Search Documents

The Woodcutters deposit, 65 km south- southeast of Darwin, N.T., consists of a series of veins of pyrite, sphalerite, and galena with some silver, cadmium, antimony, and arsenic minerals. The veins are hosted by the Early Proterozoic Whites Formation, a sequence of black slates with interbedded carbonate rocks and minor ash tuffs. The known orebodies occur about 300 to 500 metres above the contact of Whites Formation with the underlying Coomalie Dolomite, which consists of dolomite and magne- site. The stratigraphic setting is lithologic- ally similar to that of the Mt. Isa deposit, Queensland. The orebodies are replacement veins occ- urring along fault and dyke structures which are sub-parallel to the axes of a double-nosed faulted anticline. The orebodies are in part associated with two unusual carbonatized lam- prophyric dykes. The dykes were intruded after the fold and its slaty cleavage were formed. The ore has replaced the dykes and host rocks and is therefore late-stage hydrothermal miner- alization. The known orebodies are open at depth. A "bonanza" of high-grade ore occurs at the upper part of the largest orebody and is currently the subject of an open cut mine planning study by a consortium of companies headed by Nicron Resources Ltd.

Jan 1, 1984

By Patridge A. C

Observations of coal stockpiles subject to unusual levels of instability showed that the particular coals exhibited 'gap grading', a relative lack of intermediate size particles. This led to a suggestion that fine coal particles within the pile might have been induced to migrate under the influence of water flow and to concentrate in relatively impervious layers, resulting in local water saturation and reduction of shear strength. To investigate this suggestion, a large test column has been constructed and washed coals with various levels of fines content have been subjected to a downward flow of water. Subsequent examination of the bed of coal within the column confirmed the percolation of fines and their concentration into horizontal layers, and showed the development of zones of saturation above those layers. Shear box tests showed differences in cohesion and internal friction angle between coals with different percentages of fines, supporting the hypothesis that fines percolation may lead to decreased stability.

Jan 1, 1995

By Membrey W. B, Partridge A. C

Lower transportation costs, improved handling and better utilization efficiency are some of the reasons that make low moisture coal product desirable. There has been considerable interest in the development of effective coal dewatering techniques to achieve this result. One avenue of considerable merit for enhancing dewatering processes is by modification of the surface chemistry of the coalwater slurry system by chemical means, resulting in better performance of existing equipment. This paper reports the results of an investigation of the utility of surface active agents in the enhancement of fine coal dewatering. A large variety of proprietary dewatering agents have been studied in relation to their efficiency in enhancing the dewatering of a number of Australian coals. Properties of particular coals that make them amenable to improved dewatering by particular chemical agents have been identified. Surface studies, including surface tension and zeta potential measurements as a function of surfactant concentration, as well as dewatering assessments, were used. Particular attention was paid to filtration, but the results could be applied to other dewatering systems.

Jan 1, 1989

By Gole MJ

The Goodyear nickel prospect is located 45 km southeast of Kalgoorlie (31.04¦S, 121.80¦E) near the eastern boundary of Hampton Area - East Location 45 (Figure 1). Nickel mineralisation was discovered on the Goodyear prospect in March 1996 when a reverse circulation drillhole (GYC5), initially drilled in December 1995, was deepened to meet a minimum footwall penetration requirement of 20 in that had been set for the drill program. Approximately 3 in of sulphides averaging 4.9 per cent nickel was intersected from 296 metres down-hole, this being within 2 in of the first end-of-hole. Hole GYC5 was part of an eight hole drilling program undertaken by Titan Resources in late-1995. This program was designed to test whether nickel mineralisation in the Dunlop prospect, discovered by the Western Mining Corporation - BHP Camylia Joint Venture immediately east of the East Location 45 boundary, continued across the tenement boundary. The area targeted by the initial drill program had been explored by Western Mining Corporation in the mid-1980s using extensive surface sampling and a drilling program that included 17 RAB and percussion drillholes. None of these holes intersected nickel Mineralisation.\

Jan 1, 1996

By D Tuazon, M Powell, M Ziemski, G D. Corder

Although mining companies have made broad corporate-level commitments to adopt sustainability, there continue to be problems when attempts are made to adopt higher-level sustainability aspirations and translate them into appropriate targets and methods at the more-specific operational level. The integration of sustainability principles into minerals processing operational decision-making processes has unique challenges that are not addressed adequately by current tools and methodologies, yet impacts from operational decisions can have longer-term effects realised at closure and rehabilitation.This paper describes a proposed methodology to achieve the integration of sustainability at the operational level through a systematic and rigorous process of identifying and qualifying sustainability issues and opportunities in an operation. The methodology, starting from a sustainability point of view rather than an operational one, guides the identification of process issues and opportunities by examining the operation, unit-by-unit, similar to a Hazard and Operability (HAZOP) process. Each issue or opportunity is qualified according to its measurability, scopes of impact and consequences so that it may be understood fully and the correct engineering problems are formed. Through improved decision-making to account for broader sustainability factors, operations can better address environmental and social expectations and pressures (both corporate and community, as well as immediate and in the longer-term), whilst still delivering on operational and business goals.The methodology has been tested with two case studies at minerals processing operations. At one site, the methodology identified a dust issue which had considerable business risks (loss of valuable product) compared to conventional engineering analysis processes. The other site also benefited from using the methodology as an opportunity to improve the operation of the milling and flotation circuits was identified. The opportunity not only showed a potential to improve operational efficiency, but also potential improvements in water and energy efficiency and a resulting increased resilience against water and energy supply risks. It was important to utilise the holistic approach of the methodology in the identification of opportunities at this site; the goals of the operation showed a strong coupling between water and energy issues which would be difficult to overcome using the operationÆs current organisational model, which deals with such issues separately of each other.CITATION:Tuazon, D, Corder, G D, Powell, M and Ziemski, M, 2012. A practical and rigorous approach for integrating sustainability principles into decision-making processes at minerals processing operations, in Proceedings Life-of-Mine 2012 , pp 233-242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By P Luo, J E. Danoczi, P Nakutnyy

Sensor-based sorting methods to remove waste or for upgrading ore prior to downstream metallurgical processing is becoming more prevalent for mining operations. X-ray transmission (XRT) sorters are a popular choice for mineral processing plants since they can sort a wide variety of minerals. XRT sorters pass high intensity X-rays through particles to generate images of varying greyscale, based on their effective atomic density. The ore sorter then mechanically separates the particles using algorithms based on the images. A popular test currently used to evaluate the amenability of the ore to XRT sorting is to pass the particles through the sorter and obtain the greyscale images showing mineralogical differences. This test provides information on the mineralogical heterogeneity between ore particles for their separation. However, it does not provide an understanding of the actual mineralogical composition of the ore or information pertaining to which other minerals may respond in a similar manner, nor does it provide liberation information. This paper describes a test that combines high resolution X-ray micro Computer Tomography (CT) combined with QEMScan to obtain information about amenability of ore to XRT sorting and to obtain valuable information that can streamline metallurgical testwork programs. This test also provides information relating to particle thickness and associated X-ray attenuation coefficients, desired mineral presence and mineralogical information relating to associated minerals and clays to assist with developing sorting algorithms. Combining the CT and QEMScan can address many limitations of the current method to determine whether XRT sorting technology is appropriate for particular ores. Mineralogy information from QEMScan can identify incidences of; mineral encapsulation, problematic clays, detrimental minerals as well as calibrate the greyscale values of CT data. Additional 3D CT imaging carried out on cores provides spatial information of the minerals within the ore and mineral grades.

Nov 10, 2020

By P B. Hills

Increasingly over the past couple of decades, the importance of understanding the in situ stress regime in underground hard rock mines has become accepted by all. Providers have responded to this requirement and various techniques for undertaking the measurements have been honed while others have slipped from use. It is a simple, though not inexpensive task to engage a provider to undertake the require measurements, and a comprehensive report will ensue. So, what has actually been obtained? What should the geotechnical engineer do next? What tools are necessary to do so? Regardless of the method of measurement, the report will describe the location of the measurement site and describe the basis of the methodology used in undertaking the measurements and a log of the measurement program. Finally, it will include the results, which should incorporate the normal and shear stress components of the full stress tensor. Ground control management plans (GCMP’s) and stress summary reports and spreadsheets prepared by site geotechnical engineers always include the magnitude, trend and plunge of the principal stresses. Remarkably few site-based summaries include the full stress tensor. This is a significant gap as the full stress tensor is vital for any further data manipulation. However, without the algebraic tools to undertake those manipulations, their value is diminished. This paper seeks to provide a checklist of ideas to be considered. It provides commentary on the options available to dissect the stress measurement report and ensure that the maximum possible value is derived from it. The manipulation and presentation of component stress data is also discussed. The various methods of stress measurement are not the focus of the paper but some of the strengths and weaknesses of them over which the site geotechnical engineer has some control, are highlighted.

Nov 29, 2022

By P J. Vardon, L A. van Paassen, Y Yao, A F. van Tol

Thin-lift atmospheric fine drying (AFD) is a technique used to dewater mine and oil sand tailings, which utilises both self-weight consolidation and atmospheric evaporation. The disposed layers undergo a cyclic drying and rewetting process due to precipitation and deposition of additional lifts on top of the dried layer. The current research aims to optimise the deposition process via use of a numerical model and realistic atmospheric conditions, including both periods of drying and wetting. The model is based upon water balance and includes large strain considerations. A number of material behaviours are characterised using empirical fitting curves based upon laboratory measurement of material characteristics, including both the shrinkage and water retention curves for drying and rewetting. The model is able to model multiple lifts, simulating field scale and realistic climatic conditions within timescales suitable for engineering practice (eg seconds or minutes). The model has been previously validated against controlled laboratory experiments and utilised to simulate field tests. A series of simulations are presented to illustrate the ability of the model to be used as a practical tool for the optimisation of a tailings deposition strategy.CITATION:Vardon, P J, Yao, Y, van Paassen, L A and van Tol, A F, 2015. The use of a large-strain drying and consolidation model to optimise multilift tailing deposits, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T Isaksson, J Anderson

The procurement process for underground construction contracts, in particular those contacts involving tunnel boring machines (TBMs), is subject to many complex and inter-related variables, including national and local politics, public policy, community involvement and media attention û as well as strict environmental and legal requirements. Other restrictions include the time available to adequately investigate geotechnical conditions and viable technical options to determine the best construction methodologies û including selection of tunnel boring machine characteristics and, those construction means and methods suitable for the specific geotechnical and environmental conditions. The latter are, most often, quite imperfectly understood. æGetting it rightÆ implies that an optimal configuration û of machine type, characteristics and associated methodologies û can be found and successfully implemented for a particular project. æFrom the beginningÆ implies that the lack of time issue can be successfully resolved. Within an international context this paper highlights a number of issues of concern which relate to tunnel procurement systems and the ways in which certain key processes are managed during planning, design and construction. The authors argue that there is considerable room for improvement in the way tunnelling projects are undertaken and an approach is discussed which has the potential for substantial gains in cost and schedule and reduction of risk. Savings, however, may only be fully realised if the new methods can be fully implemented by all parties involved. This, we believe, will require the rejection of ætraditionalÆ forms of management and procurement with associated changes in the roles and responsibilities of owner, engineer and contractor. Additionally, risk identification, assessment and mitigation are essential cost and schedule control process which have, to this point, been underutilised by the underground construction industry.

Jan 1, 1999

By Cutmore NG

The moisture content of iron ore is important in handling, stockpiling, transport and further processing operations. Typically these ores contain both `free' and `bound' moisture, the latter being moisture that is not removed in a conventional laboratory determination of moisture by air drying at 105¦C, and it is the free moisture that is important in dust control and ore handling. The CSIRO Division of Mineral and Process Engineering has previously developed and commercialised gauges, based on capacitance and microwave techniques, for the on-belt determination of moisture in coal and minerals. However, these gauges determine total moisture, and have a different sensitivity to free and bound moisture in the material analysed. Consequently, the accuracy of determining total or free moisture alone may be significantly affected by variations in the bound moisture content. An investigation has been carried out on the simultaneous determination of free and bound moisture in iron ore fines (

Jan 1, 1993

The Matakan Unit of New Ireland, Papua New Guinea is a highly fossiliferous lagoonal deposit containing numerous coal pods and lenses. The unit is strati graphically part of the massive reefal Lelet Limestone of Miocence age. These organic-rich sediments have a high hydrocarbon potential as evident from microscopical observations as well as Rock- Eval pyrolysis data. The coal is varied in regard to dominant macerals, vitrinite being predominant in some parts and pollen and spores present in sufficient proportions to constitute a cannel coal elsewhere. The highly fossiliferous carbo as Rock-Eval pyrolysis data. The coal is varied in regard to dominant macerals, vitrinite being predominant in some parts and pollen and spores present in sufficient proportions to constitute a cannel coal elsewhere. The highly fossiliferous carbonaceous sedimentary rocks associated with the coal are rich in pyrite expressed in the sulphur content (19.7 - 22.8%). A high primary productivity and anoxic sediment pore waters or just above sediment - water interface have given rise to sufficient organic matter accumulations to yield a potential hydrocarbon source rock. Atomic H/C ratios of the coals are between kerogen type III and type II mainly, expressing the mixed nature of the coal and that of the associated sediments is type II. Early generated hydrocarbons (exsudatinite) have formed from pollen exines filling the pollen cavities and in places filling micro- fissures in the surrounding vitrinite.

Jan 1, 1987

By J Shandro

This paper stems from recent multidisciplinary research between mining engineering and health researchers at the University of British Columbia and the University of Victoria, Canada. It considers the implications of a future state of sustainable mining development that places more emphasis on consideration of mine community health and sustainability within the definition of mine planning best practice. It reviews recently completed research studies on mining and other resource communities in British Columbia, Canada and a process undertaken by the research team to share research findings. It then examines the outcomes of this knowledge sharing process placing emphasis on the development of a more collaborative and enhanced mine planning process that integrates community- level indicators of health and sustainability to more effectively address mine impact-benefits. The paper concludes by discussing current initiatives that aim to benefit the mining industry, communities, and governments as they plan future mineral development projects.

Nov 22, 2011

By D Kentwell

For deposits where a full assay suite of elements/oxides is available and where several variables are critical to the evaluation of the deposit, it is desirable for the estimated block values of all elements/oxides to sum to 100 per cent of the weight per cent. This is difficult to achieve in practice and the estimation methods used need to be designed to minimise bias of the key elements/oxides by ensuring that block estimates are consistent with the individual assays and that the estimated totals are as close as possible to 100 per cent.This paper presents a case study of two domains within a magnetite hematite deposit, one with a high level of drilling classified as Measured and one with a lower density of drilling classified as Indicated. Several estimation methods were tested to evaluate their ability to maintain consistency of the proportions of each element/oxide and sum to 100 per cent. The following methods were evaluated: ordinary kriging, co-kriging, inverse distance and min/max autocorrelation factors (MAF) all as implemented in the Geovariances Isatis software.The comparisons showed that the MAF method produced the most robust estimates in terms of block totals and that grades and tonnages at the reporting cut-off were not significantly different between methods. At an individual block scale all methods produce artefacts that are less than desirable but can only be remedied by additional drilling.CITATION:Kentwell, D, 2015. Comparison of min/max autocorrelation factors, kriging, co-kriging and inverse distance block totals – a magnetite hematite case study, in Proceedings Iron Ore 2015, pp 465–474 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Accurate geometric models of orebodies establish the framework for reliable mineral resource estimates that provide a basis for further exploration and mine planning, as well as for financial models that ultimately determine the economic viability of a deposit. Traditional, explicit geometric modelling techniques that are utilised for resource modelling by the general mining software packages, such as MineSight«, involve manually digitising interpreted ore outlines that must be carefully linked to create valid geometric solid models. An alternative, implicit modelling method, employed by LeapfrogTM software relies on a fast method of global interpolation, which offers several advantages over traditional modelling techniques. Although previous case studies have documented the relative efficiencies of the two approaches, the accuracy of the two methods has not been previously quantified and compared. This study quantifies the accuracy of solid models created using explicit and implicit methods, and compares the differences between the models. Solid models of the Doris Hinge vein gold deposit (located in the Hope Bay district, Nunavut, Canada) are constructed from preliminary and follow-up drilling data using both modelling techniques. The accuracies of the solid models generated using preliminary drilling data are determined by measuring the 3D distance between the surface of the models and the actual contact location defined by the follow-up drilling data. Additional comparisons based on volume, cross-sectional area and surface differences were made between both phase 1 solid models and solid models constructed from phase 2 drilling information. The overall results of this study find that the MineSight« and LeapfrogTM solid model accuracies are virtually the same, and that their volume, cross-sectional area, and surface differences are comparable. This study concludes that the implicit modelling technique generates accurate solid models that can be used in place of explicit models as ore shells for resource estimation in certain circumstances.

Jan 1, 2006

By J Knoblauch, D, P J. J Strobos, C Foggo

The Sally Malay Project is located 120 km north of Halls Creek in the eastern Kimberley region. Since commissioning, ongoing improvements on the plant have resulted in recoveries now greatly exceeding the initial design targets. The continual optimisation endeavours of the Sally Malay metallurgy department included an automation project that was done in close collaboration with Mintek. In this team effort, several problem areas were addressed and the FloatStar advance control system was successfully commissioned to stabilise and optimise the flotation circuit. The remote location of the Kimberley Nickel Mines operation, fly-in, fly-out roster and the current mining boom makes the acquisition of experienced flotation staff difficult. The implementation of an automated flotation control system reduces this burden and contributes to the training of inexperienced staff. This paper illustrates not only the process control improvements achieved as a result of the installation of the FloatStarÖ advanced control system, but also how it has assisted operational personnel with their understanding of the process.

Jan 1, 2006

The character of alluvial gold deposits presents severe difficulties, and sometimes limitations, on the extent to which metallurgical efficiency can be measured. Very little monitoring of metallurgical performance is practised. An indication of performance is often extracted from the comparison of production to the estimate. This is a dubious practice. The recovery efficiency of conventional practices, viz sluices, tables and jigs, falls off sharply below 0.2 mm. Field evaluation procedures tend to simulate these conventional practices. Thus the presence of fine gold may not be detected, particularly if obscured by clay. There is increasing evidence that fine gold could, in places, be present in sufficient concentrations to be economic. Most gold in paleoplacers is finer than 0.1 mm. There are established practices elsewhere in the mineral industry that may physically recover gold down to 5 microns in size and which could find application for fine alluvial gold.

Jan 1, 1984

By S McKnight, L Koroznikova, J Begelhole

"This paper outlines a simple methodology for iron ore characterisation. Iron ores commonly contain a range of iron oxides with varying iron content along with generally minor quantities of lighter silicate gangue phases, giving rise to density variations. Companies tend to rely on heavy liquid separation (HLS) in the evaluation of samples arising from exploration, mining or metallurgical processes. Heavy suspension separation (HSS), a simple laboratory technique of density fractionation, employing suspensions of fine tungsten carbide (WC) particles in lithium heteropolytungstate (LST) solutions, can be used in the evaluation of iron ore.As part of Arrium Mining’s program to improve its knowledge of ore types being processed in two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed and geometallurgical evaluation for the OBPs has become a major focus.Metallurgical evaluation of the hematite ore ultra-fine size fraction, formally treated as waste but now upgraded by HSS, is a part of Arrium’s program to improve recovery.The HLS method for iron ore characterisation is not generally used as part of routine iron ore feed metallurgical evaluation due to the expense, toxicity and time-consuming nature of the technique. Results show that the HSS method for iron ore characterisation can achieve low-cost, low-toxic separation and can be used on-site to improve turnaround time of results (Begelhole, Jasper and Koroznikova, 2013).Arrium have applied this technique successfully for the past three years to progress process improvement for the two OBP as well as to assist Arrium’s on-site laboratory services, Bureau Veritas in Whyalla.The main objective of this program has been to further develop the HSS procedures using a low-toxicity, high specific gravity (SG) suspension; LST and WC as the dense medium for metallurgical evaluation of ultra-fines.A suspension of a particular density will separate iron ore into two products: a sink fraction (denser iron oxide – hydroxide particles) and float fraction (silicate – iron ore composite particles). A theoretical grade and mass recovery can be calculated, and a grade – mass recovery curve can be constructed for iron.Metallurgical evaluation of the plant feed ultra-fine size fractions are used to improve efficiency of an upgrading plant process. This type of characterisation can be used to prepare feed piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved.CITATION:Koroznikova, L, Begelhole, J and McKnight, S, 2016. Characterisation of Low-grade Hematite Ore Ultra-fine Size Fraction Particles by Heavy Suspension, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 327–334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Song Yongxue

During the design and operation stages of a block caving project, a large amount of research and development work has been undertaken in the Tongkuangyu Copper Mine. This paper presents the research achievements from these studies, including a rock mass quality evaluation method, cavability prediction, fragmentation evaluation, caving mechanisms, a computerised production scheduling model and the optimised draw control system. The main features of the block caving system in the Tongkuangyu Copper Mine are also discussed.

Jan 1, 2000

The King River Power Development on the West Coast of Tasmania has involved the storage of the waters of the King River in the new Lake Burbury and their diversion through a 7 km tunnel to a 144 MW power station. The last kilometre of this tunnel descends through 160 m under a ridge before emerging from the bank of the King River at the power station site. The decreasing cover over the tunnel as it approaches the power station meant that a steel lining was required in the last few hundred metres of the tunnel. This paper describes the geotechnical investigations which were carried out to establish the necessary length of the steel lining.

Jan 1, 1993

By Lorenzen L

In South Africa, as in many other countries, the young engineering graduate is promoted quite soon to a management position where he uses less technical skills and more people-oriented skills. In the standard undergraduate curriculum for engineering, little attention is paid to the non-technical issues of the profession. An undergraduate course in management techniques cannot be a substitute for a MBA or Masters degree in engineering management, but can at least create an awareness of the practical problems facing the engineering manager. The aim of this paper is to provide an outline of such a course structure at the University of Stellenbosch. A survey is also presented on management training in the South African and Australian mineral industries. Feedback from students and graduates indicates that the fresh graduate does not fully appreciate the value of such a course until he/she achieves a position of responsibility after two or three years. Nevertheless, the management course appears to be successful in widening the perspectives of the engineer. As explained frequently in management journals, the technically oriented person (the engineer) has a convergent thought pattern, which could be in conflict with the more divergent thought pattern of the top, personnel or marketing manager. It becomes increasingly imperative for the young minerals engineer to be externally oriented instead of the traditional internal focus of engineering. The engineer should not only be aware of environmental issues in the technical design and operation of plants, but should also understand the inter-relationship between public relations, political pressures and environmental perceptions vis-d-vis technical facts.

Jan 1, 1993