Search Documents

By C G. Ryan, D R. Cooke

The Thames gold-silver deposits are part of the Hauraki goldfield, situated within the Miocene to Pliocene calc-alkaline Coromandel Volcanic Zone (CVZ). The Waitangi vein system is one of the mineralised ore shoots in the Thames district. The Thames gold deposits are characterised by shallow-level epithermal vein mineralisation with phyllic to advanced argillic alteration assemblages and abundant sulphide minerals including pyrite, arsenopyrite, chalcopyrite, galena and sphalerite. Gold occurs as electrum in association with sulphide minerals. Sulphur isotope analyses of mixed sphalerite-galena and sphalerite-galena-chalcopyrite samples yield a narrow range of δ34 SCDT values (-1.0 to 0.9 ë; n=5), whereas late spongy pyrite gives unusually light sulphur isotope values (-16.7 to -27.9 ë; n=4). Vein quartz from the mineralised zone at Waitangi yields δ18OSMOW values from 6.8 to 12.7 ë (n=23). Fluid inclusion studies indicate a homogenisation temperature range of 190¦ - 296¦C and salinity range of 0.2 - 3.0 wt per cent NaCl equivalent. Similar temperature and salinity ranges have been recorded for the other gold deposits in the Coromandel Peninsula. PIXE (Proton Induced X-ray Emission) analysis revealed that the Waitangi ore fluids have 1090 - 2700 ppm K (average 1600), 145 - 205 ppm Ca (average 180), 80 - 100 ppm Mn (average 90), and 80 - 200 ppm Fe (average 120) but no detectable Cu, Zn, Br, Rb, Sr, Pb and Bi (only one fluid inclusion contains 28 ppm Zn). The sulphur isotopic values of base metal sulphides from Waitangi suggest that the sulphur was derived from a magmatic source (either directly, or by leaching of igneous sulphides). The calculated oxygen isotopic composition of ore fluids is between -2.1 to 3.8 ë at 250¦C and -0.1 - 5.8 ë at 300¦C. Oxygen isotope analyses have revealed significant variations in δ18O values with elevation and gold grades. Zones of gold enrichment coincide with a zone of variable oxygen isotope values at the top of the vein system, where boiling and/or fluid mixing most likely occurred. Mixing of ore fluids with convective ground water is a likely mechanism for gold deposition in a shallow environment for the Waitangi vein system and there is also lack of fluid inclusion evidence (eg liquid-rich and vapour-rich inclusions in the same growth zone) for boiling of ore fluids. Oxygen isotope values varying with gold grades within the Waitangi conduits suggest that δ18O values may be useful in targeting bonanza grade gold mineralisation in epithermal vein systems.

Jan 1, 1999

By Subrahmanyam T. V, Rao V. D

GOLD, the most important and highly coveted valuable metal, is being sought and exploited in almost all the geological environ- ments by the developed, developing and underdeveloped coun- tries of the world. Brazil, one of the five largest countries of the world, has similar geological and lithological environments as of Africa, Australia and Canada and also produces this noble metal. With the recent gold rush in Serra Pelada Hill in Para State of Brazil and the consequent migration of a large number of enter- prises to the Amazon region in search of geological conditions similar to that of Serra Pelada, the status of Brazil in gold produc- tion has been considerably elevated to be among the first five of the world. The principal geological environments or the lithologies where gold can be explored are the greenstone belts, banded iron for- mations, quartz lodes and placers; and the tectonic controls like shear zones in these horizons, or the tectonic relics or the annular- structures that limit the quartz vein systems in felsic as well as volcanogenic systems and epithermal models. The greenstone, BIF associations are present in all the Archean-Proterozoic ter- rains in Central and Northern Brazil. The quartz boudins in Al rich schistose rocks and the weathered and chemically enriched

Jan 1, 1988

A study was conducted to evaluate the effectiveness of the three types of sample grinders routinely used in the mining industry for the sample preparation of gold ores with particular emphasis placed on testing their capacity to produce a representative assay sample of coarse gold ores. The grinders used in this study are the Labtechnics LM5, the Mixermill 4010 ringmill and the Keegor vertical spindle pulveriser, commonly called a Keegormill. The study was based on the preparation of samples from two sources of known coarse gold ore, the Union Reefs Gold Mine and the Brocks Creek Gold Mine in the Pine Creek region of the Northern Territory of Australia, and a fine gold ore which was from the Macraes Gold Mine in New Zealand. The Union Reefs Mine contains visible coarse gold with 30 per cent to 40 per cent of the gold in the plus 75 μm fraction of milled ore. Discreet particles up to 5 mm have been recorded, Hellsten (1994). Union Reefs Gold Mine recovers 40 per cent of its bullion production through a gravity circuit, Riches (1997). Brocks Creek ore contains visible coarse gold with gravity bullion production fluctuating between 50 per cent and 65 per cent, depending on the mill feed. Average gravity bullion production from the Brocks Creek Mine is 55 per cent, Wilke (1997). The average gold grain size of Macraes Mine ore is 20 μm with 40 per cent of the gold in sub 10 μm particles. No gravity bullion is produced from the Macraes Mine, O'Keefe (1997). The testwork demonstrated conclusively that it is possible to prepare a representative sample for assay, of a coarse gold ore, when a Keegormill is used to pulverise the sample to a nominal 100 μm particle size (90 per cent passing a 100 μm screen by wet sieving). Both the Mixermill and the Labtechnics LM5 failed to prepare a representative sample, even when ground to a nominal 75 μm particle size.

Jan 1, 1998

In 1987 the control strategies at the then ZC Mines' New Broken Hill Consolidated concentrator were a miscellaneous mixture of computer hardware and technology for ISA, grinding and residue thickener control. Field instrumentation was based on current-to-air technology of approximately the 1960s. Decisions were made to rationalise computer and field instrumentation technologies; the object being to consolidate control loops into one system to enable expansion of the system to include all facets of plant operation. The first stage was to install a DEC Micro PDP 11/23 computer and serial line communication as recommended by AMDEL Ltd, for the ISA system, as discussed by Walsh and Freeman (1988). The second stage was to select and install a distributed control system for the centralisation of the control loops into one system, and to replace field instrumentation with state-of-the-art technology. This paper deals with the second stage of the rationalisation, in an attempt to give an insight into what is required when personnel are faced with such a decision, details of costs involved in keeping a system functioning and utilised; and the requirement to train personnel for acceptance of further control strategies.

Jan 1, 1991

By G J JAMESON

The flotation cell has undergone a number of changes since the process was first introduced in Broken Hill in the early years of this century. The development of the mechanical flotation cell is reviewed, followed by a discussion of more recent developments such as the flotation column, the air-sparged hydrocyclone, the Wemco-Leeds cell, the Bahr and Deister columns and the Jameson cell.

Jan 1, 1992

By Gillies A. D S

The active history of foreign investment in the mining industry has resulted in Australia emerging as a major world producer of a range of mineral commodities. The current contribution to the national economy represented by mineral production and export revenues would not have occurred without both capital and expertise provided by foreign investors in the past. The initial foreign investment has led to the formation of Australian majority owned and controlled multi-national mining groups such as BHP Limited, CRA Limited and MIM Holdings Limited. These Australian companies, and others, are playing a significant part as foreign investors in the mining industries of Papua New Guinea (PNG) and Indonesia. The study examines issues of importance in foreign investment in each of the countries. It concludes that in Indonesia, the nationalisation of the Dutch mining industry in 1957 did much to deter foreign investment. The remarkable degree of policy stability brought about by the Contract of Works system since 1967 has gone a long way to restoring that confidence. The level of investment in the Indonesian mining sector is steadily increasing. Its attraction to Australian investors is a combination of policy stability, favourable fiscal terms, geological prospectivity for a range of commodities and proximity to Asian markets to the north. PNG has a stable policy regime which until recently has been free from political interference at the administrative level. As such, investors were developing confidence in the system and investment was progressively increasing as evidenced by growing exploration expenditures up to 1988. The 1989 Bougainville revolution caused a re-assessment of PNG's investment and country risk. The recent Mt Kare incident has further raised concerns over the government's ability to guarantee internal security. Foreign investors are faced with weighing concerns with the risks of operation in PNG against the undoubted geological prospectivity of the country. The fiscal regimes of Australia, Indonesia and PNG were compared by means of a simulated open pit gold mine in each country. The effect of taxation is examined by reference to the relative change in project internal rates of return (IRR). The comparison of the relative differences between pre-tax and post-tax IRRs provides a measure of the relative attractiveness of each fiscal regime.

Jan 1, 1994

By C M. Zammit, N Cook, F Reith, C L. Ciobanu, J Brugger

The role of biological agents in the gold mining industry is currently limited to the use of microorganisms in bioleaching and bioremediation. However, there is a variety of possibilities in which biotechnology could aid the mining industry in the future. In this article we discuss the potential for the development of these novel biotechnologies and the role they can play in the exploration for new gold deposits, the processing of ores and the post-mining remediation of sites. The development of these biotechnologies has been enabled by rapid advances in our molecular-level understanding of the role microorganisms play in the solubilisation, dispersion and precipitation of gold. An understanding of the distribution of microbial species in soils overlying mineralisation can be utilised to develop bioindicator systems that assist with gold exploration. An in-depth knowledge of how microorganisms interact with gold complexes is being used to develop in-field biosensors, supporting exploration. Processing technologies may be improved based on advances in our understanding of the interactions between microorganisms, ore minerals, cyanide and gold. For instance, cyanide-producing microorganisms are being investigated for use in in situ leaching of gold. In turn, the use of cyanide-utilising microorganisms for the degradation of cyanide is being explored. Combined, the implementation of these biotechnologies in the gold mining sector may revolutionise the industry, leading to greener, more efficient exploration for and extraction of gold.CITATION:Zammit, C M, Cook, N, Ciobanu, C L, Brugger, J and Reith, F, 2013. Possible future applications of biotechnologies in the gold industry - a prospective approach, in Proceedings World Gold 2013 , pp 233-244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Fawcett M

Pine Creek Goldfields Limited (PCG) is rehabilitating the Enterprise Pit to an aquatic habitat and potential water resource. This paper discusses the development and implementation of that plan. Pine Creek Goldfields Ltd's Enterprise Mine is located approximately 230 km south of Darwin. Open cut mining of the orebody commenced in 1985 and continued for eight years with 14 million m3 of ore and overburden extracted. Geochemical testing of exposed rock types in the pit has demonstrated a propensity to produce acid, and dissolved metals. A plan of management has been developed and implemented to minimise the risk of acid formation and improve the overall water quality in the final void. In developing the plan prime consideration was given to reducing the potential for pit water to impact upon the regional groundwater. An interception system was constructed on Pine Creek to divert approximately 9 km2 of upper catchment into the northern end of the Pit. Construction of the diversion system was completed in December 1993 and a comprehensive surface and groundwater monitoring program initiated. The monitoring program and associated studies are also discussed.

Jan 1, 1994

North Eastern Russia encompasses the northern part of the Circum Pacific. The region comprises various tectonostratigraphic terranes, including cratonic blocks, fragments of volcanic arcs, accretionary wedge terranes, oceanic crust and passive continental margins. The terranes have been accreted to the eastern margin of the Siberian Craton in the Late Mesozoic. The prominent structures of the region are extended zones of the Mesozoic flysch and turbidites. Another important structure is the 3000 km long Okhotsk-Chukotka volcanic arc which marks the Cretaceous active continental margin of northern Eurasia. The youngest structure of the region is the 2000 km long Late Cainozoic Kamchatka-Kuril island arc system. North Eastern Russia is the main gold producing region of the Russian Federation. Since the beginning of recorded gold production in 1932 until 1995 the region has produced 2575 t (83M oz) of gold. Most of it, 2439.5 t, has been produced from placers. Owing to depletion of alluvial gold resources, exploration and mining emphasis is currently switching to the development of the lode deposits. At least five distinct types of the gold mineralisation are reported in North Eastern Russia - mesothermal gold mineralisation in the Mesozoic fold belts, Paleozoic epithermal gold mineralisation occurring within Omolon block, epithermal gold mineralisation related to the Mesozoic volcanics, Cainozoic epithermal gold mineralisation, gold-bearing Cu-porphyry deposits. The current paper introduces the metallogeny of lode-gold deposits of North Eastern Russia. It provides the review of the regional geology, the selected gold provinces and representative deposits with an emphasis on the mineralisation styles and distribution control.

Jan 1, 1999

By D Craw, P V. Angus

Gold mineralisation at Macraes occurs as late quartz-carbonate veins within a body of sheared and hydrothermally altered Otago Schist, the Intrashear Schist. The alteration is characterised by the presence of rutile and the absence of epidote and titanite, indicative of an alteration fluid containing >10 mol per cent CO2. In areas of high strain, a fabric of black microshears develops, gradational to mylonitic cataclasite in the high strain zone adjacent to the hanging wall of the duplex shear zone. The microshears contain hydrothermal graphite, inferred to have been deposited from a methane-rich fluid. The mylonitic cataclasite is characterised by abundant pyrite, the absence of albite and extreme grain size reduction. Gold recovery in the CIL processing plant at Macraes can drop to 50 per cent or lower for some unfavourable ore types. Preg-robbing by a component in the ore, possibly graphite, was suspected as the cause. Mylonitic cataclasite was identified as the lithology responsible for the poor recoveries, with the capacity to bind about 30 ppm of gold in the leach tanks. A program of detailed geochemistry and quantitative grain-size measurement using Coulter analysis was undertaken to identify specific mineralogical factors associated with preg-robbing. The results indicate that pyrite, graphite, and extreme grain-size reduction are the factors associated with highly preg-robbing ores at Macraes. The evolution of the mylonitic cataclasite is accompanied by strong potassium enrichment, as muscovite, and depletion in sodium as albite is removed. This suggests that a simple powder XRD ratio of the albite to illite peaks would suffice to distinguish the preg-robbing ore for grade-control purposes.

Jan 1, 1999

By G E. Smith, G N. Lye

Wall control blasting practices are necessary to reduce the impact of blasting on mine faces but can also have a significant negative impact on mine productivity and operating costs. The conventional practice in deep open pit mines is to use so-called trim blasts adjacent to pit walls. To provide burden relief these trim blasts have fewer rows than full production blasts and are fired to a cleared free-face; hence they are termed æunchokedÆ. This practice leads to scheduling constraints on the pit operations and can cause ore dilution due to excessive muckpile movement. The use of such trim blasts stems from the perception that increased wall damage results from æchokedÆ blasts. These concerns are based on the unproven assumptions that blast vibration levels and explosive gas penetration increase with increased blast burden and face confinement. This paper describes work undertaken as part of a major investigation into wall control blasting at the KCGM Fimiston Mine, Kalgoorlie, Western Australia. It details a study to assess damage effects due to blast burden. Borehole air pressure measurements and borehole video camera inspections were done behind a series of single blastholes drilled with varying burden distances, as well as behind a dedicated trim blast and a full production blast. It was found that the measured damage effects, including visible rock cracking, dilation, and the limited extent of gas penetration behind the blastholes, did not vary significantly with burden or blast type for the cases tested. This result was in complete agreement with detailed vibration measurements conducted by Blair and Armstrong (2001) during the study, which found that vibration was independent of blast burden. As a result of these investigations, changes to the blasting practices at the mine were implemented. Dedicated trim blasts and free-face blasting have been replaced by modified production blasts and the practice of æchokingÆ blasts has been introduced. This has resulted in a significant improvement in productivity and cost savings without compromising pit wall integrity.

Jan 1, 2001

By H Jalalifar, N Aziz

In the ten years since the University of NSW proposed a pillar design methodology for bord and pillar operations, the Australian coal mining industry has changed substantially. What was primarily a bord and pillar design approach is now being applied to chain pillar design in longwall mines where the requirements are substantially different. The dimensions of chain pillars can impact on tailgate conditions (roof, rib and floor), seal performance, and surface subsidence. The status of chain pillar design practice in Australia is reviewed, with a focus on defining pillar strength, chain pillar loading, and assessing the performance of the roof/pillar/system. A new pillar strength equation is proposed for Australian coal that applies for all width/height ratios. An alternative analysis of probability of failure of chain pillars is presented.

Jan 1, 2005

By A Yame, P J. Pollard, E Atase, J Garu, M Tangwari, D R. Hastings, R W. Smillie

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Townsville prospect is situated approximately 4 km north of the Ok Tedi copper-gold mine in Western Province, Papua New Guinea. Drilling in the 1990s delineated a resource of >1 Moz of gold within shallow, skarn breccia-hosted mineralisation associated with quartz-carbonate infill, together with pyrite, chalcopyrite, pyrrhotite, sphalerite, galena, tennantite-tetrahedrite, arsenopyrite, marcasite, and a variety of Au-, Ag- and Bi-telluride minerals. The deepest of these historical holes (TVL034) also intersected copper-gold-silver mineralisation more than 100 m below the gold-rich zone that is associated with calc-silicate skarn breccia. Although copper-gold-silver mineralisation in DDHTVL034 is associated with clinopyroxene-rich skarn, it was also noted that garnet in the skarn breccia became progressively darker in colour with depth, ranging from green at shallow levels to dark red-brown at depth. This indicated that the skarn breccia is zoned, with more proximal garnet skarn at depth possibly indicating an association with porphyry-style copper-gold mineralisation.Based on this skarn zonation model, recent drilling at the Titan prospect, located approximately 500 m south of TVL034, was targeted at potential copper-gold silver mineralisation beneath shallow skarn breccia-hosted gold mineralisation. DDHTVL 081 intersected 46 m at 6.36 g/t Au from 68 m and 80.7 m and 1.67 per cent Cu, 1.27 g/t Au and 20.32 g/t Ag from 184 m. Exploration is now attempting to define the extent of copper-gold-silver mineralisation by defining structural controls on the skarn breccia together with paragenetic and mineral zoning data.CITATION:Smillie, R W, Pollard, P J, Hastings, D R, Yame, A, Tangwari, M, Garu, J and Atase, E, 2015. Exploration of the Townsville Cu-Au-Ag skarn, western province, Papua New Guinea – preliminary observations of paragenesis and zoning, in Proceedings PACRIM 2015 Congress, pp 593–600 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By N Steenkamp, L Furstenberg, W Cele, M Richter

Managing productivity and improving efficiency for a healthy return on capital employed have become key mining industry strategies under prevailing tough global market conditions. However, achieving this in a multisystem environment such as a mining operation can be daunting. The field of discrete event simulation offers some relief, giving engineering teams insight into multivariable systems and stochastic processes. It allows for integrated system thinking and domain expertise to be woven into project thinking fibre. Directed system optimisation and therefore improved efficiency becomes possible. Furthermore, capital discipline accrues from optimal upgrade investments. This paper illustrates the practical application of this approach by reviewing a typical case study for a direct shipping iron ore operation. Dynamic simulation was used to establish maximum processing plant capacity under varying material characteristics and identify capital-efficient upgrades for increasing production.The study started with descriptive statistical analysis of existing data. Discrete equipment and system capacities were defined, followed by static plant mass balance calculations to establish bottlenecks and overall static capacity. Equipment ‘uptime’ and ‘downtime’ analyses established system and overall plant availability and utilisation. From this information, a dynamic simulation model could then be developed and initially calibrated against actual plant performance to verify its robustness. Once confirmed to accurately represent existing plant dynamics, system capacity response to variable changes could be tested to ultimately determine maximum plant capacity. Additionally, plant optimisation was incorporated to arrive at optimal upgrade points. Maximum capacity and necessary upgrades were established as a function primarily of feed size distribution. Additionally, the interfacing effects of rehandling feed material to the final product grade and potentially to life-of-mine were established as important outcomes. The results of the study illustrate the value of using dynamic simulation models to realistically and cost-effectively increase throughput.CITATION:Cele, W, Furstenberg, L, Richter, M and Steenkamp, N, 2015. Capacity evaluation of iron ore processing facilities utilising dynamic simulations, in Proceedings Iron Ore 2015, pp 597–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

For the mineral industry, sustainability seems to mean socially positive and ecologically neutral mineral extraction. Mines are financed and developed in response to demand for their products. The purpose of my paper is to indicate the potential dimension of demand. As part of an unrelated study which I undertook ten years ago, it became apparent that there is a persistent relationship within communities between infant mortality and mineral use; greater mineral use corresponds to a lower rate of infant mortality. This comes as no surprise; sufficient potable water, a reliable supply of food, hygienic waste disposal, hot water and refrigeration all improve the chances of survival of the more vulnerable members of any community. The predictable provision of these facilities requires the application of minerals. This relationship is supported by a table (Appendix 1) included in the UNICEF publication, æThe State of the WorldÆs Children 2001Æ. This table lists regional infant mortality rate (IMR) statistics from around the world, including a listing for æindustrialised countriesÆ. Such countries experience an IMR lower by an order of magnitude than any other region. æIndustrialisedÆ inevitably involves the use of metallic and energy minerals. The principal use of copper is in the generation and distribution of power; it is fundamental to any industrialisation. IMR is a valuable connection because it quantifies caring for the young, a vital strategic driver of human behaviour independent of time, place, fashion or economic circumstances. I have tabulated the population, IMR and the copper demand per head of population for countries containing over 99 per cent of the population of the world in the years 1950, 1960, 1970, 1980, 1989, and 1999. These countries have been consolidated into four groups, Very High, High, Medium and Low rates of infant mortality (UNICEF has used this terminology; the Low group includes all the æindustrialised countriesÆ). The purpose of this consolidation was to reduce the volume of work, to dampen out the impact of regional wars and business cycles, and to dampen out the variable quality of information. Based on the pattern of the copper demand, population and IMR over the last 50 years, I have projected the likely copper demand in 50 years time. A dominant feature of my tabulation is the increase per decade in copper use per head and a corresponding reduction of the IMR. The word æuseÆ is preferred to æconsumptionÆ because it is estimated that over 80 per cent of all the copper ever mined is still in circulation There are two major influences at work; one is the absolute increase in population (UN estimates for 2050 are updated periodically) and the second is the movement of countries into a higher pattern of use and lower IMR. For example the Medium group in 1989 had an infant mortality rate approximating that of the Low group in 1960. With the population of the Medium group (which includes Russia and China) forecast to reach 2.6 billion in 2050, the world copper demand in that year will be significantly greater than the present figure. Nevertheless it will not be as great relatively as the increase of over 300 per cent in the last 50 years.

Jan 1, 2002

By J Zhou, X Bi, Y Yan, W Peng, H Yang, D Weng, P Li

Fortescue Metals Group (FMG) fines from Western Australia is a hematite and limonite mix characterised by high crystal water content. Due to its higher supply capacity and lower prices, the Wuhan Iron and Steel Corporation (Group) intended to use more FMG fines in the sinter mix. It is understood that sinter quality is closely related to its microstructure featured by the hardness and brittleness of different mineral phases, the content of micro pores, and trans-cracks. In order to maintain sinter qualities such as tumble index, reducibility and so on at higher FMG fines blend ratios, a research project was initiated to study the effects of the FMG fines blending ratio on sinter microstructure. Research results showed that at higher FMG fines ratios, the hardness of hematite and magnetite were both decreased while the hardness of calcium ferrite showed a tendency to decrease. The number of cracks that were generated during Vickers hardness measurement in various mineral phases decreased, but their length was shortened, and the variation of crack lengths increased. The contents of hematite and magnetite were also reduced and the reduction of magnetite was clearer. Also the content of calcium ferrite and pores rose and the magnitude of the increase of pores was greater. Among all the mineral phases in sinter cakes, the Vickers hardness of hematite was highest within the range of 879 N/mm2 ~ 942 N/mm2, and therefore the decrease of its content in sinter and the enhancement of its brittleness, ie the number of cracks increased, were harmful to sinter strength. In addition, the excessive increase in pores content is also not favourable to sinter strength.CITATION:Bi, X, Yan, Y, Zhou, J, Peng, W, Li, P, Yang, H and Weng, D, 2013. Study of sinter microstructure with various blend ratios of Fortescue Metals Group fines, in Proceedings Iron Ore 2013 , pp 331-336 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

The Goonumbla district of central-west New South Wales, Australia, hosts four significant porphyry Cu-Au deposits that contain a combined probable ore reserve of 71.7 million tonnes at 1.2 per cent Cu and 0.5 g/t Au. Mineralisation in the Goonumbla deposits is associated with narrow, pipe-like intrusions of quartz monzonite porphyry, in which several intrusive phases have been recognised. Five textural characteristics have been used to distinguish the various intrusive phases recognised in the Goonumbla porphyry deposits: (1) phenocryst abundance; (2) nature of the groundmass; (3 and 4) proportion and mineralogy of the mafic and non-mafic phenocrysts; and (5) the presence or absence of anhedral quartz grains in the groundmass. In addition, each intrusive phase is classified according to its estimated original quartz, alkali feldspar and plagioclase contents. Features common to all of the intrusions are that they contain two types of plagioclase and two or three types of K-feldspar phenocrysts in variable proportions. Most of the intrusions also contain apatite micro-phenocrysts. The groundmass textures range from aphanitic through granular to euhedral K-feldspar in a quartz matrix. With only one exception, all of the intrusive phases recognised are either quartz monzonite porphyry or mafic (>5 per cent mafic minerals) quartz monzonite porphyry. The exception is a biotite - phyric monzodiorite, which occurs in the basal portions of one of the deposits. Textural variants of intrusive phases at Goonumbla have been investigated to establish whether specific combinations of characteristics indicate mineralised intrusions, while others suggest barren ones. Some correlations between intrusion types and Cu and Au grade have been recognised. The most important textural characteristic that relates to high grade mineralisation appears to be the low proportion of mafic minerals, because the quartz monzonite porphyry intrusions hosting most of the mineralisation in the two deposits studied contain

Jan 1, 1999

By K Gottliebsen

Many hydrometallurgical and chemical processes produce large amounts of acid waste. This is illustrated by the copper S/X-E/W process used at the Mount Gordon mine in North Queensland, which produces a tank house bleed in the form of a concentrated sulphuric acid stream. The bleed stream is necessary to remove impurities such as iron that decrease the efficiency of the electrowinning process. However, this bleed stream comes at a high financial cost due to large quantities of make up sulphuric acid required as well as the need to neutralise the bleed stream prior to disposal. The present work describes the approach taken to develop a solvent extraction process for the selective recovery of sulphuric acid from copper tank house bleed liquor. The proposed extraction system was investigated using a branched long chain aliphatic tertiary amine tris(2-ethylhexyl)amine (TEHA) as the extractant, Shellsol 2046 as the diluent and octanol as a modifier. Computer simulations were used to determine the optimum operating conditions for the recovery process. It was found that the process was able to selectively recover up to 90 per cent of the sulphuric acid from the copper electrolyte. This is recovered as a pure aqueous acid stream at a concentration of up to 130 g/L that can be recycled back into the tank house circuit or other areas of the process. The raffinate acid concentration was reduced from 180 g/L to as low as 18 g/L, significantly reducing waste disposal and the environmental impact of the copper process. The equilibrium data and simulation results were also compared with an alternative extractant, CYANEXR 923. Finally the efficiency of the TEHA extraction system was investigated on a pilot-scale in a pulsed perforated plate column. This information was used in order to scale the process for an industrial application. The same methodology applied in this case study could be used to provide innovative and cost-effective solutions to waste streams encountered in other hydrometallurgical or chemical processes.

Jan 1, 2000

Delivered by K. B. Gross at the First Ordinary Meeting of the Australasian Institute of Mining and Metallurgy, August 18th, 1952.Mr. President, Ladies and Gentlemen:Confronted with the task of reviewing the progress of Mount Isa Mines Limited, since the inception of the Company 28 years ago, I soon found that effective coverage was a task beyohd me, if I were to confine the address within the limits of time allowable. Faced with the alternative, a summary, that could only fail to -do justice to the subject, I turned elsewherl? for inspiration and found it in Chester Wilmot's book "The Struggle for Europe". Those of you who have read this masterly contribution to the literature of World War II will recall that he takes us, most dramatically, behind the scenes and we learn of the thoughts and ideas that were uppermost in the minds of both allied and enemy leaders at times when decision's that profoundly influenced the course of the war were taken. I felt I could safely follow this rather novel approach to my own problem. Strengthened by the realisation that the technical achievements of the Company have largely been covered over the years, and that the results of our labours are mainly here before you, I have attempted to liven up my modest canvas by going behind the scenes, and have sought to deal with ideas and the reasons for important decisions, rather. than to embark upon a purely descriptive essay.If then, you will bear with me, we shall skip back through the years to the days of struggle that our President's address has so aptly covered, and find that one man's ideas and faith stand out beyond all others. W. H. Corbould must always be credited with having founded the enterprise, for he correctly appraised the potential of the struggling prospect and foresaw what could be done, despite the handicaps of geography, climate and need for heavy expenditure.

Jan 1, 1953

Upgrading of Indonesia's Bauxite by Washing Method There were eight bauxite samples used in this research, three samples from Kijang contain total SiO2 18.36 - 29.16 per cent, Al2O3 40.12 - 48.36 per cent, Fe2O3 4.27 - 5.13 per cent, one sample from Tayan, contains total SiO2 4.69 per cent, Al2O3 38.95 per cent, and Fe2O3 19.67 per cent, and four samples from Mempawah contain total SiO2 33.5 - 44.8 per cent, Al2O3 29.8 - 35.9 per cent, Fe2O3 7.29 - 9.88 per cent. All of those bauxite ores have not fulfilled the requirement for Bayer process yet; therefore simple up-grading using a rotary drum scrubber is needed. The scrubbing process was carried out with time variable up to 60 minutes with solid percentage applied was 50 per cent and rotary speed was set up 30 rev/min. The bauxite was washed by following steps: scrubbing, screening, drying, and finally it was analysed to show chemical content. The washed bauxite produced has size fraction that is retained on the 1.7 mm of screen opening. The result of the research shows that the higher alumina content of the raw bauxite, the longer washing time is needed moreover the higher quality of the washed bauxite is produced. The highest alumina content of the washed bauxite was 53.67 per cent with the alumina recovery was 89.66 per cent and the concentration ratio of 84.80 per cent was achieved within 20 minutes of washing time of the raw bauxite (Al2O3 48.36 per cent). The washed bauxite resulted from this research is suitable as a raw material for Bayer process.

Sep 13, 2010