Search Documents

By S. W. Parr

FROM a study of sulfur with reference to its specific combination in coal, published as University of Illinois Bulletin No. 111, 1919, it is now possible to determine the various forms of this constituent with a good degree of accuracy. This fact suggests two questions: (1) Are the same analytic methods applicable to coke? (2) Is there any correlation between the forms of sulfur as it occurs in coal and the residual sulfur found in the finished coke? The answer to the second question might be helpful in answering a still further question as to what chemical route the sulfur travels during the carbonization process. While the special studies along these several lines are by no means complete, a few preliminary statements are herewith presented. They may, at least, prove suggestive of further possibilities from a continuation of research along these lines. There is no reason, chemically, why the analytic methods devised for coal should not apply to coke and a fair amount of experience in connection with such use affords confirmation of this statement. The procedure in the case of coal may be briefly outlined as follows; Combinations of sulfur as sulfate, or sulfides other than FeS2, are readily dissolved without disturbing either the pyrite sulfur or the sulfur that is in organic combination by means of dilute hydrochloric, acid-1 part of concentrated HC1 to 10 parts of water or approximately 3 per cent. acid. Digestion at 60° C. for 24 hr. insures the complete removal of the sulfur thus combined. In freshly mined coal the amount of such sulfur is very small; weathering processes, however, may very materially increase the amount of sulfate present.

Jan 9, 1919

By H. H. Campbell

In the extending employment of open-hearth steel for structural purposes, it is a matter of prime importance that the test-piece shall represent with practical accuracy the characteristics of every portion of the heat from which it comes. In ordinary practice this homogeneity is assumed; but inasmuch as leading exponents of the revolving-hearth system have claimed that a reasonable uniformity could be obtained by their method alone, it may be pertinent to offer a few facts on the subject. The following heats made by the Pennsylvania Steel Company, for bridge-work, were tested by casting two four-inch ingots, one being taken during the first third and the other during the last third of the cast. Test-pieces obtained from these small ingots usually give results inferior to those obtained from larger sizes; but for purposes of cornparison they are equally conclusive. Many of the tests were made for experimental purposes within a few hours of the time of rolling, and before sufficient time had elapsed for the usual molecular redistribution necessary for the best results. All the tests were made on 3/4-inch rounds just as they left the rolls and without annealing; the results, therefore, are subject to the errors caused by variations in the diameter, and in the temperature at which the bar was finished. The tests from any one heat, however, were always nude as nearly as possible under the same conditions; and inasmuch as these data include the results of every heat so tested, and inasmuch as the errors could not by any chance always support any single theory, we may be certain that the unanimons testimony of the experiments indicates a valid conclusion.

Jan 1, 1886

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By P. E. Demmler

PHOSPHORUS combines with copper in various proportions, forming true alloys, some of which are of commercial importance. These materials find wide application as deoxidizers and as a means of introducing phosphorus into other alloys, as in phosphor-bronze. Phosphor-coppers containing 10 and 15 per cent. of phosphorus are the commercial grades that are most generally offered. Each has certain advantages when used in making other alloys. The 10 per cent. grade of phosphor-copper has an advantage over the 15 per cent. in that it has a much lower melting point and can be prepared by certain methods with a much lower loss in phosphorus. The 15 per cent. grade has the advantage of lower freight rates per unit of phosphorus and, by the method to be described, a uniform product can be prepared with practically no loss of phosphorus. Alloys of copper and phosphorus containing any desired percentage of phosphorus lower than 15 per cent. can be prepared by melting together the requisite amounts of copper and 15 per cent. phosphor-copper. Processes for making phosphor-copper may be divided into two classes as follows: (1) Those depending on the smelting of phosphate rock or superphosphate of calcium with copper or copper-bearing materials, and coal or other carbonaceous material; (2) those depending on the direct combination of metallic copper and elemental phosphorus. A number of formulas for preparing phosphor-copper according to the first method have been published. The Metal, Industry' gives-the following: Superphosphate of calcium, 60 lb.; granulated copper, 301b.; finely powdered coal, 10 lb. Similar formulas are given by Brannt2 and others, and detail 'variations are covered by patents, such as those of L A Jeffs3 and H A Webster.4

Jan 8, 1920

By Richard P. Rothwell

Though coal has been mined in this country for more than a century, no systematic effort was ever successfully made to ascertain the total amount produced. The production of the Cumberland Basin, Md., and the shipments from the anthracite fields of Pennsylvania, have been placed upon record, thanks to the intelligence and foresight of Mr. C. Slack in the former case, and to the late Mr. B. Bannan in the latter. For some of the years between 1822 and 1842, the production of the Richmond Basin was reported by Mr. R. C. Taylor, but since that date till the author undertook this work it was impossible to obtain any statement of the production of this field. A few of the newer fields, such as that of Mt. Diablo, Cal., have been fully reported, and a few of the newer States have also had this service performed by some intelligent private individuals; but no statistics of coal production have ever been collected either by the State or General Government, if we except the returns for the years 1869—70 of the census report. During the year 1875, by great exertions, I succeeded in obtaining, and July 3d, 1875, gave in the Engineering and Mining Journal what, " though not an accurate statement of our coal production," was " by far the most full and reliable that had ever been published." Though that report showed the production of bituminous coal to be 23,630,094 gross tons, or about six million tons more than had ever before been reported, it was in reality two and a half million tons below the actual output. The more full returns I obtained for 1875 gave many figures for 1874

By C. S. Herzig

In the Engineering and Mining Journal of Jan. 27, 1900, there appeared an article by Fred T. Greene, describing a method of measuring stopes by the use of strings, a clinometer and a tape. In the early part of 1899 I had occasion to use a somewhat similar method, for the purpose of accurately ascertaining the volume of a very irregular drift connecting two mines. This drift was an important factor in a lawsuit for $150,000, in which it was necessary to determine accurately the volume originally occupied by the material extracted from the drift. While it is unnecessary to give all details of the controversy, some explanation of the conditions is required for a clear understanding of the following description. This drift was started by the a E." Co. from its workings, in about 7 ft. of ore, and headed toward the " G " property, the plan being to extract all the ore between foot- and hanging-walls, but to take out nothing but ore. As the " G." workings were approached; the ore-body became very irregular and much thinner. It was, however, very closely followed, and where the drift broke through into the " G." workings, the hole was only 11 inches high by 14 inches wide, or just about the size of a man-hole in a boiler.. Thus, this connection-drift tapered sharply; and the very irregular foot-wall sloped toward the " G." workings, and entered them at a place where the stope was only about 3 ft. high, and the ground had already commenced to cave. It may be added that the ore-body was a nearly flat deposit of lead carbonate in limestone, the ore and gangue being quite soft. I was called upon by the " G." people to make the survey

Jan 1, 1901

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By R. W. Brauchli

During the last few years the compila-tion of formation logs from rotary well cuttings has become common practice among petroleum geologists. This meth-od has undoubtedly furnished a great amount of information valuable for both scientific and commercial purposes. How-ever, in spite of its great usefulness it has certain drawbacks, principally in the contamination of cuttings by cavings. In extreme cases this contamination can reach such proportions that it is next to impossible to draw conclusions with any degree of certainty as to the nature of the formations penetrated by the drill. This difficulty was frequently encoun-tered during the development of the Okla-homa City Field. In many cases where Wilcox sand-the most prolific sand of this field-was drilled, the samples con-sisted almost entirely of shale cavings with only traces of sand. In order to obtain more reliable knowl-edge of the formations encountered while drilling it is therefore necessary to resort to more coring, and above all to improve our present methods of coring. With this in mind a study has been made of the results of coring in the Oklahoma City Field, and the present article is mainly confined to a statistical analysis of the relation between recovery, diameter of cores and drill pipe, length of cores and a few other factors. Most of the coring in the Oklahoma City Field was done during the early part of, the development. A total of around 18,000 feet or 0.3 per cent of the total footage drilled before February, 1932, has been cored, and about 80 per bent of the cores were taken in the Simpson formation at a depth below 6,000 feet.

Jan 1, 1933

By Richard P. Rothwell

THOUGH coal has been mined in this country for more than a century, no systematic effort was ever successfully made to ascertain the total amount produced. The production of the Cumberland Basin, Md., and the shipments from the anthracite fields of Pennsylvania, have been placed upon record, thanks to the intelligence sand foresight of Mr. C. Slack in the former case, and to the late Mr. B. Bannan in the latter. For some of the years between 1822 and 1842, the production of the Richmond Basin was reported by Mr. R. C. Taylor, but since that date till the author undertook this work it was impossible to obtain any statement of the production of this field. A few of the newer fields, such as that of Mt. Diablo, Cal., have been fully reported, and a few of the newer States have also had this service performed by some intelligent private individuals.; but no statistics of coal production have ever been collected either by the State or General Government, if we except the returns for the years 1869-70 of the census report. During the year 1875, by great exertions, I succeeded in obtaining, and July 3d, 1875, gave in the Engineering and Mining Journal what, "though not an accurate statement of our coal production," was " by far the most full and reliable that had ever been published." Though that report showed the production of bituminous coal to be 23,630,094 gross tons, or about six million tons more than had ever before been reported, it was in reality two and a half million tons below the actual output. The more full returns I obtained for 1875 gave many figures for 1874

Jan 1, 1877

By B. T. Brady, Wilson Blake

One of the more widespread experimental procedures currently used in experimental rock and soil mechanics work involves the use of a short circular cylinder loaded axially between nonrigid end plates1-5 (Fig. 1a and b). It is widely recognized 6 that a number of undesirable features are connected with this test procedure ; the most noteworthy of these is the development of a nonuniform stress distribution throughout the specimen resulting from an elastic mismatch between the specimen and the end plates. In general, the end plates and specimen possess different elastic properties. As a result of this elastic mismatch, the uniform distribution of stress and strain applied to the end plates is altered at the interface, the degree of which is dependent not only on the magnitude of the elastic mismatch but also on whether there is any relative movement between the specimen and the end plate. A convenient measure of the elastic mismatch is the ratio (vp/Ep) / (v8/E3), where v and E are Poisson's ratio and Young's modulus and the subscripts s and p refer to the specimen and end plate, respectively. For most tests that use steel end plates, (v8/E8) is greater than (vp/Ep) ; i.e., the specimen tends to expand or contract laterally more than the end plates. Because of the frictional restraint offered by the end plates, shearing stresses are developed at the interface that, for compression testing, act inward producing a "clamping" effect (Fig. lc). The effect of this "clamping" is to produce a state of triaxial stress throughout the specimen. Fig. Id illustrates the coordinate system and stress nomenclature used. In a homogeneous, elastic two-dimensional plate loaded uniaxially at the edge, a uniform stress distribution is obtained at a distance from the

Jan 1, 1972

By George Mansfield

INTEREST in the reserves of phosphate rock in the United States and their proper conservation has recently been aroused by hearings held in different parts of the country by the "Joint Committee to investigate the adequacy and use of phosphate resources of the United States." This committee was appointed within a few days after a Presidential message to Congress on the same subject, dated May 20, 1938, and began to function almost immediately. Hearings were held in Washington, D. C., Pocatello, Ida., Wilson Dam, Ala., Knoxville, Tenn., and Lake-land, Fla. The resulting testimony, when published, comprised a volume of 1182 pages.1 At the earlier hearings held in Washington and Idaho the seeming disparity between the great reserves of the West and the smaller reserves in the East led to some suggestions as to the desirability of curtailing or even prohibiting the exportation of phosphate rock so that eastern pro-ducers, becoming alarmed, cooperated in making available for the use of the committee information hitherto closely guarded. This informa-tion has provided an opportunity for new studies by official agencies, for a restatement of the reserves of Florida and Tennessee, and for some modification of figures for the Western States. The writer, representing the Federal Geological Survey, was given free access to the Florida material and has prepared for publication a report,2 some features of which are summarized in this paper. The Tennessee material was studied by Dr. G. I. Whitlatch,3 of the Tennessee Division of Geology. Prof. J. Stewart Williams,4 of the Utah State Agricultural College at Logan, has published a recent study of the phosphate resources of Utah and the writer has given some further study to reserves of western phosphate from the viewpoint of including material of lower grade than that hitherto considered.

Jan 1, 1940

The Development of Research and Quality Control in the Modern Steel Plant. By Leo F. Rein-artz. (Metals Technology, April 1943) Blast Furnace and Raw Materials Essential Considerations in the Design of Blast Furnaces. By A. L. Foell. (,Metals Technology, December 1942) Results Obtained from Surveys of Gas at Furnace Tops. By James M. Stapleton. (Metals Technology, January 1943) Physical Aspects of the Dust Catcher, Gas Washer and Precipitator on No. 3 Furnace at Carrie. By C. P. Clingerman and C. J. FleiscH. (Metals Technology, January 1943) Slag Control by Introduction of Flux through Blast-furnace Tuyeres. By Carl G. Hogberg (Metals Technology, January 1943) The Electrical Conductivity of Molten Blast-furnace Slags. By A. E. MaRtin and GerRard Derge. (Metals Technology, August 1943) Some Physical Characteristics of By-product Coke for Blast Furnaces. By CEarles C. Russell and MichaeL Perch. (Metals Technology, December 19+2) Pyrometry at the Coke Oven. By Robert B. Sosman. (Metals Technology, December 1942) Calcination Rates and Sizing of Blast-furnace Flux. By T. L. Joseph, H. M. Beatty and Gust Ritsianes. (Metals Technology, December 1942) The Low-temperature Gaseous Reduction of a Magnetite. By M. C. Udy and C. H. Lorig. (Metals Technology, October 1942) Steelmaking Problems of Total Operation in Steelmaking. By William C. Marshall and Frank G. Norris. (Metals Technology, April 1943) Silicon-oxygen Equilibria in Liquid Iron, By C. A. ZapFFe and C. E. Sims. (Metals Technology, September 1942) Equilibria of Liquid Iron and Simple Basic and Acid Slags in a Rolating Induction Furnace. By C. R. Taylor and John Chipman. (Metals Technology, September 1942) Rapid Analysis of Oxygen in Molten Iron and Steel. By Gerhard DeRGe. (Metals Technology, January 1943) Silver Chloride as a Medium for Study of Ingot Structures. By Karl L. Fetters and Margaret Dienes. (Metals Technology, August 1943)

Jan 1, 1943

By C. L. Dake

Many proposals have recently been made regarding the broadening of engineering education, often with little consideration of the problems their application involves. The chief purpose of this paper is to point out how many and how complex are the questions that absolutely must be answered, in any conscientious effort to solve the problem of liberalizing engineering curricula. Among proposed additions, more training than is now given has been urged in public speaking, report writing, business law and contra s, general finance, money and banking, scientific management, gene ' economics, economic and financial history, social problems, labor pre lems, public ownership, psychology and similar related subjects. T urge in this direction is widespread and persistent. In discussing the blem, the following questions must be given careful consideration, an he absolutely definite conclusion reached: 1. The Present Curriculum Load.—Is this load actually too heavy? In the face of this load, is there room to add broadening subjects to our curricula? Can elimination of present subject matter make room for such additions? Can an elective system accomplish the desired end? 2. Problem of Early Specialization.—Is early specialization a weak ness? Is industry forcing early specialization? Do our varied degrees demand early specialization? Can broadening be harmonized with the present degree of specialization? 3. Graduate Work to Solve the Broadening Problem.—Can we add the desired work in the graduate school? Are the proposed additions of graduate caliber? Is it desired to reduce graduate standards? Can present undergraduate work be removed to the graduate school, to make room for desired broadening courses? Is graduate work normally broadening, or is it specialization ? 4. Importance of Proposed Additions.—Will they increase entrance salaries? Will they increase the engineer's efficiency? Will they raise

Jan 1, 1934

By Oliver Bowles

THE inorganic non-metallic minerals, that is, the non-metallics exclusive of coal, oil, gas and related minerals, constitute the basic raw materials for a number of essential industries. It is estimated that the value of the raw materials in this group produced in 1919, together with certain of the primary products ordinarily manufactured at the mine, exceeded $800,000,000. They are employed chiefly in the building, agricultural, and chemical industries. It has been estimated, by the Bureau of Mines, that approximately 00,000,000 worth of non-metallic minerals and their products were used in the building trades during 1918; with the great increase in building since that date and the increased cost of materials, the value of non-metals used in such industries during 1920 probably exceeded $500,000,000. The chief of these materials are cement, building stone, crushed stone, sand and gravel, clay products, lime, gypsum, glass materials, slate, talc and soapstone. In many of the producing industries of this great group, the waste is so great that the expense of handling it is an important item in the production cost. The utilization of waste is receiving unusual attention in many of the non-metallic industries at present. The most obvious advantages of such utilization are: (1) Conservation of mineral resources, (2) the removal of waste heaps that in many places obstruct development, (3) manufacture of new and useful products, (4) reduced production costs through elimination of a large part of the item of waste-disposal expense. In many industries there is keen competition between producers of various products used for the same purpose, so that advantage will accrue to the manufacturer who is able to reduce his production costs.

Jan 1, 1921

The Development of Research and Quality Control in the Modern Steel Plant. By Leo F. Rein-artz. (Metals Technology, April 1943) Blast Furnace and Raw Materials Essential Considerations in the Design of Blast Furnaces. By A. L. Foell. (,Metals Technology, December 1942) Results Obtained from Surveys of Gas at Furnace Tops. By James M. Stapleton. (Metals Technology, January 1943) Physical Aspects of the Dust Catcher, Gas Washer and Precipitator on No. 3 Furnace at Carrie. By C. P. Clingerman and C. J. FleiscH. (Metals Technology, January 1943) Slag Control by Introduction of Flux through Blast-furnace Tuyeres. By Carl G. Hogberg (Metals Technology, January 1943) The Electrical Conductivity of Molten Blast-furnace Slags. By A. E. MaRtin and GerRard Derge. (Metals Technology, August 1943) Some Physical Characteristics of By-product Coke for Blast Furnaces. By CEarles C. Russell and MichaeL Perch. (Metals Technology, December 19+2) Pyrometry at the Coke Oven. By Robert B. Sosman. (Metals Technology, December 1942) Calcination Rates and Sizing of Blast-furnace Flux. By T. L. Joseph, H. M. Beatty and Gust Ritsianes. (Metals Technology, December 1942) The Low-temperature Gaseous Reduction of a Magnetite. By M. C. Udy and C. H. Lorig. (Metals Technology, October 1942) Steelmaking Problems of Total Operation in Steelmaking. By William C. Marshall and Frank G. Norris. (Metals Technology, April 1943) Silicon-oxygen Equilibria in Liquid Iron, By C. A. ZapFFe and C. E. Sims. (Metals Technology, September 1942) Equilibria of Liquid Iron and Simple Basic and Acid Slags in a Rolating Induction Furnace. By C. R. Taylor and John Chipman. (Metals Technology, September 1942) Rapid Analysis of Oxygen in Molten Iron and Steel. By Gerhard DeRGe. (Metals Technology, January 1943) Silver Chloride as a Medium for Study of Ingot Structures. By Karl L. Fetters and Margaret Dienes. (Metals Technology, August 1943)

Jan 1, 1943

By W. B. Morrison

Anderson, King, and Spreadborough present detailed evidence to show what ~aldwin~' has already pointed out, that, over a relatively small grain-size range (Ad"1/2 ^ 10 mm-'I2, d is average grain diameter), yield point data can fit a number of relationships. Part of the difficulty in obtaining data which reflect only the effect of change in grain size on yielding arises from the fact that in varying the grain size, even though great care is taken, other structural changes are almost certain to occur. In iron alloys, these changes may consist of variations in subgrain size, grain boundary ledge density, and degree of carbon and nitrogen segregation at grain boundaries, all of which are difficult to detect and which may affect yielding, primarily through their effect on dislocation generation. Because of the inherent inaccuracy associated with yield point measurements there is little point in using relatively complex equations to fit data, as was done by Anderson et mnl., rather than the simpler, widely used Hall-Petch equation. In compiling their table of data, it is surprising that they did not include results from certain low-carbon steels,31 in which, as illustrated in Fig. 2, the grain-size range is very much larger than in their Armco Iron. The very fine grains in these steels were obtained by a thermomechanical process. Examination by electron microscopy showed that the grains were separated by high-angle boundarie and contained only an occasional subboundary. The data from these steels obeyed the Hall-Petch equation, and it was shown quite conclusively that they did not fit a d-l or (1-lJ3 relationship. Obviously, a much wider range in grain size than used by Anderson et al. is desirable if we are to determine the true relation between lower yield stress and grain size.

Jan 1, 1969

By William R. Webster

In view of the great interest now taken in the tests of castiron and details of foundry practice, with the number of investigators at work, and recent improvements in the methods of research, it would seem that the time is ripe to attempt the solution of some of the many problems with which iron founders have to contend. Recent papers and discussions on these subjects* have opened up s large field for investigation, and have emphasized the importance of many considerations generally overlooked. With the view of promoting a comprehensive and systematic discussion, I have attempted to tabulate, in conveilient form, some of the most important points for investigation, on the general plan suggested, with such good results, by our former President, H. M. Howe, for the discussion on the Physics of Steel, at the Virginia Beach meeting, last year. This table can, no doubt, be modified or enlarged to advantage, and put in shape to serve as a guide or reminder to all who are interested in this line of work. Suggested Lines for Discussion and Investigation. I.—Correspondence between chemical composition and melting point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: I. Cupola mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6. Kind of mould, green sand (under dif- on 1 E. Chill. ferent conditions of ramming, amount F. Residual stress. of moisture, and skin-dried), dry sand, G. Condition and quan loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum,

Jan 1, 1896

By W. C. Wright

A PRACTICAL program of education for workers of the mining industries is being formulated by the Federal Board for Vocational. Education in cooperation with the States in which this industry is a dominant one. The Federal Government last year passed a law, known as the Federal Vocational Education Act, that provides for the promotion of vocational' education and for cooperation with the States in the promotion of such education in agriculture and trades and industries and in the preparation of teachers of vocational subjects. More than 1,000,000 men in the continental United States are employed in mines and quarries. The following table, from the-1910 Census Report, shows the relative importance of mining and manufacturing pursuits: Manufactures Mines and Quarries Employees 7,405,313 1,109,410. Capital $18,428,269,706 $3,380,525,841 Value of product $20,672,051,870 $1,238,410,322 Of the more than 1,000,000 men employed in mining, almost three-fourths are engaged in the, production of bituminous and anthracite coal; one-fifth, in the production of copper, iron, lead, zinc, and other metals; and the remainder in getting out structural and miscellaneous materials from quarries. The meeting of the needs of the coal-mining industry, therefore, is the problem of greatest importance in the point of numbers to be served. Moreover, the dangers in coal mining are greater than in metal mining. Practically all States have set up educational and technical standards , for the position of foreman, boss, superintendent, etc., and every applicant for these positions must have a certificate of competency. The qualifications, too, are becoming increasingly difficult in the field of technical information. In some States, every miner must have a certificate, which is issued by the mine examining board. only after an oral examination.

Jan 1, 1919

By Richard W. Lodge

In the crucible-method of assaying ores for silver a certain amount of litharge is essential to supply sufficient lead to collect the precious metals. The object of this paper is to point out that the use of a large excess of' litharge in the assay of some ores will give results for silver that are uneven as well as low. So far as I know, however, an excess of litharge does not affect the results obtained in the crucible-assay of ores for gold. The main reasons for using, in the crucible-assay, much more litharge than is required to givc the necessary lead button are: 1, its action as a flux; 2, its action as a desulphur-izer; and 3, its action as an oxidizer, especially on metals like copper and nickel, whereby they are forced into the slag as oxides and thus prevented from passing into the lead button. Hence, by the use of much litharge in the crucible-assay more ore call often be taken than in the scorification-process, and a lead button obtained which call possibly be cupelled at once or after a single scorification. The method is specially advantageous with an ore carrying much copper or similar impurity and poor in silver, when the assayer does not wish to resort to a wet-analysis for the determination of the silver. It is well known that some ores give better results when assayed by the scorification-method, while others give better results by the crucible-method. For several years I have noticed that, when much litharge was used with certain sulphide and arsenical ores, the results were considerably lower than when the scarification-method was used. This fact was more forcibly brought out in connection with certain work carried on this year by Messrs. H. A. Frame and

Jan 1, 1908

By L. A. Tarshis, H. E. Cline

A stability criterion for a lamellar eutectic interface was derived previously1 assuming that the wavelength, A,. of the perturbation which grows most rapidly is much larger than the lamellar spacing. A. This assumption was required to permit averaging of both the interface temperature and composition over the complicated geometry of a lamellae. If this assumption is invalid, as has been suggested.2,3 then the problem becomes too complicated to solve completely. The first of these analyses1 did not calculate the wavelength. A,. of the initially unstable perturbation. whereas the more recent analysis.' which led to a contradiction of this assumption. did not include one of the key factors for determining this wavelength. To rigorously determine the wavelength, the effect of the curvature of the perturbed interface (not considered by either of the above treatments) must be included. By omitting this term, one would be led to an incorrect conclusion regarding the magnitude of A,. but to an accurate criterion for stability as evidenced by the excellent agreement with experimental observations.' In the case of single-phase alloys. the critical wavelength. A,. for instability can be calculated from the Mullins and Sekerka4 (M.S.) analysis which includes the effects of capillarity. In the following discussion, the M.S. analysis is applied to lamellar eutectics and the critical wavelengths calculated for reasonable growth conditions in Pb-Sn eutectic alloys. In order to apply the M.S. analysis to eutectics. one may substitute i) the effective liquidus slope.1 m*. for the single-phase liquidus slope and ii) the ratio of the bulk alloy composition. C,. to the average interface composition in the liquid (Ci = CE where CE is the equilibrium eutectic composition) for the distribution coefficient to give:

Jan 1, 1970