Search Documents

By C J. Unger, T Baumgartl, C J. Bond, P Sabourenkov, V C. Glenn

Social licence to mine is influenced by society’s perception of the mining sector’s ability to effectively rehabilitate mined land and for governments to appropriately regulate that process for the broader community benefit. In Queensland, Australia, many mine rehabilitation personnel working for active coalmines, as either staff, consultants or contractors, belong to the Central Queensland Mine Rehabilitation Group (CQMRG). The CQMRG was established 23 years ago with the aim of sharing informal knowledge related to practical aspects of rehabilitation in order to leave as positive a legacy as possible from mined land. This voluntary group of professionals also includes members from regulatory agencies and civil society. Within the dynamic regional mining environment, mine rehabilitation professionals benefit from sharing their informal knowledge.CQMRG is currently a group in transition. Mining boom and downturn cycles have exacerbated the loss of accumulated knowledge in the core CQMRG membership due to rapid changes in personnel at mines in the region. Additionally, some of the most experienced CQMRG-affiliated rehabilitation practitioners are approaching the end of their careers and want their valuable and less formal knowledge retained. This paper discusses the development of a research project that emerged in response to the anticipated loss of several decades’ worth of valuable knowledge as rehabilitation practitioners in CQMRG left the region or the workforce.CITATION:Unger, C J, Bond, C J, Baumgartl, T, Glenn, V C and Sabourenkov, P, 2016. ‘MRC-wiki’ – a mine rehabilitation and closure knowledge management tool for Central Queensland coalmine practitioners, in Proceedings Life-of-Mine 2016 Conference , pp 39–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By E Corpuz, J Weissman, S Winter, R Evans

The surface-to-inseam (SIS) directional drilling technique has been utilised at Oaky Creek Coal for more than a decade to predrain both the Oaky No 1 and Oaky North mining areas. The cumulative drilling program constitutes a total of 140 lateral and 200 vertical holes, and 405 km of lateral drilling.The use of SIS gas drainage has been successful with the following site-specific benefits being recognised:ability to drain German Creek seam gas contents to residual gas levels of new mining areas within an 18-month period from commencement of well productionstructural geological verification of the mine design well in advance of development mining occurring in an areaability to conduct successful predrainage of the overlying Aquila seam to reduce subsequent goaf emissions.Appropriate and up-to-date geological knowledge during the design and drilling process is a significant influence to achieving success. Vertical production wells need to be located in a position that is most effective to remove water from hole. The lateral hole should not include intersections with significant geological structure.SIS drilling provides continuous seam roof/floor data to help define seam geometry and locate geological hazards with high accuracy. In faulted ground and with variable seam gradients, SIS data can resolve geological ambiguities from seismic sections and enhance seam correlation that would otherwise be available only from discrete and closely-spaced infill vertical exploration drilling.Here, we review some examples of SIS configurations and practice to highlight key learnings in drilling long inseam holes (up to 1900 m per arm) ahead of development and mining. Aspects on prerequisites, evolution of network design, tolerances and drainage outcomes in a variety of geological situations are discussed as technical basis towards a viable and effective SIS drilling program.CITATION:Corpuz, E, Evans, R, Weissman, J and Winter, S, 2015. Surface-to-inseam (SIS) drilling at Oaky Creek coal mine – SIS design aspects and drilling environment, in Proceedings The Australian Mine Ventilation Conference, pp 93–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Garland W

Access to geoscience reference informa- tion including mining and mineral processing has increased considerably in the last five years in Australia. This has been due principally to the use of computer-based information storage and retrieval systems. The main reference data base for the mineral and petroleum industries and disciplines in Australia is the Australian Earth Sciences Information System (AESIS), cooperatively developed and coordinated by the Australian Mineral Foundation (AMF). AESIS is created on the CSIRO computing network (CSIRONET) which has a CYBER 76 host computer located at the CSIRO Division of Computing Research (DCR) at Canberra. Data entry was until recently carried out by AMF using a dedicated line through the Adelaide CSIRONET node to the CYBER 76 interactive system. Data entry is now done directly at the AMF on a DEC PDP 11/44 mini computer that is also a host work station on CSIRONET. Data collection via magnetic tape media input from other computer-based systems is under development. The software used for data entry and management of the data base was developed by CSIRO CILES Systems Development Group. For public interactive online use the AESIS data base is transferred by tape to AUSINET - the Australian information net- work run by ACI Computer Services, Melbourne, where the data base is converted to a form suitable for the IBM STAIRS software. CSIRO facilities at DCR Canberra are used to produce computer type-set camera ready products and output in microform, on magnetic tape or as graphic display. Keywords: Earth sciences information, Computer applications, Information storage and retrieval, AESIS, Data bases, Australia.

Jan 1, 1983

The population and the per capila consumption of mineral resources have both grown dramatically during the century past. It is argued that growth will continue through the century ahead but that the magnitudes of undiscovered resources are probably adequate to meet demands. The challenge that the mineral explorer of the future will face is finding deposits beneath several kilometres of barren rock.It is further argued that the principal challenge that society will face in the century ahead is the amelioration of environmental stress.

Jan 1, 1993

The large rotary blast hole drills for hole sizes of 250 to 375 mm in diameter have been utilized by large open pit metal and coal mines for production drilling all over the world. The design of such rotary drills is in most cases about two decades old and it has not been done much in order to apply a modern technology on rotary drilling. The most modern large rotary drill, Tamrock RI 10, consists of an advantageous rotary head with a squirrel cage AC motor controlled by a frequency converter, a beneficial mast structure with a possibility for inclined drilling, hydraulic driven, independent crawlers, and a modern ergonomic cabin to provide a comfortable working condition for the oper- ator. Several automatic features are available as options. The rig has been designed to be operated by one man only. With this modern rig the produc- tion rate can be increased and production cost kept on a low level.

Jan 1, 1989

By I H. Wilson

After decades of turmoil, Rwanda launched its Vision 2020 in 2000 aimed at reconstructing government and addressing poverty. Implementation focused on the agricultural sector, infrastructure and education. Later economic development and poverty reduction strategies recognised that expansion of tantalum, tin and tungsten mining could potentially diversify Rwanda’s economy and improve the balance of trade. In 2005, comprehensive environmental legislation requiring environmental impact assessment for all new mines was introduced. Since 2006, government-operated mines have been privatised and illegal artisanal miners encouraged to form cooperatives. The government passed a new Mining and Quarry Exploitation Law in 2008 and approved a new Mining Policy in 2010. This policy was influenced by the Africa Mining Vision (AMV), which the African Union approved in 2009 to ensure African countries obtain reasonable benefits from exploitation of their mineral wealth. The Rwandan mining industry has grown significantly over the last five years and the second economic development and poverty reduction strategy, released in September 2013 forecasts a further three-fold increase in production in the next five years. The strategy prioritises the mining industry and proposes new legislation, better information, greater transparency, encouragement to investment and use of best environmental and technical practices. It also proposes that Rwanda develop a ‘green’ mining sector featuring a ‘model’ mine that is fully funded through green investment and incorporates renewable energy systems, water treatment systems, forestry schemes and local training. Many international development partners have contributed to the current legislative framework and are monitoring environmental and social performance of mining in Rwanda. Local communities have generally benefited from mining and the new mines show improved environmental performance. The major challenges are dealing with the legacy of past haphazard mining practices and establishing linkages between the mines and local industries to create broader economic development.CITATION:Wilson, I H, 2014. Rwanda and the Africa mining vision, in Proceedings Life-of-Mine 2014 , pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By C D. Rose

"The primary objective of this paper is to demonstrate a different approach to predicting and verifying mechanical sampling system precision. Early in the year 2011 an experiment was conducted to evaluate the sampling precision being obtained by a three-stage falling-stream mechanical sampling system for coal owned and operated by Peabody Energy. This system collects samples from lots averaging approximately 14000 t being loaded onto rail cars at a flow rate averaging about 9000 t/h. In phase 1 of the experiment, a total of 60 increments were collected in a two day period at preassigned intervals using a cross-belt sampler located on a conveyor belt feeding a silo upstream of the sampling system under evaluation. Coal variability parameters were calculated from the resulting laboratory analysis data using the gauge-invariant fractal model developed by the author.Estimates of precision of the three-stage system as a function of the number of increments were calculated using the variability parameters determined in phase 1. In phase 2 of the experiment, duplicate samples of 30 lots of coal were taken by the three-stage sampling system, enabling calculations of the precision being achieved by the system. Phase 2 precision estimates are in reasonable agreement with those of phase 1. Conclusions drawn from the experiment include the following: Experimental variograms or the equivalent correlograms are essential in understanding sampling issues and for designing a sampling system to meet specific precision requirements. Consensus coal sampling standards provided by ISO and ASTM may be improved by treating all stages of a mechanical sampling system as æsamplingÆ rather than considering downstream sampling stages as æsample preparationÆ, to be treated in a separate part of the document. The coal industry would profit from use of methodology for routinely monitoring the overall measurement precision and the precision of the individual components of measurement: sampling, sample preparation and laboratory testing. This would not only give necessary credence to the measurement results but would also no doubt, lead to more efficient sampling system designs.CITATION:Rose, C D, 2012. Evaluation of precision being obtained by a three-stage sampling system for coal, in Proceedings Sampling 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By Leahy G. J, Moxon N. T, Nicol S. K

Experimental work is described in which extremely dilute aurocyanide liquors are treated with novel surface-active complexing agents to produce a hydrophobic aurocyanide species. Subsequent aeration of these liquors causes accumulation of such species at the air-water interface and the aurocyanide complex is transferred to a froth concentrate. A detailed performance assessment of this process is made and this knowledge used in the design of a pilot plant facility. Early results indicate the feasibility of the selective recovery of aurocyanide ions from reclaimed residue dam water (approximately 0.2ppm Au) with upgrade ratios of the order 180:1. A further study was made applying ion flotation to the recovery of gold from a carbon-in-pulp (CIL) feed liquor (approximately 1.0ppm Au). The probable economics of this process compared to conventional CIL processing is also described. Successful development of countercurrent ion flotation for concentrating solids-free gold solutions may offer a lower cost alternative to existing gold ore processing technologies, or in more secondary applications such as concentrating dilute gold solutions or heap leach runoff. The technology may also have more generalised applications to other heavy metal process- Ing.

Jan 1, 1991

By M Uceda, E Guerra, Y Choi, J L. Shepherd

In this paper we describe the leaching characteristics of pure gold in thiosulfate solutions that contain a known chelator; meso-2,3-dimercaptosuccinic acid (DMSA). The interfacial and chemical characterisation of the system was accomplished using both electrochemical methods and inductively coupled plasma mass spectrometry (ICP-MS) analysis after pure gold samples were exposed to solutions composed of 65 mM Na2S2O3, 1 mM NaOH and a range of DMSA concentrations. In the absence of DMSA, cyclic voltammetry revealed the onset of thiosulfate mediated gold dissolution, the degree of which was reduced at more positive potentials due to the formation of oxidised thiosulfate products on the gold surface. The addition of small amounts of DMSA (<10 ¦M) to the electrolyte resulted in minor changes to the voltammograms indicating a subtle interaction of the additive with the gold surface that may improve leaching. However, at higher concentrations of DMSA (up to 100 ¦M), electrochemical evidence suggests the formation of new oxidation products in solution as well as the formation of more compact monolayers of DMSA on the surface, which contribute to partial repassivation of the surface. The influence of DMSA on thiosulfate leaching of pure gold electrodes at the open circuit potential for a period of 90 minutes was tested and the corresponding gold leaching performance evaluated with ICP-MS analysis. Our data shows that small amounts of DMSA (1 ¦M) doubled the amount of total gold in solution when compared to the same study in the absence of the additive. However, higher concentrations (5 ¦M DMSA) reduced the overall amount of dissolved gold. These results may point to a mechanism where small amounts of DMSA improve leaching by adsorbing onto the surface in a highly defective monolayer that partially blocks or disrupts the formation of passivation products caused by thiosulfate oxidation, but excess DMSA can limit the leaching process itself by forming too coherent a monolayer on the gold surface.CITATION:Uceda, M, Choi, Y, Shepherd, J L and Guerra, E, 2013. Investigating the influence of meso-2,3-dimercaptosuccinic acid on thiosulfate leaching of bulk gold electrodes, in Proceedings World Gold 2013 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A Roseman, T Gruber

Traditional methods for installing gaskets for segmented bored tunnels have relied upon different bonding procedures with adhesives that carry a series of disadvantages to segment producers. Fixation of the gaskets into the concrete segment as part of the casting procedure has been developed over the last 20 years and has emerged as an economical solution to produce high-quality tunnel segments for various technical tunnel applications. This paper investigates the advantages of using anchored gaskets, the different tunnel systems that employ anchor gaskets and reviews the first anchor gasket project; the Lee Tunnel and analyses how segment production efficiencies are gained.CITATION:Gruber, T and Roseman, A, 2014. Use of anchored gaskets in segmented bored tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 253–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Gerards, M Steinberg, T Graham

The quality and quantity of Australia’s secondary deposits, which include tailings streams and tailings dams, are higher than most countries’ primary deposits. In addition, these secondary deposits have already been mined and processed, meaning that the recovery of high-grade product requires low capital and operating costs.The most widely used process for the recovery of these valuable fine and ultra-fine hematite iron particles is the wet high-intensity magnetic separation technique, originally developed by Dr Jones over 55 years ago. Many of the original machines are still working today.The aim of this paper is to demonstrate the capabilities in terms of grade and yield of using sophisticated magnetic separation modules. All results and figures are obtained from test work and design and engineering work with material from the Pilbara. In addition, consideration is given to dewatering of iron ore product and tailings.Two types of tailings have been identified for processing. Firstly, tailings that have already been deposited in a tailings storage facility, and secondly, live tailings streams from an existing wet iron ore beneficiation plant. In both cases, the technical and practical results are shown along with relevant flow sheets and plant layouts. Finally, this paper highlights the total predicted power and water consumption, capital requirements and projected operating expenses.The results show that the operating costs are significantly lower than the mining and processing operations that are required for an equivalent amount of iron ore. The recovery of iron depends on various factors but is within the 30–50 per cent range at an equivalent grade to the mainstream product. Another significant benefit is that the magnetic separation process is water positive, meaning that water is released rather than added in the process.The processing of the Pilbara’s secondary deposits will therefore result in an overall reduction in operating costs, an increase in product yield from a plant, extend the life-of-mine and offer environmental benefits by reducing the tailings footprint and water usage.The quality and quantity of Australia’s secondary iron ore deposits and tailings are such that many other countries would judge these as equivalent to primary deposits. Furthermore, these tailings are already mined, available and liberated to such an extent that the recovery of a valuable product is highly economical in terms of capital expenses and operating expenses.CITATION:Steinberg, M, Graham, T and Gerards, M, 2015. Recovery of iron ore fines and ultrafines from tailings by using wet high-intensity magnetic separation – JONES WHIMS, in Proceedings Iron Ore 2015, pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Bof J, Lowe S

BHP's newest colliery on the Southern Coalfield Is Tower Colliery. It is situated near Wilton some 60 kms south west from Sydney. It commenced its operations in 1978 and since that time has experienced considerable roof problems. In its eight years of operations, production has been 936 687 tonnes to December 1985. To a certain extent this is a reflection of the ground control r,,b1cros present in the colliery. paper out Iines the signif mt g,, logical features that are known to exist in the colliery and their influence on roadway development. Faulting has hindered the mine's development and an igneous intrusion has had outhursting associated with it. The prevailing roof rock has also had an impact on the roadway conditions. The paper will look at intersection deformation in present workings. Extensometers have been installed in these areas and provide measurements to verify visual observations. The results show a significant increase in roof movement as the roadway is developed from a single heading, to a T-intersection and then Into a four-way intersection.

Jan 1, 1986

The outlook for suppliers of energy to the expanding economies of the Pacific Basin region is essentially positive, but particularly for exporters of high quality steam coal. This paper argues that economic growth in the Pacific Basin region has exceeded world economic growth for some years and that this will continue to be the case for the next decade at least. It looks briefly at the link between economic growth and energy demand and at the relationship between energy demand and the demand for electricity.Changing preferences in fuel mix for electrical generation in the region are noted and tentative forecasts made about variations in this mix. The pros and cons of various forms of fuel used to generate electricity are considered from the point of view of the consumer.

Jan 1, 1990

The deep seafloor in Papua New Guinea's proposed Exclusive Economic Zone appears to be a gold-rich province in the same sense as the territory above sea level. Two significant sites with polymetallic massive sulphide deposits forming today are known on neovolcanic ridges in the Manus Basin. Their high precious metal contents have led to renewed interest in the issue of exploiting seafloor mineral deposits. The prospects of finding other, possibly larger deposits in the region appear substantial. This paper reviews current data on seafloor deposits in Papua New Guinea (PNG) and raises some issues relating to future commercial exploration and mining of the sea floor. One of the known PNG deposits could become a prime candidate for the trials needed to develop technology, establish costs, and minimise environmental impact.

Jan 1, 1994

By Hermulheim W

In the Federal Republic of Germany hard coal is mined underground only. The coal mines reach down to 1 500 m deep, recently having an average depth of 900 m. The commonly used winning system is long- wall mining with face lengths up to 250 in. The gate roads, which separate the seam into single panels, have an average length of one kilometre with a cross- section up to 20 m2. These single entries are usually supported by yielding steel arches. The installation of steel arches can hardly be mechanized. The choice of heavier support, caused by increasing depth and roadway cross-section, results in high cost for labour and material in gate roads. Furthermore, the heavy steel arch is acci- dent-prone, not only during installation but also during transportation and ship- ment. Rock bolts combined with a suitable lagging offer a way of mechanizing support work in headings. The aim is to decrease cost and to increase mine safety and pro- ductivity. Over the last ten years, 50 km of gate roads have been reinforced by a combination of rock bolts and weld mesh. Nevertheless, there are still differing opinions on the feasibility of rock bolting in gate roads. In Germany a long tradition and experience with steel arch support exists, whereas the function of an anchorage is a closed book to miners, preventing this new technique from spreading more quickly. Advantages and shortcomings of both steel arch support and rock bolting are compared. The experience with rock bolting up to now is reported. Possible improve- monts arm discussed.

Jan 1, 1986

By A Salama, J Greberg, B Skawina

In today’s underground mass mining, the orepass is an important part of the infrastructure as it connects two or more mine levels and is used for conveying or storing large amounts of material. One of the main risks related to an orepass is when operational or structural failure occurs, leading to long-term loss of functionality. Developing or rehabilitating an orepass when major failure has occurred is a time-consuming and expensive operation, and the risk of a long-term orepass loss motivates the development of alternative transportation strategies to ensure the continuation of smooth operations in large underground systems. The study presented in this paper has been done at the Loussavaara Kiirunavaara AB Malmberget mine in Sweden, where iron ore deposits are being extracted using sublevel caving. The study analyses the transportation system in one of the mine’s orebodies using discrete event simulation, with a focus on maintaining ore transportation in the event of the loss of an orepass.CITATION:Skawina, B, Greberg, J, Jonsson, K and Salama, A, 2016. Orepass loss mitigation approach in Malmberget mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 617–622 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Barlow S

The Kelian Gold mine project won two excellence awards from the Victorian Division of the Institution of Engineers, Australia. It was a challenging project, fast tracked in a remote and inhospitable tropical environment. The creation of a profitable and efficient mine was a significant engineering and project management achievement. The difficulties encountered and the way they were managed provide valuable lessons. These include the importance of sufficiently detailed engineering in all aspects of the job to enable the best estimates possible to be prepared during feasibility studies, the need to prepare the project scope and execution plan with disciplined and rigorous attention to detail by a highly experienced team and the value of identifying, assessing and mitigating risk and uncertainty during execution. The practical benefits of applying these lessons were demonstrated in the successful management of technical uncertainty on the recent diversion of the Kelian River to allow the expansion of the Kelian mine.

Jan 1, 1997

Physical model testing at Bergbauforschung is done in two rigs, a roadway rig and a longwall rig. The loading of such models, in scale relation to the con- ditions in the collieries provides valuable guidance to the probability and nature of failures, and thus to support requirements, in structural, roofbolts and self- auvancing supports. The success of such modelling when related to subsequent underground designs put to use suggests that such methods of investigation could be extended to pillar extraction problems also.

Jan 1, 1974

By Nag D. K

King Island Scheelite is a wholely owned subsidiary of Peko-Wallsend Ltd. The company works two underground mines near the southern end of King Island at the western approach to lass Strait, 240 km south of Melbourne. (See ^igure 1).

Jan 1, 1981

By M Medina, J Alexander, R J. Longey

Capricorn Copper Pty Ltd (CCPL) are operating the Capricorn Copper Mine located at Gunpowder, Queensland. As current holder of the environmental authority for the site, CCPL have obligations to rehabilitate areas of the mine that are no longer operational and have the potential to cause/contribute to environmental harm. CCPL sought a voluntary Transitional Environmental Program (TEP) to provide an agreed program of works to cap and rehabilitate the former Mammoth Tailings Storage Facility. The voluntary TEP contained conditions that were required to be met, to reduce the potential for environmental harm from the facility. The former Mammoth Tailings Storage Facility commenced use in the early 1970’s, and is an unlined valley in-fill structure, contemporary in design compared with other such approved structures of the era. The decommissioned Mammoth Tailings Storage Facility, now known as the Old Tailings Storage Facility (Old TSF), has been a legacy source of contamination due to the existing capping not meeting modern cover criterion, and allowing oxidisation and infiltration to the underlying acid forming tailings resulting in Acid and Metalliferous Drainage (AMD) from the facility. A cover design for the Old TSF, and other mine waste storages onsite that required clay capping, had been proposed by previous operators. Under the TEP cover design phase, it was identified that a key constraint was the lack of significant quantities of low permeability clay onsite. The lack of available clay prompted the consideration of alternate lining materials for the Old TSF, with a Bituminous Geomembrane Liner (BGM) being adopted as the preferred alternative. The BGM compared favourably with clay-based materials on seepage analysis, and led to other benefits by eliminating the need for borrowing clay off site, reducing the site’s environmental footprint, and reducing construction time. The BGM cover system on the Old TSF is being monitored with the intent to use this as a case study to confirm expected performance, enabling the cover design to potentially be adopted on the remainder of the site’s mine waste storages that require capping.

Jul 1, 2021