Search Documents

By Johnson CR, Wilkie G

The aim of the study was to use quantitative mineralogical measurements to predict the processing characteristics of an ore. Samples were taken from a wide range of concentrators processing ores of lead, zinc, copper and nickel. QEM'SEM was used to measure the characteristics of the ore feeding the plant. Concentrate product samples, together with plant operating data were used to give concentrate grade, recovery and grind size information. It was found that the mineralogical measurements correlated well with the metallurgical parameters indicating that these techniques will be very useful for making predictions in feasibility studies and simple plant optimization.

Jan 1, 1989

By I Mason, A Bray, K Smith, T Sindle

Borehole radar is a proven geophysical technology that can be used to map an orebody ahead of mining. This paper will present a case study, where borehole radar is being used within the mining cycle to map out orebody blocks, both as a strategic and tactical tool. Refined equipment and procedures now enables a slimline borehole radar tool to be deployed on the end of drill rods, making it easier and faster to deploy in an underground mine with minimal impact on the mining process. Boreholes are drilled in advance of mining; cover holes to ensure the competence of the hanging wall and geology holes to determine the location and grade of ore are two such examples. All of these boreholes can be entered using a borehole radar tool to map geology and structure ahead. The radar data can provide images of the orebody as well as help detect potential water bearing structures that could impact on safety at a mining face.

Jan 1, 2009

Silver and gold bearing ore from the Palmarejo mine, located within the Mexican state of Chihuahua, contains a complex mix of electrum, native silver, silver sulfides and silver chlorides. This paper presents a case study that describes the selection, development and engineering of a tailored process plant for the recovery of silver and gold from this ore. Process circuit feasibility study modelling, metallurgical test work and engineering studies are outlined. Options considered to optimise the recovery of the contained silver and gold are compared, based upon cost, operability, recovery and engineering aspects. Concentration by flotation was found to be the preferred primary recovery route. Intensive leaching of the flotation concentrate resulted in solution grades sufficient to allow direct electrowinning to be evaluated against the more traditional Merrill Crowe process. The flotation tailings stream is processed through a separate leaching stage as there is sufficient economic metal extractable from this stream. The processing flow sheet, which is designed to maximise the recovery from both the flotation concentrate and tailings, and to utilise a common metal production facility, is presented.

Jan 1, 2009

Mining of the silver-lead-zinc orebodies at the George Fisher Mine officially started in 2000. A review of mining performance to date shows that many of the extracted primary stopes have experienced some degree of hangingwall dilution. The degree of hangingwall failure in the stopes became progressively more extensive throughout mining of the orebodies in 2001 and 2002, culminating in the unplanned catastrophic failure of the 744D stope in which the ore between 13C (2683RL) and 12L (2714RL) sublevels caved into the previously mined cavity between 13L (2654RL) and 13C sublevels. This was followed several months later by another unplanned caving event in a nearby stope, 740D. As a direct result of these unplanned failures it was decided to mine the stopes with a smaller span than had been previously planned and in a primary-secondary pyramidal stoping sequence. To limit the exposure of the stope hangingwall, a hangingwall drive is no longer developed and therefore geologists no longer have access to the detailed geological information that this provided. Geologists at George Fisher Mine have had to be adaptable and flexible in response to these proposed changes and rely more on data from drilling than mapping for their geological interpretation. The result is that the drilling cycle has become much more critical in the planning process.

Jan 1, 2003

By J M. Parr, C J. Yeats

Discovered in 1991 by combined plume detection and bottom-tow photography (Binns and Scott, 1993) and for some years thereafter the highest tenor mineral occurrence known on the ocean floor, the PACMANUS hydrothermal field has since been surveyed and sampled in great detail by CSIRO and international research agencies (Binns et al, 1995; Auzende, Urabe and Scientific Party, 1996; Binns et al, 2002; Tivey et al, 2006). Since 2005 commercial surveys employing deep-tow geophysical packages and remotely-operated vehicles (ROVs) have been conducted by Nautilus Minerals Inc and partners within Papua New Guinea-granted offshore exploration licenses (Nautilus Minerals Inc, 2008). Two academic drilling programs have been conducted, one under the international Ocean Drilling Program (ODP) directed at deep structure (Shipboard Scientific Party, 2002; Binns, Barriga and Miller, 2007), and one using a 5 m capable seafloor diamond drill to investigate the immediate subsurface at one site (Petersen et al, 2005). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Platinum Group metals have been known in New Zealand since the 1880's but not produced on a large scale. They have been neglected because their value was not appreciated rela- tive to gold and their value was often very low, reflecting demand, and because recovery was difficult compared with recovery of gold. With the rising price of most Platinum Group metals and the perfection of gravity and flota- tion recovery methods, recovery of platinum along with gold from alluvial deposits is more attractive. Platinum Group metals are known in several different environments in New Zealand, ranging from alluvial placer deposits to layered basic to ultrabasic intrusions and quartz veins. None of the known occurrences have been ade- quately prospected and there is a real possibi- lity of future discovery of important deposits. Several New Zealand based and at least two offshore resource companies are currently involved in exploration, prospecting or mining for Platinum Group metals in New Zealand.

Jan 1, 1987

By Deverux M

Heavy mineral deposits accumulate on shorelines with interrupted sediment input. Beach deposits, which form on shallowly dipping coastal plains, are most favourable. However, shallow shelves seaward of cliffed coastlines are known to contain economic deposits. Significantgeologicalconditions are defined, from review of the stratigraphic and geomorphic controls on known deposits , for heavy mineral accumulation on the Swan Coastal Plain.

Jan 1, 1986

By Mouritz M

Ventilation characteristics and the occurrence of nocturnal surface inversions have been investigated within the Mount Whaleback open cut iron ore mine at Newman in Western Australia. When winds are light and/or nocturnal surface inversions form within the pit, episodes of atmospheric stagnation can occur with resultant accumulation of dust, diesel exhaust fumes, and sulphur dioxide evolved from spontaneous combustion of pyritic shale. Nocturnal surface inversions were recorded outside the mine on more than two-thirds of nights. Inside the pit, inversions were much less frequent - occurring on roughly 20% of nights when they were observed outside - and much weaker - the maximum temperature difference being 5 C¦ over 210 m inside the pit compared with 15 C¦ over 150 m outside.

Jan 1, 1988

This paper discusses a number of examples of how environmental factors have been incorporated into the water management aspects of mining projects. One example is the Kingston Lignite Project in the South-East of South Australia where the most significant environmental issue was considered to be the effect of drawdown from mine dewatering and depressurization upon the use of groundwater. By proposing an alternative mining method - the use of floating dredges rather than a two-pass dragline method - drawdown effects would no longer be a concern. A second example is the Pine Creek Gold Mine in the Northern Territory. In this case the principal area of interest from an environmental viewpoint was water management - in particular effluent disposal, contaminated seepage from overburden and tailings, and project water supply. Through an integrated approach to the management of wastes and water the potential for water quality impairment was significantly reduced and external water supply requirements were also significantly reduced.

Jan 1, 1987

Production scale experiment study was carried out in a limestone open-pit for testing the theory and method proposed by the author(Zou, 1987). The results of experiments indicate that the mathematical model and computer programs, which include the consideration of both the three dimentional distributions of the weak planes and the energy densities of explosion stress waves, reflect the physical process of rock bench blasting quite well. The predicted fragment distributions coincide well with the practical fragment distributions measured with the photo-image analysis method proposed by the author(Zou,1989). The paper "A Three Dimensional Mathematical Model for Calculating the Rock Fragmentation by Bench Blasting in the Open-pit"(Zou,1987), which was published in some conferences and journals, has interested some scholors and researchers. In order to test and improve the model, a group of production scale experiments were carried out in a limestone open-pit during 1986-1987. The procedure and results of the experiments are illustrated in this paper.

Jan 1, 1990

Western Deep Levels, a seismically active deep level gold mine, started placing backfill in their narrow tabular workings as part of the regional support strategy in 1986. Over the years the percentage of working places being backfilled has been gradually increasing. At the end of 1995 the support efficiency and the labour productiveness relating to support installation were scrutinised to determine if resources were being optimised. Owing to financial, safety and productivity constraints it was decided to redesign stope support to be less labour intensive, safer and provide an integrated stope support system. This new integrated system will thus combine the previously used temporary, permanent and back area support consisting of mechanical props, hydraulic props and backfill respectively. Backfill previously formed an integral part of the regional support in conjunction with strike stabilising pillars. To design the integrated support system the backfill placement quality has to be exceptionally good and placement must be done as close as possible to the working face. The backfill to face distance was reduced by 30 per cent and in some areas by more than 50 per cent with an increase of square metres filled to increase the effect of the backfill even more. This paper addresses the design and successful implementation of an integrated stope support system based on the optimisation of backfill to the extent where installation of mechanical and hydraulic jacks could be eliminated.

Jan 1, 1998

By Collins D. N

The Olympic Dam Copper Smelter Acid Plant is a hybrid plant capable of producing sulphuric acid from either sulphur burning, metallurgical gases or a combination of both. Commissioning of the Acid Plant on sulphur burning commenced in early April 1988 and commissioning on combined sulphur burning and metallurgical gas commenced in August 1988. During commissioning on sulphur burning a number of acid spills occurred due to balancing of tower flows and control of acid dilution. A number of other significant problems were encountered including failure of boiler gaskets, failure of strong acid pumps seals, the fracture of the teflon dilution water injector and the subsequent failing of the acid circulation pump, tank steel failures and various instrumentation problems. The Commissioning of the Acid Plant on metallurgical gases commenced in August and with the exception of the production of oleum in the boiler economizer was relatively trouble free. Oxygen Plant commissioning commenced in May 1988 and was without significant incident. An outline of the basic equipment for the Acid Plant and Oxygen Plant is presented together with aspects associated with the commisisoning of both plants.

Jan 1, 1989

By H R. Watling, W van Bronswijk

Of the various copper sulfides in the EarthÆs crust, chalcopyrite is by far the most common. This mineral is also the most difficult to leach, with hydrometallurgical extraction processes characterised by prohibitively slow kinetics. While a number of processes, including leaching at atmospheric pressure and temperature, pressure leaching at higher temperature, and bioleaching of concentrates in stirred tanks and whole ores in heaps have been demonstrated to some extent, there is currently no full-scale unit process for the hydrometallurgical extraction of copper from chalcopyrite ores. Titan Resources NL operated a test bacterial heap leach at Radio Hill, Western Australia in 2001, to extract nickel and copper from a mixed sulfide ore that contained significant amounts of chalcopyrite, pentlandite and pyrrhotite. A proprietary mixed bacterial culture was used to inoculate the heap, and the nickel and copper were precipitated from the resultant solution as mixed hydroxides. Although 65 per cent of the copper from the Radio Hill heap was eventually recovered, the rate of extraction followed an unexpected trend, as the initial rates of copper recovery were much slower than column tests had suggested. It was postulated that this was due to dissolved copper precipitating as covellite or chalcocite in the most poorly aerated zones within the heap, ie furthest from the aeration pipes at the base. It was further hypothesised that the lack of oxidants (oxygen, ferric iron) and the likely inactivity of bacteria in these areas limited the re-dissolution of such secondary copper precipitates. In this study the above hypothesis was tested in column experiments using the same mixed sulfide ore and a synthetic leach solution. One set of columns was aerated and another set was operated without aeration. Results showed that precipitation of copper occurred regardless of whether the column was aerated or not. The results suggested that pH of the leach solution played a significant part in the precipitation of the copper. Further column tests revealed this to be the case. These results are described here in detail.

Jan 1, 2004

By Marshall T, Nicholson DS

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while ooencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

By D S. Scovira

The effect of blast vibration on highwall stability is a common concern for many open pit mines. Vibration in such a case is a typical near-field blast vibration situation. Vibration modelling in the near-field of a blast requires consideration of both the amplitude and frequency attenuation of waveforms with distance. Most existing blast vibration models are designed for far-field vibration and do not simulate the frequency attenuation and its effect on waveform shape. With the advent of electronic detonators it is desirable to quantify the effects of blast delay on the amplitude as well as the frequency of blast vibrations. A suitable modelling tool is proposed here. At present, a blast vibration model with double attenuations(amplitude and frequency) has been developed at Orica. The present model simulates the amplitude and frequency attenuations separately using different transfer functions. The amplitude attenuation is modelled according to the non-linear relation between the peak particle velocity (PPV) and the charge weight scaled distance established from the signature hole vibration. The frequency attenuation is modelled with the signal broadening based on KjartanssonÆs transfer function û a linear model for attenuation of waves. The model is capable of taking multiple sets of signature waveforms as input to improve the modelling accuracy of the wave propagation in the geology at a site. The screening effect of the earlier firing holes in the path of a later firing hole is taken into account on not only the amplitude, but also frequency attenuation. The present blast vibration model is suitable for modelling both near-field and far-field blast vibrations. It yields reasonable agreement with measured field data for the near-field vibration examples discussed.

Jan 1, 2007

By Millen M. J, Rainey S, Sowerby B. D

The control of size reduction in grinding machines and circuits may be enhanced by a continuous and accurate measurement of the particle size of solids in appropriate process streams. This paper presents a brief review of commercial particle s

Jan 1, 1997

By Kuruppu M

Geotechnical design plays a key role in mine design. A proper geotechnical design provides a safe working environment and facilitates efficient mining operation. There are mainly three design approaches: (i) judgmental, based on observational and experiential facts, (ii) empirical, based on empirical design formulae; and (iii) analytical, incorporating numerical analysis. Most design applications are based on the design methods one and two as mentioned earlier. However, complexities arise in deep underground mining operations and deep open pit mines. These complexities and difficult geological environment introduce more uncertainties and simple empirical formulae would not be adequate as a design tool. These situations require numerical modelling and analysis of the design problems including interpretation of the results obtained from the analysis. There are several tools available for performing the numerical modelling and analysis. A brief review of the available tools is provided. The authors selected ANSYS (a general purpose finite element analysis tool) for use in mining geomechanics and geotechnical design. This paper includes several examples demonstrating the applicability of this software in designing mining structures. The authors hope that the design examples will demonstrate the use of the numerical modelling and analysis applications in excavation design.

Jan 1, 1995

By Partridge A. C

Pinched Sluices, in a variety of guises, are used extensively for the separation of minerals according to density. In the authors' work a pilot-scale sluice has been constructed with provision for splitting the discharge stream into a number of layers. The composition and flowrate of the stream can thus be analysed as a function of depth and the results presented graphically. The effects of such parameters as total flowrate, pulp composition and particle size on overall performance can be clearly seen from such data.

Jan 1, 1979

Faced with rising costs and lower metal prices, several Ontario base metal sulphide mines have changed their method of mining to vertical crater retreat mining. This is a bulk mining method that utilises large diameter holes and mines successive cuts remotely by blasting and cratering the bottom of the drill holes. The orebody is mined from the bottom up. The method in turn has required a change in materials handling to cope with the greatly increased productivity.   This paper presents an overview of vertical crater retreat mining in the Sudbury area using examples from several producing mines. The paper reviews the history of vertical crater retreat mining, various methods of applying vertical crater retreat layouts, the development of in-the-hole drills capable of drilling the large diameter holes required, methods of explosives loading and blasting to achieve the required cratering effect, methods of ground support including backfill placement, and the ore loading equipment presently being utilised including remote control load-haul-dump units and continuous loaders.   The safety aspect of vertical crater retreat mining has been of concern, and was the focus of a provincial inquiry. The benefits in improved safety are demonstrated through an analysis of various records kept by the mines and provincial agencies.   Future trends can now be envisaged, particularly in relation to deep mining. Some experimental work which could have practical applications, is described.

Jan 1, 1989

Factors influencing Cost, systems available for transporting minerals, particularly on land, and methods used for comparing costs are reviewed. A case study presents comparative costs graphically for coal haulage, assumed in Queensland, by 31-6" gauge rail, belt conveyor, 120 ton road train, slurry pipeline, and transmission of electrical energy by transmission line. The effect on comparative results of alternative methods of including initial capital and capital replacement costs is considered and approximate break-even points between systems, bearing in mind the assumptions taken, are discussed.

Jan 1, 1973