Search Documents

The advancements achieved in rapid tunnelling in the 60's and 70's have been notable. It is unfortunate that shaft sinking has not enjoyed equivalent advances and there are many good reasons why this is so. Technical and commercial considerations have held back development and continue to do so despite the increasing urgency in the search for minerals and energy. By the careful selection of an appropri- ate project and the application of specialist engineering the Bdard took advantage of a unique opportunity to apply a mechanised shaft borer in field conditions.

Jan 1, 1981

Looking back 25 years, the role of the drill and blast engineer in an Australian mine seemed relatively simple, with the primary focal points being scheduling of the drill rigs, oversize control, and budget control with respect to consumption of both explosives and drill consumables. The choice of explosive selection was relatively simple, though many mines were becoming involved in trials of slurry explosives, emulsion blends, and low density ANFO blends. Guidelines to assist the engineer towards specific fragmentation targets were scarce, environmental constraints were light, and computers were rarely found on the desks of any mining engineers. Wall control blasting was in its infancy, with the bulk of attention being given to appropriate slope design and little real attention given to factors such as explosive distribution, and optimum delay timing and sequencing. Quantitative measurement of blasting performance was rare. The science of blasting, for fragmentation control, wall control, and environmental impact control was about to be born, and was heralded in those years by intense efforts by the explosive manufacturers and a proliferation of research centres throughout the world. Since the early 1980s, the role of the Australian drill and blast engineer has gone through a major metamorphosis, and currently requires a greater depth of scientific understanding than any other specialisation within mining engineering.

Jan 1, 2004

By Ramsden AR

The ability of the scanning electron microprobe to provide non-destructive qualitative and quantitative mineralogical analysis at the micrometre scale makes it a very versatile tool for the mineralogical characterisation of ore deposits and their host rocks. With the trend towards exploitation of large tonnage low grade depositsnd precious metals at the parts per million level it is becoming increasingly important to have full mineralogical characterisation and knowledge of the mineralogical residence of the valuable elements to assist formulation of a cost-effective exploration program and obtain optimum recovery in the case of exploitation. Mineralogical applications include

Jan 1, 1989

By Sweet I. P

Stratigraphic correlations across the Mur- phy Tectonic Ridge are crucial to regional corr. elations between the Mount Isa and McArthur River areas. Recent work in the Westmoreland and surrounding areas has substantiated the earlier general correlations between the Mount Isa and McArthur River sequences. The Mount Isa and McArthur Groups, and their equivalents, remain prime prospecting targets for major lead-zinc deposits of the Mount Isa and R.Y.C. type. A prospective area for Redbank-type copper mineralization is suggested.

Jan 1, 1974

By C Aldrich

In this paper, the use of topology preserving projections (Sammon maps) and neural networks are considered as a basis for the construction of multivariate statistical process control charts for a semi-autogenous grinding circuit on a gold plant. Comminution circuits are often operated in a quasi-steady state mode, where the mills tend to move rapidly from one state to another. This makes them difficult to monitor by conventional means designed for continuous steady state processes. As a first step, process data reflecting normal operating conditions are mapped with SammonÆs algorithm. Only one feature is extracted at a time and each mapping is captured by a neural network model to allow online application. Reverse neural network models are used to reconstruct the data prior to the extraction of subsequent features from the data residuals. The ensemble of neural network models can then be used for both fault detection and identification. The approach compared favourable with both linear and non-linear principal component models. It was able to detect two simulated fault conditions both with a reliability of 100 per cent, as opposed to 57.8 per cent and 95.2 per cent detected by an approach based on the use of linear principal component analysis and 84.1 per cent and 98.0 per cent detected by an approach based on non-linear principal components extracted with auto-associative neural networks.

Jan 1, 2007

By Coxhead B. A, Brandt B. A

The geological exploration and evaluation of coal reserves involves the appraisal of very large amounts of data. Computers afford an ideal means of handling and manipulating the data, thereby avoiding the laborious and expensive method of manually compiling the logs in full descriptive language. The Minad system of computer storage and retrieval of geological and analytical data is particularly suited to the description of cores and cuttings from exploration drill-holes. The encoded data is arranged in a 120-column computer output sheet format; descriptive geological information in a 54-column geolog and analytical information in a 64-column assaylog. The acquired data is quantitative, uniform and relatively complete and can be selectively retrieved for processing by a wide range of specialized computer programs developed for the coal mining industry. Visual retrieval of data for manual processing is facilitated by the use of simple codes and logical word abbreviations.

Jan 1, 1977

By Blaskett K. S

The physical properties of monazite and the minerals with which it is associated in east coast beach sands are studied and discussed. Possible means for improving recovery are examined. In particular, it is suggested that the practice of splitting the heavy mineral concentrate into two parts as a preliminary to treatment in separate "rutile" and "zircon" mills can be modified in a simple fashion by the addition of an extra magnetic separation stage so as to aid monazite recovery.INTRODUCTIONBeach sand deposits on the east coast of Australia are a major source of rutile and zircon, and supply 80 per cent or more of world requirements. The deposits also contain a small amount of monazite, averaging about 0.5 per cent of the total heavy minerals. Yet despite a steady price in recent years of £150-160 per ton, monazite production has remained relatively small.On the basis of rutiIe production, potential monazite production on the east coast was about 1,500 tons in 1956, but only 102 tons of high-grade concentrate was produced. The main deterrent to increased production has probably been the capital cost of the necessary equipment. Separate electrostatic and magnetic equipment and separate table concentration and drying constitute a considerable outlay for a by-product contributing 4 to 5 per cent of the revenue from rutiIe.It is the purpose of this paper to discuss monazite concentration generally and to suggest modifications to flowsheets, which may facilitate monazite production while maintaining the main objective, simple and cheap means for maximum rutile production.

Jan 1, 1958

Anyone who has driven backwards using only their rear view mirrors knows how difficult it is to avoid spinning the steering wheel the wrong way. So why run your mine that way? Traditionally Reconciliation has focused on the past performance of the mine. In this paper we make a case for Prognostication û the act of forecasting or predicting something in the future from present indications or signs. Reconciliation is a common activity carried out at most mines around the world. Countless geologists and engineers spend hours poised in front of spreadsheets diligently comparing how their resource/reserve model, grade control, and survey pick ups compare to what was actually produced. The result is usually a group of factors, which are applied to future estimates in an attempt to better predict how the operation may perform. Unfortunately, if the road ahead isnÆt the same as what you have just been down, youÆll be æoff-roadingÆ in no time! An alternative is to constantly collect and analyse key measurements that are used to calibrate critical estimates in an iterative process. When variations occur, they are analysed and corrective action is taken to ensure the estimates and measurements realign. In this way the estimates become forecasts and can then form the basis for decision making to ensure that what does happen in the future will match the plan or schedule. By automating this process, some mines have been able to be proactive on a daily basis in order to improve the overall performance of the operation. This paper outlines the key estimates and measurements used for reconciliation, details the characteristics of an automated web based information management system to facilitate the process and provides some insights about how mining operations might move beyond reconciliation.

Jan 1, 2003

By T Napier-Munn, D J. Bradshaw, M Chauhan, L Keeney

An important aspect of geometallurgy is quantifying mineral processing attributes, which leads to improved orebody understanding. One of these attributes is flotation performance. Several methods have been developed as indicators for flotation performance, including batch testing leading to kinetic information and the standard grade-recovery curve. This paper makes a preliminary statistical comparison between a newly proposed geometallurgical batch flotation procedure and the æstandardÆ batch flotation test commonly used to measure flotation performance in the laboratory. The new test uses much less material than the standard test, and is much faster. It is concluded that the new method follows the final recovery of the standard method well, suggesting that it will be effective in reflecting ore variability for geometallurgical purposes. Comparison of the methods based on the full grade-recovery curve shows less agreement, but this may be due to the fact that the curve is sensitive to the particular experimental set-up and conditions, which make such comparisons quantitatively challenging. Further development work is therefore planned.CITATION:Chauhan, M, Napier-Munn, T, Keeney, L and Bradshaw, D J, 2013. Progress in developing a geometallurgy flotation indicator, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 201-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By J M. Palin

Hydrothermal scheelite precipitated in fault-veins at Paradise, Bonnie Jean, Davidson's and Glenorchy mines display chemical variability involving REE patterns that are transitional between two end-member types. Type I is a MREE-enriched pattern with no or a small positive Eu anomaly. Type II is a flat to MREE-depleted pattern with a strong positive Eu anomaly. The chemical inhomogeneity of these scheelites can be explained by a model of fractional precipitation of REE, with preferential removal of MREE from the fluid during precipitation of scheelite. Irrespective of the mechanism responsible for scheelite precipitation, the source of dissolved constituents is different for scheelites from the Paradise Mine. Bonnie Jean, Davidson's and Glenorchy scheelites formed from LREE-enriched fluids whereas Paradise scheelites precipitated from fluids that were lower in LREE. These inferred fluid characteristics cannot be linked unambiguously to specific source rocks in the region, but could suggest that scheelite deposited in the Paradise fault-vein reflects a more mafic source of REE possibly greenschists, whereas the REE in scheelite from the other mines suggest a more felsic source.

Jan 1, 2003

The Kidston Gold Mine i s located in northern Queensland some 2 Ukm northwest of Townsville. I t is the largest gold mine in Australia and produces approximately 25 percent of Australia's gold and one percent of the world's gold.Initially, traditional mining industry management approaches resulted in the rejection of what appeared to be an attractive low-grade deposit as an uneconomic proposition. Critical re-examination revealed that the rejection was based upon managerial inflexibility and traditionally over-conservative methods of mine evaluation, construction, operation, projected commodity prices and contingency factors. "Ihus it tradition was to prevail, the Kidston prospect would never have been realised.

Jan 1, 1985

IT is most remarkable and valuable property of mediurn and high carbon steels that they should be so susceptible to heat treatment, the wide range of variability in tenacity, ductility, etc, due to the normal influence of the carbon in the untreated material being enormously inereased thereby.The physical properties of steel and other metals are much more closely related to their structure than to their ultimate analysis.For instance, we may by chemical analysis determine the carbon content of a steel to be 0.5% ; but this information alone is insufficient to enable us to say what are the physical properties of the metal.Such a steel may possess 11 tensile strength of anything from 35 tons per sq. in., with much ductility, up to 80 tons per sq. in., with practically no ductility, according to its heat treatment. A microscopie examination, on the other hand, would show the structural composition of the steel, from which its physical properties could be approximately deduced. From this it will readily be understood that the microscope has played an important part in the development of modern rnetallurgy, and to-day it is in daily use for the examination of metals and alloys in the laboratories of most works dealing with the rnanufaeture and working of metals.THE IRON-IRON CARBIDE EQUILIBRIUMTo understand fully the mode of occurrcnce of the different constituents of a knowledge of the Iron-Iron Carbide equilibrium diagram (Fig. I) is essential to heat-treat steel successfully and to interpret microstructures correctly such a knowledge isabsolutely indispensable.A portion of the Iron-Iron Carbide Diagram, dealing with steels below 1000 and containing up to 1 carbon is given below.It should be noted that the diagram deals entirely with pure carbon steels, and does not indicate the influence of the usual so-ealled "impurities" present in all commereial carbon steels...

Jan 1, 1926

By R Turner, P Hatherly, T Medhurst

Borehole geophysical logging data are routinely acquired during exploration of coal deposits in Australia. These data are commonly used qualitatively to identify and correlate coal seams and geotechnically significant interburden rock units. Some quantitative analysis, such as using sonic logs for rock strength estimation is becoming increasingly widespread. This paper discusses results from a project aimed at expanding the quantitative approach to more detailed mineralogical and lithological analysis, which leads to improved geotechnical characterisation for mine planning and mining hazard reduction. A standard suite of wireline logs measuring density, natural gamma, sonic and neutron were analysed from three coal mines in the Bowen Basin. Thirty-nine samples from cored sections of the boreholes were analysed by X-ray diffraction, spectral gamma counts and hyperspectral scanning. Using a standard petrophysical approach to calculating porosity, shale and matrix components from a combination of density, natural gamma and neutron logs, a good correlation with observed mineralogy was demonstrated. However, unusual mineralogies such as heavy minerals or low-potassium clays may distort this analysis. Simultaneous evaluation of all available geophysical logs by modern data mining methods was able to show how these ambiguities may be solved.

Jan 1, 2006

For many years the mining industry at Broken Hill, New South Wales, Australia, was carried on with just sufficient attention to underground ventilation and hygiene conditions as to keep pace with necessity. However, the campaign against industrial diseases in other mining centres (notably South Africa) some years ago, brought the subject more prominently before local mining engineers.Throughout a period of several years, gradual improvement has been effected, and at the present time industrial hygiene is considered an essential part of the production operations of the various companies.In June, 1918, a move was first made by the Board of Trade advising an inquiry respecting the health of employees engaged in the metalliferous mining industry in the State of New South Wales. At the end of that year, a recommendation was made to the State Government by the Board of Trade that a Techni.cal Commission of Inquiry be appointed to examine and report upon the dust conditions of the metalliferous mines at Broken Hill. Following this a second report presented in 1919 made specific recommendations in respect to the scope of such a Commission. A Technical Commission of Inquiry was accordingly appointed and arrived in Broken Hill to inquire into the prevalence of miner's phthisis and pneumonoconiosis in the mines. Early in March, 1920, the examination of all mine employees commenced, and the work was completed in June, 1920. The full report of the activities of the Commission and the conclusions arrived at was officially published at a later date. Based on the recommendations...

Jan 1, 1940

By C Yates, S Jobling, Z Y. Yang

The current trend in the UK towards the adoption of retreat longwall mining methods and the associated rapid development of the access drivages have exacerbated the environmental conditions experienced within these workings. There is a recognised need to improve the efficiency of the design and operation of mine ventilation systems in order to maintain an adequate environment and climate within these workings. Any improvement achieved in the quality, quantity and control of the delivered ventilation will assist in the provision of improved gas and dust dilution and climatic control. The paper presents an analysis of the psychrometric data recorded during the execution of a series of comprehensive climatic surveys conducted within two representative deep underground UK coal workings. The surveys were performed across two high production retreat longwall districts within UK Coal Ltd collieries. The surveys employed intrinsically safe psychrometric transducers and digital data-loggers to collect a continuous record of the mine climate over designated weekday production and weekend non-production periods. The transducers and data-logging units are capable of simultaneously measuring and digitally recording changes in the dry bulb temperature and the relative humidity at regular time intervals for extended periods of time.

Jan 1, 2005

FOR some time it has been recognised by the Metallurgical Staff that the presence of pyrite in the ore was adversely affecting the grades of the flotation concentrates.Following experimental work, it was decided to change over from the acid circuit in the mill to an alkaline circuit. The following description sets out the procedure adopted, -and the results obtained when such change-over was made.The Zinc Corporation ore consists mainly of galena, marmatite, calcite, and quartz, with smaller quantities of pyrite, fluorspar, and rhodonite.A clean specimen of marmatite picked from the ore assayed 53.4% zinc, and 10% iron, with no lead or insoluble. However, as zinc concentrates have been, at times, produced in the plant assaying over 53% zinc, and with only 8.7% iron, apparently the picked specimen of marmatite did not represent an average composition.The average would probltbly be between 8 and 9% of iron, and from 53.5 to 54.5% of zinc. It is obvious, therefore, that from this ore it is not possible to produce zinc concentrate of a higher grade than this average figure.In the Colorado School of Mines Quarterly for April, 1928, Vol. 23, No. 2, on page 47, we find the following statement:As the zinc in the ore exists as marmatite, which contains approximately 54.5% zinc and 10% iron, 49% zinc in the concentrate may be considered high.This statement refers to the ore treated in the Sullivan concentrator, owned by the Consolidated Mining and Smelting Company of Canada Limited.

Jan 1, 1930

By M Roper, M Lovitt

WMC Resources Olympic Dam Operation located in South Australia, is a poly metallic underground sublevel open stoping (SLOS) mining operation with a current annual production rate in excess of 9.0 Mt. Stope size, geometries, geotechnical considerations, drilling and blasting are critical components in stope performance. These factors are further influenced by stringent ventilation requirements due to the presence of airborne radioactive contaminants from uranium mineralisation. Stope planning is complex and mass blasting methodologies have been trialled at Olympic Dam with the view to reducing the frequency of stope blasts, improving stope stability, productivity and ultimately improving overall stope performance. A key aspect in the ability to undertake underground mass blasts of this scale is the application of i-konTM electronic initiation technology by Orica. In the past two years in excess of three million tonnes has been initiated utilising this electronic technology, with an average blast of 250 000 t ranging to the largest to date being 580 000 t. By providing flexibility in blast designs, the use of electronic detonators has allowed mass firings over multiple sublevels. This has resulted in a significant reduction in stope extraction steps compared to conventional pyrotechnic firings. The benefits of this reduction in the number of stope blasts are wide ranging from improved stability of interim stope voids between blasts, reduced blasthole damage, improved blast vibration management and reduction of complex changes to ventilation systems for blasting.

Jan 1, 2004

Permian ultramafic and associated rocks form a belt in East Nelson and contain widespread, but minor, chromite and copper mineralisation and some mining was carried out last century. Since mining ceased, about 1910, little mapping of the belt has been carried out although its origin has been debated vigorously. Recently it has been inferred to form part of a ophiolite sequence, which has been tectonically disrupted to form a melange, and several 'plate -tectonic' models have been proposed. Mapping in the central part of the belt has shown that mTlanges are to the east of the ophiolite sequence. Faulting is widespread so that in anyone section part of the sequence may be absent. Some of the faulting is difficult to recognise and probably took place during or soon after the sequence accumulated. Other faulting is clearly of Cenozoic age and includes major NNE striking faults, with large horizontal displacement, and approximately east-west striking faults with almost entirely vertical movement. The writer agrees that 'plate tectonics' could provide an acceptable explanation for the origin of the ophiolite sequence but the models so far proposed do not take into account the nature and field relationships of the rock units present. Copper Mineralisation is largely controlled by the younger faults, particularly those striking about north-east, and is largely confined to the western part of the ultramafic rocks particularly where slivers of the volcanics of the adjacent Lee River Group are enclosed. Mineralisation, along NNE striking shear zones, has recently been found in the volcanics some distance from the ultramafic rocks. The chromite mineralization is in the form of primary layering in the basal part of the ultramafic belt although in places it has been concentrated into lenses probably during serpentinisation.

Jan 1, 1977

Twelve years ago, Jeffrey Mining Machinery Division of Dresser Industries Inc. developed the 120H HELIMINER. This machine was the world's first fixed-drum continuous miner and soon became the standard among manufacturers of continuous miners throughout the mining machinery industry. This paper will first outline a brief history of continuous miner development, then discuss significant parameters which are essential to a successful continuous miner design, and finally describe a number of specific applications of Jeffrey continuous miners in a variety of materials, such as coal, potash, iron ore, and trona, around the world.

Jan 1, 1978

By Royston, Woods R

ANI Bradken Vortex Pulp Lifters and Grates, both as original equipment and retrofitted to existing SAG mills, are now in field operation. The development of the Vortex leading curve pulp lifter was based on an analysis of traditional radia

Jan 1, 1997