Search Documents

By T. Vasilos, J. T. Smith

THE mechanism of pressure sintering, or hot pressing, for ceramic materials, has been investigated by several researchers.1-8 Plastic flow has been suggested as the rate-determining mech-anism1,2 while grain boundary sliding3,4 and fragmentation processess have been found controlling in other studies. Vasilos and Spriggs5,6 have reported that pressure sintering occurs by a diffusion-controlled mechanism. For the pressure sintering of metals, investigations with lead7 and with tin6 have not identified the operative mechanism during consolidation of these powders. This note reports the results of a pressure sintering study initiated to determine the mechanism controlling the densification of spherical copper powder. Temperatures of 300°, 400°, 500°, and 600°C at 2500, 5000, 7500, and 10,000 psi pressures were investigated. The copper powder for this study was obtained from Metals Disintegrating Co., Elizabeth, N.J. The minimum purity was reported to be 99.9 pct. The powder size was -325 mesh and a lineal analysis showed the average size to be less than 1 p. An alumina die body and punches were employed. Graphite spacers were placed between the copper powder and the punches before pressing. It was expected that the graphite would form carbon monoxide with any entrapped air and form a reducing atmosphere within the die cavity. This condition was generally realized during pressing although a minor amount of oxidation occurred at 500" and 600°C. The oxide particles were located randomly in the pressed samples and were not considered to influence the densification process. Calibration tests showed the temperature of the copper pellet to be about 20°C less than the die wall temperature, probably resulting from heat losses through the punches. This difference was compensated during the experimental pressing operations. The hot pressing equipment employed for this work has been described by Spriggs et a1.9 and was calibrated with a Baldwin-Lima-Hamilton load cell. Travel of the punches was monitored with a dial indicator showing increments of travel to 0.0005 in. Relative density was calculated at selected time intervals for a known copper weight, punch travel, and die diameter. The accuracy of this calculation was *1 pct. Average grain size after hot pressing was obtained by lineal analysis. Typical densification curves are presented in Fig. 1 and Fig. 2 where relative density is plotted vs log time as a function of applied pressure for the 300" and 600°C pressure sintering temperatures, respectively. The curves for 400" and 500°C were similar to those at 300°C and consequently are not shown. The curves at 300°C as well as 400" and 500°C do not show an end-point or limiting density for a particular applied pressure. At 600°C, a density in excess of 95 pct of theoretical has been reached such that further densification is extremely slow for the 5000, 7500, and 10,000 psi pressures. It is suggested that further densification at these pressure levels may be retarded or prevented by discontinuous grain growth, by entrapped gases, and by other microstructural limitations as described by Cob1e.10 The curve for 2500 psi hot pressing pressure is a straight line over the time interval although a slight change in slope may be occurring at the last time intervals. The plastic flow models,1,2 derived for hot pressing, predict the existence of an end-point (or limiting) density dependent on the yield point of the material at the temperature of interest. The yield stress of copper at a 0.005 strain level has been

Jan 1, 1965

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

Jan 1, 1968

By E. A. Holbrook

MINING Metallurgy, and Petroleum Engineering department in our colleges are facing a crisis; indeed, conditions that threaten their very existence. Unless the Army, Navy, and War Manpower Commission change their present policy, within two years mineral industries education as now carried on will die, because no ablebodied students will be left in the course. If this is the decision of our responsible governmental agencies we of the mining schools must perhaps accept it as a war measure. It might be well however, for the executive of our mining metallurgical, and oil companies to look ahead a, to where they are to recruit a supply of young technically trained engineers. You can no more operate a mine, a steel plant or an oil company without trained engineers than you can operate a battleship without mechanical and electrical engineers.

Jan 1, 1943

[Aamot, Olav Crone, (M'29) Chem. Engr., Elektrokemisk, Raadhusgt. 23, Oslo, Norway. Abadilla, Quirico A., (M'38) Min. Engr., Dir. Bureau of Mines, Manila, P. 1. Abbott, Agatin, (J'40) Asst. Geol., Trench Mine, Patagonia, Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Tennessee Coal Iron & R.R. Co., 1642 Brown Marx Bldg., Birmingham, Ala. Abel, Raymond L., (M'28) Prof., Chem. Engrg., Univ. of Pittsburgh, Pittsburgh, Pa. Abel. Walter D., (M'32) Min. Engr., Div. of Corporations, State of Calif., 403 California State Bldg., Los Angeles, Calif. Abele, Louis T., (M'31) 4800 Patterson Ave.. Richmond, Va. Abell, Leo M., (M'31) Research Met., Mount Morgan Ltd., Mount Morgan, Queens., Australia. Abenius, Hakan V., (M'37) c/o Falu Gruva, Falun, Sweden.]

Jan 1, 1940

[I-Institute of Metals Division PAUL D. MERICA, Chairman ZAY JEFFRIES, Vice-chairman W. M. CORSE, Secretary General Committee ROBERT J. ANDERSON H. C. JENNISON L. W. SPRING WILLIAN K. FRANK DAVID LEVINGER R. L. SUHL J. R. FREEMAN, JR. PAUL McKINNEY R. F. WOOD]

Jan 1, 1928

By John W. Langley

In the summer of 1888 it was the fortune of the writer to present the subject of the desirability of establishing a set of samples of steel, which should be analyzed with extreme care, in order that they might become standards to which scientific and commercial analyses of iron and steel could be subsequently referred; also, that greater uniformity in the results of analyses might be brought about, since these standards would bear towards analytical methods somewhat the position which the original units of weight and length, the gramme and meter, or the pound and yard, preserved in Paris, London, and Washington, do to the mechanical arts. The plan met with hearty co-operation, with the result that com mittees were appointed in Sweden, Germany, France, England, and America, to receive the material and to see that the necessary au alyses were executed. In England, the British Association for the Advancement of Science appointed a committee, which subsequently published a plan

Jan 1, 1891

By William Mikulas

LITTLE work has been done in the field of the nickel-tin binary system. The complete diagram has been investigated on two occasions, but the results are in very poor agreement. The structure of a compound NiSn, and the solubility of tin in nickel have been determined by X-ray methods. Several investigations have been made of the liquidus curve, and the compositions of the eutectics have been determined. A study of the literature, however, shows that there is no satisfactory agreement between the data presented in the various papers. The present investigation was undertaken in an attempt to determine the equilibrium conditions, and to correlate X-ray with metallographic data. The equilibrium diagram was determined by thermal and metallo-graphic means, and the solubility of tin in nickel further investigated with X-rays. Powder diagrams were made of the intermetallic com-pounds, and three of the structures were partly determined. No attempt was made to determine the range of homogeneity of the inter-metallic compounds.

Jan 1, 1937

George E. Collins, Nacoochee, Ga. (communication to the Secretary): The results tabulated below were obtained at the Reynolds mill, White county, Ga. They were noted, not with a view to investigating the point discussed by Mr. Clark, but in course of a test on a working scale to determine the com parative saving from a given free-milling ore on copper and silvered plates respectively. In every case the bullion assayed was the result of a separate clean-up on a considerable quantity of ore. The ore varied widely in grade and in other respects, but the runs bracketed in the table were made at the same time, in adjoining batteries, and on similar types of ore. In a * Result modified by the addition to the bullion-shipment of a little impure bullion left over from previous clean-ups.. On these occasions, the strips of copper were removed from the tables, and: their lower surfaces were cleaned. Hence the higher yield reported.

Jan 1, 1900

By Benjamin C. Craft

As predicted, during 1937 South Louisiana witnessed one of the most active drilling campaigns in the history of the area, resulting in the discovery .of 14 new fields. The economic importance of 10,000-ft. production was far-reaching and the objective depths placed on some wildcats was 12,000 feet. Most of the important discoveries and deep tests were in the delta area between the Atchafalaya and Mississippi Rivers, where the upper Miocene sands were found productive between 10,000 and 11,000 ft. The casing program on these wells usually called for a protection string of 95/8-in. casing at approximately 9500 ft. Drilling barges with the heaviest equipment were used where water transportation was available. The oil production for South Louisiana during 1937 was 62,147,690 bbl., as compared with 51,968,727 bbl. during 1936, an increase of 19.5 per cent. There were 281 oil and gas wells and 172 dry holes completed during 1937 as compared with 262 oil and gas wells and 135 dry holes during the previous period. New Fields Gibson.—The first discovery for the year was in the Gibson area, where Shell Petroleum Corporation's Realty Operators No. 1, sec. 18, 17 S., 15 E., Terrebonne Parish, was completed flowing 780 bbl. of 38° A.P.I. oil daily through a 14/64-in. choke with a tubing pressure of 1700 lb. Production is from upper Miocene sand found from 9461 to 9483 feet. Abbevil1e.—The discovery well for the Abbeville field was Continental Oil Company's Hebert No. 1, sec. 20, 12 S., 3 E., Vermilion Parish, completed flowing 50 bbl. of distillate and 2 million cubic feet of gas through a 3/16-in. choke with a tubing pressure of 2550 lb. The well was plugged back from 12,216 ft. in the Chickisawhay, and is producing through perforations from upper Miocene sand found from 7668 to 7682 ft. Later in the year, the same operators completed Brookshire No. 1, sec. 66, 12 S., 3 E., flowing 366 bbl. of 42° A.P.I. oil per day through a 3/16-in. choke with a tubing pressure of 1800 lb. This well was com-

Jan 1, 1938

By John Hall

SOME months ago one of the authors was asked to write a paper on the heat treatment of steel castings that would be more comprehensive than other matter lie had published; this is an attempt to present in condensed form the results of experimental work and actual practice carried out for the most part in 1907, 1908; and 1909. It is not a laboratory research and the work done was carried out for the express purpose of putting in practice the processes discovered as fast as possible. Most of the tests are the result of commercial practice and not of bars annealed in our laboratory; most of the micrographs were made for our own records and not for publication. Certain of the micrographs, therefore, are not as clear as we may wish but they were good enough for our purpose at the time they were made. The tests and micrographs are selected from several thousands in our files. All of these micrographs are magnified 60 diameters. These experiments were conducted almost entirely on steel made in a 3-ton bottom-blown converter, and most of the steel illustrated analyzes about 0.05 in phosphorus and sulfur. Unfortunately, a certain number of specimens are shown of which we do not have the complete analysis, but in most cases in which the phosphorus and sulfur vary much from the figure just given that fact is noted. For purposes of comparison, we have included a certain number of micrographs and tests of steel made in the electric furnace, some of which were from specimens made in other shops and some in our own shop, and some tests of acid open-hearth and tropenas steel.

Jan 9, 1919

By Fred P. Peters

T. D. Yensen.*—As my information is of a negative nature, I think it belongs under this paper. We are particularly interested in magnetic materials and we would like very much on occasions to make use of powder metallurgy. We have tried repeatedly to use powder metallurgy in preparing our nickel alloys but always. with negative results; that is, we cannot get as good magnetic properties by powder metallurgy as we can by starting with a molten material. We have tried by all possible means to make materials' like 50 per cent iron-nickel alloys by powder metallurgy. The compacts can be regularly lorged and rolled but no matter what we do in the way of annealing, the magnetic properties come out very much poorer than if we start with molten material. F. V. Lenel. †—I want to mention one characteristic of articles made from metal powders which distinguishes them from die castings; that is, their wear resistance. Die castings usually are made from zinc or aluminum alloys and a few copper-zinc alloys; all of them are comparatively soft and not very wear resistant. I know of a number of cases where powder metallurgy rather than the die-casting method was used for producing a certain part because higher wear resistance was needed than could be attained in die castings. A, J. LanghammeR.*—The subject of powder metallurgy is somewhat difficult to discuss, and portray, in the time that his been allotted. Most of you would rightly be bored if we went into details. However, I will cite one incident that possibly will help illustrate some of the potentials. Last summer I was in Washington and met Navy officials for the purpose of studying the possibility of making a certain part by powder metallurgy. The part is highly intricate and I happened to remark that the material cost would be high; that is, the cost on one raw material. Promptly a high-ranking Navy officer said: "Mr. Langhammer, if you must pay x dollars a pound for the raw material, but achieve the desired results, the cost of the finished part would still be low."

Jan 1, 1945

By John Lohrenz

Consider an investor who, knowing future costs and revenues, can choose how rapidly to produce from a given mineral source. If the investor elects to make that choice to maximize present value of future profits, how do policies affect the choice? Various alternative policies are examined. Some, such as higher royalty rates, lead to slower production rates than would otherwise obtain. Clearly, the chosen rates of production are policy-dependent. One is wisely counseled to consider how mineral policies affect the rate of production from given sources when analyzing current and alternative policies.

Jan 1, 1982

By P. Duwez, L. Zwell

L. S. BUSCH—We have had presented two methods of measuring these variations in powder compacts. E. OROWAN—Tn connection with the rolling mill research work carried out at. the Cavendish Laboratory, Cambridge, with the help of the British Iron and Steel Research Association. Dr. E. A. W. Hoff, Mr. J. Los, and myself, have determined coefficients of friction at ex- treme pressures for a number of liquid and solid lubricants, both by direct measurement, and by calculation from measured values of the roll force. The most efficient lubricants at these high pressures (for the small amounts of sliding that, occur in rolling) were camphor and. in particular, borneol (Borneo-camphor). Perhaps such lubricants could be used with advantage in the kind of work described by Dr. Wulff. L. S. BUSCH—1 think Dr. Wulff has in the past mentioned experiments which have been performed in the extrusion and rolling of metals and which led to conclusions which can be applied to the compacting of metal powder. A. SQUIRE*—There have been some recent developments in the field of high pressure lubricants which indicate that boron nitride might be a very desirable material to employ as a die lubricant. At the present time its cost is prohibitive, but as the need arises for the material it will undoubtedly come down in price. The present price is $200. a pound. It is my understanding that one of the reasons for vacuum pressing both in ceramics and metal powders, is to prevent

Jan 1, 1950

By F. L. Clerc

THE lead and zinc region of SW. Missouri is interesting, not only by reason of the value of its output, which ranges in the neighborhood of ten million dollars a year, but even more because of the facilities which it offers for the study of certain forms of ore-deposits, of which the loci and genesis are somewhat obscure. Although the mineral species found in the region are few and of common occurrence, crystallization has taken place on a generous scale, and unusual forms abound in many combinations, presenting examples of pseudomorphism, paragenesis, metasomatic replacement and the action of mineral-depositing and mineral-dissolving waters. For the mineralogist, lithologist, and specialist in certain lines of metamorphism, it has peculiar attractions, while the systematic geologist will perhaps find its chief claim to attention in the simplified problem it presents, in the study of ore-deposits. In addition to the phenomena above enumerated, it presents instances of well-developed comb-structure in the ores, fissures and faults, and slickensides-features usually associated with extensive movements in the earth's crust, and believed by some authorities to prove the deep-seated origin of the ores. In connection with these occurrences, the absence of all igneous rocks from this region is noteworthy and significant. For that reason, the simplified case presented by the Joplin region, from which these rocks have been eliminated as a factor, is specially valuable. Having had unusual opportunities to watch the development of this district, I have been deeply interested in the bearing of the revelations of the Joplin mines upon questions of universal importance to the science of ore-deposits ; and it was to my great regret that the project of a meeting of the American Institute of Mining Engineers at Joplin, proposed in 1892, was

Mar 1, 1907

AALL, Christian H.,(M'49), Asst Res Dir Monsanto Chemical Co Anniston, Ala AALSETH, Earl P ,(J,51), Amerada Petr Corp Geological Dept Williston N Dak AAMOT, Olav Crone, (M'29), Met Pacific N W Alloys, Inc , Box 6215, Hillyard P 0 Spokane 14, Wash AARING, Floyd D ,(J'48), Petr Engr P 0 Box 130, Calgary, Alta Canada AARCNSON, Hubert Irving, (S'47), Carnegie Inst of Tech., Pittsburgh, Pa ABADIE, Henry G ,(M'43), Asst to the Sup- of Operations, Long Beach Oil Development Co ,255 So Santa Clara Ave Long Beach, Calif ABBISS, H. J., (A'50), Min. Engr., Buchans Mining Co., Ltd.. Buchans, Newfoundland ABBOTT, Clarence Eugene, (M'04), 901 Insurance Bldg , Raleigh, N C ABBOTT, George, (S'52), Mass Inst of Tech Cambridge, Mass

Jan 1, 1952

By George B. Langford

ON THE QUESTION of postwar controls there are today three schools of though ; some advocate state control of everything the socialists ; second are those who advocate the removal of all governmental control over industry - the freedom of enterprise ideal ; and third are those who advocate a middle course - sufficient control to stabilize economic and industrial life, and to prevent violent fluctuations such as we saw in the interwar years. I advocate this third course. I firmly believe un free enterprise, but not in freedom of enterprise, or laissez faire, and there is a great and significant difference between these two.

Jan 1, 1944

Jan 1, 1880

By H. B. Menardi

The history, geology, ore deposits and current mining operations of the Huitzuco district have been described by C. W. Vaupelll and the current mill operations by David Segura.2 This paper completes the story of Huitzuco with a description of the reduction of the flotation concentrates. The predominant ore mineral in the Huitzuco deposit is livingstonite, a rare, mercury-antimony sulphide (HgS.2Sb2S3). Other associated minerals include cinnabar, stibnite and elemental sulphur. The gangue is largely limestone and gypsum. Former operators mined a selected grade of ore, from which the mercury was recovered by an expensive, inefficient operation. A considerable tonnage of rejects and fills, carrying mercury and antimony, was left in the mine. In order to recover both mercury and antimony from these fills and also from newly developed ore, a combination method has been developed, by means of which the livingstonite is concentrated by flotation and the flotation concentrates subsequently reduced to metallic mercury and antimony. An essential part of the flotation treatment, as developed by Segura, is the use of copper sulphate as an activating agent. A typical analysis of concentrates now being produced at the property is as follows: Hg, 7.73 per cent; Sb, 26.40; Fe, 1.20; S, 29.68; CaO, 11.50; MgO, 7.25; SiOz, 1.63; A1203, 0.65. PRocess foR Treatment op Concentrates In the development of a process for treatment of these concentrates, three different methods were investigated: (1) roasting in a Dwight-Lloyd sintering machine with an excess of air; (2) separation of mercury and antimony by distillation in a reducing atmosphere; (3) a third method, which ultimately developed into the present process. The third method involved a slow calcination at a closely regulated temperature with a limited admission of air, which separated the mercury and antimony, the raeroury passing out of the kiln with the furnace gases and the antimony remaining in the calcine or "sinter."

Jan 1, 1944