Search Documents

By Thirnbeck M, Sione T, Petrie P, Leach TM, Mori W, Digan K, Harry K

Gold and lesser copper mineralisation are associated with porphyry-related vein systems periph-eral to two separate inferred intrusive centres north of Kainantu, Papua New Guinea (PNG). The intersection of NW trending structures, formed parallel to the Markham Fault, with NE trending transfer structures localise porphyry intrusions, and control vein distrib-ution.The Arakompa veins intrude pre-existing fractures in Akuna granodiorite, located proximal to an inferred porphyry. These veins are characterised by early quartz and later pyrite-chalcopyrite. Gold mineralis-ation is associated with Bi-Te phases in the sulphide veining. At Maniape, en echelon gash veins occur within the imbricate portion of a regional structure. Maniape is a high level carbonate-base metal gold system formed distal to the same porphyry source as Z ?-;4 kmmna

Jan 1, 1994

Gold mineralisation at Wapolu lies within an exposed arcuate zone at the decollement contact between a basement dome of high grade metamorphics and an overlying ophiolite sequence. This contact was originally a thrust fault which has since become a decollement zone for gravity sliding in association with basement doming. Hydrothermal models for the gold mineralisation postulate an epithermal system in which fluids were channelled up the decollement with boiling of those fluids causing hydrothermal brecciation and subsequent gold deposition. The alteration assemblages, fluid inclusion data and geochemistry indicate that the upper levels of the system are exposed.

Jan 1, 1987

By S Bandopadhyay

The seasonal fluctuations of the dust content in Arctic mine environments and the environmental variables affecting the intensity of dust production are qualitatively well known, but quantitative models that allow simulation and prediction of dust generation and the effects of engineering control of thermal regime on the mine environment are still non-existent. In Arctic mines, the migration of moisture in the surrounding rock mass releases fine dust by freeing it from the ice matrix allowing it to escape into mine airway. The migration of moisture is the direct cause for the production of mine dust and heat is the primary driving force. This paper examins the heat and moisture exchange between the ventilation air and the surrounding rock mass in frozen ground, placer mines in the Arctic. Based on the simulated results of a coupled heat and mass transfer problem with phase change, methods of dust control have been identified for mines in the Arctic.

Jan 1, 2005

Claiming the Green Revolution - Protecting Investment in Green Mineral Processing

Sep 13, 2010

1991 New Zealand Branch Annual Conference û Appendix

Jan 1, 1991

Carbothermal Reduction and Nitridation of Ilmenite Concentrates and Chlorination of the Reduced Samples

Sep 13, 2010

Full aerodynamic design development of the proposed fans for the enlarged primary ventilation system at Mount Isa Mines Limited was initiated before tender specifications were prepared. Theoretical and analytical design studies were made of many possibilities to determine the optimum proposal. Major considerations were efficiency, simplicity, standardization, and mechanical feasibility. Model testing and experimental work covered blading design, inlet shape, diffuser and tail fairing dimensions, instrumentation requirements, ancl noise studies.Theoretical and predicted performance estimates were prepared for the three 20 ft diameter vertically mounted axial flow fans.

Jan 1, 1967

By D Fargher

BHP BillitonÆs Cannington operation began production in 1997 and is presently the largest tonnage and lowest cost single mine producer of both lead and silver in the world. The original design capacity was 1.5 Mtpa and this has progressively increased via a series of debottlenecking projects in both the mining and milling operations. In 2003, 2.39 Mt of ore was mined, whilst 2.31 Mt of ore was milled. In February 2003 Cannington received approval to expand the project to a sustainable capacity of 2.4 Mtpa. This resulted in underground development into the northern zone, upgrades to the concentrator, increased accommodation at site and power station capacity. The Cannington project development team implemented a partnership approach to the project. Fraser Osborn Engineering and Outokumpu Technology worked closely together with the Cannington team to meet all of the project constraints.

Jan 1, 2004

By M Surtees

The Limpopo region in southern Africa is considered to be a favourable target for the discovery of base and precious metal mineral deposits. The integration of gravity, geomagnetic, LANDSAT data and geotectonic history is used to formulate an ore deposit model which can be used in the implementation of mineral exploration programmes. Field work was carried out to test and refine the model.

Jan 1, 1993

By W J. Shaw

Geometallurgical modelling is now a hot topic in deposit evaluation and in optimising mine performance; however, its history is long and varied. Historically metallurgical sampling has frequently suffered from a lack of data due to the cost of producing representative bulk samples. In the early 1990s geometallurgical modelling similarly suffered from a lack of data due to complex, time consuming and expensive sampling techniques. More recently, simple and relatively cheap tests for geometallurgical variables such as hardness, grindability, throughput, SAG power index, bond work index, crushing index, mineral recovery and concentrate grade have become widespread. The cheaper sampling has resulted in relatively large geometallurgical databases. However, most of the geometallurgical variables sampled are implicitly (and incorrectly) assumed to be additive when modelled by traditional geostatistical techniques, often leading to ill-informed and costly decisions. Geometallurgical variables are mostly non-additive so the current geostatistical challenge is to develop new approaches to dealing with this type of data. This paper briefly describes a historical case study of geometallurgical modelling of the George Fisher Pb-Zn mine completed in the mid 1990s, then outlines some of the current misconceptions of geometallurgical data and modelling techniques regularly applied to it, and finally discusses some recent developments in geometallurgical modelling, with examples from a number of current clients indicating the direction forward.

Jan 1, 2009

By Canning RG, Uusna S, Goodheart BA

The paper outlines the development of"a process for removal of iron oxides from ilmenite, thereby upgrading the TiO2 content of Western Australian ilmenites, from 55 to approximately 90 per cent. In the first stage, the iron oxides are reduced with solid carbon (coal) to metallic iron. Experimental reduc- tions were carried out in crucibles,, a fluidised bed and a small pilot plant rotary kiln. The reduced'ilmenite is,then agitated in aerated water, in the presence of catalysts, so that the iron "rusts" away from the ilmenite'grains and the precipitated iron oxide is easily separable by decantation. The influence of variables on the rates. of reduction and oxidation are discussed, The oxidation rate was exam- ined for both - the' physical oxygen-transfer characteristics and electrochemically by reference to Peurbaix diagrams, which plot redox potential against solution 'PH, The upgraded ilmenite is expected to be an attractive material. for pigment -manufacture,, and the iron oxide has prospects of being a marketable by-product. The process may possibly be. applied, to .other..ores.

Jan 1, 1964

By M Thomas, S Lambert

The Tugun Bypass Tunnel in Gold Coast, Australia was constructed using diaphragm walls with the top-down cut-and-cover method to allow simultaneous construction of an airport runway extension above the tunnel, whilst excavation of the tunnel continued underneath. The tunnel was built in an environment of high groundwater table and deep deposits of alluvial and estuarine soils with the toes of the walls founded in soil deposits. There was a potential risk for differential settlements to occur between the diaphragm wall panels, caused by the runway fill placed over the tunnel roof during excavation. Dewatering within the diaphragm walls was required to facilitate the construction of the tunnel. The tunnel was also built in an area where environmental considerations were of great importance. Three-dimensional numerical modelling was undertaken to predict the differential settlements of the tunnel with considerations of varying subsurface profile, staged excavation and dewatering, non- uniform surface loading and complex soil-structure interaction. Field instrumentation and monitoring was implemented to confirm numerical predictions.  

Jan 1, 2008

Scale build-up in titanium palladium alloy spent electrolyte heat exchangers in the residue treatment plant commissioned at Risdon, Tasmania in 1971 was shown to be a mixture of manganese dioxide and anhydrite (CaSO4). The manganese dioxide was deposited as a result of thermal decomposition of permanganate ions present in the spent electrolyte. It was shown that deposition of manganese dioxide and associated anhydrite scale could be prevented by prior reduction of permanganate ions to the manganous (Mn++) state by the addition of ferrous ions. In the plant this was conveniently accomplished by injecting into the inlet line to the heat exchangers sufficient zinc plant solution containing ferrous sulfate to decolourise the spent electrolyte. This action prevented deposition of such scale for another 21 years, until the heaters were finally decommissioned in March 1992. Measurements indicated that addition of the reducing solution lowered the anodic potential of the titanium alloy by 200 - 300 mV (depending on the solution resistance), but that it was still +300 to 400 mV with respect to a standard calomel electrode. It was shown that, if necessary, a small impressed current could be applied to provide anodic protection. Before scale deposition was overcome by the addition of ferrous sulfate solution, badly scaled heat exchangers were cleaned by recirculating a solution of hydrogen peroxide in spent electrolyte or dilute aqueous sulfuric acid, after laboratory testing of a variety of possible solvents for the scale. Corrosion tests indicated that attack on the titanium alloy by the acidic peroxide cleaning solution was insignificant.

Jan 1, 2005

By C Standing, R Lacourt Rodrigues, C Q

The value of iron ore depends on the grade of the contaminants. Scheduled iron, and the associated contaminants, provides mine planners with a measure of stockpile feed and blending requirements. Blending at the stockpiles is one approach to optimising iron grade, while minimising the variability of contaminant grades. These schedules are typically based on resource models incorporating geology and iron and contaminant grades. Resource models reflect best estimates of trends for each of the elements rather than the potential variability, which is critical for accurate short-term blending. Conditional simulation provides a tool to describe the likely variability of each element. Only recently has conditional simulation technology allowed the inherent correlation between elements to be incorporated into the process. This paper presents the stepwise co-simulation process used to simulate and describe multi-element variability for effective mine planning. A case study using the multi-element conditional simulation and the subsequent uncertainty in the schedule and stockpile planning is presented. This process supports proactive mine planning to minimise unexpected fluctuations in the final product.

Jan 1, 2005

The following thesis is an outcome of an investigation undertaken by the writer, at the suggestion of Professor Skeats, of the dykes and associated auriferous reefs of the Walhalla-Wood's Point belt, with the view of determining what relation, if any, existed between the petrological nature and the extent of llietasomatic alteration undergone by the dykes, and the genesis and localization of the gold.Although the greater part of the writer's time in the field and laboratory was occupied in studying the dykes and auriferous occurrences, a study was also made of the general geology as a basis for the special investigation. In addition, it soon became evident in the field that secondary enrichment had played a marked part in re-concentrating the gold and some interesting data in this connection have been collected. For example, indubitable evidence has been found of nuggets of gold having been formed by secondary processes.

Jan 1, 1920

By M Wilkes, C-Q Liu

Microbial oxidation of refractory sulphide ores (particularly gold and copper ores) are well-established techniques that are increasingly employed because of their low capital and operating costs and environmental benefits. CSIRO has established a multidivisional project, the æBioMineral Processing InitiativeÆ, with the goal of generating new and improved high temperature micro-organisms for biological oxidation of these refractory ores. The project is currently focused on the discovery/generation of novel hyperthermophiles for the bioleaching of copper from chalcopyrite. As part of this project we are investigating the practicalities of genetic modification of iron/sulphur oxidising micro-organisms. The molecular biology of iron/sulphur oxidising acidophiles is still in its infancy. This work is aimed at improving our knowledge of vectors, promoters, selectable markers, gene transfer and expression in these organisms. The Acidithiobacillus ferrooxidans genome is currently available and genomics is proceeding at a rate where in the next few years we can expect at least one or two relevant microbial genomes to be sequenced each year. New genes that impart useful characteristics to iron/sulphur oxidising acidophiles will be available from published genomes and the study of newly isolated hyperthermophiles. We need to be in a position to clone and express those genes. This paper will describe the isolation, transfer and expression of thiocyanate hydrolase genes in Escherichia coli and At. ferrooxidans. Most common antibiotics are not effective against iron/sulphur oxidising acidophiles. Also, the use of antibiotics or their resistance markers outside of a laboratory setting would not be appropriate. Resistance to thiocyanate should be a useful selectable marker, without implications for human or animal health. Additionally, thiocyanate resistant iron/sulphur oxidising acidophiles might have application in gold bio-oxidation plants in arid areas where reuse of contaminated tailings water is desirable. The cloning of thiocyanate genes in broad host range plasmids under the control of E. coli and At. ferrooxidans promoters and the expression and phenotypic effects in both species will be described.

Jan 1, 2002

By I Brunton

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to MillTM optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions û compressive and tensile. In the first region, compressive stress waves form a æcrushed zoneÆ directly adjacent to the blast hole. The second region, termed the æcracked zoneÆ, occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to MillTM project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the fine to intermediate section (1 mm to 100 mm) of the fragmentation curve. This region of the distribution is important for Mine to MillTM optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split. Following this work, an improved fragmentation model will be developed in response to these findings.

Jan 1, 2001

By R D ROSENTHAL

BHP Iron Ore Ltd's Mt Whaleback is the largest single open-pit iron ore mine in the Pilbara region of Northwestern Western Australia. A division of BHP Minerals, one of three core businesses of Broken Hill Proprietary Company Ltd (BHP), BHP Iron Ore - Newman is a joint venture with minor participants C Itoh Minerals and Mitsui. Mine planning for Mt Whaleback generates detailed sequence plans for a long term forecast incorporating equipment requirements, marketing forecasts, and pit development strategy. Utilisation of several computer packages, both commercially available and site modified, are necessary to achieve such a demanding task.

Jan 1, 1992

This paper will discuss the challenges and opportunities in the years 1998 to 2002 faced by the operation and personnel at Thalanga, and its continued survival through short life projects (three feasibilities in four years). It will describe the processing of the different ores, issues faced and operating and technical innovations that occurred during that period. This will include: commissioning on very high grade Cu ores, treatment of high Sulfur feed ores (~46 per cent S) and the effects of the installation of a Detritor Mill on the process.

Jan 1, 2003

Multi Torque Industries and Jadefoil have developed a safer, more efficient method of explosive protection, retention, placement, and constraint. In particular, this refers to advancements in airbag technology, where the system will offer an alternative to conventional gasbags and decking methods to provide a far more controlled and safer working environment. Airbags have provided operator control and reliability which has not until now been possible in this type of application. The benefits have been noted by current users and the advantages have provided an increase in productivity and significant savings in explosive waste. Obvious problems with gasbags lie in their instability in hot conditions where the danger is associated with gas canisters exploding with great force posing a significant risk to operators. Other problems associated with the decking systems currently on offer is the lack of versatility and operator control. The airbag systems give the operator full control to guarantee accurate placement, assured retention whilst boasting a quick operation of less than a few seconds for conventional void blocking, decking and plugging. One of the main advantages of the airbags is that the operator has full control over placement and retention force, therefore in wetter conditions where slippage can be a problem extra air can be added at the operatorÆs discretion to ensure a sufficient grip. Technical calculations coupled with experimental testing have demonstrated that an airbag will support the weight of a 30 m water column in an 89 mm hole at an initial bag pressure of 5 psig. Applications are increasingly growing whilst more customers embrace their use. Advancements such as the ability to deck in overhead holes, block voids in overhead holes at any depth, explosive retention in very wet conditions, longhole stabilisers to prevent hole closure and concertinaed liners reflect a dynamic potential for new technologies. All of these applications provide a decrease in explosive waste, an increase in operator safety, an increase in explosive protection, and an increase in productivity.

Jan 1, 2004