Search Documents

By Reid A. F

Since early 1971 Western Titanium N.L. has been operating an ilmenite upgrading plant on a commercial basis at Capel, Western Australia. In their process ilmenite is pre- oxidized, then reduced in a rotary kiln to a mixture of metallic iron and titanium oxides. The iron is leached out by accelerated rusting in aerated water, leaving a product with titanium content, expressed as Ti02, of about 92%. Samples from different stages of the up- grading process, representing operations over the last two years, have been studied in detail by X-ray diffraction methods, and the sequences of phases and reactions occurring have been determined. Quantitative X-ray studies showed the ilmenite feed materials to consist of a mixture of ilmenite and pseudo- rutile. Pre-oxidation of the ilmenite at =1000¦C leads to the formation of rutile plus a Fe2TiO5-FeTi205-Mn2TiO5 solid solution. The final reduction product consisted of a mixture of metallic iron, reduced rutile and a FeTi05-MnTi205-Ti305 solid solution. The relative amounts of these reduction products were very sensitive to the initial concentra- tions of the minor constituents manganese and magnesium. The effects of variation of ilmenite feed rate, reducing atmosphere,- reduction temperature and controlled addition of magnesium were also studied.

Jan 1, 1973

Drilling has disclosed a sequence of Cainozoic sediments immediately to the west of the Ediacara mineral field containing little or no dolomitic debris in the lower and middle sections, but with gravel beds of dolomite derived from local rocks in the upper part. It is suggested that the lower and middle sequence of Cainozoic strata was deposited over the area of the Ediacara Range, and that this range was uplifted, probably as a horst block, during Quaternary times and was first exposed to subaerial erosion during the upper Pleistocene epoch.Lower Cambrian dolomites with associated stratiform lead mineralization, which formed the target of drilling on the western downthrown block of the Ediacara Fault, were eroded before deposition of Cainozoic sediments.Intense leaching of basal Cambrian dolomites around the periphery of the Ediacara Basin took place during Mesozoic and Tertiary times. This leaching process has resulted in enrichment of copper and lead mineralization in a thick marginal zone of residual clayey material overlain by dolomitic collapse breccia. These zones of leaching and enrichment were preserved under Cainozoic sediments which have subsequently been eroded. The Ediacara Fault appears to have been a major conduit for mineralizing fluids and is the main lineament of the Torrens Hinge Zone. Contemporaneous movements on this fault have controlled rates of depositionand thickness of sediments across the fault during Adelaidean and Cainozoic times. Though latest movements of this fault have been west block down, the predominant movement has been east block down with associated thickening of sediments to the east in the Adelaide Geosync1ine.

Jan 1, 1972

By M Ujihira, M Komazaki, K Higuchi, D F

A diesel engine with a misfiring cylinder is likely to break down in a short time when the engine is used without maintenance. The authors have developed a method of detecting the occurrence of cylinder misfiring and specifying the misfiring cylinder by using wavelet analysis and statistical analysis on the root mean square (r.m.s.) values of two kinds of acceleration waveforms. This detection method is considered superior to traditional methods, which require several accelerometers, especially in terms of simplicity. Since the development of the method, research has been conducted on semi-automatic processing of measured signals and signal transmission from the worksite to a remote office. Field tests confirmed that 1 + 105 points of dynamic data could be transmitted through the mobile multimedia network within 15 minutes, and the time for signal processing was within 15 minutes. Final determination on the condition of a diesel engine in heavy machinery could be achieved within 30 minutes. Shortened processing time is expected by improvement of the processing software.

Jan 1, 2003

By C M. Sennitt, M J. Spadafora

Systematic field evaluation of known gold and clay occurrences in South Korea has led to the recognition and discovery of both high and low sulphidation gold-silver epithermal systems. These are associated with Cretaceous acid-intermediate volcanic centres in the southern parts of the peninsula. The high sulphidation deposits such as Seongsan and Kohung are characterised by pervasive silica-alunite-dickite-pyrophyllite alteration with anomalous arsenic geochemical signatures. Gold mineralisation is associated with fine grained marcasite and pyrite. A low sulphidation quartz vein system observed at the Tongyoung mine comprises multistage colloform banded quartz-carbonate assemblages, with minor manganese and base metals. Gold and silver occur as electrum and tellurium minerals. Some deposits such as Gasado and Dogcheon display both high and low sulphidation alteration assemblages. Early pervasive silica-alunite-pyrophyllite alteration caps formed by acid fluids with a significant magmatic component, occur above cryptocrystalline colloform banded vein systems. The quartz vein stage hosts the precious metal mineralisation and appears to have been deposited by later neutral fluids generated in part through mixing with meteroric water.

Jan 1, 1999

By Pathan AG

This research work is concerned with an investigation of the fracture toughness of sandstone, siltstone, and coal. Tensile failure trades have been examined with three different specimen geonetries, i.e; rectangular bar, round bar (in three point bending), and diametral compression discs. The Stress intensity approach, and J-integral methods were used to evaluate fracture toughness. Results from both approaches are discussed. True crack length was determined after pre-cracking, using the compliance calibration technique. Fracture toughness results of sandstone are independent of crack length and the size of the specimen. Fracture toughness may hence be regarded as a material property for sandstone. In cxnntrast fracture toughness values for !siltstone and coal are dependent on crack Length.

Jan 1, 1986

The patterns of flow of reaction gases through the flash furnace at the Kalgoorlie Nickel Smelter were simulated in a 1:20 scale model using a flow of water. Particular features of the flow down the reaction shaft, through the settling chamber and into the uptake leading to the waste-heat boiler were examined. Inferences were made concerning the effects of the patterns of flow on the efficiency of the smelting reaction, on the entrainment of dust by the gas stream and on the erosion of the refractory lining of the furnace. In addition, the effects of geometrical modifications to the arrangement of the concentrate burners and to the profile of the settling chamber were explored by making these changes to the model and observing the resulting variations in the patterns of flow.

Jan 1, 1991

By R Balusu, P Humphries

In combination with detailed field studies and goaf gas characterisation, computational fluid dynamics (CFD) models have been used to develop optimum and effective strategies for inertisation during longwall sealing operations to achieve goaf inertisation within a few hours of panel seal-off operation. This study has combined detailed analysis of the performance of various inertisation field trials together with CFD modelling results of different inertisation operations in order to develop the optimum inertisation strategies. A number of parametric studies were conducted on the base case CFD models that had been calibrated and validated based on the information obtained from previous inertisation studies and goaf gas monitoring. These studies included changes in inert gas injection locations, inert gas flow rates, seam gradients, and different inertisation strategies to investigate their effect on goaf inertisation. Studies indicate that the strategy of inert gas injection through the MG seal was not as effective as the alternative strategy of inert gas injection at 200 m behind the face. Innovative inertisation strategies have been developed and subsequently implemented at an underground coal mine in Australia. Further investigations have been carried out in the development and demonstration of proactive inertisation strategies with the objective to suppress the occurrence of spontaneous heatings in active longwall faces, in particular under unexpected scenarios such as during slow retreat/face stoppage due to difficult geological conditions. Initial trials at two Australian longwall panels have demonstrated the great potential of this practice to contain the onset of heatings in the goaf.

Jan 1, 2005

By Richardson F. A

Techniques for flotation optimisation were investigated at Cobar [lines Pty:Ltd., in anticipation of the proposed installation of a computer and on-stream analysis. Successful laboratory and pilot plant tests for flotation performance optimisation using the Simplex Evolutionary Operation Technique (Simplex) lead to a full scale plant test using this method. The index developed for" Simplex response evaluation of flotation performance was based on metallurgical and economic criteria. This index was further modified to minimise the effect of head grade fluctuations. The test program was carried out on one of two parallel copper flotation circuits to allow comparison with normal "manual" operating control, and was conducted for thirty eight shifts. Results from the test section operating under Simplex direction were superior to those obtained using normal "manual" operating techniques and demonstrated the use of the Simplex Evolutionary Operation Technique as a method of reducing reagent consumption in flotation but, at the same time, maintaining satisfactory metallurgical performance. Experience in the use of the technique indicated the need for modifications to the rules of Simplex operations. Modifications were proposed, tested and appeared satisfactory.

Jan 1, 1973

By V Lickfold, A J. Crawford, A J. Wilson

A total of 12 alkalic porphyry centres of Late Ordovician age have been discovered in two mineral districts within NSW. The alkalic porphyry deposits are hosted within shoshonitic volcanic centres that formed where a major cross-arc basement structure (the Lachlan Transverse Zone) cut the Ordovician Macquarie Arc. The Macquarie Arc was amalgamated with the back-arc basin sediments of the Wagga Marginal Basin and with the proto-Pacific margin of Gondwanaland to form the Lachlan Fold Belt after the cessation of arc magmatism in the Late Ordovician. Within the Ordovician volcanic belts of NSW, the alkalic porphyries are the most significant mineral deposits economically. The combined resource of the Cadia district porphyries (729 Mt @ 0.79 g/t Au and 0.30 per cent Cu) makes Cadia the worldÆs seventh largest known porphyry gold system and the largest known gold resource in an alkalic porphyry system (574 t Au). Hydrothermal alteration in the alkalic porphyries comprises a complex sequence of potassic, calc-potassic, sodic, calc-sodic, propylitic and late-stage, typically fault-controlled phyllic assemblages. Hematite dusting is common in many of these alteration assemblages, giving the intrusions and the altered volcano-sedimentary host sequences a distinctive pink-orange colouration. Intensely developed hydrothermal alteration assemblages are localised to within a few hundred metres of the composite intrusions that sourced the mineralising fluids, making these deposits difficult exploration targets. Sulfides are typically zoned, with several of the deposits having bornite-rich cores, chalcopyrite-dominant annuluses and pyritic outer haloes. Gold is well correlated with bornite in most of the deposits, and with chalcopyrite at Cadia Hill.

Jan 1, 2002

By Monette J. C, Nulty J. H

High temperatures and pressures are required to obtain acceptable stripping rates. Higher chemically induced stripping rates could reduce the need for higher temperatures which lead to cyanide losses. The higher rates could lead to lower carbon inventories and higher gold production. This paper reports laboratory and continuous test unit data which strongly suggest that the preceding can be achieved. New stripping agents demonstrate efficient stripping under conditions of cyanide depletion such as after carbon acid washing. Stripping times for gold and silver can be reduced by at least half compared to caustic cyanide through the use of these novel substances.

Jan 1, 1991

The evolution of the Oaky Creek mining complex provides a good example of the mining cycle in practice. Oaky Creek has been innovative in its choice of mining methods, with virtually the full range of coal mining methods having been used as workings have progressed down dip. The history of the mine is traced through its development (and ownership changes), progressive selection of mining methods as depths of cover to seams being mined have increased, and rehabilitation. This allows the different mining methods to be described and illustrates the concept of æwall-to-wall miningÆ.

Jan 1, 1998

By M P. Sandy

Some Western Australian underground mines are challenged by very high stress gradients. This environment frequently results in poor induced ground conditions and damaging seismic activity. In some cases, rockbursting or squeezing ground has been observed as shallow as 250 m below surface. Very few mines operating at depths greater than 500 m experience no stress-related issues. As a general result of this difficult environment, there are a growing number of mines that are now challenged or have been closed by induced geotechnical problems. Often, the up-front savings or perceived advantage of an inappropriate mine plan may be entirely lost to the real cost of managing the hazards, or a write-down of reserves resulting from access difficulties will diminish the economic position of the mine. From an engineering perspective, it is best if stress-related hazards can be proactively minimised, because reactive measures offer less improvement in risk exposure. In this paper, some examples of sequencing techniques for managing difficult environments are contrasted with examples from mines where developing hazards have adversely affected production or the economic viability of the project.

Jan 1, 2003

By M S. N Hadi, J Hossein

Numerical modelling is extensively used in civil and mining engineering applications because of cost and risk problems associated with different experimental studies. In this study, the effect of resin thickness was evaluated in bolt-grout-concrete interaction and bending behaviour of a fully grouted bolt installed across joints in post failure region. Tests were conducted in 20 and 40 MPa concretes, and modelling simulations were made, using ANSYS version 8.1, to include both with and without different pretension loads. It was found that in all resin thickness, both the strength of the concrete and bolt pretension had major influences on the shear resistance and shear displacement of the reinforced medium. Also it was found that the strength of the surrounding concrete is more important than that of the grout thickness in both the shear resistance and shear displacement when the bolt is pretensioned.

Jan 1, 2005

By Meloy TP

Several important, fundamental aspects of the grinding behaviour of mineral systems are addressed. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the steady-state and dynamic population balance model (PBM) grinding equations to obtain the mill matrices and grinding selection and breakage rate functions, respectively. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalisation assumption. The severity of the non-uniqueness problem for steady state grinding is demonstrated in several examples using typical feed distributions and mill matrices. In addition, it is also demonstrated that when higher than single powers are used in steady-state mill matrix expressions during simulation or calculation (or iterative procedures are used during numerical simulation) and four or more size intervals are used considerable amount of error is propagated throughout any calculation. Each solution to a PBM, while giving the same prediction during a single mill pass, gives different solutions or predictions for mill composition upon subsequent passes. In addition, it is shown that there is a problem with building up a grinding mill knowledge base with PBMs. A similar analysis was done for the dynamic or kinetic PBM equations. The fact that the dynamic PBM Problem is degenerate or underspecified is also demonstrated. Multiple solutions to the same dynamic PBM equations are provided. Again, it is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the normalisation assumption. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions. The functionalities obtained through constraints were compared with those obtained with the normalisation assumption of Arbiter-Bhrany which relates breakage functions to particle size distribution. The capability of the population balance model to predict grinding behavior over time in various mineral grinding systems was assessed. The required functionality of selection and breakage functions for effective prediction of grinding behavior in mineral systems is discussed.

Jan 1, 1993

By L C. Thompson

A new understanding of the formation of black organic shales in the Illinois Basin has contributed to insights on how to produce methane from these complex reservoirs. These shales are far from simple shallow derived sediments but are in fact the result of a complex series of events which include the intermixing of volcanic detritus and the marine organic material, onlap successions and low energy turbiditic intraformational activity. This has led to a review of the commercial significance of the mid Devonian shales in the sedimentary basins of the eastern half of the USA. These shale sequences are also characterised by very little contribution from the underlying Lower Palaeozoic carbonate formations. The later diagenetic influences and the interaction of sea floor bacteria especially since the mid Devonian have lead to the creation of a major source of energy in the form of methane. Vast areas measured in 1000s of square kilometres are known to contain biogenically derived natural gas as methane. However, this vast resource produces very little gas due to abundance of illite which acts as a major adsorption mineral and creates a refractory situation where though there is abundant gas present the rate of release is clearly subeconomic. This paper will present the results of recent laboratory trials which have indicated that it is possible to create microfracturing using bacteria within the gas bearing shale sequence and also restart the methanogenesis process. As most coal bed methane environments have similar organically derived shales in direct relationship to the coal beds themselves then this paper has ramifications for this industry as well.

Jan 1, 2004

By Worotnicki G, Tillmann V. H

Past experience with fully bonded cable dowels placed as a means of reinforcement in highly stressed crop pillars at the New Broken Hill Consolidated Limited (NBHC) mine indicated such support was not fully effective. Typically overbreak of the crown occurred leaving long lengths of cables hanging from the back stripped of grout and rock with the potential load carrying capacity of the cables not having been fully utilised. This mode of behaviour had been observed in the cable dowelled crowns of three longhole open stopes (EROS) mined to the No. 12 level at NBHC. A system of support with improved mechanism of load transfer from rock to cable and capable of full utilisation of cable strength was proposed for the crown pillars of future Stopes.

Jan 1, 1983

Location & Permit Status Three major Mesozoic Tertiary basins exist along the continental shelf area of southeastern Australia, known as the Bass Strait area. They are the Gippsland (east of the longitude of Melbourne) Otway (west of Melbourne) and the Bass (underlying central Bass Strait between Victoria and Tasmania). The total area, both onshore and offshore, is approximately 100,000 square miles. In March 1960, the Broken Hill Pty. Co. Ltd. acquired exploration title to the continental shelf areas of the Gippsland, Bass and Otway basins from the States of Victoria and Tasmania. The title to that part of the Otway Basin in South Australian waters was granted in July, 1961. Other exploration permits, being 8 miles wide in Gippsland, held by Woodside :E.) Oil Co. N.L., and 15 miles wide along the southwest coast of Victoria, held by Mobil-BP-Interstate Oil (Frome-Broken Hill Co. Pty. Ltd.), were in existence prior to granting the B.H.P. title. Subsequently, Shell, B.H.P., Esso and Magellan have been granted title to the remaining areas of the continental shelf in the basins under discussion. In three separate agreeme negotiated between 1964 and-1966, Esso obtained farm-in rights to B.H.P.'s Gippsland, Bass and Ott' Permits.

Jan 1, 1970

Some mqre facts and inferences are presented in amplification of a recent paper on the geology of the Kalgoorlie Golden Mile stressing the volcanic origin of its rich gold ores, some of which are considered tobe exhalites. Previously unpublished and largely unmapped pyroclastic features in carbonated and chloritized, but not in amphibolitic, country rock are brought to attention. This applies particularly to the main host, viz. the relatively coarse-grained quartz dolerite greenstone (Q. D. G.), i.e. Golden Mile Dolerite, and gives more credibility to the spatial association of the rich Green Leader and telluride ores with bodies of sediments and tuffites occurring within, or adjacent to, Q. D. G. There may be an intrusive relationship with contiguous mafic amphibolites of doleritic origin, but this is not certain and can only be resolved by morecomprehensive mapping than in the past. Volcanic features have always been recognized in CalC Schist, i.e. Paringa Basalt, more so recently in the shape of coarse volcanic breccia.Iu the subsequent deformation of the gold ores since their inital emplacement there appears to be a structural parallel with some Canadian base-metal deposits, most of them of volcanogenic origin.

Jan 1, 1976

The uptake of nickel into the lattice of pyrrhotite,Fel_oS has been studied experimentally in the temperaturerange 200 DC to 760 DC. Nickel from both aqueous solutionsand salt melts diffuses rapidly into the sulphide latticewith ,an accompanying rel~ase of iron into the solution ormelt. The rate of uptake of nickel and its diffusion intothe sulphide lattice have been followed ,by opticalmicroscopy and by analysis with an electron probe microanalyser.Some geological consequences of this phenomenonaffecting the distribution of nickel in rocks associatedwith nickel-iron sulphide ores are discussed.

Jan 1, 1980

Commercial explosives range from pure emulsions to pure ANFO, with blends of these providing interesting alternatives: energy is often adjusted through addition of aluminium, or the control of density. The energy rating of explosives is derived chiefly from detonation codes, which are used to derive expressions for the internal energy change of the detonation products as they do work under expansion. While all codes used for this purpose work on the basis of Ideal detonation, it is common knowledge that commercial explosives operate in the Non-Ideal domain, which affects the mode of energy delivery to the environment. However, since Ideality represents the foundation from which actual performance evolves, it is valuable to examine the intrinsic energy release of a formulation before attempting to understand the influence of Non-Ideality. In examining the Ideal pressure profile of fundamental formulations, remarkable correlation has been found with field performance, and this increases understanding of the influence of various formulation modifications, especially in regard to the stage at which energy is released, and the effect on rockbreaking. This work has emphasised the value of attempting to understand and define better the non-ideal detonation process.

Jan 1, 2001