Search Documents

Thank you for this opportunity to address your conference on The role of coal in the New Zealand energy market".New Zealand's energy market has, in common with much of New Zealand, undergone major change following the market reforms of the Labour Government.As far as the energy sector is concerned this change has been for the better, as it has created for the first time in a very long time a "true economic market" for energy in New Zealand.

Jan 1, 1990

Controlled Source Audio Magnetotelluric (CSAMT) surveys were carried out by Glass Earth (New Zealand) Limited (Glass Earth) in 2006 - 2007 to investigate epithermal gold targets in the central North Island of New Zealand. The surveys were conducted using a Zonge GDP 32 8-channels receiver and a Zonge XMT 32 transmitter powered by a 16 KW generator. The electric field dipole was maintained at 20 m length (five dipoles per 100 m spread) and the frequency ranged from 4 KHz to 4 Hz. Only scalar (TM mode) signals were recorded, using one magnetic coil per spread. The transmitter bipoles were 1 - 4 km in length and located about 5 to 10 km from each survey area.   Sixteen individual target areas were surveyed by June 2007. The CSAMT survey lines (100 - 400 m spacing) were determined mainly on results from previous ultra-detailed airborne magnetic and gravity surveys conducted by Glass Earth in 2005. The data from each CSAMT line was carefully examined to remove any spurious signals and processed using Zonge SCS2D software, which can produce smooth 2D resistivity inversions of the field data. The results were presented as resistivity sections and maps to help the identification of exploratory drilling targets, mainly from the existence of subsurface high resistivity zones (resistors) that can be interpreted as caused by silicification associated with epithermal mineralization.   An example of processing and interpretation of the CSAMT data is presented in this paper on results from Glass EarthÆs Tahunaatara target, where CSAMT surveys have identified zones of epithermal mineralization confirmed by exploratory drilling.

Jan 1, 2007

FOR some time past keen interest has been shown in both America and South Africa in the mining drill-steel problem. This interest has extended to Australian mining fields, and Australian drill users, ever desirous of increasing efficiency, are vigorously attacking the problem. The writer has recently been engaged in the investigation of the problem on two of ,the biggest mining fields in Australia, and has formed very definite conclusions concerning the causes of many drill-steel casualties. He puts these views forward in the hope that they may be of interest to, both drill manufacturers and drill users. The subject is here dealt with mainly from the aspect of the properties of the steel and the modifications of these properties whensubjected to various manipulations. It is generally admitted that the drilling machine has greatly increased in power and efficiency during recent years, and the consequence is that the machine is demanding better service from the steel. This is being impressed on the drill users by an increase in steel casualties. This fact has led many mining people to the view that the machine has developed so rapidly that the steel maker has not been able to keep pace, and that consequently the steel isfailing by fatigue 0:1; so-called crystallization. This view is rather depressing. The writer, on the other hand, is inclined to discountenance fatigue as a serious factor under good normal working conditions where the steel is carefully manufactured and supplied to the user under suitable structural and sound conditions, and has subsequently received kind treatment at the hands of the drill sharpener and the drill user.It is not reasonable to attribute failures to fatigue until it has definitely been proved that the steel is fundamentally sound and is in the best structural condition to resist the stresses it is called upon to withstand, and, this being so, that all fundamental principles of...

Jan 1, 1923

By Wasp E. J

A review is given of recent commercial long distance slurry pipeline systems in- stalled worldwide. The technological advan- ces in slurry engineering and system opera- tion are discussed, together with a brief re- view of the economics of slurry transportation and future trends in the industry.

Jan 1, 1973

Traditionally trucks have dominated haulage in open pit mines. Only recently have conveyors begun to be used in the long haul and high lift duties of surface mines. Steep angle conveyors are proven versatile systems for elevating or lowering materials continuously at steep angles to 90¦. This paper describes the design of a bucket-type steep angle conveyor that was developed as a joint research project between the Western Australian School of Mines and the Maanshan Institute of Mining Research in China. The steep angle conveyor can be used as a viable option for transporting blocky ore from open pit mines. A pilot conveyor was constructed and tested to determine its technical and operational feasibility. Furthermore, a computer model based on Matlab mathematical modelling software was developed to simulate the performance of the pilot conveyor. The model enabled to determine the design parameters of industry-scale conveyors to yield satisfactory performance. These conveyors become very cost-effective for those mines having large mine lives and depths greater than about 500 metres.

Jan 1, 2003

By Seymour K. M, Sampson D. B, Walker I. W

Ashton Mining Limited is the operator of two wholly-owned gold mine/mill complexes at Laverton and Leonora. In addition, Ashton owns 43% of the Bardoc Joint Venture mine/mill complex, which is operated by Aberfoyle Pty Limited. All three of these operations are located in the Eastern Goldfields region of Western Australia (Figure 1). At Laverton, milling capacity is in the order of 1 million tonnes per year in 3 mills (Duketon 200,000 tpa, Cork Tree Well 650,000 tpa and Craiggiemore 150,000 tpa). These mills service a distance of 80 km, from Baneygo in the north to Craiggiemore in the south. Mineral tenements cover a 150 km long stretch of a series of sub-parallel mineralised structures. At Leonora, the Harbour Lights mill is designed to treat 750,000 tpa of sulphide ore, and has treated oxide ores at an annualised rate of over 1 million tonnes/year. The mill is supported by several tenement blocks that lie within a 50 km trucking radius of the mill. The most important of these is the Mertondale tenement block, which covers approximately 25km of the Mertondale Shear Zone.

Jan 1, 1991

The basic flowsheet for the Kalgoorlie Nickel Smelter and Kwinana Nickel Refinery are discussed in relation to the mineral components of Kambalda produced nickel concentrates. Both processes handle violarite and pentlandite satisfactorily but the smelter has limitations where high copper recovery is required and in its ability to handle magnesia containing minerals. While the latter can be more economically handled at Kwinana the limitations of this tolerance are discussed together with problems arising from treating pyrrhotite, pyrite and precious metals by the Sherritt Gordon process.

Jan 1, 1973

Problems associated with gas management become more significant as exploitation of coal reserves in the Bowen Basin in Australia becomes deeper. At Oaky North mine, relocation of production from one area of the mine to another with a higher gas content required the use of pre-drainage, post drainage and inertisation techniques to enable production activities to continue largely uninterrupted. Innovative surface to inseam drilling techniques were developed for pre-drainage of reserves close to mine workings and have proven to be largely successful. The gas management techniques adopted and specific experience gained are discussed in this paper.

Jan 1, 2005

By Schiller J. C, Both R. A

Base metal mineralisation occurs at several locations within the regionally metamorphosed Kanmantoo Group on the southeastern flank of the Mount Lofty Ranges between Kanmantoo and Strathalbyn, 50 km southeast of Adelaide. Sulphide mineralisation is of three main types (Seccombe et al, 1985):1. copper deposits, at the Kanmantoo and Bremer mines, South Hill prospect and several minor occurrences,2. lead-zinc deposits at Aclare, Wheal Ellen, Strathalbyn, St. Ives, Scott's Creek, and Glenalbyn mines,3. pyrite-pyrrhotite mineralisation of the Nairne pyrite deposit and many other pyritic schist units within the Kanmantoo Group.Syntheses of folding, metamorphism and stratigraphy of the Kanmantoo Group were given by Kleeman and Skinner (1958), Offler (1960, 1963), Offler and Fleming (1968), Marlow (1975), Mancktelow (1979) and Parker (1986). Studies of the general relationships of mineralisation to structure in the Kanmantoo area were given by Grasso and McManus (1954), Mirams (1962), Poole (1969), and Lindqvist (1969).Several conflicting views on the origin of mineralisation in the Kanmantoo Group have been proposed. Thomson (1975) considered much of the mineralisation as a late-stage product of regional metamorphism and he, like Parker (1986) and Lambert et al (1987), stressed the importance of major lineaments as an ore control. However, Lindqvist (1969) and Verwoerd and Cleghorn (1975) tentatively suggested a syn-sedimentary origin to the Kanmantoo copper deposit and Jensen and Whittle (1969) and Seccombe et al. (1985) on the basis of sulphur isotope data proposed a bacteriogenic sulphur source and a sedimentary origin for sulphides in the Nairne pyrite deposit. The latter suggested that most copper deposits represent stockwork, vein or disseminated zones within subsurface vents whereas massive mineralisation at Wheal Ellen and Aclare mines probably accumulated on the ocean floor.This paper presents new geological information on the structural and metamorphic setting of the base metal deposits and attemptsto relate this information to previous regional studies of the Kanmantoo Group. Estimates of pressure and temperatureof peak metamorphic conditions based on silicate mineral stabilities are considered in relation to various silicate and sulphidegeothermometers which have not previously been applied to rocks in the Kanmantoo Group.

Jan 1, 1988

Although forty-seven years have passed since the by-product coke oven made its successful commercial appearance, it is only during the past fifteen or twenty years that this system of coal carbonisation has advanced rapidly to its present position ofabsolute supremacy.Early designs of by-product ovens proved more or less faulty, and the coke produced was so inferior to coke made in beehive ovens that there was a natural hesitancy on the part of coke producers to invest large sums of money in installations of by-productovens of doubtful utility-more especially in view of the fact that beehive ovens could be erected cheaply and operated by non technical labour for the production of high-grade coke under the most variable conditions of trade.Surely and steadily designers brought forward by-product ovens of improved type, coupled with more efficient apparatus for the recovery of by-products, but still the industry lagged, due almost entirely to the insistence on the part of coke users that the qualityof ordinary beehive coke was vastly superior for metallurgical operations to the best coke produced from by-product ovens. So deep rooted was this prejudice that only the passage of time could eradicate it. That it has successfully done so is strikingly illustratedin the following statistics:

Jan 1, 1928

The continued exploration of the major brown coal deposits of the Latrobe Valley has resulted not only in the discovery of huge additional reserves, but also in new concepts of the stratigraphy and structure of the coal seams in that area. The author sets out his interpretation of the new information which has become available over the last six years.A section of the paper is devoted to the quality of the coal. As the chemical composition of these brown coals has been discussed in some detail by previous authors, only the major constituents and the heat value of the coal are dealt with in this paper. Some of the variations in quality are related to the geological structure.The occurrence of underground water and its relation to open cuts is dealt with briefly.INTRODUCTIONThe Latrobe Valley Tertiary Basin is almost entirely covered by a layer of Post Tertiary sediments which mask the underlying rocks and their structures. As a result, the geological understanding of this area has had to await the comprehensive drilling campaign in search of brown coal, initiated by the Victorian Mines Department in 1917, and subsequently carried on by the State Electricity Commission of Victoria. The first detailed geology was published by Herman (1922), and this was followed some 25 years later by papers by Edwards, and later Thomas and Baragwanath, to which reference will be made later in this paper. Herman included a section on the geology of the Latrobe Valley in his book Brown Coal, which was published in 1952.Since that time a considerable amount of new information has become available from the continued drilling carried out by the Commission. In addition, geophysical work carried out by the Commonwealth Bureau of Mineral Resources has assisted in the defining of geological structures in the area.

Jan 1, 1960

By Kubo H, Kubita K, Morinara M

A quantitative method for predicting the mechanical properties of zinc alloys is proposed on the basis of the molecular orbital calculation of electronic structures. A new parameter which is the s-orbital energy level, Mk , of alloying elements in zinc was introduced into this method. This Mk parameter correlates with the electronegativity and the atomic radius of elements. The compositional average of this parameter varied linearly with the tensile strength and the hardness of commercial alloys and some alloys developed by Mitsui. This electronic method was very convenient in designing high performance zinc alloys efficiently.

Jan 1, 1993

By Patridge A. C

A pilot scale laboratory investigation of manual slurry sampling methods representative of those used in the minerals industry is described. Samples were taken from slurries made up from silica particles of various sizes and in various concentrations from a stirred tank and from the discharge lip of a rectangular launder. Sampling methods from the tank included immersion flasks and several configurations of a suction probe. The launder was sampled using a conventional narrow-mouth ladle and also with a 'mouth organ' stream splitter. Samples were analysed for overall solids concentration and size distribution and showed different but always significant and often large biases relative to the known overall composition of the slurry, the nature and extent of bias being dependent on pulp concentration, particle size, sampling method and sampling location. Results clearly show the very great difficulty of obtaining representative samples by simple sampling techniques, although the data suggest that errors can be reduced by using an appropriately designed and operated suction probe. Further work will be carried out with the objective of establishing guidelines for industrial sampling practice.

Jan 1, 1995

By Carter J. P

A two year study into the effects of coal mining induced subsidence on cliff lines was undertaken by the Department of Mineral Resources with the support of a grant under the National Energy Research, Development and Demonstration Program. A new monitoring technique, using an Electronic Distance Meter and acrylic reflectors attached to the cliffs, provided safety for the surveyors and extensive and accurate three dimensional displacement data on the movement of the cliffs as they were being undermined. The study report included many graphs showing the measured vertical and horizontal displacements, differential subsidence, tilts and strains and included analysis of these movements with various parameters, such as, seam thickness, depth of cover and distances between the reflectors, longwall face and the edge of the chain pillar. Some of these graphs are presented in this paper and could be used, with caution, to predict subsidence movements around other cliff lines, after allowing for differences in geology and mining layout. A mechanism is suggested as an explanation for the observed high horizontal movements around the cliff lines. Sixteen percent of the overall lengths of cliffs that were undermined during the monitoring study fell and the contributions of various factors that appeared to influence the cliff falls are discussed. It is concluded that no single factor dominated as the major cause of the cliff falls and, often, many factors combined to cause cliff face instability.

Jan 1, 1992

By Wilson R. G

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port KKembla steelworks of Australian Iron and Steel Pty. Ltd., vary in rank and in type over the Southern and -South Western Coalfields. The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal. Plans of seam variation show the regional trends in rank and type for each sear. The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Sean in a zone embracing Bulli and Appin Colleries.

Jan 1, 1969

By Finlayson E, Hilyard D

1:100 000 geological mapping of Bougainville Island has resulted in refinement of stratigraphic subdivisions and relationships. We subdivide the sequence into basement Atamo Volcanics (Late Eocene-Early Oligocene), consisting of spilitised pillow basalts, which are overlain unconformably by Late Oligocene-Early Miocene Keriaka Limestone. The latter is unconformably overlain by fine-medium grained volcaniclastics and minor lavas of the Middle-Late Miocene Toniva Formation which coarsens upward and passes gradationally and conformably into the coarsely volcanolithic latest Miocene-Pliocene Arawa Conglomerate. The Kupei Complex, host to the Panguna.porphyry Cu-Au deposit, consists of medium - K20 microdiorites, granodiorites, and andesites intruding Arawa Conglomerate and Toniva Formation. K/Ar isotopic dates on the Kupei Complex range from 4.8-1.3 Ma, and hence overlap the age of the Arawa Conglomerate. We believe that the Arawa Conglomerate consists of mass flow deposits on a volcani- clastic apron surrounding a volcanic edifice above the intruding Kupei Complex.

Jan 1, 1990

By Parsons A. E

The application of known pelletizing tech- nology was successful in the agglomeration of zinc concentrate into pellets of minus 6mm siz- ing using fine zinc calcine and sulphuric acid as binder. Subsequent roasting trials conducted in a 0.3 m diameter fluid bed reactor, showed that the pellets satisfactorily withstood hot physical abrasion during fluidization. Fines generation was low and the pellet calcine was hard, possessing excellent handling properties. Results of laboratory scale static pellet sinter- ing tests showed conclusively that the deterior- ation in sinter physical quality experienced with fine calcine was not apparent when the calcine was added to the mix in pellet form. Based on the results of small scale exper- imental work, a one tonne per hour pilot plant was constructed and operated. Several thousand tonne of pellets were produced-for fluid bed roasting in Badische Analin and Soda Fabrik (B.A.S.F.) turbulent layer (T.L.) roasters previously designed for roasting iron pyrite concentrate. Continuity of the T.L. fluid bed roasting operations was achieved when the waste heat boilers were replaced with atmospheric coolers and thus eliminated the problems of gas flow restrictions. Sinter plant trials were conducted over a period of two weeks with the addition of pellet calcine to the sinter feed. Results showed a marked improvement in sinter plant performance, and as a result of better bed permeability, increased sinter production was achieved, with- out significant deterioration in sinter quality.

Jan 1, 1974

Gold is actively precipitating at grades up to 80 g/tonne at and near the surface of the Waiotapu geothermal system, located in the Taupo Volcanic Zone of New Zealand. Many characteristics of this active system makes it analogous to the environment deduced for epithermal precious metal mineralisation in the circum Pacific region.The near surface area of the geothermal system is approximately 17 km2, caused to an extent by the upflow of deep, neutral pH fluids being deflected into a lateral flow of several km. This fluid has pervasively altered the rhyolite pyroclastic and ash deposits to an assemblage generally characterised by the term propylitic; major vein mineralisation is not observed. The temperatures at the 1100 m limit of drilling are 300¦C, and decrease to the surface along a boiling point curve.Condensation of steam and H S (subsequently oxidised) at the surface (derived 2from deep boiling) results in the formation of heated acid sulphate waters. These have caused a shallow (50 m) cap of advanced argillic alteration. Mixing of this oxidised condensate with the deep neutral pH fluid appears to be the principle cause of gold deposition from thiosulphide complexes. The major focus of gold mineralisation is in Champagne Pool, a hot spring which fills one of several 900 year old hydrothermal eruption craters.

Jan 1, 1984

Before presentIng my address I wish to acknowledge the honour which has been conferred on me by my appointment to the position of President of the Australasian Institute of Mining and Metallurgy.It is a matter of great concern to us all to find our Empire at war. I am confident that, as was the case in the war of 1914-1918, members of this Institute and of kindred Institutes and Associations will contribute in full to the Empire's needs and that in the end our cause shall triumph.I think it appropriate that I should take as the subject of my address that of the Broken Hill Lead-Silver-Zinc Industry. The subject matter of this address has been confined to the operations of Mining, Ore Dressing, Lead Smelting and Refining and production of Electrolytic Zinc in Australasia. The review of the Broken Hill Lead-SilverZinc Industry would not, of course, be complete without reference to those Australian industries which trace their origin to the Broken Hill field, but· it is thought that an outline of these industries would make thIs review too extensive.HISTORICALMany efforts have been made to translate the early history of Broken Hill and its subsequent growth throughout the years into one of the wor~d's most famous mining fields in the form of a simple story.

Jan 1, 1940

Production implications of the introduct- ion of electric L.H.D. units in sublevel open stoping and pillar recovery at Rosebery are covered by Faulkner (1982) and Carlton (1982). The following engineering aspects associated with the decision to introduce electric L.H.D.'s are considered here: - Initial requirements for commissioning, including power reticulation at an adequate level to all operating areas. - Conversion of a manual system to radio remote control. - Maintenance backup requirement to ensure that the production potential is realised.

Jan 1, 1982