Search Documents

By D David

The development of Western Australian magnetite deposits has lead to the design of some of the largest grinding mills and plants in the world. One of the projects demonstrates the efficiency gains possible by developing a simple yet thorough test program for circuit design. By drawing on the experience of current magnetite operations in Australia and the Mesabi and Marquette iron ranges in the United States, a basic flowsheet was developed. Through comprehensive testwork with AG, ball and stirred milling the flowsheet was optimized to take full advantage of each grinding mill’s strengths to reach the required final grind size. Laboratory work was verified in the pilot plant to optimize the energy efficiency of each grinding step while ensuring adequate liberation at each step for sufficient gangue rejection. By using three stages of grinding, the ball mill can best be employed in ensuring all top size gangue material is liberated and removed in the second magnetic separation step. The inclusion of the IsaMill, with its inherent steep product size distribution, as the tertiary grinding stage ensured that maximum grade was achieved and simplified the downstream process while giving further improvements in total grinding capital and operating costs. In this way the combination of the two technologies downstream from the AG mill is far more efficient than either would be on its own by reducing the total installed power by 1/3 and annual grinding media cost by 2/3.

Aug 8, 2011

By G Chitumbura

Raise boring is a critical aspect of mining at Xstrata Copper’s Mount Isa Copper Operations (MICO). MICO’s internal raise boring department regularly develops ventilation rises, orepasses and stope cut-off rises and reams approximately 2500 m per annum. Developed, trialled and implemented as standard practice over the past two years, procedural changes in constructing the raise bore machine’s foundations have significantly reduced operator exposure to raise boring’s inherent risks of working around open holes and manual handling. An additional cost benefit of this newly-adopted procedure is derived from reducing the likelihood of damaging the machine while de-rigging.When conforming to standard industry raise boring practices, exposure to an open hole begins when the reamer breaks through the concrete pad and ends when it is removed from the hole – a process which, depending on the size of the hole and the raise boring machine, can take up to three days to complete. Although wearing fall restraint equipment, operators working on and around the raise bore machine during de-rigging are continually exposed to the risk of falling from heights. In contrast, MICO’s newly-developed and successfully-implemented presink raise boring system reduces this exposure to a maximum of four hours, regardless of hole size. Exposure to manual handling hazards is also substantially reduced as the presink procedure eliminates manual placement of a 100 kg drill bit under the machine to commence pilot-hole drilling. Outcomes of implementing the presink System at MICO have been so beneficial that it is now standard procedure for all reaming in excess of 1 m diameters.

Mar 21, 2011

By M A. Llano-Serna, D J. Williams, L Bu

Tailings dam failures continue to occur worldwide at an unacceptable rate, averaging two events annually over the last 100 years. Furthermore, tailings dams continue to grow in size, increasing the potential release of tailings and water should they fail. Tailings are generally deposited in a slurry state, with the potential to flow if containment is lost. Understanding the generation and propagation of excess pore water pressure on failure is critical to predicting the flow and run-out of tailings. This paper presents numerical modelling using the material point method indicating that tailings run-out processes may be self-enhanced by the excess pore water pressure induced during the collapse of the containment. Moreover, it is shown that geomorphological features, such as the slope and its surface roughness downstream of the tailings dam, influence the pore water pressure dynamics upstream of the advancing toe.CITATION:Llano-Serna, M A, Bu, L and Williams, D J, 2018. Excess pore water pressure induced during tailings run-out, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 377–383 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By C E. Woolley, A Hosseini, J Foster

Northern Star’s Thunderbox Open Pit C-Zone cutback was designed to maximise extraction in a short life excavation; In fresh rock on the western wall this included 20 m to 30 m bench heights with 6.5 m to 10 m berm widths and a 90° pre-split angle. Rock mass quality in this area is generally fair to good, however, there are sections where the dominant foliation runs parallel with the designed pit wall, and more closely spaced, altered, foliation is present: these areas are difficult to predict and prone to failure. Stringent controls and monitoring were required in order to safely access below these areas, in particular the use of slope stability monitoring radar, Trigger Action Response Plans (TARPs), re-entry procedures, visual inspections, drone inspections and day-to-day personnel awareness of the hazard. Robust and comprehensively planned remediation was also required after two significant slope failure events where long reach equipment and rope access techniques were utilised to remediate the areas in question safely, but also in a timely manner, such that expected production targets were impacted as little as reasonably practicable. This combination of rigorous risk management and well planned remediation resulted in a successful and complete extraction of the C-Zone cutback with no impact to operational safety.

Jun 22, 2022

By T J. Laing, A B. Richards, A J. Moore

Blastholes fired in a pattern with a constant initiation delay create a frequency in the ground vibration similar to that from a percussion instrument, such as a drum, in the air. A constant firing delay generates a prime or forcing frequency into the ground motion. The forcing frequency may then be modified by ground transmission characteristics into subharmonics of the forcing frequency. The moving vibration source between blastholes also creates a frequency shift because of a Doppler effect. Other wave interactions may form beats. The effects are exacerbated by the accurate firing times of electronic detonators. This paper demonstrates how observations of wavetraces and frequency spectral analysis were used to recognise:Doppler effect and frequency ellipsoidssubharmonics (and sub-subharmonics) of the forcing frequencybeat formation that may double or triple peak particle velocity (PPV) levels.Recognition of beats permitted techniques to be used to control ground vibration from coal overburden blasting to limits deemed to cause no further instability in a slip failure. An understanding of the science involved has practical application elsewhere that has been successfully applied to initiation timings to reduce PPV and adverse human and structure response from other blasting operations.CITATION:Moore, A J, Richards, A B and Laing, T J, 2015. Blasting harmonics and controlling peak particle velocity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 527–532 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P Chapman, B Moosapoor

The objective of this paper is to present the potential applications of geostatistical analyses in planning CPTu investigations, as well as interpolation of CPTu data. The paper presents a case study of a geostatistical analysis of CPTu data undertaken between 2004 and 2017 for an upstreamraised TSF located in the Goldfields region of Western Australia. An initial model is developed using the 2004, 2009 and 2017 CPTu data. The model is used to predict in situ cone tip resistance (qc) measurements, as the interested primary variable, at the selected locations where 2019 CPTu were undertaken, and the results of the prediction and the actual data are compared.

Jul 1, 2021

By H Lehtonen, H Mansikkaviita

In primary copper smelters, the received copper concentrate and other materials contain a certain amount of moisture, ranging from six to 14 per cent. Moisture in wet concentrate has a negative effect on the performance of the smelting furnaces when it is fed directly to the furnaces, namely increasing the energy consumption and the off-gas flow. There are several drying technologies available for drying copper concentrate, varying from direct heated rotary dryers and flash dryers to indirect heated steam dryers. Application of steam dryers has changed the drying process for copper smelters. Produced from a waste heat boiler, steam as heating medium enables plant-wide heat utilisation. Fossil fuel used from outside sources to remove water is no longer required and the combustion chamber is not required. In addition special attention has been paid to overcome the known problems of pollution emissions, excessive wear, clogging and frequent maintenance. The Kumera steam dryer is featured with many advantages based on principal improvements in reducing tube element wear and increasing drying efficiency. Thus, it has been considered as the first choice for those smelters where steam is available.

Jan 1, 2006

By B D. Saffron

In 1983, open cut coal mining operations were suspended at the Tent Mountain coalmine, located in Alberta, Canada in an area called Crowsnest Pass. Montem Resources (‘Montem’), an Australian mining company, purchased the asset in 2016. They conducted several drilling campaigns and undertook environmental monitoring with the intent to restart operations. In 2020, Montem completed a Definitive Feasibility Study, which indicated a mine life of more than 14 years.

Aug 2, 2023

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By G Balog, T Ormerod, D Sidea

Carrapateena is a copper-gold sub level caving operation located in the Gawler Craton, South Australia. One of Australia’s largest undeveloped copper deposits, the project will be a 4.25 Mtpa underground operation, with an estimated mine life of 20 years (OZ Minerals, 2017). First concentrate production was achieved in December 2019, within the Iron Ore Copper Gold (IOCG) hematite breccia complex. The Carrapateena orebody is overlain by 500 m of barren sediments of the Stuart Shelf, which hosts two aquifers. The cover sequence is dominated by shales, quartzites and sandstones in order of thickness. The cover sequence presented challenges to the mine ventilation system as a result of highly variable rock strengths. On this basis, the site developed the first vent rise, Vent Rise 5 (VR5), earlier than required as a means to test the empirical stability assessment. Assessment for VR5 was completed in 2017, with the mine yet to develop through much of the cover sequence. Due to the geotechnical data available at the time, it was anticipated that break out would occur within the vent rise walls as a function of the low strength Woomera shales. VR5 was developed to 4.5 mᴓ in late 2018. The timing of the VR5 development enabled the site technical team to calibrate empirical stability factors for the assessment of future vent rises. At the time of writing, four additional vent rises have been successfully developed to a diameter of 5.5 m. No significant overbreak has been observed within any of the vent rises. This paper is intended for geotechnical practitioners designing large-diameter vent rises in geological environments similar to the Stuart Shelf where a similar approach to vent rise design may be warranted.

Mar 15, 2021

By R Marchant, D Willingham

"Predictive maintenance (also known as PHM or equipment ‘health monitoring’) refers to the intelligent monitoring of equipment to avoid future equipment failures. In contrast to conventional preventive maintenance, the maintenance schedule is not determined by a prescribed timeline; instead, it is determined by analytic algorithms, such as machine learning, using data collected from equipment sensors and/or via simulation.Predictive maintenance offers the following benefits for operators and equipment manufacturers:reduction of equipment downtime by identifying issues before failure, thereby enabling convenient scheduling of equipment service and extending equipment lifetimeautomatic determination of the root cause of the failure, enabling appropriate service to be performed without utilising resources to determine a diagnosis avoidance of costs of unnecessary maintenance and unexpected failures improved safety and product quality.Algorithms and data are critical to predictive maintenance success. Sensor data preprocessing is performed using advanced statistical and signal processing techniques. In the case that data isn’t available for the full range of operating modes, operating scenarios can be simulated. Machine learning techniques are then used to estimate equipment health. Once tested, predictive maintenance algorithms may be operationalised in an IT environment such as a server or cloud. Alternatively, algorithms may be implemented in an embedded system directly on the equipment, allowing for faster response times and significantly reducing the amount of data sent over the network.In this paper, we use both historical and simulated data of the plant under various modes of operation including run to failure, and we then leverage machine learning techniques in MATLAB to estimate degradation and remaining useful life. This technique, of combining both simulation models and machine learning, in the areas of predictive maintenance and equipment health monitoring has been adopted by Safran, makers of aircraft jet engines, since 2007. They now have over 160 modules developed (Lacaille and Aurelie, 2015).Citation:Willingham, D and Marchant, R, 2016. Predictive Maintenance Using Simulation and Machine Learning, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 279–284 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By D Gerrard, J Begelhole, J Gerber

The Iron Magnet deposit has been mined since 2007 when Arrium (then OneSteel) commissioned the magnetite concentrator to supply feed to the pelletising plant in Whyalla. The concentrate quality requirement for the customer required consistent product with minimal variability. In the early stages of operation, it was identified that the feed variability introduced significant changes in the concentrate quality, which was outside the acceptable customer limits.In 2011, a geometallurgical regression model was developed that allowed for the estimation of concentrate quality produced from the feed material. This was based on a laboratory-scale Davis Tube Recovery (DTR) test performed on the feed material. The objective of the project was to characterise the raw ore in the pit to allow for blending prior to crushing. By blending the feed to the concentrator, minimal concentrate quality variation within the plant was achieved. The orebody was divided into geometallurgical classes, called ore types, based on the mineral texture and magnetic mass recovery. Each geometallurgical class consisted of material with similar metallurgical performances. For each individual blast pattern, the ore was grouped into the geometallurgical classes and a composite sample was created. The composite sample was put through the laboratory-scale DTR test and the results were used to estimate the metallurgical performance of the material.The characterisation process and feed pile build methodology was applied in early 2013 and went through an optimisation and streamlining phase. Since the implementation of the geometallurgical characterisation process, the plant has seen a significant reduction in concentrate variability and measurable throughput gains. The characterisation process has also increased the amount of material that is now classified as ore.CITATION:Gerber, J, Gerrard, D and Begelhole, J, 2015. Geometallurgy of the South Middleback Ranges magnetite deposit – predicting plant performance from the pit, in Proceedings Iron Ore 2015, pp 555–560 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

TSL Concepts and Practical Examples of the Non-Reactive System - Meyco TSL 865 Thin Spray-on Liners (TSLs) have been intensively investigated by mining and chemical industries within the last decade. Apart from the basic concept of spraying thin liners, expectations of the product's performance vary, eg immediate active strata support is seen as a key to control the ground permanently. For many coal mines this is an important factor to reduce maintenance in their roadways and enable permanent production from the long wall. In opposition to a passive mesh system this technology offers immediate active support to the strata. But not only coal mines are interested in TSL technology, there are potential applications in hard rock mines, during shaft sinking, pillar support and as an anti-weathering sealant. This paper will explain the advantages and disadvantages of TSL concepts; it will give examples of successfully applied TSLs with a main focus on the non-reactive and flexible system MEYCO TSL 865 by BASF. Furthermore, it will indicate the limitations and discuss briefly the bearing capacity and reasonable lab testing of such systems.

Nov 25, 2010

By K White, C Ferguson, M Harding

Understanding watercourses and river processes at a landscape scale is vital for managing risk to mining infrastructure and operations as well as minimising future environmental impacts beyond the life of the mine. Recognising this, Iluka Resources Limited engaged Alluvium Consulting Australia to identify and characterise watercourses across several neighbouring mineral tenements in the Eucla Basin, South Australia (Alluvium, 2013, 2014a, 2014b). The objective of the studies was to inform planning for risk management during mine planning and operation and appropriate landscape rehabilitation for mine closure.Mining operations in the area are by open cut extraction of mineral sands. The extracted resource is processed on-site before leaving the site for export. Several pits are to be developed in stages with simultaneous backfilling and surface reinstatement. Mining is initially taking place in the Jacinth tenement, where up to 100 km of watercourses may be directly or indirectly impacted (refer to Figure 1).The total study area (shown in Figure 1) is approximately 330 km2 and spans three smaller areas that were the focus of separate investigations during mine planning.CITATION:Ferguson, C, White, K, Harding, M and Hardie, R, 2016. Landscape-scale assessment of watercourses in remote arid South Australia to inform mine planning to mine closure, in Proceedings Life-of-Mine 2016 Conference, pp 200–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By A Moreira, A B. De Souza, S Latchireddi, E Faria

Material transport plays a significant role in the efficiency of horizontal grinding mills - autogenous (AG)/semi-autogenous (SAG)/ball mills. The magnitude of benefits that can be achieved with efficient material transport in AG/SAG mills has been demonstrated in a greenfield milling operation at Mirabela MineratpoÆs SantaRita Nickel operation located in north eastern Bahia in Brazil. This grinding circuit was commissioned in October 2009, was designed as a typical SABC circuit to grind 4.6 Mt/a (575 t/h) to produce a P80 of 125 ¦m with ten to 12 per cent ball charge in the SAG mill. However, it has been operating as an ABC circuit without any grinding media in SAG mill. The nameplate design capacity was achieved in few days and was gradually increased to an average of +800 t/h, still operating in ABC mode. The Santa Rita grinding circuit consists of one 30 ft + 15.4 ft 8.5 MW SAG mill fitted with Outotec patented Turbo Pulp Lifters (TPLÖ) in closed circuit with a HP400 short head pebble crusher and one 20 ft + 28.4 ft 5.5 MW Ball Mill in closed circuit with a Warman cyclone cluster fitted with 10 + 26 in CAVEX cyclones. This paper examines the comminution design process, operating philosophies, experiences, post commissioning optimisation and future development works. Evaluation of the milling circuit performance relative to the design criteria is also discussed.CITATION:De Souza, A B, Latchireddi, S, Moreira, A and Faria, E, 2012. Application of turbo pulp lifter in greenfield operation - Mirabela SantaRita nickel operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 53-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S Pradhan, A Kuras, R Mahajan

This paper describes the design of the precast concrete segmental lining for the 13.1 m internal diameter and 450 mm thick, 2.4 km long mainline tunnels for the Waterview Connection project in Auckland for the New Zealand Transport Agency.The design and detailing of this segmental lining presented some noteworthy challenges, including an alignment that has sections of low cover in soft ground. Key points of interest are that this precast segmental lining is the largest to ever include steel fibres as the primary method of reinforcement and the lining includes cams on circumferential joints to control ring deformation.The paper describes some of the key design decisions that were made in a collaborative manner with the construction team, tunnel boring machine manufacturer, segment manufacturer and the designers.CITATION:Mahajan, R, Kuras, A and Pradhan, S, 2014. Design of segmental lining for Waterview Project, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 289–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By K Gardner, R Fraval, V Singh

Using new technology to create optimised infill drill programs in underground or open pit settings, it is possible to quantify the value of a drill program. The computer designed programs are optimised to uplift the most amount of resource possible into the specified resource classification, while honouring geological, spatial, equipment and budgetary constraints. When designing ‘by hand’ balancing all these factors is a time-consuming effort with no real way to determine metrics on ‘how good’ a program will be. The optimisation considers many factors allowing geologists to apply critical thinking and domain knowledge to constrain the optimisation, letting the computer do the heavy lifting of determining hole placement. Once programs have been created, they can be integrated into a production schedule. This is a critical step in determining the correct sequencing and balancing of resource availability and seeing how a program will interoperate with other tasks in the mine. For example, if drill drives are a requirement for part of the program, will they be developed in a time frame that is useful for the goals of the program? Do we risk drilling infill holes too late to add value? Do we put production at risk by not classifying parts of the model ahead of time, thus adding to uncertainty? Using software to assist with optimising and scheduling of drilling is a useful technique to save the geologists from the mundanity of manually designing drill programs and puts metrics around the effectiveness of a program and has the potential to add quantifiable value to a program. Examples will be presented that demonstrate the effective use of drill hole optimisation, comparing manual designs with optimised designs, as well as the examples that show the effective use of scheduling.

Mar 22, 2022

By G Balog, T Ormerod, D Cox

This paper discusses the methods utilised by the technical team to identify and quantify the SLC risk factors, the modifications to mine design and scheduling, and the changes to the planned risk management practices. The paper also describes the future work currently planned by the OZ Minerals technical team to quantify the various risk factors in terms of space, time and magnitude. This may better inform the future mining practices within not only the Carrapateena province but also the wider Gawler Craton.

Mar 15, 2021

By J Sargeant, T Levi, J Theiler, B Beamish

Two coal samples (810 Panel and Area 900) collected from Clarence Colliery have been tested under a controlled heating procedure to evaluate the gas evolution trends corresponding to increasing temperature. Gas evolution data are normally used to identify key gas indicators and validate the trigger action response plan settings for the mine as part of the Principal Hazard Management Plan for Spontaneous Combustion. The samples were located some 6 km apart and there is a significant coal-type difference between them. At low temperatures (<100°C), the Graham’s ratio (GR) values for the two samples are almost identical. However, at elevated temperatures, there is a significant difference, with the 810 Panel coal having higher GR values than the Area 900 coal. This is most likely due to a difference in the coal reactivity. The 810 Panel coal does not evolve ethylene until temperatures in excess of 140°C are reached, whereas Area 900 coal evolves ethylene once temperatures in excess of 120°C are reached. The 810 Panel coal also produces significant ethane evolution (200 ppm) at low temperatures (50°C) due to the presence of retained ethane seam gas, which decreases as the temperature increases due to desorption from the coal. Once the coal temperature exceeds 130°C, the ethane evolution increases again due to coal oxidation reactions, reaching levels of 50 ppm. In contrast, the Area 900 coal has no significant low-temperature ethane evolution, and ethane evolution only increases once the coal temperature exceeds 120°C. There are also noticeable differences in the trends of other gases evolved from the coal. These findings have implications for the interpretation of gas monitoring results from the two different areas of the mine. They also illustrate the need for obtaining results from each new area of a mine as it develops so that changing gas evolution trends can be identified in advance of mining.CITATION:Beamish, B, Sargeant, J, Levi, T and Theiler, J, 2015. Gas evolution trends for coal from two different areas at Clarence Colliery, in Proceedings The Australian Mine Ventilation Conference, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Zharinov SE

Geonechanical modelling of island arc sys- tems and their analogs is investigated. Slow seismotectonic movements along the inclined deep fault zone under the compressive horizontal stress conditions are proposed to be the princi- pal mechanism controlling the structures and processes in the active continental margins. A model of shearing surface crack in an elastic half-plane is used for simulation. The main ele- ment of the model is viscous interaction bet- ween the crack sides, the viscosity varying with depth. To describe the stress-strain state of the medium an integro-differential singular equation is derived and solved numerically. The results of simulation are in good agreement with geological and geophysical data on the ac- tive continental margins.

Jan 1, 1987