Search Documents

By Schon RW, Stephens CJ

The Whitsunday Volcanics occupy most of the offshore islands from the Whitsunday Group, southeastwards through the Cumberland and Northumberland Groups, possibly extending to the mainland adjacent to Shoalwater Bay, a distance of 370 km. Some of the islands of this group are granitic, but preliminary Rb-Sr data indicate these to represent Permo-Triassic basement. Cretaceous volcanism is interpreted to have occurred during initial rifting prior to the continental breakup of northeastern Australia and subsequent development of the Tasman Basin.The volcanics comprise mainly lithic ignimbrites, with local development of inter-bedded surge and bedded tuff, accretionary lapilli tuffs, lithic concentration zones, and lag deposits. Isolated fluidual rhyolite and dacite domes occur. The deposits are considered subaerially emplaced. A Rb-Sr isochron age for volcanism of 110 Ma is determined from new data. The total thickness of the volcanics is unknown, but a minimum thickness of 4-5 km on Whitsunday Is. is suggested. Eruptive centres are inferred to be distributed throughout the volcanic zone. The volcanics are cut by numerous, dominantly near N-S, dykes ranging from dolerite through to rhyolite in composition.Chemically, the volcanics and dykes exhibit a continuous range of compositions from basaltic andesite, through andesite, dacite, to rhyolite, with minor more alkalic compositions. Phenocryst mineralogy in the silicic rocks is mainly plagioclase, augite, and Fe-Ti oxides, with less frequent quartz and hornblende occurrence. Sr and Nd isoptic compositions for volcanics and dykes are close to mantle values. These data are tentatively interpreted in terms of a lower crustal magma arc source separated from the mantle only a geologically short time prior to Cretaceous magmatism.

Jan 1, 1990

By Soma T

Pyrite and Cu-concentrate were roasted in vertically suspended state in an externally heated tube. Tubes of three different lengths of reaction zone were used for three different reaction times. Roasted ores were submitted to chemical analysis and the extent of roasting reactions was determined. In case of pyrite, extent of roasting reactions was not affected much by reactor length and heating temperature (above 500¦C), but was considerably by ore/air ratio. Micro- scopic and XMA examinations led to the conclus- ion that pyrite particles decomposed to pyrrho- tite and then pyrrhotite was oxidized to give Fe-S-0 melt, magnetite and hematite. The extent of reaction was not uniform in all particles but had a wide distribution from unreacted pyrite to completely oxidized particles. Combustion of Cu-concentrate from Kuroko complex sulfide ore ) was unstable under a uniform wall temperature of 450¦C, but proceed- ed rapidly at temperatures above 500¦C. Sticking of roasted ores to the wall of the reaction tube induced choking of the tube, caused by melting of roasted ores, at tempera- tures above 950¦C. Enrichment of oxygen exterted less influence on reaction rate than heating temperature of the tube. Particle size of ore had a big effect on reaction rate.

Jan 1, 1980

By Vernon PN

The Eossing Uranium Mine is a high tonnage low grade open pit operation using acid leaching for uranium extraction and ion exchange and solvent extraction for solution purification. Advanced technology, much of it computer based, has led to major economies that have contained operating unit costs over the last four years in the face of double figure inflation. An improved ore reserve block model and mine planning system have achieved a considerable reduction in the stripping ratio. Drilling and blasting costs have decreased some 25%, mainly by the introduction of heavy ANFO explosive. A centralised computer control centre for the metallurgical plant has increased labour productivity resulting in improved process control. The all-staff workforce is united with management in the objectives of creating a safe, healthy, working and living environment and a prosperous company, capable of contributing to the wellbeing of the nation and the shareholders. This situation has been brought into being by an equal opportunity policy coupled with a management system emphasising open two-way communication through all levels in the organisation. The success of this policy is highly apparent in the morale and productivity of the workforce.

Jan 1, 1986

By Kavetsky A, Scott A

As well as breaking and moving rock, blast energy sets up a seismic wave in the ground which can cause significant damage to rock structures and buildings and disturbance to human occupants. This seismic ground vibration is potentially most damaging when its dominant frequency coincides with the resonant frequency of a structure, leading to high amplification factors between the input ground vibration and the resulting structural response. This paper outlines methods of identifying the resonant frequency of structures. It also describes a practical numerical method for the modification of blast designs to reduce the ground vibration energy in critical frequency ranges. The method is illustrated with two recent case studies.

Jan 1, 1990

By Lawson F

Narrowly sized samples of synthetic chalcocite (Cu2S) and covellite (CuS) were leached in oxygenated acidic sulphate-chloride solutions. Chalcocite leaches via a two-stage process, the first stage being much more rapid than the second. The apparent activation energies are 42.7 kJ/mol and 68.2 kJ/mol respectively, indicating that both stages are controlled by surface chemical reactions. The leaching of covellite is also chemically rate limited with an apparent activation energy of 77.0 kJ/mol. The shrinking core model is able to be used to describe the leaching processes of both copper sulphides. Over 97% of copper present in chalcocite dissolved in 0.5 M H2SO4i0.5 M NaCl solution under one atmosphere pressure of oxygen at 85¦C in three hours from particles 36 pm in diameter while only 85% of the contained copper in covellite particles 13 pm in diameter dissolved in the same solution under the same pressure at 90¦C in six hours. About 99% of the sulphide sulphur in chalcocite was oxidised to elemental sulphur while only 90% of sulphide sulphur was converted to elemental sulphur during covellite leaching. The mechanism proposed for the two-stage leaching of chalcocite particles is as follows: in the first stage, cuprous ions rapidly diffuse to the external reaction surface where they lose electrons and go into solution as a complex cupric chloride ion CuCl'. The second leaching stage begins when covellite is formed at the external surface. Copper again goes into solution as the CuCl* ion. The mechanism for leaching synthetic covellite is similar to the second leaching stage for chalcocite except that the leaching rate of synthetic covellite is substantially lower than that of the newly formed 'covellite'. Elemental sulphur formed on the particle surface retards the dissolution processes during both chalcocite and covellite leaching. The presence of chloride ions is necessary if essentially all of the copper from chalcocite is to go into solution. When no chloride ions were present, the leaching rate of both newly formed and synthetic covellite was almost zero. The main role of chloride ions in both chalcocite and covellite leaching appears to be to disrupt the passivation film of sulphur on the particle surface.

Jan 1, 1989

The Prospero orebody is a part of the Helene mine at Cosmos and was scheduled to begin production in March 2008 after the exhaustion of the Tapinos orebody in the same mine. Treatment of the Tapinos orebody was challenging and it was envisaged that Prospero would have similar properties given that it was also anomalous in deleterious elements and would be of a similar mineral hosting. It was deemed necessary to undertake a metallurgical test work program to identify any potential processing issues, complex mineralogy or significant metallurgical domains. The paper discusses the processes which were employed to undertake the metallurgical test work program and describes the aspects that can be employed by other developers to quickly and effectively assess potential future orebodies. It will demonstrate that the work was successful at determining expected metallurgical behaviour, providing direction for mining operations and highlighting areas for more extensive research.

Jan 1, 2009

Adsorption isotherms, zeta potential and coagulation techniques have been used to exa- mine the mechanism of metal activation on SiO2 and ZnS surfaces. The importance of surface nucleation or precipitation of metal hydroxide coatings is'established and identified-by characteristic charge reversal patterns. The significance of surface coatings in sulphide and non-sulphide flotation is discussed.

Jan 1, 1973

This paper presents a method for estimating the strength and stability of model coal pillars with bedding planes (weakness planes) inclination. The strength of coal relative to the angular difference between the principal stress direction and bedding planes is considered. The failure behaviour of model coal pillars containing weakness plane inclination by using servo-control Schenck Machine are shown. Uniaxial and triaxial compressive strength of coal specimens are investigated, and test results indicated that the strength of coal pillars depends on the weakness planes inclination with respect to the principal stress direction. However, it is shown that with increasing confining pressure, the effect of weakness planes inclination on the strength of the coal specimens is reduced. An empirical method is given for prediction the compressive strength of coal containing weakness planes inclination. The results of this method are compared with the experimental results and Jaeger theory. Finally, three well-known empirical strength criteria were tested against the triaxial test data for coal containing weakness planes inclination.

Jan 1, 1995

By Sheng X. L

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts. collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger..

Jan 1, 1992

By Carrucan M. J

Costain Resources Limited operates two open cut coal mines in the Hunter Valley coalfields of New South Wales, Ravensworth Mine and Warkworth Mine. The location of the Ravensworth operation is shown in Figure 1. In the case of the Ravensworth Mine, Costain Australia is essentially a contract miner and is contracted to supply coal to Pacific Power (previously The Electricity Commission of New South Wales), on contracts won through a tender system. Due to the existing infrastructure and the lease area that associated with the contract, the mining strips at Ravensworth South have a maximum strike length of 1500 metres. This paper deals with the methods of scheduling used to overcome the challenge of mining the short strike length, multi-seam deposit at Ravensworth South.

Jan 1, 1992

Over the past 12 years screening of materials has undergone a dramatic change in both the types and materials used in screen mats and the quality requirements of the finished product. With the main thrust now on quality and a cleaner product a different approach was needed in the operation of sizing screens. New screen mats with many different aperture configurations have been developed using rubber and plastics.to replace the traditional screen mat of woven wire or punched plate.

Jan 1, 1984

A simulation program has been developed tc predict the airflow distribution and thermal environment in multi-level narrow lode Cornish =n mines. Because of the approximate equality between fan power and natural ventilation _rergy a true thermodynamic mesh balance using mass flow rather than volume flow rate was required. Compressibility is allowed for by calculating mesh corrections on a mass flow of dry air basis. In this context, and within the confines of any steady state model, both the steady flow energy and pressure equations are satisfied with equal validity. The mesh balance includes natural ventilation energy, frictional losses, moisture lift work, water droplet energy and fan energy.

Jan 1, 1988

Sampling criteria and practical implementation of these criteria are discussed with a view of achieving and maintaining a high level of quality for minerals at their various stages of production through to their utilisation. From this it will be shown the advantages that can be gained by producers who undertake stringent quality control programmes for their ores, thus ensuring they have a competitive edge over other producers.

Jan 1, 1985

By Weining L

In-situ experiments were performed in a tunnel built in loess soil with the displace- ment components of the tunnel lining and the acceleration components of the tracks measured during the passing of trains. The measured parameters were then studied by the spectral method. As a result, the dynamic forces of trains was simulated numerically and a deter- ministic dynamic nonlinear analysis was carried out by means of finite element method. The results obtained by two different approaches were in fair coincidence. Results of the study indicate, that the low and medium frequency components of the dynamic train loading would be crucial for the dynamic responses of the tunnel lining and surrounding mass, and their effects would increase with the speed of passing trains within a certain range.

Jan 1, 1987

The incidence of colliery disasters has highlighted the need for more centralised and directed coal mining safety research in Queensland, with particular impetus from explosions at Box Flat in 1972, Kianga in 1975 and Moura No 4 in 1986. Inquiries which identified the likely causes recommended measures and, research and two outcomes have been the present Mines Safety Research Advisory Committee and The Safety in Mines Testing and Research Station at Redbank, near Brisbane, dealing with all mining problems, coal and metalliferous. Already, important research into ignition and explosion and other health and safety matters has been accomplished; the Station has become an accredited testing laboratory; and international recognition has been achieved. Now the advisory, testing and research arms are soundly in place to pursue preventive investigations and be ready to provide assistance in any emergencies.

Jan 1, 1991

By Sullivan T. D, Lohe E. M

Geological structure is one of the main controls on ground conditions within mining. It has a significant impact on the mining conditions and productivity of coal mines within the Sydney - Bowen Basin. The three main types of faults common to this region, normal, reverse and strike-slip systems, each present distinct challenges to mining. These systems effect a wide range of geotechnical and mining conditions within the mines. These include coal quality, strata stability, goat and caving behaviour, productivity and maintenance schedules of mining equipment, mine design and mine-site stress fields. A better understanding of the regional, local and mine-scale structural setting, timing relationships of structural events and the mechanisms of fault formation will greatly aid industry's push for greater productivity and competitiveness.

Jan 1, 1991

By Quinlan M. J, Ratcliffe J. S

Chemical kinetics is a dependent process which usually correlates the rate at which a reaction proceeds with the mechanism descriptive of the manner by which reactive particles interact. Given the latter, the object gen- erally is to find the reaction rate dependency in terms of an intensive property of the system - number of reactive particles present, and of the energetics of the system - usually temperature. Chemical kinetics depend on a dem- onstration that reaction considerations alone control the phenomenological process under study. For these rea- sons, chemical kinetics are usually involved in homogeneous gaseous systems. Even in liquid homogeneous sys- tems earliness or lateness of reactant mixing rather than chemical kinetics may be controlling. Considerations of transport phenomena are involved in heterogeneous systems and often control the observable rate:an additional problem in such systems is to apportion the rate due to mass transfer - usually a linear process - and that due to reaction which may be linear or non-linear. Experimentally, conditions are often chosen so that only one consideration controls but this becomes more difficult where solid phases are involved. Kinetic modelling involves considerations of chemical kinetics, transport phenomena, and factors attributable to the physical environment in which the process takes place. The latter two considerations may be quite different as between experiment and plant. The kinetic model may be a mathematical representation of a conceptual mech- anistic model of the reaction. Alternatively, it may be an empirical relationship resulting from, for example, some curve fitting procedure applied to experimental data. The latter approach may be necessary where the system is particularly complicated.

Jan 1, 1975

By Adamiak Z. P, Nicol S. K

An exploratory study has been carried out on the applicability of pre-nucleated feed in pelletising operations. Measurements of the pellet quality parameters showed that iron ore pellets prepared in the above manner, generally meet the specifications required in international pellet traffic. Several potential economic advantages, such as reduced grinding power requirements, increased line productivity and shorter start-up periods, became apparent during the study.

Jan 1, 1974

Automatic sampling and weighing of copper sulphide concentrate produced on Bougainville Island (PNG) is described. Contained metal weights gave satisfactory agreement with buyer's results after the introduction of polyethylene lined sealed aluminium foil bags for transport and storage of assay samples. Paper bags used previously for this purpose permitted oxidation of the sulphide concentrate and thus caused lower assay values.

Jan 1, 1976

By Whitford DJ

A distinct zonation occurs in the nature of submarine volcanic activity associated with westwards propagation of the Woodlark spreading system into continental crust. Olivine tholeiites (Type I MORB) flooring one spreading segment in the Eastern Sector of the Western Woodlark Basin are accompanied by more evolved "ferrobasalts". Basaltic andesites and Mg-poor andesite-dacites occur on axial and flanking seamounts respectively. In the Western Sector, Mg- and K-rich olivine andesites occur in a rift valley and on an axial seamount near the tip of the propMr/8 tig rift. Observed correlations between 6Sr ratios (0.7028-0.7041), REE patterns and K contents imply a complex petro- genesis with the relative importance of mantle heterogeneity and crustal contamination difficult to resolve.

Jan 1, 1987