Search Documents

By S. C. Sun, T. Chao

The reaction of gaseous sulfur trioxide with different aluminum-bearing minerals for the conversion of their alumina content into water soluble sulfates has been investigated. Theoretical considerations indicate that this reaction is thermodynamically feasible and that preferential sulfatization can be accomplished. The five minerals tested were gibbsite, boehmite, diaspore, kaolinite, and halloysite. In general, over 90% sulfatization could be achieved in 1 hr when using sodium sulfate as an additive at a temperature between 500° and 600°C. It was found that sulfates of the light alkali and alkaline earth metals exhibited some effectiveness in promoting the sulfa-tizing reaction. Selective sulfatization of alumina in a mixture of calcined halloysite and ferric oxide was accomplished. The gas-solid type of sulfatizing reactions have become increasingly important in recent years for the treatment of the oxides of such nonferrous metals as cobalt,' nickel,' manganese,3 zinc, and copper.4-6 Similar reactions were attempted in the present investigation for the recovery of aluminum from the low grade aluminous ores. Unlike the Bayer process in which silica is a serious contaminant, or the acid processes whereby iron usually causes difficulties, the reactions between gaseous sulfur trioxide and various aluminous minerals could hopefully be selective for aluminum. THEORETICAL CONSIDERATIONS Reactions between aluminum-bearing minerals and gaseous sulfur trioxide have been shown respectively in Table I and Fig. 1 to be thermodynamically favorable for temperatures below 1000°K approximately. Calculations of the thermodynamic functions were where ?G, ?H, ?Cp and ?S are changes in free energy, enthalpy, constant-pressure specific heat, and entropy of the system under consideration, respectively; T is the absolute temperature, R the universal gas constant, and K the equilibrium constant. Thermochemical data so far available for these calculations were based on sources given by T. Chao.7 In Table I, the free energy values indicate that reactions between the gaseous sulfur trioxide and

Jan 1, 1968

By Günter Petzow, Siegfried Steeb

DURING an investigation of the U-Co-A1, U-Ir-A1, and U-Ni-A1 ternary systems, three previously unknown phases have been identified which correspond to the phases UCoA1, UIrA1, and UNiA1, and which be- long to the C22 (Fe2P) type (P 6 2m). In the following the structure determination of the new ternary phases is reported. The alloys have been prepared in an arc furnace under purified argon from 99.97 wt pct U, 99.83 wt pct Co, 99.99 wt pct Al, 99.95 wt pct Ni, and 99.97 wt pct Ir. The pellets obtained were bright and brittle; chemical analyses agreed with the nominal compositions. To obtain equilibrium, the samples were annealed in evacuated quartz capsules at 950°C for 30 hr and then quenched in water. Guinier photographs were processed and evaluated according to a method already described previously.1,2 The hkl's, measured and calculated sin2 6 values, and in the case of UCoAl only calculated and estimated intensities, are given in Tables I to 111. Lattice parameters refined according to the least-squares method and the respective mean-square variations are presented in Table IV. Lattice parameters, especially the c/a ratio, lead to the assumption that the three phases are crystallizing in the C22-type structure. For the calculation of the intensities given in Table I, the atomic positions recently reported by wyckoff3 have been accepted for the C22 (Fe2P) type. The uranium atoms were assumed to be in phosphorus sites; furthermore the scattering amplitudes of the boron atoms have been averaged in the stoichiometric formula UB2 according to atomic percentages; i.e., for these atoms a statistical distribution on the iron sites was assumed. The two smallest distances between a uranium and

Jan 1, 1967

Have your name and address on the first page of your manuscript. Typewritten manuscript is preferred, but is not essential. If you have the manuscript typewritten, have it double spaced and written on one side of the page only; send two copies to us if convenient; only one copy of the illustrations is desired. In typewritten manuscript, formulas are better inserted by hand. Keep a copy of your manuscript in case of loss in the mail. ILLUSTRATIONS.-Photographs reproduce best when printed on glossy paper. Solio is one of the best varieties. A good print is preferable to a negative. Blueprints, drawings, or pen or pencil sketches can be used for line engravings, but care should be exercised to make them legible and clear, especially in the case of blueprints. Tracings or photographs of drawings are preferable to blueprints. Rough sketches can be used, if necessary. Photographs should be sent flat, not rolled. Do not put reference letters or other marks on photographs; if such letters or marks are necessary, fasten a piece of tracing paper to the top edge, trace a rough outline of the picture upon it and then place all letters, etc. on the tracing paper lithe exact position you wish them to appear. Restrict the number of micrographs as much as possible on account of the considerable expense involved. Standard magnifications for non-ferrous metals and alloys are recommended as follows: 10, 25, 50, 75, 100, 150, 250, 500, 750, 1000, 1500. Micrographs should be trimmed to 2 1/4 X 2 1/4 in. (six micrographs to a plate), or, if larger, up to 3 1/2 X 4 in. (two to a plate). The smaller size should be adopted if consistent with adequate representation of the subject. With each micrograph should be attached an explanatory title, together with the actual magnification, etching medium, treatment, etc., indicating what the author intends to show.

Jan 1, 1919

AN extremely successful meeting, under the joint auspices of the Ohio Section and the Iron and Steel Committee, was held at Cleveland on April 19 and 20, about one-half of those in attendance being from the Cleveland district and the other half from a distance. The morning session on April 19, C. K. Leith presiding, was opened by the presentation of the ad-dress of which an excerpt is printed on the opposite page. In the subsequent discussion R. A. Allen pointed out that the meeting had not been called "to blow the lid off the tariff" since that is only one of the many problems connected with the wisest utilization of man-ganese, and it was the purpose of this meeting to con-sider all those interdependent problems. The purpose of the tariff was to develop an adequate domestic sup-ply, and that result had not been accomplished. An-other important problem, linked with the tariff, is the need for assuring, while we are at peace, an adequate war supply of manganese, and at present this country has no such policy. D. F. Hewett said that his 3-months' trip in Europe last summer had impressed him with the fact that England had once been in the position United States now is in, of being the principal world's producer of all the more important minerals and with a declining reserve had gone on a free-trade basis. No one pointed out that, with the exception of tin, the present relative position of England is due more to an increase in pro-duction in other countries, rather than to a decrease of domestic production. J. Sharshall Grasty referred to recent development work-in Virginia where of 30 per cent easily concen-trated manganese ore about 300,000 tons has been blocked out and possible and probable ore amounting to 700,000 tons more is indicated.

Jan 5, 1927

By S. Skowronski

The melting of cathode copper, ususally containing 95.98+ per cent. • Cu, would appear to be a simple matter. Owing to the well known affinity of copper for sulfur, however, so much sulfur is absorbed by the copper during the operation that a long and expensive refining process is required to remove it, and the final product is inferior in purity and lower in electrical conductivity than the original cathode copper. The furnace operation, as now conducted, includes the following stages: 1. Charging the cathodes into the furnace. 2. Melting the cathodes. 3. Oxidizing period—saturating the copper with cuprous sub-oxide and bringing the metal to the condition known as "set copper;'' this is now done by blowing air into the molten bath of metal. 4. Reduction period, otherwise known as "poling," whereby the oxygen previously added is removed by covering the molten bath completely with coke or charcoal and introducing large poles of green wood; this reduces the cuprous sub-oxide, bringing the copper to the "tough pitch" stage ready for casting. 5. Casting Period. Many experiments have been made to obviate the long periods of oxidation and subsequent reduction, with no success. While the copper first cast will be good, as indicated by the set surface of the bars, it is impossible to hold it to the "tough pitch" condition, and long before the whole charge has been poured the copper will become "overpoled," entailing numerous difficulties. Sulfur has always been blamed by the furnace men as the reason why this refining process is necessary, yet the literature on the subject does not sufficiently emphasize how small a proportion of sulfur will ruin copper for practical purposes. The sulfur absorbed by copper during the melting period comes from two sources: (1) the sulfate left on the cathode sheets in the tank houses; (2) the fuel. The percentage of sulfates on the cathodes is variable, and depends on the care taken in washing the cathodes after removing

Jan 1, 1919

By S. R. Elliott

THE Spies mine is located in the eastern half of the northwest quarter of section 24-43-35, near the village of Iron River, Mich., and is operated by The Cleveland-Cliffs Iron Co. Speaking generally, the jasper hanging walls of most of the deposits in the Iron River district dip at a steep angle and are exceedingly strong, standing without caving, even after mining has been continued for years and after large excavations have been made. The ore is fairly hard and tough and contains no slippage faces. It occurs in large masses, which are often egg shape, with the smaller end down, and can be mined in, open stopes without the use of timber. The common system employed in the district is the shrinkage stope, or some modification of it. The Spies system was developed to utilize the advantages of the open-stope method and to avoid the disadvantages of the shrinkage stope. The Spies shaft was sunk to such a depth that the bottom, or third level, was in rock at a short distance below the bottom of the orebody, the shape and extent of which had been previously determined by diamond drilling. This is shown in plan and by the ore contours at the first, second, and third levels in Fig. 1, and in section in Figs. 2 to 7. In order to provide the necessary mills and raises, three parallel crosscuts were driven on 25 ft. centers on the bottom level. Drifts on the second and first levels were driven to the orebody and followed the foot wall in a southerly direction to the end of the ore. In crosscut 3, Fig. 1, raises 30, 40, 50, and 60 were carried up on the foot wall and holed into the second level, and were ultimately carried up and holed into the first level. These foot-wall raises carry the pipes and ladders, provide a means of ventilation, and furnish safe communication to all working places in the stope.

Jan 3, 1922

By N. A. D. Parlee, I. D. Shah

ThIS reports on some work done on the solubility and diffusivity of oxygen in liquid silver. Solubility. Improvements in the measurement of the solubility of oxygen in silver and silver alloys were made because precise data were needed for calculating diffusion coefficients of oxygen in these alloys. The apparatus and the procedure used were similar to those of Parlee and Sacris.' The main improvement was in the temperature-measuring technique. A MV30 mullite protection tube containing a calibrated Pt-Pt, 10 pct Rh thermocouple was inserted in the reaction tube from the top through a vacuum-tight swage-lok fitting. The protection tube was well-immersed in the liquid silver, which was heated by induction. A Leeds and Northrup potentiometer was used in connection with the thermocouple. All runs reported were made at 1 atm. The temperature range investigated varied from 940" to 1200°C. The ternary point in Ag-0 phase diagram2 is at 939°C and 0.32 wt pct O. This point was reinvestigated using the above-described apparatus and was found to be at 939°C and 0.315 wt pct 0. It was determined by observing the sudden evolution of oxygen at this point while the solubility measurements were made. The point was easily reproducible if precautions were taken to keep the liquid silver essentially in equilibrium with oxygen and to lower the temperature very slowly. All of the results of this new solubility investigation are plotted in Fig. 1. They are represented by the "least-squares" line shown in the figure and the following equation for solubility at po2 = 1 atm: log% O =695.4/T - 1.086 This equation differs only slightly from that proposed by Parlee and sacrisl and that of Diaz, Masson, and Richardson.3 The points of Parlee and Sacris, using an optical pyrometer, are shown for comparison.

Jan 1, 1968

By Dale E. Walker

The Captain mine came into being under the following circumstances: 1) Commonwealth Edison had need for fuel for the generation of electricity in their Chicago service area. 2) Southwestern Illinois Coal Corp. had an ample supply of coal in the Illinois No. 6 and No. 5 seams. 3) The Gulf, Mobile & Ohio R.R. had a one-line transportation system with the capability of transporting coal from the Captain mine to Commonwealth Edison. These fortuitous conditions permitted an effective three-way partner- ship to develop. Commonwealth Edison had built a new generating station at Joliet, Ill., across the Illinois River from the existing station, to supplement their power-generating capacity for the Chicago area (Fig. 1). The annual requirement of the Joliet station is approximately 4.5 million tons of coal. From large reserves of coal in the No. 6 and No. 5 seams, Southwestern Illinois Coal Corp. contracted to supply Commonwealth Edison with approximately 6 million tons annually from its Captain mine. The logical carrier was Gulf, Mobile & Ohio, whose mainline travels through this coal field and also passes by the Joliet station on its way to Chicago. This railroad has been moving Southwestern's coal from the Streamline mine for more than 30 years. The basic ingredients of timing, scheduling, moving, and handling were adopted by the three parties, the precise details being worked out jointly. To do this, each group had to know its requirements exactly. The initial schedule was drawn up and tentatively approved, with each party taking a hard look at its own requirements and commitments to make certain that the schedule could be met on a normal daily basis. With only minor changes, the final schedule was adopted, each participant feeling that it had a sufficient factor of safety to maintain steady operation. Each party agreed to help the other in time of emergency. When a delay occurs in any part of the operation, the other

Jan 1, 1969

By Joseph E. Pogue

Price is a complicated concept, for price is both a cause and an effect. This reciprocal aspect is commonly overlooked and the oversight is the source of many economic maladjustments. Price is the resultant of the ratio between supply and demand, but it differs from a mathematical concept of a proportion, by itself constituting an economic force which continuously alters the elements that determine the relationship. Price, therefore, is not merely the outcome of other forces but is in its own right one of the most powerful of economic agents. Price accordingly does not play a passive role; nor can it be sterilized or rendered inactive. In consequence, price cannot be fixed or at least kept fixed, except by the elimination of all freedom of choice on the part of producers and consumers. A primary objective of all economic activity is equilibrium. The same is true of a unit of economic activity, the single industry. The plane upon which equilibrium centers may shift in the course of time, but equilibrium itself is the point of departure and the point of return. If an industry is in equilibrium, that industry is operating effectively. The motivating forces of an industry—profits or the common good—are not to be confused with the prerequisite of equilibrium, but this mistake is often made. The producer is dominated by the profit motive; the consumer, or his collective representative, by the general welfare motive. No one is the advocate for equilibrium; that status is supposed to be arrived at automatically. If the forces of competition are perfectly free, such is the tendency. Equilibrium For the purposes of this analysis, equilibrium needs to be broadly defined and is conceived to involve: (1) balance between supply and demand; (2) internal equipoise amongst the elements within an industry; and (3) symmetry in respect to the whole economy. This definition implies flexibility and case of adjustment; a ready accommodation to change. Equilibrium does not postulate profits or nonprofits, social objectives or the lack of them. A decadent industry may be in equilib-

Jan 1, 1937

By E. P. Mathewson

THE experiments described in this paper were made at the Washoe Reduction Works, Anaconda, Mont., for the purpose of determining the relative speed of elimination of the iron, sulphur and arsenic during the process of bessemerizing copper-mattes. The samples were taken from a horizontal "barrel" converter, 8 ft. in diameter and 12 ft. 6 in. long, having an average charge of 9 tons of matte, and blown with a 16-1b. air-pressure. All samples were taken with the blast on, turning the converter from its normal blowing-position to nearly verti¬cal, so that a conical mold, with a long handle attached to a horizontal rod, could be introduced from a platform above the converter into the mouth of the converter and a sample taken. The difficulties of taking a sample with the blast on are appar¬ent, and the irregularities of the lines in Figs. 1, 2 and 3 can be readily accounted for by the amount of slag in the samples. On the whole, the plotting of the results gives comparatively uniform lines, considering the conditions. The samples were taken by the regular sampling-force of the works at 10-min. intervals, as shown in Tables I., II and III, which also give the chemical analysis of the samples so taken. The test shown in Table I. was made with a new converter; that of Table II with a converter that had made three charges and had been cleaned out; that of Table III with a converter that bad blown one charge to white metal, and had then been " washed " out and used for the test. In plotting these results, it was necessary to take, as a basis, the percentage of copper in the samples. This basis does not exactly represent the true condition, since the volume is constantly decreasing and a certain quantity of copper passes into the slag, but it is as near as can be obtained in practice. Take, for instance, in Table I., the sample No. 5, which shows : Cu, 59.9;

Jan 1, 1907

By A. M. Gaudin, D. W. Fuerstenau

By streaming potential techniques, the zeta potential of quartz has been measured as a function of the concentration of dodecylammonium salts at different pH values. These experiments indicate that adsorption of dodecylammonium ions takes place as individual aminium ions until a certain critical concentration is reached in the double layer, at which point the adsorbed collector ions begin to associate into patches of ions, called hemi-micelles. Because of its effect on the surface potential of quartz, pH controls the adsorption of dodecylammonium ions. The value of cooperating agents and nonionized constituents of flotation systems is discussed. A PREVIOUS investigation' of the role of pH in the flotation of quartz with anionic collectors is here extended to an inquiry of how the cationic collector, dodecylammonium acetate, is adsorbed at the quartz-solution interface. The equilibrium amount of this collector adsorbed by quartz has already been measured as a function of concentration and pH.2,3 The weight of prior evidence has suggested that two mechanisms are involved in the adsorption of this collector by quartz, but with existing adsorption measurements alone it is not possible to determine what the mechanisms are. Gaudin and Bloecher2 postulated that a polymolec-ular adsorption coating begins to form before the first monolayer has been completed. Gaudin and Morrow4 indicated that a similar situation might exist in the film of dodecylammonium ions on hematite. A study of electrokinetic potentials at the quartz-solution interface provides some detail toward a fuller understanding of the adsorption mechanism. Experimental Results The zeta potential at the quartz-solution interface was calculated from streaming potential data measured with the apparatus described in detail in a thesis by Fuerstenau5 and briefly in a paper by Gaudin and Fuerstenau.1 The quartz used in these experiments was a 48/65-mesh fraction prepared in the manner described previously.' Zeta potential of quartz was obtained for various amounts of the amine salt at pH 4, 7, 10, 11. In

Jan 1, 1956

By P. de Vitry, Oliver Bowles

THE conventional wire saw, introduced in the slate district of Pennsylvania by the Bureau of Mines in 1927, and used thereafter with remarkable success, consists of a three-strand steel cable having a diameter of 3/1 6 or 1/4 in. The equipment, methods used, and accomplishments have been described in previous reports.1-7 Similar wire saws have been used extensively in Europe, in quarries and in shaping blocks and slabs. During the period 1932-1937, competition in European marble quarries was keen, prices were declining, and orders were not abundant. When orders were received, there was generally an urgent call for speedy delivery. Because of the diversification of demands, it was impossible. to maintain in stock marbles of the color, size, and thickness called for,, therefore the material generally had to be fabricated after the order was received. The wire saw enabled stone mills to fill. such, orders promptly. With skillful handling, 7/8-in. slabs could be cut accurately and rapidly with this equipment. It was found, however, that, as the three-strand wire became worn, the cutting speed dropped rapidly and the cut became less accurate. To overcome these difficulties the junior author of this paper, after much experimentation, developed a new type of wire consisting of a single ribbon-shaped strand, twisted as shown in Fig. I. To ensure straight sawing, the twist of the ribbon is reversed from right to left and vice versa every 25 ft. The reversal of the [ ] twist is shown in Fig. 2. This is not a new feature; it has been used to advantage with the three-strand wire both in Europe and America for several years. However, some difficulties arise in splicing the three-strand reverse-twist wire, and the claim is made that cutting is less accurate as the wire becomes worn. To make an endless belt, the ends of the single-strand wire are brazed together with

Jan 1, 1941

By Dale Nix

DuRing the past year approximately 400 depth pressures have been recorded in the Yates field. Of these, 315 were "shut-in depth pressures," observed for the purpose of adjusting well potentials without making open-flow tests. The "shut-in depth pressures" were distributed one to each well and determined under as nearly uniform conditions as possible. Therefore, there is a scarcity of data applicable to production problems, other than the adjusting of well potentials. A few of the data obtained have been used in an attempt to solve some of the producing problems. These applications, however, merely indicate partial solutions and their review herein is to emphasize the variety of problems to which depth-pressure data can be applied, rather than to present conclusive solutions. Very little had been accomplished in the development of instruments to determine pressures within the well bore, when it was decided to obtain such information in the Yates field. Through the combined efforts of the Yates Engineering Committee and several producing companies, three methods of determining pressures in the well bore were soon developed: (1) the "compressor" method, (2) the "volume chamber" method, (3) the "depth-pressure recorder" method. "Compressor" Method.—A small volume compressor is used to inject gas into the tubing. The rate of injection is low so that the frictional losses will be reduced to a minimum. During the test, the pressures at the top of the tubing and casing are observed on recording pressure gages. .As the compressed gas depresses the fluid in the tubing, the pressure on the casing decreases while the tubing pressure increases. The tubing pressure becomes a maximum when the fluid level reaches the bottom of the tubing; and the casing pressure usually rises quickly as the gas breaks around the bottom of the tubing. The sum of the maximum pressure recorded at the top of the tubing and the pressure exerted by the weight of the compressed gas column is equal to the depth pressure at the bottom of the tubing. The procedure can be reversed;

Jan 1, 1932

By S. S. Lau

The authors of the previous comment stated that Dorn and Rajnak33 and others34-40 concluded that "agreement with this function [(t'/tp) -f(Un/2Un) = T/Tc} may be used as a criterion for that (the Peierls) mechanism of deformation". In contrast, however, Dorn and Rajnak33 and others34-40 never made such a statement. In order to clarify the issues involved it is appropriate to recapitulate the conditions that must be satisfied in order to suggest that some deformation process might obey the Peierls mechanism: 1) Within permissible variations due to changes in the slope of the Peierls hill the T*/Tp - T/Tc relationship must be obeyed. Although some mechanisms, e.g.. solute atom stress field, recombination of dissociated partials in bcc metals, intersection of dissociated dislocations, and so forth, give about the same t* - T relationship, other mechanisms, such as cross slip, disruption of attractive junctions, climb, motion of jogged screw dislocations, and so forth, give distinctly different t*-T relationships. On this basis some distinction can be made of the various mechanisms. 2) An important feature of the Peierls mechanism concerns its physical origin based on the nucleation of pairs of kinks. The value of T* at 0°K increases with the density of dislocation (i.e. , cold work) for the intersection mechanism and it increases with the square root of the atomic fraction of solute atoms in the solute atom interaction mechanism. In contrast the value of t* at 0°k, for the Peierls mechanism which depends only on the line energy and the shape of the Peierls hills. is independent of cold working and the square root of the solute atom concentration. These differences have been employed by various investigators for elimination of a few other possible mechanisms. On the other hand it is not possible to eliminate all mechanisms, e.g., the recombination of dissociated dislocations in bcc metals, and so forth, on this basis alone. 3) Further discrimination between possible mechanisms is based on the activation volume. For the in-

Jan 1, 1968

By Gerhard Derge, Harold Markus

The introductory paper1 of this series described the potential behavior of tin in sodium carbonate and bicarbonate solutions whose pH ranged from 8.4 to 11.2 and demonstrated that significant and reproducible results could be obtained by proper attention to experimental technique. In examining the corrosion of tin under such conditions, it is desirable to know the effects of anions, aside from carbonate, that are likely to be present in commercial materials packaged in tin. Therefore, in this paper the potential behavior of tin in carbonate solutions to which sodium fluoride, chloride, bromide, iodide, sulphate, nitrate, monobasic phos-phate, dichromate, perborate and acetate have been added will be dcscribed. For most of the additions, solutions containing 0.001 and 0.01 moles of the added material were studied. The experimental procedure was exactly the same as that described in the first paper; the pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicar-l,ol~ate as follows: pH 0.1 M NaHC0............................................ 8.4 2 parts 0.1 M XaHCOr, 1 pa.rt 0.1 M NaZCO?................. 9.5 1 part 0.1 M NaHCOs, 2 parts 0.1 M iVa.,C03. ................ 10.0 0.1 M Na2C0............................................. 11.2 The reagents used were all of C.P. grade. The anions studied may be divided into three groups: (1) anions that had little or no effect upon the potential curves—sulphnte, nitrate, and acetate; (2) those that helped to prevent corrosion at low pH only -fuoridc, chloride, bromide, and iodide; (3) those that helped to prevent corrosion at high pH also—phosphate, pcrborate, and chromate. Potential Measurements f The time-potential curves represntative of group 1 are shown in Fig. 1. These are the curves for 0.005 M sulphate ion and their similarity

Jan 1, 1939

By Harold Markus, Gerhard Derge

The introductory paper1 of this series described the potential behavior of tin in sodium carbonate and bicarbonate solutions whose pH ranged from 8.4 to 11.2 and demonstrated that significant and reproducible results could be obtained by proper attention to experimental technique. In examining the corrosion of tin under such conditions, it is desirable to know the effects of anions, aside from carbonate, that are likely to be present in commercial materials packaged in tin. Therefore, in this paper the potential behavior of tin in carbonate solutions to which sodium fluoride, chloride, bromide, iodide, sulphate, nitrate, monobasic phos-phate, dichromate, perborate and acetate have been added will be dcscribed. For most of the additions, solutions containing 0.001 and 0.01 moles of the added material were studied. The experimental procedure was exactly the same as that described in the first paper; the pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicar-l,ol~ate as follows: pH 0.1 M NaHC0............................................ 8.4 2 parts 0.1 M XaHCOr, 1 pa.rt 0.1 M NaZCO?................. 9.5 1 part 0.1 M NaHCOs, 2 parts 0.1 M iVa.,C03. ................ 10.0 0.1 M Na2C0............................................. 11.2 The reagents used were all of C.P. grade. The anions studied may be divided into three groups: (1) anions that had little or no effect upon the potential curves—sulphnte, nitrate, and acetate; (2) those that helped to prevent corrosion at low pH only -fuoridc, chloride, bromide, and iodide; (3) those that helped to prevent corrosion at high pH also—phosphate, pcrborate, and chromate. Potential Measurements f The time-potential curves represntative of group 1 are shown in Fig. 1. These are the curves for 0.005 M sulphate ion and their similarity

Jan 1, 1939

By A. S. Nowick, A. E. Roswell

Anelastic measurements of atomic mobility in an Ag-Zn substitutional solid solution, make possible a study of the rate of decay of lattice defects frozen into the alloy by quenching. A WIDE variety of experimental evidence has accumulated recently in support of the belief that atomic mobility or diffusion in face-centered cubic lattices occurs principally through the movement of lattice defects, as contrasted to a mechanism by which two or more atoms directly exchange lattice positions. The most direct evidence, summarized in a recent review,' includes the Kirkendall-effect measurements and anelastic measurements on quenched alloys. Theoretical calculations' have focused attention on the lattice vacancy as the defect probably responsible for diffusion in the common metals. Later calculations3 have also shown the possible importance of combined pairs of vacancies in producing diffusion. The only defect that has been considered seriously, in addition to the vacancy and combination of vacancies, is the "interstitialcy" (an atom which has left its normal lattice position and entered an interstitial position) ; the calculated energy of formation of an interstitialcy in a close-packed lattice is too large to permit a reasonable probability for the occurrence of this defect In view of these calculations it may be tentatively concluded that the defects producing atomic movements are single or multiple vacancies. Anelastic measurements of atomic mobility in substitutional solid solutions provide a valuable method for the study of lattice defects. By means of this method it was first demonstrated' that defects may be frozen into a lattice by rapid quenching from high temperatures. (It was subsequently shown6 that resistivity measurements may also be capable of detecting the presence of frozen-in defects.) A summary of the principles involved in these anelastic measurements will now be presented. The anelastic method is based on a relaxation phenomenon in substitutional solid solutions, first discovered by Zenera in a brass and subseauentlv investigated extensively in a series of Ag-zn solid solutions.' This relaxation effect may be observed in the usual way either dynamically, as a peak in

Jan 1, 1954

By H. R. Shidel

This paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. 8. Bureau of Mines; Magnolia Petroleum -Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," 5. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon, (2) That the only striking connection between structure and water is in .the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by finegrained, well cemented sand, which is barren. Possibly two or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 1, 1920

By E. M. Murphy

Eight years ago the Hecla mine, a lead-silver producer, situated at Burke, Idaho, was producing ore from but two levels, the 300- and the 600-ft. All hoisting was done with a 12- by 16-in. slide-valve, double-reel, hoist. The hoist was being worked to its capacity and was unsuitable for hoisting from greater depths. As the work of opening a new level was about to be started, it became necessary to remodel the then-existing equipment or install a new hoist. The recent advent of electricity from Spokane had made available a cheaper power than steam. By a series of tests conducted throughout the Cæaur d'A1ene district, it was found that it cost $109 per year to generate a horse-power with steam. Electric power was to be had for $50 a horse-power per year. It was decided to substitute for the engines a motor-drive, of sufficient capacity to operate from the 900-ft. level, and ultimately install an entirely new hoist. After disconnecting the engines, installing a new shaft, and making a few minor changes, a 300-h-p., 2,300-volt, 514-rev. per min., variable-speed motor of the induction type was geared to the reel-shaft. The reels were supplied with 3/8- by 4-in. flat rope, and the duty of the hoist was about as follows: Cage, 1,700; ore, 2,600; car, 1,400; rope, 2,250; total, 7,950 pounds. The Bristol ammeter chart, Fig. 1, shows the combined current-consumption of the hoist- and mine-motors. The large intermittent load is clearly shown; this produced harmful fluctuations in the voltage of the long, lightly-loaded, 60,000-volt transmission-line from Spokane to the Cæmur d'A1enes. The power company received no compensation for the increased cost of producing power for this intermittent or fluctuating load. In order to protect its system from similar excessive

Jan 1, 1913

By J. A. Elias, R. H. Heyer, J. H. Smith

Plastic anisotropy determined by the ratio of width strain to thickness strain in tensile specimens of low-carbon steels is strongly related to crystallographic preferred orientation. Using(222) Pole figures, a method was developed which permits rapid Predictions of plastic anisotropy for any crystallographic texture or orientation. The method is applied to low-carbon steel sheets in which four different crystallographic orientations were produced by variations in cold rolling and annealing treatments. AnISOTROPIC behavior of metal sheets during plastic deformation has long been evident. A familiar example is earing in cup type draws. During tension testing of sheet specimens, anisotropy results in a difference in width strain as compared with thickness strain. Carpenter and Elam1 observed this phenomenon in single crystals of aluminum for both sheet and rod samples. Lankford, Snyder, and Bauscher2 made tension tests on sheet samples of aluminum-killed low-carbon steel to determine the ratio of the width-to-thickness strains, and showed that this ratio was related to drawing performance. Burns and Heyer3 calculated theoretical ratios of width strain to thickness strain for two specific orientations of the bee system, using <111> as the operative slip direction. These calculated values were in fairly good agreement with the ratios determined by tension tests of low-carbon steel sheets in which these preferred orientations existed. The high degree of plastic anisotropy of silicon steel sheets could also be predicted from their crystallographic structure by these calculations. The present study has been made to show that the anisotropy observed in plastic tensile straining is strongly orientation dependent and can be adequately predicted for many orientations and textures. PLASTIC STRAIN RATIO R In the region of uniform elongation of a tension test specimen the plastic deformation may proceed at different rates in the width and thickness directions. Such anisotropy has been described in the past by the plastic strain ratioR:

Jan 1, 1962