Search Documents

By D Macfarlane, T McMorran

  This paper describes the design and construction of the upper section of the Pike River Mine Access Road. The road extends 11 km from Logburn Road alongside Big River on the West Coast of the South Island of New Zealand up Pike Stream to the new mine portal on White Knight Stream (Figure 1). This new road starts on alluvial terraces, then partially follows an old logging road before entering virgin bush and traversing the true left bank of a steep sided gorge on Pike Stream some 50 - 100 m above the stream before dropping down to the mine entrance. Its development has been an extended process from route selection, consenting through to design and construction.   The paper focuses on the 1 km section of road between the Amenities Area (Figure 1) and the portal. This section of road is a steep section through the gorge, principally on Conservation estate, and has presented the most challenges and required the greatest effort to obtain the regulatory approvals, prepare the design and to construct. This paper outlines the history of the challenges faced and how the road was successfully developed.

Jan 1, 2007

By Drain P, Dibdin T. R

THE completion of the Linda incline man and supply haft at the Mount Morgan Gold Mining Oompany's mine led to an investigation of the various safety gears in general use in mining shafts. One of these gears completely fulfilled the necessaryconditions. This paper endeavours to give a description of the man car and safety gears now operating in the before mentioned shaft, together with the main considerations leading to their design and sub equent adoption. Fig 1 diagramatically shows a longitudinal section of this shaft.

Jan 1, 1911

The late 1960's and 1970's saw the initial development of the coal resources of the Bowen Basin of Queensland. The projects developed relied on large scale, open-cut operations using draglines for overburden removal and, in the majority of cases, project viability could be established based solely on those open-cut operations. Many of the mines developed in the 1980's have the same characteristics.Unlike these mines, the German Creek Mine has limited open-cut reserves at low overburden to coal ratios, and planning of the complex involved a large open-cut mine capable of developing early cash flow, with phased introduction of underground mining to replace open-cut capacity as the strip ratio increased.

Jan 1, 1985

The physical phenomena which influence gas flow in the bosh and hearth of a blast furnace are discussed including the hold-up of slag as a mechanism which can result in a flooding condition. An equation is defined which describes the limitation to wind volume arising from the flooding condition. Implications of the various factors influencing bosh and hearth gas flow on furnace operation are discussed. Coke quality is shown to be the most important factor in the aerodynamics of these zones and coke requirements are defined for the Port Kembla No. 5 BF which has an inner volume of 2670 m3.

Jan 1, 1975

The phosphatic overburden of Christmas Island is a lateritic soil and consists dominantly of crandallite and millisite. These minerals are polymorphs of general formula, (Na,K)x Ca2-x (Al, Fe)6 (PO4)4 (OH)10-x (2+x) H2O. Iron occurs only in millisite. Both minerals exhibit similar thermal transformations, dehydroxylating near 600¦C and recrystallizing above 800¦C. Dehydroxylation results in crystal structure collapse but retention of crystal morphology. Ggethite, boehmite and apatite are minor constituents of some-of the phosphatic Soils.

Jan 1, 1971

By Clarke RG

Renison Mine was developed as the first all diesel mine in Australia. The foresight of the early planners in committing the Mine to Decline access has paid dividends in the past two decades with Renison Mine establishing itself as one of the most productive underground mines in the world. The excellent productivity has also resulted from the development of mining equipment technology, both on the part of the equipment suppliers and through the coordination of the Mining, Automotive and Technical Design Sections at Renison Mine. Constant improvements in truck and loader design, the design of specific equipment to carry out specialized tasks such as installation of services, scaling and ground support and the conversion to electrically powered equipment have been ongoing at Renison. Currently, larger scale trucks are being investigated for ore and waste haulage due to increased haulage distances and production requirements. It appears as though an articulated low profile truck of around 50 tonnes capacity may provide the short term solution based on the performance data available.

Jan 1, 1982

By Hatherly P, Holt GE, McNally G

The current methodology for delineating and subsequently evaluating coal reserves is based on the use of vertical drill holes and surface based geophysics/geology. These techniques have three major problems, these being respectively:-a) Vertical drill holes can only provide a small sample of the coal seam and stratigraphy. Therefore the planar variation in coal reserve and environment parameters can only be approximated.b) Although surface based geophysics has had its fair share of success in recent years, there are still environments which have masked the finding of major structures.c) Access to drill sites is difficult at some locations due to mountaineous terrain, standing water and environmental impact.

Jan 1, 1985

By P J. Clark, A W. Fisher, R G. Ford

Site characterisation of subsurface contaminant transport is often hampered by a lack of knowledge of site heterogeneity and temporal variations in hydrogeochemistry. The use of a regional-scale data compilation derived from satellite imaging is discussed with respect to directing design of site characterisation to monitor the fate of a Dense Non-Aqueous Phase Liquid (DNAPL) plume in Nevada. Evaluation of the drainage basin contributing to the groundwater flux into the study site was used to re-assess the site conceptual model and re-direct the characterisation effort. The use of highly resolved measurements of subsurface hydrogeochemistry in space and time were employed to identify the predominant biogeochemical processes controlling arsenic transport during discharge of groundwater into a pond at a site in Massachusetts. Direct-push conductivity measurements coupled with vertically-resolved sampling within the pond and adjoining aquifer demonstrated spatial and temporal variations in dissolved arsenic within groundwater and the pond water column and sediment pore water. Spatial variability was observed over the scale of centimetres to metres, and temporal variations were observed over the scales of days (following storm events) to seasons. Microbially-driven redox processes maintained anoxic conditions in groundwater and at the sediment-water interface (iron and sulfate reduction) and exerted both a direct and indirect influence on arsenic solution speciation and partitioning to surface water sediments.

Jan 1, 2004

By L M. Foster, J R. Kellett, G A. McMah

The Great Artesian Basin (GAB) contains one of the largest reserves of fresh water in the world. The volume in storage is enormous, being estimated at nearly 65 000 million megalitres (ML). Development of this resource, dominantly for the pastoral industry, began in the late-1800s and quickly accelerated. With exploitation of the resource, artesian pressures declined almost as rapidly. This loss of head is a result of the total discharge from the basin and much of this discharge is waste of water. The waste through uncontrolled bores and inefficient distribution systems still amounts to about 75 per cent of all discharge. However, the volume in storage has hardly been depleted. The major concern is the effect of withdrawal on artesian pressures. Due to the size of the Basin, the relatively flat gradients and low permeability, the movement of water through the aquifers is extremely slow and independent of recharge. Hence, the normal concepts of sustainable yield (ie discharge should equal recharge) cannot be applied to the Basin as a whole as travel times do not allow for the effect of recharge to be seen away from the outcrop areas within management timeframes. The large volume in storage, though, can provide an extensive buffer to the impacts of temporary water needs. This effect should be considered when assessing the acceptability of fixed life projects such as mines and the extracted volumes from their operations. Identifying a sustainable yield involves balancing the acceptability of the economic, environmental and social costs with the associated discharge and fall in head, to arrive at an acceptable balance.

Jan 1, 2003

By Hagen G, Uhlig H

In the Federal Republic of Germany the thermal environment in underground coal mines has deteriorated progressively over the past years. The number and capacity of refrigeration plants have increased correspondingly. In recent years high capacity spray coolers have been used in addition to conventional cooling coils.

Jan 1, 1988

By Sowerby BD

The CSIRU Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt'/. in field tests at BHP Stockton Borehole Colliery, NSW. Mineral Control Instrumentation Pty Ltd have been licensed to manufacture the capacitance gauges and have installed five commercial units in the coal industry and other industries. Microwave transmission techniques have an advantage over the under-belt capacitance technique in that they are not sensitive to vertical segregation of moisture in coal on the conveyor belt. A laboratory prototype of a microwave transmission gauge has been constructed and tested. Microwave techniques, based on a measurement of attenuation and phase shift, are under development and are expected to be field tested in 1987. These new techniques will enable a wide range of thickness changes to be accommodated. Capacitance and microwave transmission methods are unsuitable for materials of high electrical conductivity, such as coke. CSIRO is therefore developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutron moisture gauges and it is expected to be field tested in 1987.

Jan 1, 1987

The LeadtZinc Concentrator at Mount lsa treats all the lead-zinc-silver ore from the Mount Isa Mine and some of the ore from the Hilton Mine. This concentrator was commissioned in June 1966 and total lead-zinc-silver ore treatment was transferred from the Mount rsa's original No 1 Concentrator in May 1967. Plant capacity is around 5 x 106 t/y.There have been three phases of major plant modifications since commissioning:1. replacement and upgrading of the flotation section in 1979; 2. upgrading of the crushing plant and installation of a heavy medium hydrocyclone plant in 1983 for ore preconcentration, and; 3. doubling ball milling capacity and a further upgrading of the flotation section in 1992.Other developments have included the installation of flotation columns and Jameson cells.The evolution of milling practice since 1955 has been reported by Davey and Slaughter (1970), Bartrum, Dobrowolski and Schache (1977), Fiedler and Munro (1984) and Espinosa-Gomez el al (1989).Lead concentrate is smelted in Mount Isa while zinc concentrate and bulk concentrate (locally called Low Grade Middlings or LGM) are railed to Townsville and shipped to custom electrolytic zinc plants and ISP smelters.

Jan 1, 1993

Introduction.History of Stope Filling at Mount Isa.The Need for a Systematic Fill Programme.Reasons for Filling.Fill Materials and Tonnages.Rough Mullock Fill.Quantities Readily Available.Fill Pass Development.Stope Preparation.Drainage.Hydraulic Sand Fill.Initial Experiments with Mill Tailings.Surface Layout.Operation Procedure.Underground Pipe Lines.Life of Sand Pipes and Cones.Drainage.Old Tailings Dam Sands.Quantity of Fill Placed.Pillar Tonnages.Conclusion and Acknowledgment.INTRODUCTIONFilling practice outlined in this paper refers exclusively to the Black Star section of the mine. The stope filling necessary early in the life of the Black Rock and portions of the Rio Grande sections is not to be confused with the current filling programme.

Jan 1, 1953

The mining of remnant coal reserves at the Liddell Open Cut is subject to a number of risks. These risks are of both a technical and financial nature. Liddell Open Cut is principally a conventional truck and shovel/loader operation, supplemented by a highwall coal augering operation. There are significant areas of divergence from more conventional operations including working in close proximity to a major dam, working up dip from an operating underground mine, and working through areas where there has previously been underground extraction. In addition the site has major long-term rehabilitation requirements. This paper, rather than concentrating on specific detail of areas of risk, presents the spectrum of geological, design, operational and post-mining risks that accrue to the various areas of activity in this open cut operation. The balance of this paper then provides an outline of the strategies employed by Liddell Coal to manage their potential impact.

Jan 1, 1994

By Mortimer RR

The Weipa bauxite mining operation on the west coast of Cape York currently mines lb million tonnes of crude ore per year from the Andoom and Weipa mines. Andoom ore is trucked up to 4 km to a rail load station and hauled 20 km by train to the Beneficiation Plant. Weipa ore is trucked up to 7 km to the Beneficiation Plant. Increasing haul lengths and production requirements have led to a progression of larger two axle rear dump trucks and currently he intrcducticn of 145-tonne, three axle L t Dm dump trucks. bith the introduction of the Andoom a operation in 1972, the decision was made to use a railway system to haul crude ore from Andoom to Weipa. This system has proved to be successful from both an economical and operational view point. Due to the successful combination of a truck and rail haulage operation in Andoom, future :evelopment of orebodies requiring increased haul distances and increased production tonnages will probably result in extension r>f the railway system to compliment the trucking operation from the mine face.

Jan 1, 1978

By M McGeough

Following the success of calcrete sampling at Challenger, calcrete sampling has been widely adopted as the primary exploration technique for gold exploration, in the Gawler Craton. Calcrete is uniformly distributed over large areas and produces discrete gold anomalies. This allows drilling to focus on specific gold anomalous targets. However, despite widespread use of calcrete sampling, very little is known of the origin of calcrete in the Gawler Craton, and the link between calcrete gold anomalies and primary mineralisation. In an attempt to understand this association Lisa Gibbons recently completed an honours project at the Old Well Prospect approximately 45 km SSE of Tarcoola. Her work is part of a collaboration between CRCLEME, MESA and MIM Exploration. At Old Well, a calcrete anomaly (>10 ppb Au)covers an area approximately 7 km x 2 km with a peak value of 97 ppb Au. The study looked at the regolith as a whole, processes of its formation and nature of mineralisation within it. She was able to combine previous calcrete and drilling results with her own observations. The results from this study highlighted problems in relating surface calcrete anomalies to in situ gold mineralisation.

Jan 1, 1998

By D Feng, G C. Lukey, J S. J, R R. Dagastine

An ongoing challenge in the coal industry is pyrite removal using the flotation method for fine particles. The use of a æseparation in frothÆ (SIF) technique to recover coarse particles of up to a few millimetres in size has presented a potential solution. However the commercial success of SIF is still limited due to the poor understanding of the separation mechanism. The particle floatability in SIF is determined by the constructive or destructive stresses resulting from the forces exerted by the particle on the bubble films. Hence, the surfactant properties and the mineral characteristics (eg hydrophobicity, shape, etc) are the key factors that control the interaction between the particle and froth. In the present work, the interaction forces between different particles (ie crushed glass, pyrite and coal) and a single air bubble are measured in a non-ionic surfactant solution (pentaethylene glycol mono n-dodecyl ether, C12E5) using an atomic force microscope (AFM). Experimental results show that the interaction is primarily dependent on the contact angle (ie the degree of hydrophobicity of the minerals). For crushed glass, the transition from repulsion to attraction was observed as the contact angle increased. As the concentration of C12E5 increased, the adhesion force was suppressed due to wrapping effect. For coal and pyrite with much higher hydrophobicity, long-range attraction was observed. The effect of shape factor was only visible at high surfactant coverage where sign of destabilisation became noticeable on the retracting force curve. These results provide a fundamental understanding of the direct interaction forces of a complex real system between an irregular particle of either crushed glass, pyrite or coal and a single air bubble. Theories developed for interpretation and modelling are thus far based upon the study of ideal systems of glass or polystyrene spheres and an air bubble and were incapable of explaining the interactions in complex real systems. The presented measurements were a first approach to the problem of real mineral-bubble interaction in flotation systems. Thus, the results can only best be interpreted semi-quantitatively.

Jan 1, 2005

In reviewing recent developments in the process mineralogy of gold it is convenient to distinguish between visible (>0.1 pm) and invisible gold (1 - 2 pm in size in polished section; these can scan the surface of a polished section, identifying the gold minerals, recording co-ordinates of the grains for subsequent examination, and making measurements of areas and sizes of the grains. However, problems of sample reliresentivity in polished section mean that such data may not give good quantification of gold mineral proportions and liberation/locking characteristics and other methods are required for this (amalgamation, cyanidation, ultra-fine milling and cyanidation). Characterisation of invisible gold in bulk material (eg a sulphide concentrate) can be done by mineral separation, ultra-fine milling and cyanidation or by quantitative point analyses of a large number of mineral grains. Analytical methods include electron microprobe analysis (detection limit normally -200 ppm but -10 ppm by using special techniques), ion microprobe analysis (secondary ion mass spectrometry - SIMS; detection limit -0.2 ppm) or proton microprobe analysis (PIXE; detection limit

Jan 1, 1992

Structural assemblages of veins, shear zones, and wallrock alteration zones arising from fault-valve action on steep reverse fault systems are reviewed using observations from mesothermal gold-quartz lodes in the Archean Yellowknife, Abitibi, and Yilgarn greenstone belts of Canada and Western Australia, the Cretaceous Mother Lode system in the Foothills Metamorphic Belt of the western Sierra Nevada, California and the Victorian goldfield hosted in a folded quartz-turbidite succession of Paleozoic age in Australia. Despite differences in the host rock assemblages, the deposits have many structural characteristics in common. These form a useful exploration guide when re-evaluating comparable, but poorly described gold-quartz vein systems such as those in the Reefton area of New Zealand.

Jan 1, 1992

Recovery of tin and copper from concen trates containing cassiterite, stannite and chalcopyrite was studied in laboratory-scale tests designed to simulate continuous operation of the matte fuming process in which tin is recovered as SnS fume while copper accumulates in the matte. Charges made up of 300g of mixtures of the concentrate and siliceous flux were added at a uniform rate in pelletized form to crucibles containing 300g of matte and 50g of slag (both of which were recovered from previous tests), while blowing through the matte with air or oxygen-nitrogen mixtures at a rate of 3 to 5 1/min. Accurate material balances enabled the effects of process operating conditions on tin recovery and sulfur utilization to be deter- mined. When operated correctly, the matte fuming process gave tin recoveries exceeding 90 percent in spite of wide variations in the copper content of the matte and in the operat- ing conditions. Deterioration of tin recovery was associated with undersaturation of the slag with respect to silica, and with high partial pressure of sulfur dioxide (greater than approx- imately 0.2) brought about by oxygen enrichment of the blowing air. The utilization of sulfur varied widely in low grade mattes. Copper in excess of approx- imately 10% promoted formation of SO2 by the commonly accepted reaction: FeS + 1-120 2= FeO + S02 while in copper-free and lower grade mattes a substantial fraction of the oxygen was consumed in the alternative reaction FeS + i 02 = FeO + z S2.

Jan 1, 1980