Search Documents

By J. E. Powers, T. D. Taylor, N. E. Wood

A computer program has been developed to simulate a gas transmission 1ine operating under transient conditions. The program was developed by application of the basic mass and momentum balance equations. The nonlinear equations thus obtained were transformed by the method of characteristics and finite-difference techniques to make them suitable for machine computation. Three tests of the computer program were made. In each of these, the initial condition was assumed to be steady-state flow, the inlet density was held constant at the initial condition, and the outlet mass flow rate was varied with time. One test was theoretical in nature, but the others were made for direct comparison with actual field data. Results of the tests are presented in graphical form. INTRODUCTION Theoretical investigations of the transient flow of gas in long pipelines have been limited in number. In 1951, Olds and Sage4 developed a gaphical method of solving the nonlinear flow equations describing transient gas flow in a long pipeline. Research in this field at the U. of Oklahoma was initiated by Nelson1 in 1956. Nelson utilized a computer to solve numerical equations involving a lengthy trial-and-error procedure, and his results have been reported in the literature? It does not seem likely that Nelson's method can be extended to the analysis of transient behavior of pipeline networks; therefore, the investigation to be discussed in this paper was undertaken to improve and extend the previous work. The following discussion presents, briefly: (1) the basic differential equations governing transient flow, (2) transformation of these equations into a form suitable for machine computation. (3) role of boundary conditions in the calculations, (4) a very brief description of the computer program which was developed to simulate the pipeline and (5) results of tests of the computer program.

By P. J. Jorgensen, J. H. Westbrook

The anomalous indentation creep of nonmetallic solids is shown to be due to the presence of adsorbed water. Although a specific mechanism is not proposed, it is suggested that the water may be present in two chemically adsorbed states. DEPENDENCE of the indentation hardness of solids on the time of load application was first studied systematically by Hargreaves1 in a study of lead and certain low-melting alloys. This technique has become known as indentation creep and has been exploited particularly by underwood and by Mulhearn and Tabor3 as well as by others.4°7 For metals good correlations have been found between the time dependence of hardness over several orders of magnitude in the seconds range and creep parameters from conventional tests at the same temperature where creep strains were measured over hundreds or thousands of hours. However, Walker and Demer8 and Mitsche and Onitsch9 observed extensive indentation creep at room temperature (particularly for light loads) in certain minerals and in materials such as lithium fluoride and magnesium oxide for which conventional creep is ordinarily not observable unless the testing temperature is at a very much higher fraction of the melting point. Normal behavior was observed' for metals such as copper, i.e., negligible time-dependent flow during room-temperature indentation. Walker and Demer attempted to find some distinctive difference in the surface deformation markings about indentations in the anomalously behaving materials at short and very long indentation times. No significant differences were observed. Increased duration of loading was found, however, to result in an increase in the length of glide of edge-dislocation loops extending into the interior of the crystal. Jorgensen and Westbrook,10 in a recent study of

Jan 1, 1965

By J. A. Bartnik, Gerald D. Rose, William H. Benson

New techniques in the magnetite and heavy media beneficiation industries demand more efficient magnetic dispersion and flocculation of the finely ground particles. Demagnetizing coils must produce several major effects, such as improving classification and screening efficiency, decreasing moisture content in filter cake and improving separation selectivity and green pellet properties. Likewise, magnetic flocculators must increase filtering rates and the settling rates of solids, improve magnetite recovery and produce cleaner water. To improve the design of equipment and to conduct tests leading to the optimization of such dispersion and flocculation, a program was initiated at Eriez Magnetics. The major conclusions reached are: 1. Laboratory and plant scale tests conducted on magnetite products show that a demagnetizing force of 450 rms oersteds at 60 cycles for 1/20- second duration will depolarize natural magnetite particles coarser than approximately 10 microns. This has been found satisfactory for most applications. 2. Effective flocculation of magnetite was obtained when a slurry with more than one percent magnetite was exposed for a period of approximately 1/15 second to a 600-gauss field. 3. The cost of demagnetizers (or flocculators) increases rapidly for larger diameter pipes. In order to reduce the cost, narrow rectangular sections are recommended for magnetic flocculators. 4. For minimum operating cost, permanent magnetic flocculators are ideal, chiefly because they do not require any maintenance and have no operating cost. 5. A newly designed electro-demagnetizing coil with high heat dissipation and a nonmetallic core provides high efficiency and long life. 6. To select the correct magnetic flocculator (or demagnetizing coil) the following information is necessary: a. Magnetic product susceptibility b. Magnetic product coercive force c. Percent of magnetic product d. Flow rate e. Viscosity f. Structure of magnetic product

Jan 8, 1968

By F. Weinberg

INTEREST is currently being directed toward grain boundary morphologies in zinc in terms of grain boundary facetingl and grain boundary energies.' Some years ago the present author attempted to measure grain boundary energies in 99.999 pct purity Zn as a function of boundary angle, using the standard procedure of measuring equilibrium angles of the boundary traces at triple points. This followed an investigation he carried out on preferential melting of |H (112) Fig. 1—Electron transmission micrograph of a stacking fault, grain boundary intersection in copper. GRAIN BOUNDARY STACKING FAULT Fig. 2—Schematic representation of the intersection of Fig. 1, indicating inclination angles 0 and trace angles $. specimens were prepared by the Bollman technique in an electrolyte of 70 pct methanol, 30 pct HNO3 main-tained at -30°C. The interfacial free energy of the high angle grain boundary and of the stacking fault is assumed to be thermodynamically equivalent to the corresponding in-terfacial tensions. In terms of the true dihedral angles & between the intersecting interfaces, the equilibrium of interfacial tensions in the direction parallel to the stacking fault yields: ysF = -ygb(cos F1+ cos ±cosF2) Here, ysF is the stacking fault free energy and ygb is the grain boundary free energy, assumed equal on both sides of the intersection. Forces acting normal to the grain boundary, of the form ??gb/?F,l are assumed negligible as the grain boundary remains straight for a considerable distance on either side of the intersection. The micrograph of Fig. 1 may actually consist of several closely spaced stacking faults on the same slip plane. The actual point of intersection between the grain boundary and the first stacking fault, and the equilibrium configuration of the intersection, should not be affected by the presence of the other faults, as

Jan 1, 1970

By Paul R. Cook

The ore deposit of the Buckhorn Mines Co., Buckhorn, Nev., is peculiar in being a shallow kaolinized mass of material with basalt walls, and having apparently no direct connection with any of the usual gold-bearing rocks. The average ore contains 16 per cent. water of hydration, and the cyaniding of this hydrous clayey material offered unusual difficulties as compared with an average Nevada quartz ore. The orebody was thoroughly developed; then the mill was built according to the latest cyanide practice, with such changes as were thought to be demanded by the peculiar nature of this ore. Upon starting the mill, the ore proved more difficult to handle than had been anticipated. It is hoped that an account of how these difficulties were met may prove of interest to anyone having a clayey ore to handle and to the profession in general. Geology The Buckhorn orebody lies along a north and south fault plane of perhaps 1,000 ft. dislocation, that can be traced for miles; but the only other known mineralization consists of similar ore in the Murphy mine, a mile farther north. The east or hanging wall is hard and smooth, being a typical fault plane. The best ore is along this wall, gradually grading down toward the west until at 30 to 60 ft. it is too low-grade to mine. The country rock on the west consists of alternating layers of hard and soft basalt and basalt scoria, pitching toward the mine. One of these basalt layers on the hillside a little above the mine is marked, for 3 or 4 miles in length, by a line of springs which seep out along it. Perhaps the meeting of the surface drainage, passing down these basalt layers, with the fault-plane solutions explains the formation of the Buckhorn orebody.

Jan 1, 1917

By R. H. Sweetser

At the Buffalo meeting in October, 1898 (Trans., xxviii., 865), our Secretary, Dr. Raymond, in speaking of the obstacles he had encountered in securing contributions to the Transactions from members in practice, said : " It is the disinclination of many members to communicate incomplete or partial or preliminary results. They are going to write, ' some day,' a thorough and monumental paper; and meanwhile they prefer to communicate nothing.... It is the difficulty to which I have just referred that I have encountered in a wide correspondence with members, undertaken for the purpose of securing contributions of fact and opinion concerning the special subject of this discussion.... Almost none of them seem to recognize the value of preliminary, incomplete and indecisive reports of practice, as laying the foundation for a thorough' inquiry." This remark was made in immediate reference to a discussion concerning blast-furnace tuyeres; but, notwithstanding this appeal from the Secretary, little has been recorded regarding the distribution, the penetration, and the pressure of the blast at the tuyeres and inside the iron blast-furnace. I am therefore encouraged to contribute the following incomplete and crude observations of the blast-pressure inside the hearth. At the suggestion of J. H. Frantz, the general manager of the Columbus Iron & Steel Go., a test was made at the East furnace of the company to determine whether there was any difference in blast-pressure at the different tuyeres. The apparatus used for this test was not sensitive enough to give accurate results. It consisted of a small pressure-gauge mounted on a 3/8-in. gas-pipe. A hollow plug, fitting into the peep-hole of the tuyere-cap, prevented the blast from blowing-out during the test. The test-pipe was held in place by means of the handle on the outer end.

Jan 1, 1910

By T. B. Counselman

THE importance of concentration of iron ores too low in grade to be smelted direct is shown by Table I, showing 1940 ship- [ ] ments from the Lake Superior district. Canadian ores are omitted. [ ] Only in Minnesota is concentrating, other than crushing and screening, practiced at present. Tonnage produced by various methods of concentration is shown in Table 2. The curves in Fig. I show the gradual increase in tonnage of concentrated ores shipped, compared with total shipments from Minnesota. Most of the concentration work is performed on the Mesabi Range. This range is about 100 miles long, and not over 3 miles wide from the line at which the formation tapers out to a feather edge on the north to the place on the south at which, some 600 ft. thick, it is overlain with slates. CLASSES OF ORE The Mesabi Range contains three classes of iron ore. First is the unaltered taconite, or banded iron-bearing chert. It is estimated that there are some 60 billion tons of this material, which contains, roughly, 25 to 30 per cent iron. This material is virtually untouched, since no commercially successful method has yet been found for concentrating it to a grade suitable for the blast furnace. Intensive experimental work is in progress, and the problem is gradually being solved. In 1922 the Mesabi Iron Co. spent several million dollars erecting a large-scale pilot plant for concentrating and sintering the magnetic taconites on the east end of the range. An important tonnage of high-grade sinter was shipped to lower lake furnaces, proving that the taconite can be concentrated to a satisfactory grade. The costs, with equipment and methods then in use, were too high for

Jan 1, 1941

By H. Landsberg

MANY of the sedimentary rocks contain small amounts of radioactive constituents. These vary in quantity in different layers. Some recent deposits show rather high activity as; for example, the deep sea oozes and some lake deposits.1,2. Measurements made in boreholes have also shown considerable changes in activity from horizon to horizon. The first to publish data on this fact was Ambronn,3 and recently Russian geophysicists have shown remarkable variations of activity from one layer to the next in various wells. Spak4 felt even that he was able to line up horizons from data measured in two neighboring wells. ? The measuring of radioactive radiation is fairly difficult. Large errors are possible by the circulation of gaseous emanations in the well and porous strata. It is, therefore, never certain whether the activity of the layer where the instrumental device or collector is located will be measured, or that of some adjacent layer, For this reason it seemed to be advantageous to take samples of rocks into the laboratory and test them therefor their contents of radioactive material, Such a method has been followed in the past to distinguish radioactive ore from other rocks. Radioactivity of rocks, especially of the igneous type, was also deter-mined in the laboratory by numerous authors for absolute age investi-gations.6 Corresponding data from studies of sedimentary formations are scarce. Specimens taken from a core of the Bradford oil sandstone were tested by Landsberg and Ingham,7 with the results illustrated in Fig. 1, which shows that within relatively small vertical distances the differences of relative activity were considerable. If one assumes that the distribution of radioactive material is fairly uniform throughout a layer, measurements of radioactive radiation in various horizons would offer additional information for stratigraphic

Jan 1, 1939

By Peter Nalle

12.3-1. Reporting. NEED. It seems almost unnecessary to comment on the need for reporting research and development results and activities, and yet much of the difficulty and misunderstanding surrounding a Research and Development (R&D) group results from poor or nonexistent reporting. Certainly no evaluation can be made without reports of results or plans. It is as important to report accurately and fully for the department's own use as it is for external use. Research unreported might as well be considered research undone. This section will discuss, in part, the need for reporting, the general types of reports which may be generated to satisfy the need, and finally, the evaluation of a project as judged by various commonly used standards. PURPOSE. Some specific observations might be appropriate concerning the reporting of R&D results. The requirements and background of the group receiving the report must be considered. A particular report is usually directed towards the background of a particular group, such as ((technical," "operational," "financial," or "marketing." It is essential that the emphasis and coverage be geared to the training of people receiving the report. It should be obvious that the financial department will be less interested in the technical details of the process and more interested in the capital funds and tax implications involved in the project. Operating personnel will be greatly interested in the effects of a new method on mining plans, and so on. This does not mean that the reporting in any way should slight pertinent details, nor should a patronizing attitude be assumed by the writer. However, it is essential that the needs of the reader be recognized. For reports that might have large and varied distribution, it is often feasible to group, either as sections or appendixes, the special details and information of interest only to certain functions within the organization. A

Jan 1, 1968

mean to say that these explosions are mechanical, but that the ejectment of the stock, throwing out of tops, etc., are mechanical. I see no reason at present, although I have had almost no experience in the use of large quantities of Mesabi ore, to change my ideas on the subject. That these explosions should follow irregular working or slipping in the furnace, I think can be explained. I have noticed that immediately following slips there is little or no settling of the stock on top, although there is no lessening of the volume of gas passing into the stoves and boilers. Supposing that, after a slip of 3 or 4 feet, the filling continues, but for some distance from the 'top the stock fails to move: there would be a much better chance for the deposited carbon to clog interstices in the stock, and for the additional effect in the same direction of the fine ore in the charge, than if the stock were properly settling. Under such conditions it is easily supposable that the openings would be entirely closed, or closed so tightly that the pressure below the obstruction would be raised to a point approaching the blast-pressure, or to a point high enough to force a passage or an enlargement of the small passages which may remain. When this occurs, gas from below under pressure carries with it large quantities of deposited carbon and fine ore; if the case is aggravated, coke, stone, bell, etc. As soon as the red-hot deposited carbon meets the air there are perfect conditions for a dust explosion, which naturally follows, the same as in a coal-mine or flour-mill.

Jan 1, 1899

At the end of June, 1938, a new oil field was opened in Egypt, the Ras Gharib. Five wells were completed during the year and gave a total production of 512,988 barrels.' In the Hurghada field production was as follows: Hurghada Field Age of field to end of 1938, years..................... 25 Producing area for gas and oil, acres................ 1,050 Barrels1 Total oil production to end of 1938............... 31,207,754 Total oil production during 1937................ 1,141,356 Total oil production during 1938.................. 1,019,520 Average oil production per acre to end of 1938... 29,719 Average oil production per acre-foot to end of 1938. . . 243.6 Daily average: production in December 1938.......... 2,603.54 Daily average production per well in December 1938. . 34.90 Millions Cu. Ft. Total gas production (Aug. 1925 to end of 1938)... 4,356.7 Total gas production during 1937.................. 222.5 Total gas production during 1938....... . 167.6 Maximum gas daily average of 1938 (ill May 1..... 0.6 Wells Number of producing wells completed to end of 1938 . . 100 Number of producing wells completed during 1938..... 3 Number of wells abandoned during 1938.............. 2 Producing wells at end of 1938 (all pumping)......... 78 Abandoned wells at end of 1938...................... 22 Dry wells at end of 1938......................... 21 Feet Average depth of bottom of producing horizon........ 1,720 Average depth of top of producing horizonlt 1,598 Character of oil, approximate average ill 1938: specific gravity at 60" F'., 0.900; base, mixed. Character of gas, approximate average for 1938: gallons gasoline per 1000 cu. ft. of gas, 6.4. Main producing formation: Nubian sandstone, Cretaceous (PI; sand rock and sandstone.

Jan 1, 1939

At the end of June, 1938, a new oil field was opened in Egypt, the Ras Gharib. Five wells were completed during the year and gave a total production of 512,988 barrels.' In the Hurghada field production was as follows: Hurghada Field Age of field to end of 1938, years..................... 25 Producing area for gas and oil, acres................ 1,050 Barrels1 Total oil production to end of 1938............... 31,207,754 Total oil production during 1937................ 1,141,356 Total oil production during 1938.................. 1,019,520 Average oil production per acre to end of 1938... 29,719 Average oil production per acre-foot to end of 1938. . . 243.6 Daily average: production in December 1938.......... 2,603.54 Daily average production per well in December 1938. . 34.90 Millions Cu. Ft. Total gas production (Aug. 1925 to end of 1938)... 4,356.7 Total gas production during 1937.................. 222.5 Total gas production during 1938....... . 167.6 Maximum gas daily average of 1938 (ill May 1..... 0.6 Wells Number of producing wells completed to end of 1938 . . 100 Number of producing wells completed during 1938..... 3 Number of wells abandoned during 1938.............. 2 Producing wells at end of 1938 (all pumping)......... 78 Abandoned wells at end of 1938...................... 22 Dry wells at end of 1938......................... 21 Feet Average depth of bottom of producing horizon........ 1,720 Average depth of top of producing horizonlt 1,598 Character of oil, approximate average ill 1938: specific gravity at 60" F'., 0.900; base, mixed. Character of gas, approximate average for 1938: gallons gasoline per 1000 cu. ft. of gas, 6.4. Main producing formation: Nubian sandstone, Cretaceous (PI; sand rock and sandstone.

Jan 1, 1939

By I. G. Grettum, Eugene A. Stephenson

The flooding process was originally the result of accidents to casing and tubing, but it has gradually passed from an accidental condition to a definite engineering procedure. In spite of the general sheetlike char-acter of the major sand body, the position of shale bands, their thickness, the size of the grain and variations in effective porosity all give the sand different characteristics in different layers and in different places in the same layer. This condition has an important influence on the movement of flood oil and water, and on the yield per acre, as well as a bearing on what shall be considered the best method of handling flood wells. . A valuation takes into consideration six factors: (1) Flooding methods, of which four have been in common use, as follows, in order of effective recovery, (a) circular flood, (b) line flood, (c) five-spot and (d) five-spot with delayed drilling; (2) recovery per acre, which is definitely related to the oil content, the porosity, the method of flooding, the spacing program, and the continuity of the water supply; (3) the rate of production per well per day, which is definitely related to the mcthod of flooding, the oil content and the porosity of the sands; (4) the operating cost of the well, including royalty, overhead, taxes, etc. (Operating costs are usually expressed as unit cost per barrel.); (5) the expected price per barrel. It is safer to use the average price over a number of years than to attempt to forecast future price fluctuations. The discount factor (the sixth factor) used in appraisal of Bradford flood properties should be less than that commonly applied to other properties, because the hazards of operations have been reduced almost to those of a manufacturing industry.

Jan 1, 1930

By Peter Hood

Data on worldwide geophysical activity in mining exploration programs is collected annually by the Geophysical Activity Committee of the Society of Exploration Geophysicists as part of a continuing service to the industry. The data is obtained by sending out questionnaires to all organizations (which are) known to be carrying out mining geophysical work; the organizations canvassed include mining companies, contractors, government departments and universities. The questionnaire is divided into three sections, namely ground methods, airborne methods and research. In 1968, 515 questionnaires were circulated throughout the non-Communist world and 283 replies were received which is a 55% return. A 67% return was received from the U. S. organizations surveyed so the statistics quoted in this report for the United States are reasonably reliable. This report is published in condensed form, but with emphasis on the United States statistics, with the permission of the Society of Exploration Geophysicists. It was presented at the 39th Annual International Meeting of the SEG in Calgary, Alberta, on September 15, 1969. Worldwide utilization of mining geophysical methods reached a new high in 1968 with total expenditures of United States $41.4 million, compared lo $32.3 million in 1967, representing a 28%, increase. The expenditure distribution by area and type of activity is shown in the graph on page 64. In terms of money spent, ground geophysical surveys accounted for 49% of the total, airborne survey's 36% and research 15%. The percentage of the money spent on ground geophysical surveys fell by approximately 7% from 1967, that for airborne surveys, increased by 5%, and for research the amount increased by 2%. Industry accounted for 79°1% of the total monies spent on mining geophysical activity in the world in 1968 and governments and universities 21 o%.

Jan 1, 1970

By J. T. Norton, J. G. McMullin

E. R. JETTE*—The way this ternary was developed there are two directly determined points on each of the iso-thermals except the 700° isothermal, where I believe there is only one. How were the end points determined, and what was the basis for it? Whose work formed the basis for the silver copper line ? M. B. BEVER †—At most temperatures the authors determined three points of the isothermal line. For example it can be seen from Fig 3 and 4 how three points for the 600°C contour line were obtained. The authors took two additional points for each temperature from the copper-silver binary diagram contained in Hansen's volume on constitution diagrams. It is correct that the 700°C contour line is based only on one point in the ternary field which was found by a slight extrapolation of Fig 4. R. I. JAFFEE*—Are the tie lines representing phases in equilibrium parallel to the silver-copper boundary ? M. B. BEVER—Are you asking that as a matter of principle ? R. I. JAFFEE—I assumed that would follow from principle. I wonder if that is in accordance with the authors' ideas too. M. B. BEVER—I do not believe the authors obtained any information on the tie lines in the two-phase field. Of course, in the limiting case of very low gold contents the tie-lines approach to the silver-copper boundary, but generally in the two-phase field I do not think that the tie-lines have to be parallel to the boundary. E. R. JETTE—I am quite sure they do not have to be parallel. You cannot tell from this work in which direction they go. E. A. GULBRANSEN*—Were any pycnometric measurements made to check the lattice parameters of the alloys ? M. B. BEVER—I did not hear any-

Jan 1, 1950

Owing to circumstances which are entirely unavoidable, the cost of rendering to Institute Members the services which they have been ac-customed to expect from the Institute has increased enormously, especi-ally during the past year. The cost of printing has increased 20 per cent. and another 30 per cent. is expected. There is no recourse; the Institute must pay this or cease publishing. The increase for supplies and office force will be very great. Justice to our employees, whose cost for living expenses has risen by leaps and bounds, demands an increase in. wages, wholly aside from the fact that the employees need not and will not stay. The Institute is, therefore, faced with the alternative of greatly re-ducing its service to the members or else of asking from them a small increase in clues. An amendment to the Constitution has been offered by the members increasing the clues to $15 per year, which cannot become effective until 1921. This still leaves us as the engineering society with the lowest annual clues, except only one, whose dues are $15 per year. To help meet the immediate emergency, the Directors have exercised the authority vested in them by the Constitution and By-Laws and requested the members to pay $3.00 for the Transactions to be issued during the year 1920, which is very much less than the cost of publication. It is the opinion of the Board that the members will prefer to pay this slightly additional expense rather than to have the Institute take a backward step in respect to the services which it is rendering, and which has been increasing constantly in amount, as well as in unit cost, during the past seven or eight years.

Jan 12, 1919

By Robert E. Hochscheid

The subject article appears in the February, 1978, edition of Mining Engineering, and on page 190 carries the statement, "As most operators know, in a Water-Only cyclone, ability to adjust the vortex finder is quite important due to the sensitivity of this type of operations to variance in feed conditions and having to take them apart to make this adjustment is always a nuisance." Our experience as a manufacturer and supplier of Water Only cyclones does not agree with the above statement, and we offer the following brief discussion. Our company finds that the sensitivity of the Water-Only cyclone is a function of the fineness of the coal being washed, with the sensitivity to vortex finder length being greatest for coals coarser than 3/4-in. and virtually insensitive to raw coal finer than 1 mm. For coals finer than 1 mm, we find that we can use the shortest standard vortex finder in either our 10- or 15- in. Water Only cyclone without exception. For coals 5/8-in. x 1 mm ceramic vortex finders of fixed length have been satisfactory in all cases following an initial testing period in which the length was determined. Coals coarser that 5/8-in. are more sensitive to the vortex finder length, and two installations handling coals coarser than 1-in. continued to experiment with vortex finders of various lengths long after the initial startup period. For coals of all sizes, final adjustment of product quality has been achieved by determining the optimum size of apex orifice, which is accessible and readily changed, if necessary. Comments above assume no unusual change in the coal being washed or the required quality of clean coal.

Jan 1, 1979

Data about production are very meager. In this county from the earliest days until after the Civil War, the amount of coal used locally greatly exceeded that shipped on account of the iron produced; for many years the furnaces used raw coal for melting the ore. In 1846 it was stated that in this county one ton of iron required three tons of iron ore and three tons of local coal used raw.1 In 1864, eleven furnaces in Pennsylvania using 102,230 tons of raw coal produced 44,671 tons of iron, or 2.3 tons raw coal per ton of pig iron .2 This was probably as good a record as was made, as nearly all furnaces changed to coke some years later. Neither of these figures include the coal used for steam and other purposes around an iron plant. The Beaver and Erie Canal was opened in 1845 and the shipments shown from then to 1865, inclusive, are of coal received by the canal at Erie, and do not include any used at local points along the canal. From the completion of the Erie and Pittsburgh Railroad in 1864 the tonnage shipped by canal decreased. rapidly, and, while the canal shipments after 1864 are supposed to be those received at Erie by canal only, they may include some rail tonnages. Tonnages on Erie and Pittsburgh Railroad may, and probably do, include some used locally; those on the Jamestown & Franklin Railroad do not. It is likely that both canal and Erie and Pittsburgh Railroad figures include some coal originating in Lawrence County, and possibly a little from Beaver County. These tonnages are not duplicated in the data for either of the other counties. Not all of the railroad reports can be found now.

Jan 1, 1942

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

The authors give a definition of the various types of corrosion that may affect a metallic conductor buried in the ground, namely: 1. The metallic conductor may be attacked by the surrounding soil. This phenomenon is purely local and is called by them soil corrosiveness. 2. The metallic conductor may connect two regions of the ground when the electrolytes have a different composition. An electrical current will then be generated and certain zones of the conductor will be oxidized. This is autogalvanic corrosion. 3. Stray current may flow in the ground and enter the conductor in certain sections and leave it in others, thus causing oxidization in certain zones; this is electrolytic corrosion. The soil corrosiveness has been studied extensively by the United States Bureau of Standards and the authors give a summary of the work carried out and results obtained along this line. In autogalvanic corrosion it has been shown, by the investigation of buried pipes, that the zones of corrosion are associated with the zones of egress of the electric current (anodic zones). The location of these zones can be determined by measuring at the surface of the ground the difference of potential that exists along the path of the pipe. This work is performed easily and quickly with the apparatus invented by the authors for the exploration of conductive orebodies. The problem of electrolytic corrosion is a difficult one because it is a question of stray current which may vary in direction and intemsity at every instant. Therefore the components of the electrical field must be known at a given station and compared with the components of the clectrical field at another station, at the same moment. This is achieved by a rccording apparatus that will register the variations of the intensity of the electrlc current along two rectangular directions, during several minutes

Jan 1, 1934

J. S. UNGER, ? Pittsburgh, Pa. (written discussion ?).-Firebricks intended for, the same purpose, but supplied by different manufacturers, may be of entirely different clays, contain different proportions of flint, calcined and plastic clays; the particles may vary widely in size; the water used to make the brick will vary; the pressure in molding will vary, depend-ing on whether the brick is hand made or power pressed; and the degree of burning in the same kiln will differ. These variables affect the melting point and the strength of the brick when heated. An important property, of a firebrick is its ability to resist heat and, at the same time, weight or load without serious deformation. The soft-ening point and the melting point of a firebrick may be several hundred degrees apart, and two bricks may show considerable difference in their softening points, but the melting points may be approximately the same. Bricks are not usually employed at temperatures close to their melting points. If they must withstand very high temperatures, the firebrick is discarded and a brick of more refractory material is used. Under these conditions' it is doubtful whether the determination of the melting point of a brick has much practical value. If the determination of the melting point is necessary, the test should he made on a portion of the original brick and not on a specially prepared sample. A small triangular pyramid with a base about 1 1/2 in. and 3 in. high can be sawed from the corner of the brick with a thin-bladed car-borundum wheel, without injuring or destroying the size of particles, the bond, or degree of burning of the original brick. This specimen can then he compared with standard Seger cones or tested by any other method desired.

Jan 12, 1919