow and localizing intrusions, while the LNB itself can be accentuated by intrusions; and I examine the possibility that underwater systems could have very different internal structures from systems on land.

Jan 1, 1990

Comalco Limited has recently completed construction of a $50 million kaolin plant at the site of its bauxite mining and industrial minerals operation at Weipa. The plant will produce 100,000 tonnes per annum of coating grade kaolin for the paper industry. Comalco produced the first coating kaolin from the deposit in 1979 on a trial basis. Since then a variety of quality coating grades with specific particle size distributions and brightness values have been prepared. Extensive drilling and bulk sampling of the deposit over eight years has shown that the ore body is large and of a high grade suitable for the production of premium quality coating kaolins. The processing plant technology was developed by Comalco in association with the European kaolin and equipment producer Amberger Kaolinwerke GmbH (AKW). The Weipa kaolin plant is the first of this size to be built in the Pacific Basin region and it will offer the region's paper-coating mills a stable and reliable source of high-quality kaolin, shipped from an established bulk loading port. The paper provides an overview of the development of the kaolin investment the nature of the production process and details the

Jan 1, 1986

There is considerable economic incentive to increase the angle of open pit walls so as to reduce the total volume of waste to be moved to gain access to an orebody. However, a number of slope failures has increased the awareness of mine operators to the potential and consequences of slope failure. Sophisticated methods for the analysis of slope stability have been developed but they rely on an understanding of the appropriate parameters to describe the structural properties of the slope materials. Unfortunately, these properties change with time.The excavation of an open pit mine removes the constraint and weight of the overlying material and allows the newly formed slope to release previously locked in stress. The release of this stress allows the opening of joints and leads to a significant reduction in bulk modulus. The rock mass is also further affected by damage from nearby blasts. Such damage is cumulative and further reduces the modulus of the near surface material and weakens the bonds between structural elements in the slope.

Jan 1, 1992

By Clappison D. J

Since its formation in Papua New Guinea and raising of A$2 million in 1980, Niugini Mining Limited (NML) has grown to a company capitalised on the Australian Stock Exchange at about A$350 million. In 1995 the company produced some 237 000 ounces of gold, 700 000 ounces of silver and nearly 5000 tonnes of copper from its operations at Red Dome, in North Queensland and San Cristobal in The Atacama Desert of Northern Chile. This production contrasts with Niugini Mining's first mining venture at Mt Victor in the Eastern Highlands of PNG which yielded 20 000 ounces of gold and 11 600 of silver between 1987 and 1989. Following the formation of an exploration joint venture in 1982 with Kennecott Explorations (Australia) Ltd, now a subsidiary of RTZ, Niugini Mining's early recognition of the gold potential of volcanic rocks at plate margins led to discovery of the Lihir deposit in July 1982. This deposit containing about 42 million ounces of gold in resources, is one of the largest undeveloped gold deposits in the world. Following raising of equity funds through the float of Lihir Gold Ltd and debt finance in 1995, construction of the mine at a cost of US$673 million is now underway with first full-scale production at approximately 600 000 ounces of gold per year expected in early- 1998.

Jan 1, 1996

Future hard rock mining will gradually move towards complete mechanisation which lends itself to remote control and ultimately to robotic mining. This will require different technical inputs into mining engineering and one of these is in the area of rock'mechanics. Traditional hard rock mining has had little rock mechanics input. Problems arising from high stresses and poor ground conditions have in most cases be remedied after they occurred, in the worst case by abandoning a particular stope or area and starting elsewhere. In a fully mechanised remote or robotic mining situation the financial penalty for such an approach could be severe, as a major part of the production costs will be in the development and the equipment. It is therefore imperative that a complete rock mechanics feasibility study is undertaken before an area is set up for robot mining and that a continuous stability monitoring system is installed that will predict rock behaviour well in advance of mining, such that the necessary ground control measures can be implemented without impeding the continuity of mining. This system will utilise already existing instrumentation such as extensometers and stress cells, and possibly additional improved instrumentation which has to be developed for this particular Application.

Jan 1, 1986

Planning of modern mines entails considerable challenges in the areas of ground control, materials handling, safety, environment, equipment and personnel. Many orebodies are not economical unless efficient mining systems are used to win the ore. Relentless pressures are placed on mine operators to force them to become more productive and to make mines more competitive in modern economies. This has generated an intense drive to adopt technologies that rely on a greater degree of mechanisation, automation and computerisation. There is no turning back; high technology in mines is here to stay: computer controls and monitoring, computer aided mine design, information management systems, etc. During the past 20 years significant advances have been made in the areas of mine design, mine equipment and geomechanics. One could rhetorically ask if the advances in mine backfill technologies have kept pace with developments in other sectors of the mining industry. This paper will look at a few key mining technology sectors and will compare the relative progress of backfill technology to these sectors.

Jan 1, 1998

Shear-flocculation is one of a munber of potential processes for upgrading deposits of finely-grained minerals and, more generally, for separating different types of particles suspended in a fluid.The smaller the particle the more likely it is to follow the fluid streamlines, or be entrained within turbulent eddies, and the less likely it is to deviate from the streamline and attach to bubbles (froth flotation), other particles (selective flocculation) or magnetic poles (wet magnetic separation). As shown in Figure I, a number of ingenious ideas have been proposed to overcome this effect. The suspended particles are assumed to be 1 - 10 µm.Thus, the efficiency of attaching ultrafme particles of the valuable component (solid circles) to air bubbles, as in process A, is poor. The efficiency may be improved by attaching the particles to oil droplets (Ralston, Kart and Newcombe, 1984) to form agglomerates that rise or sink (B), to magnetic particles (C) (Parsonage, 1988) to allow recovery in a magnetic separator (D), to other particles to form aggregates (E) that are then either attached to bubbles (F) or recovered by sedimentation (G) (Warren, 1992), and to pieces of polyethylene (Rubio and Baltar, 1991) that rise or sink (H).In A, C, E, F and H, the forces that are generally used to ensure collisions result in adhesion are hydrophobic forces, hydrodynamic forces and inertial forces (Warren, 1992). These drag particles from the streamlines to allow particle-particle adhesion. In B and E, soluble polymeric molecules have been added to bridge between particles as they approach closely during a collision.The second major consideration is selectivity. Selective adsorption of the hydrophobe or polymer onto the valuable particles is the key. Many subtle effects of surface chemistry are involved in obtaining adequate selectivity. A complication in real systems is that the initial suspension is often naturally coagulated and needs to be dispersed before being selectively flocculated.

Jan 1, 1993