Search Documents

By McAllister J

Oxygen was in restricted use at Port Kembla until tonnage oxygen became available for steelmaking in the open hearth furnaces. In adopting the new process various modifications to furnace design and operation were necessary and some of these, including increase in roof height and variation in firing and draft control, are discussed.The design of oxygen lances is also discussed and various steelmakingtechniques considered.Steel production increased with oxygen roof lancing-one- furnace producing 8,507 tons in one week-but new problems, such as rate of refractory wear, and disposal of fumes, were created.Design of future open hearth oxygen furnaces is predicted.INTRODUCTIONIn the post-war era, the availability of "tonnage" oxygen caused a major revolution in steelmaking techniques. Various pneumatic processes showed that steel can be madeat a very fast rate and that oxygen steelmaking can be applied to open hearth furnaces. Methods used are surface impingement with roof lances, bath injection with door lances, flame enrichment with fuel firing, mixed gas and oxygen firing, and enrichment of normal combustion air by oxygen injection into the flue systems.Owing to its previous restricted availability and high cost, oxygen was used in rather small quantities in the open hearth furnaces at Australian Iron and Steel Pty. Ltd.(A.I. & S.), Port Kembla, until about the middle of 1960.At that time tonnage oxygen became available and roof lancing commenced on No. 33 furnace at No. 2' open hearth shop.

Jan 1, 1962

A BRIEF account of the water-power potentialities of Tasmania is given, together with possible applications of the power commercially. A short history of the Waddamana development is then given, and the main works are described.WATER POWER POTENTIALITIESTasmania is an island of approximately 24,500 sq. miles area (exclusive of small islands). An area of 12,000 sq. miles is at an elevation of over 1000 ft. above sea-level, and of 2300 sq. miles at over 3000 ft. above sea-level. Average annual rainfall varies from' over 140 in. on West Coast to 20 in. on East Coast, and for the whole island averages 48.5 in. The total water-power available, based on conservative figures for run off and efficiency, is 6,000,000 b.h.p. Only a small percentage of this total will, under present conditions, and under likely conditions in the immediate future, be capable of being developed commercially.An extensive hydro-metric and water-power survey is at present being carried out in order to collect information concerning the most promising water-power schemes. Already 400,000 b.h.p. has been located in different proposals, and there is still a large area of very likely country along the West Coast which has not been investigated yet. Tasmania thus has very vast power potentialities, which, combined with good ports and communications and wonderful mineral and timber resources, should augur well for the establishment of the great key industries, particularly chemical and metallurgical.

Jan 1, 1923

By Mills JC, Belcher CB

X-ray fluorescence spectrometry is used videly for routine quality control of the mining, )lending and agglomeration of iron ores. Most )f the procedures used, cannot tolerate significant changes in matrix composition or be Lpplied to a wide range of elements. Accord- ngly, a graphite briquette technique which is Lpplicable to some fifty elements in widely Tarying iron ore matrices is described. The ignificant advantages are suitability of the ame preparation for both optical emission and -ray spectrometry, a complete elemental overage for the range 5bcg/g to 100%, and the recision and accuracy of the methods are om.parable with the standard chemical.methods hich have been superseded in the authors' boratories. The proposed methods become ore attractive and economical as more prehensive information is sought.

Jan 1, 1975

By P W. Cleary, M D. Sinnott

Cross-belt cutters are commonly used for sampling coal. They are generally cheaper than falling-stream cutters, particularly when a cutter must be retrofitted. The major mechanisms thought most likely to lead to sample bias are being investigated by discrete element modelling (DEM) in a project funded through the Australian Coal Association Research Program. This paper describes a benchmark run and the current direction of research.

Jan 1, 2008

By Valenti M

A by-product of the lead smelting operations at BHAS is a copper-lead matte typically containing 35% copper, 38% lead and 12% sulphur. A hydrometallurgical treatment process has been developed for the treatment of this matte to recover copper as cathode and results in a lead-sulphur residue which is recycled to the lead smelter. A commercial plant with a nominal capacity of 4000 tpa utilising this process was commissioned during 1984. This plant has been shown to be capable of producing copper cathode at rates approaching 4000 tpa over short periods of time.

Jan 1, 1989

By R H. Boffey

The Osborne copper-gold deposit was discovered in North-West Queensland in 1989. Underground production activities commenced at Osborne deposit in April 1996. This paper will examine technical and operational aspects of the underground mine during its development to a 1.2 Mtpa operation . Technical aspects discussed include geology, mine design and mining methods, equipment fleet selection and capital infrastructure. Operational aspects discussed include the evolution and performance of the integrated work teams that are utilised at Osborne to perform all mining and maintenance activities.

Jan 1, 1998

The importance of orebody definition and optimisation in project development cannot be overstated. Inappropriate orebody definition is the single most important reason for project under performance and/or failure. Without the firm foundation of good orebody definition, the structure of a project cannot be assembled reliably. Many factors need to be considered in the process of orebody definition. These factors are well summed up in paragraph 123 of The Institute's Code and Guidelines for Assessment and Valuation of Mineral Assets and Mineral Securities (Valmin Code). The factors range from the initial geological data through assaying, geotechnical and hydrogeological factors to mining and metallurgical considerations. There are other factors which also need to be considered including marketing and environmental factors. This paper briefly reviews some of these factors and their impact on project development. Three examples are presented where one or more of these factors have had significant impact on the development of the Project.

Jan 1, 1997

A review of major mineral processing and extractive metallurgical developments is made and current areas for research are discussed.

Jan 1, 1975

By P Sutton

The global goal of Sustainable Development is not achievable without major changes in the way goods and services are delivered and material needs are satisfied, which requires tremendous innovation in the supply chains and life cycles in which minerals and energy processing take part. Values derived from minerals and metals processing need to be delivered with a fraction of current ecological impacts, which means removing technical obstacles to eliminating waste and emissions in the minerals cycle. The challenge is to find economically attractive ways to get there, through eco-efficiency gains in existing operations, capturing regional synergies, streamlining and greening the materials supply chain, and commercialising new process technology and new products. This paper summarises the outcomes of the Sustainable Resource Processing project, which was designed to provide a strategic analysis of what sustainability means for minerals and metals processing and how that can be effectively translated into technical and business innovation.

Jan 1, 2002

The treatment meIhods selected for the concentrator at Cobar Mines Pty. Ltd. called for a high degree of automatic control of both the grinding and flotation sections.The resulting concentrator layout includes a central control room overlooking both grinding and flotation sections. The control room houses process recorders, controllers, and indicators. together with motor stopstart stations and alarms.Plant instrumentation includes load cells and variable speed hydraulic drive feeders for feed-rate control of autogenous mills, together with nuclear density gauges, differential flow transmitters, and pneumatic control valves for water and pulp density control.Flotation cell pulp levels are controlled by floats and pneumatic actuators; flotation reagent controls include magnetic flowmeters and time-operated solenoid valves.

Jan 1, 1969

A zone rich in-fish debris in the Rolling Dow= Group in the sub-surface of the Great-Artesian Basin has been discovered a Further research has shoe i this zone to-be of very wide distribution in the Artesian Basin and to occur. at the base of the Ta?nbo .f ormati'on resting on the Roma forma-tion. The zone gives a very characteristic curve on the electric and' gamma ray logs and is thus an excellent correlation marker in the sub-surface over a very wide area. It is probably to be correlated sith.the Toolebuc member described from: outcrops east of Boulia. There .are apparent similarities between the Fishecale zone of the Great Artesian Basin in' Australia and the Fishscale sand of the Western Canada Sedimentary Basin.

Jan 1, 1962

Much of New Zealand is comparatively young geologically in the sense that it has only recently been uplifted. In many places young marine sediments are to be found at high altitudes, as evidenced by the existence in the North Island of Pliocene shell limestones which form prominent escarpments at altitudes of about 3000 ft. inthe central part of the Island, and remnants of the same formation found on the summits of the northern Ruahin.e Range at altitudes greater than 4000 ft.

Jan 1, 1962

By T Galvin

Drilling and blasting at Westside Mine near Wallsend, NSW, has presented a challenge for Orica Explosives, Australia. The colliery produces 600 000 tonnes of steaming coal per year from two seams using surface mining techniques. Tapping into underlying coal will greatly improve the yield, but there are many issues which make this an enormous challenge. Hunter Valley Earthmoving engaged Orica Explosives to supply the explosives products and to provide much of the blasting expertise that is needed on the minesite. Hunter Valley Earthmoving and Orica Explosives have proven to be an outstanding, unified technical team on this project. The success of the team is based on good communication, progressive attitudes, extensive expertise in blast design and most importantly, care and accuracy in implementing the agreed upon designs.

Jan 1, 1999

By Sterns UJ, Weller KR

Grinding to sizes less than 80 per cent passing 20 ¦m in both primary and regrind circuits is becoming increasingly important in processing metalliferous ores, as many of the remaining orebodies are very fine-grained and refractory. The process of very fine grinding, however, is expensive, and neither the performance nor the design criteria are well understood. This paper presents some findings from a collaborative research program, one of the objectives of which has been to better understand and improve the performance of very fine grinding circuits. Data from surveys of an industrial tower mill grinding circuit are reviewed and analysed using the population balance models of the CS]RO and 7KMRC. The performance of both models with regard to changes in feed size distribution, ball load and feedrate is assessed using these data. From comparisons between pilot and full scale tower mill operation a prototype scaling methodology is also presented which shows promise in allowing the models to be used to predict the effect of changes in mill Design.

Jan 1, 1993

By Williams DJ, Battino S

The rapid crushing technique for the measurement of gas content of coal consists of accelerating the rate of gas desorption from coal by crushing. This technique allows the determination of gas content in the space of hours rather than days or weeks as required for the traditional slow desorption technique. The crushing technique is used particularly when gas content determinations are urgently required for mine safety purposes. The method is now routinely used in underground coal mines of NSW and to a lesser extent in QLD. Despite the rapidity and efficiency of this method, concerns have been raised upon the reliability of the method to deliver accurate results. Experience in Australia has shown that there is in fact some discrepancy in results between gas laboratories using the rapid crush technique. The development of rapid crushing techniques for seam gas content measurements in Australia and the main causes of variability in the gas content test results were investigated. The gas laboratories participating in the gas content testing were CSIRO Division of Coal and Energy, BHP Technical Services and GeoGas Pty. Ltd.

Jan 1, 1998

The risks faced by organisations are part of a risk continuum. They can be evaluated in terms of hazard, uncertainty and opportunity as well as by the degree of influence they have on conformance, operating performance and strategic objectives. This paper discusses the application of risk management techniques for mitigating blasting hazards, reducing blasting output variability, and implementing blast improvement opportunities. Effective risk management practices can identify and evaluate risks across all levels of the continuum and can deliver realistic assessments of the likelihood and impact of risks on the companyÆs safety and business objectives. This paper does not attempt to present technical details about blasting, rather it aims to provide enough blasting context and examples so that the practical benefits of applying the risk management process to blasting can be fully appreciated. The topics discussed include: explosive management plan; statistical process control; quality blasting, rock-on-ground; Blast Management; Mine to Mill optimisation; and blasting information systems. The concept of a blasting risk management system employing a continuous improvement loop is also introduced. On reflection the insights presented should be extremely useful for observing and understanding which risk face has management focus at a mine site or for a blast site.

Jan 1, 2001

The use of ammonium nitrate/fuel oil explosives is.now well established in most open cut mining operations. Its use. is extending to underground mining. This has been due in a large measure to improvements in the nature of the ammonium nitrate made available from various sources. The addition of surface active agents and water in controlled amounts to the fuel oil has been found to increase the sensitivity of the ANJFO mixture with consequent better explosive properties. It is considered that the surface active agent increases the bond between the ammonium nitrate and fuel oil giving a more, intimate physical and chemical mixing of the oxidising and reducing agent. This results in increased sensitivity and a faster rate of reaction. The increase in sensitivity has been accomplished without any diminution of safety. Tests which demonstrate the safety of this type of explosive are given in the appenuix.

Jan 1, 1964

By Gordon DM

SUMMARY Tyres account for 25-30% of the operating costs of large capacity haul units as used in open-cut mines. Tyre operating costs can be substanti- ally reduced and often contained in real terms by applying knowledge that is now available. This paper describes certain specific advances in tyre management, namely batching, bias adjustment, cumulative plotting and the so-called "pressure-temperature" system of tyre pressure control, originated on the Mt. Newman Mining Company's Newman minesite, and discusses the contribution that each has made to improving tyre management and reducing costs. INTRODUCTION Tyres are a significant cost in mining. Tyre costs make up between 25% and 30% of the operating costs of large (i.e. 100 tonne and larger capacity) open-cut mine haultrucks. On a large mine this tyre cost may amount to several millions of dollars each year. It is a fact that through careful

Jan 1, 1982

By Bradley AJ

Hamersley Iron Pty. Limited mines and pro cesses iron ore from two orebodies at Tom Price and Paraburdoo, situated in the North West of Western Australia. Conventional open pit mining methods are used at both sites in that material is drilled and blasted in benches, loaded by shovels and hauled to the Primary Crushers or dumped on waste or low grade material stockpiles. The present drilling fleet, consisting of eight high capacity Bucyrus Erie Rotary drills has evolved from an initial fleet of a large number of small percussion rigs. There are significant physical differences between the ore types encountered at both mines which nec- essitate the drilling of smaller diameter blast holes at Paraburdoo than those at Tom Price. The drilling practice at each site is dis- cussed, with examples of performance achieve- ments under varying drilling conditions.

Jan 1, 1978

Ore petrology will fundamentally determine the types of metallurgical processes employed for ore treatment, their operational efficiency and the nature of processing problems encountered. It is therefore paramount that the petrological charact

Jan 1, 1998