Search Documents

By J. T. Crawford

COAL-CLEANING plants using the launder process generally wash the fine coal (minus 3/8 or minus 5/16-in.) separately in a plant consisting of washing launders or troughs placed one below another and sometimes supplemented by additional washing equipment such as tables and jigs. The coal and its associated impurities enters the feed end of the top launder, with a current of push water. As the material moves along the impurities, being heavier than coal, settle toward the bottom of the launder and are drawn off, with some coal, through "free discharge" boxes to the launder below. These boxes were given their name because their discharge falls freely; that is, it does not discharge into a water seal. Thus the impurities are progressively concentrated in the lower launders until box products are sufficiently free of coal to be discharged to refuse. The overflows of the upper launders go to clean coal while the overflow of the lowest launder, and perhaps that of the one immedi-ately above, is usually recirculated to the plant feed. Thus the bulk of the clean coal is removed rapidly and the impurities are concentrated more slowly. The chief purpose of this paper is to present the cleaning data of such a plant under different operating conditions.

Jan 1, 1940

By C. H. Herty

AN earlier paper on absorption of sulfur by the slag in the basic open-hearth furnace included a brief discussion of the absorption of sulfur during the melting period. The data available at that time showed that the amount of sulfur absorbed by the melting scrap was proportional to the sulfur content of the furnace gases, and the following statement was made: "The conclusion may be drawn from these results that if a gas entirely free from sulfur were used during the melting, any iron in direct contact with the gases would be completely, or nearly completely, desulfurized before it reached the bath proper." The experimental work discussed herein deals with absorption of sulfur by the melting scrap when fuels with both high and low-sulfur content were used. Before taking up the experimental work let us consider the process as a whole as to the "flow" of sulfur. The input of sulfur occurs in: 1, the hot metal charged; 2, the scrap; 3, the stone or lime charged; 4, the ores charged; and 5, the gas. Sulfur goes out of the furnace in the steel, the slag and the gas. The distribution of sulfur in the furnace depends on the sulfur concentration in each of these materials and on the equilibrium conditions between them.

Jan 1, 1926

By W. A. Hoyer, G. A. Lock

Laboratory and field tests have shown that it is feasible to log for copper in a qualitative way using the techniques of neutron activation analysis. Laboratory tests showed that the 0.51 and 1.04 mev gamma rays of 62Cu and 66Cu, respectively, could be diagnostic. However, in the core holes, the detection of copper was limited to 0.3% concentration because of interferences from the 18Si and Al gamma rays. Both stationary and continuous logs were made, but only the stationary data yielded a recognizable copper response. This response consists of a combination of two effects-the direct response from copper at 0.51 mev and an increase in low energy gamma ray absorption due to mineralization. Both low energy chemical (PuBe) and high energy accelerator neutron sources were used for the laboratory and field tests, while the same 2 X 5 in. Nal scintillation detector served for all the tests. Potential improvements in copper detection might be possible with solid state gamma-ray detectors which have better gamma ray resolution but much less detection efficiency. This type of activation logging requires complex equipment and trained personnel to conduct field operations and may find application where coring is difficult or prohibitive.

Jan 1, 1973

By A. P. Svenningsen

DURING the work at the test mill in Morenci, it was determined that a suitable feed for the ball mills could be made by a single pass through a short-head cone crusher. These crushers did not require a closed circuit delivering only a screen product to the mills, such as is the practice in some concentrators. By no means does this mean that the practice in these other concentrators is wrong, but just that the Morenci ore can be most economically crushed and ground in this manner. Therefore, the design of the secondary crushing plant was simply a problem of taking 25,000 tons of ore per 16 hour day from the primary crusher, this ore ranging in size from fine particles to 10 or 12 in., and reducing it to minus 3/4 in. Inasmuch as outages must be contended with in any crushing plant, it was assumed that the crusher would operate at full capacity for approximately only twleve hours per day, which is three-quarter capacity for the 16-hour shift. With this in mind, it was necessary to design a crushing plant which would average approximately 1600 tones per hour for the 16-hour day, or 2000 tons per hour for slightly over 12 hours per day.

Jan 1, 1942

By J. H. Swisher

Two recent papers in this journal1,2 contain experimental evidence for an anomaly in the concentration gradient for tracer diffusion. In both papers, the authors suggest that this anomaly is due to a Gibbs' absorption effect. Their hypothesis is that surface active tracer elements tend to remain in or near the surface adsorption layer, thereby altering the diffusion flux and concentration gradient. It is not clear how the anomaly can be explained in terms of an adsorption effect. Surface tension forces act parallel rather than perpendicular to a surface and therefore should affect only the rate of spreading of surface active agents tangentially across a surface. Frenkel3 has given a short treatment of surface tension as a driving force for surface diffusion. While the equilibrium concentration of a surface active agent at the surface of a solution is known to be higher than in the bulk, its chemical potential is necessarily the same. It is difficult to see how adsorption can result in an anomaly in the chemical potential gradient, which is the driving force for diffusion. A more detailed explanation by the authors of the adsorption mechanism is in order. A similar anomaly does not seem to arise where

Jan 1, 1970

By Horace Pops, Jorge E. Kittl

In a recent study' of the martensitic transformation of Cu-Zn ß-phase alloys, it was noted that the MS temperature at the surface was raised due to the loss of zinc by volatilization. It seems likely, therefore, that the MS temperature may serve as a guide for the measurement of composition. From a knowledge of the dependence of the transformation temperature on composition, 2 it should be possible to detect variations in zinc content which are less than 0.1 at. pct by measuring the MS temperature throughout the sample. It is unlikely that an electron microprobe analysis could detect accurately such small zinc losses because the presently accepted limits of accuracy of the micro-probe analysis in simple ternary systems are of the order of 2 to 5 pct of the amount present.3 In the present study, a composition gradient was produced by precipitating the a primary solid solution, and reheating for a very short time within the ß-phase field. The nominal composition, in atomic percent, of the ternary ß-phase alloy used, 64.2 Cu, 34 Zn, 1.8 Si, was selected because it had an MS temperature of +4°C, thereby simplifying the experi-

Jan 1, 1968

By David H. Browne

Nickel has always been a fruitful mother of problems. Previous to the year 1906 nickel was regarded as an element replacing iron in copper-mattes, and it was believed that the same laws which governed the elimination of iron could be applied to nickel. This conception has lately undergone a complete change, and nickel in all its stages is now regarded as an element replacing copper; in other words, copper-nickel is considered not as two elements, but as one metal. When we commenced our investigations on Monel metal we made a great many experiment* on the conversion of mattes, both high copper and high nickel. We studied closely the composition of the mattes and the changes produced by the blow. We found in all cases certain agreements which me believe are due to some law. Briefly stated, our conclusions are as follows : 1. Nickel is not an element replacing iron in matte. 2. Nickel-copper alloys act in the matte-blow like one metal. 3. Nickel-copper alloys follow, during the matte-blow, exactly the same laws that govern the behavior of copper alone. This brings up the question: What are the laws governing the production of metallic copper, and what are the relations of copper to sulphur and iron during the Bessemer blow?

Jan 1, 1911

By T. S. Fuller

The tensile properties of steels at elevated temperatures have been studied by numerous investigatorsll primarily for the purpose of determining their suitability for structural uses. Tests with this objective have been confined largely to the temperature range of approximately 20" to 500' C., because of the rapidly decreasing tensile strength at the latter temperature. Tests have also been extended to higher temperatures2 for the purpose of determining the most suitable forging range. This temperature range is also of theoretical interest. The phenomenon if increased tensile strength and decreased ductility .in the so-called "blue-heat" range, approximately 200" to 300" C., is well known. It was suggested to the Bureau early in 1926 that a study of the properties of rail steels in this temperature range might prove of interest in relation to the studies of transverse-fissure failures in rails. There were available from another investigation3 several new rails from several different heats made to approximately the same specification requirements, the complete manufacturing histories of which were known. It was decided to determine, at least in the preliminary series of tests, only the ultimate tensile strength, elongation and reduction of area, because of the difficulty, time and cost involved in determining the proportional limit and yield point at elevated temperatures.

Jan 1, 1930

By Lee W. Abramson

INTRODUCTION The design of rock support for underground nuclear waste repositories requires consideration of special construction and operation requirements, and of the adverse environmental conditions in which some of the support is placed. While repository layouts resemble mines, design, construction and operation are subject to quality assurance and public scrutiny similar to what is experienced for nuclear power plants. Exploration, design, construction and operation go through phases of review and licensing by government agencies as repositories evolve. This paper discusses (1) the various stages of repository development; (2) the environment that supports must be de signed for; (3) the environmental effects on support materials; and (4) alternative types of repository rock support. Much of the information presented in this paper was derived from work conducted for Basalt Waste Isolation Project. Most of the information, however, would apply to other hard rock repositories. REPOSITORY DEVELOPMENT AND THE NEED FOR ROCK SUPPORT Repository development can be characterized by five general stages: exploration and design, excavation, waste emplacement, re trievability period, and backfilling. It is helpful to understand these phases of development to see where and when rock supports are required and how the design is verified. The description that follows is simplified. Details have been omitted, and future plans may not conform to this scenario.

Jan 1, 1984

By Harold B. Goldman, Don Reining

The sand and gravel industry is the largest nonfuel mineral industry in the nation (Drake, 1972), Table 1. In 1970, the production of sand and gravel totaled 944 million tons valued at $1.1 billion. California, which leads the nation with more than 140 million tons, together with Michigan, Ohio, Minnesota, Illinois, Wisconsin, and New York, account for 43 % of the total production in the nation. In commercial usage, "sand" applies to rock or mineral fragments ranging in size from particles retained on a No. 200 sieve (0.074 mm openings) to those passing a No, 4 sieve (4.76 mm openings). "Gravel" consists of rock or mineral fragments larger than 4.76 mm, ranging up to 3%-in. maximum size. The construction industry consumes 96% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see the chapter on "Silica and Silicon"). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material which is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster.

Jan 1, 1975

By Charles S. Barrett, Hermann F. Kaiser, Robert F. Mehl

THE copper-silver system presents several points of special interest in the study of segregate structures. The system is simple eutectic, with limited solid solutions terminal with the pure component metals. The extent of solid solubility decreases with decreasing temperature for both the copper-rich and the silver-rich alloys, thus offering a possibility for the formation of Widmanstätten figures and also a possibility for aging after quenching. In contrast to the structures studied previously the structures in this system are unique in their origin, for one terminal solid solution will precipitate the other, and vice versa. In most of the other systems for which crystallographic data on the precipitation (or transformation) process are available, either intermetallic compounds or intermediate phases partake in the decomposition process; the absence of such phases thus distinguishes this system. The lattice structures of the two solid solutions are identical in type, differing in lattice spacing by approximately 10 per cent; because of this it seems difficult if not impossible to predict on the basis of present theory either the outward form of the precipitate or the lattice orientation relationships between matrix and precipitate. The eutectic temperature in the copper-silver system1 is 779° C. At this temperature copper dissolves 4.3 atomic per cent (7.0 weight per

Jan 1, 1935

By A. J. R. Curtis

THE Portland Cement Association was organized more than a third of a century ago by a group of cement manufacturers, to do cooperatively the educational and research work needed to ensure proper use of their product. Specifically, the Association has a threefold purpose: (1) to search out facts to ensure the best possible service from concrete; (2) to give the widest possible circulation to facts affecting the use of concrete; (3) to urge practical application of those facts on actual building projects. An organization of technically trained men conducts many research projects in the Association laboratories, interprets their findings and applies them practically in the field. The net effect of this work has been to improve the design and prolong the life of roads, bridges, industrial, commercial and public buildings, homes, farm structures and concrete products. The results of this technical research and experimentation are made available to the entire construction industry through bulletins and reports. Information is also released to the general public through newspapers, magazines and Association publications. In addition to a1 technical staff in the general office in Chicago, the Association has district offices in 22 cities. Field engineers cover 37 states, the District of Colum-bia and British Columbia, to give service to users of Portland cement.

Jan 1, 1937

By Georges Fleming

The new burden preparation plant of ARBED Luxembourg, Belval- Works, which comprises 2 large sinter strands, is equipped with a process computer connected to a comprehensive process control system. The main jobs done by the computer are the control of the raw mix composition, and thus the monitoring of the stacking of the piles at the bed-blending plant, and the optimization of the sintering process. Among the optimization criteria, quality is considered as the most important. The sinter quality, characterized by the mechanical strength and the state of oxidation, is controlled automatically. The control system which we have dev loped is highly reliable; as a result, the standard deviation of Fe++, for the control of bivalent iron, has been narrowed to 0,5 % and the standard deviation of the IS0 + 6, 3 mm index, for the control of the mechanical strength, has been kept within 1 %. Thanks to these results, the combined savings in fuel consumption at the sinter plant and at the blast furnaces have covered the total costs of the optimization project in 2 years. By applying automatic control, the optimum driving range of the sinter plant has been defined and these new guidelines are used for monitoring the sinter production.

Jan 1, 1977

By O. W. Ellis

CERTAIN alloys1 that, as a result of quenching, are retained in the form of homogeneous solid solution are known to increase in hardness and strength on standing at room temperature or on heating at slightly elevated temperatures. Other alloys" that, on rapid cooling, are held in the form of homogeneous solid solution (as, for example, certain steels) behave in like manner on heating to somewhat higher temperatures. The observed increase in the hardness and strength of these alloys, referred to as "aging" or as "secondary hardness," is widely accepted as being occasioned, either in whole or in part, by the precipitation in submicroscopic form of such constituents as were held in supersaturated solid solution as a result of cooling in excess of a certain critical rate. In earlier discussions of the cause of age hardening or secondary hardness, the question of the hardness of the precipitated particles does not appear to have been raised. At present, however, the general opinion appears to be that age hardening and secondary hardness are occasioned by the precipitation of hard particles within the supersaturated solid substance.3 The authors may be wrong in their belief that the last is a prevailing opinion. Nevertheless, it is thought that the following experiments,

Jan 7, 1924

By H. E. Powell, A. A. Cochran, R. E. Coleman

Infrared spectroscopy, employing the internal reflection method in conjunction with solvent extraction techniques, was used to study surface reactions between aqueous potassium ethyl xanthate and both sphalerite and precipitated zinc sulfide, each activated with aqueous copper sulfate. It was determined that reactions occurring on the sphalerite and zinc sulfide surfaces produce the reaction products ethyl dixanthogen and cuprous ethyl xanthate, some of which are adsorbed on the mineral surfaces. As the pH of the xanthate solution increased from 5.6 to 11.0, the amount of cuprous ethyl xanthate on powdered sphalerite surfaces decreased and the amount of ethyl dixanthogen first increased and then decreased. It is generally accepted that the collector potassium ethyl xanthate will not float the mineral sphalerite (ZnS). However, Gaudin1 showed that sphalerite readily floats if activated with certain metal cations before exposure to the xanthate. Copper sulfate (CuSO4) was found to be the best activator for sphalerite. The over-all flotation reagent reaction, as given by Gaudin,3 is as follows: While this is the over-all reaction, the exact mechanism of the reaction and the intermediate compounds that may be formed are not yet known with certainty. Important work has been done in Russia by Plaksin

Jan 1, 1968

I. PRESIDING OFFICERS. At all Business meetings of the Institute the President, or, in his absence, the Vice-President, or, in the absence of both of them, any other member of the Board of Directors to be chosen by the meeting, shall preside. At all other meetings of the Institute the President of the Council or, in his absence, one of the Vice-Presidents, if present, shall preside II. ORDER OF BUSINESS. At each Business meeting of the Institute the order of business shall be as follows 1. Reading of minutes of preceding meeting. 2 Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Election of Members of the Council. 7. Reports of Standing Committees. 8. Reports of Special Committees. 9. Special Orders 10. Miscellaneous business. This order of business may be changed by a vote of a majority of the Members and Associates present in person or by proxy. The usual parliamentary rules shall govern all meetings of the Institute except in cases otherwise provided by the Constitution or the By-Laws. At all sessions of the Institute other than business meetings, the order of proceedings and the time of adjournment, shall rest in the discretion of the presiding officer

Jan 1, 1923

By C. Schlumberger

LAST year the authors presented a paper that discussed the various electrical measurements they perform in drill holes, which they name "electrical coring."' The object of the present paper is to give a brief account of the points of scientific interest that have been elucidated by further field work and laboratory research, as well as the economic, results that have been attained recently. The practical examples given in this paper are drawn, for the most part, from the field work performed in Russian oil fields during the years 1931 and 1932. This is due to the fact that, thanks to the comprehensive cooperation of the Russian geologists and scientists, the authors are allowed to make public a large amount of recent information. In other countries in which the authors are engaged in similar work, the competi¬tion between private companies makes it imperative, for a considerable lapse of time, to avoid publication of the results obtained. The following points will be discussed successively, under sepa-rate headings: 1. Electrochemical phenomena in drill holes. 2. Stratigraphic correlations and tectonic studies. 3. Relations between the productivity of oil horizons and their electrical resistivity. 4. Location of coal seams. 5. Summary and conclusions.

Jan 1, 1933

By Stephen Birch

THE Chitina mining district of Alaska is located at the headwaters of the Chitina and Copper Rivers. At present, the only producing min-ing properties are the mines of the Kennecott Copper Corpn. and the Mother Lode Coalition Co., which are situated 196 miles from Cordova the port of entry. The first claims, later acquired by the Kennecott Mines Co. and afterwards transferred to the Kennecott Copper Corpn., were discovered in 1900. The Copper River & Northwestern Ry., which connects the mines with tide water at Cordova, was completed in the spring of 1911. Contemporary with the construction of the railroad, aerial tram equipment was brought to the mines by pack train and a tramway, 3 miles, long, connecting Bonanza mine with the proposed railroad terminal, was finished, enabling shipments of high-grade ore to be made immediately on the completion of the railroad. A mill to treat the lower grade ore was begun the same year. The Kennecott company's holdings consist of 111 mineral claims. The Mother Lode Coalition Mines Co., which is controlled by the Kennecott Copper Corpn., owns 73 claims adjoining the Kennecott holdings. All data on operations and geology refer equally well to the Mother Lode property.

Jan 1, 1924

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

The steady-state operation of an isothermal, counter-current reactor in which a mouing bed of hematite particles is reduced by hydrogen has been modeled mathematically using a generalized single-particle kinetic formulation for topochemical reduction with formation of the intermediate oxides, wustite and magnetite. Reduction prof iles have been generated for various oper- REDUCTION of iron ore, as practiced industrially, approaches counter current, granular-bed operation. The total process is extremely complex. Quite under- ating conditions selected to demonstrate the influence of major variables such as gas and solid flow rates, bed length, and particle size. These profiles illustrate , among other things, that the reducing-gas requirement in a countercurrent bed hinges upon the iron-wüstite equilibrium or 'pinch-point" in much the same way as in a staged reactor. standably, nearly all research has been focused on reduction of single particles of oxide under controlled conditions. While this approach simplifies the problem by eliminating interparticle interactions, the remaining intraparticle transport and kinetic processes still constitute a most formidable challenge. Only within the last few years has knowledge of single-particle reactions been developed sufficiently to make modeling of counter current-bed reduction a realistic and useful study of process behavior. The authors have analyzed1"3 extensive laboratory

Jan 1, 1969

By Ralph W. Bailey, William B. Price

ARSENIC, antimony and phosphorus are now used in the brass industry as standard inhibitors in preventing dezincification in [ ] condenser tubes. This subject has been thoroughly covered by Barry,1 who described the testing procedure by total immersion of suitable specimens in a I per cent cupric chloride solution at definite temperatures. Effects of dezincification were then determined by loss in tensile strength and elongation of the test specimens after definite periods of immersion. In the crystallography of the chemical elements as tabulated by William Hume-Rothery,2 phosphorus (metallic), arsenic, antimony and bismuth are placed in group V-B and the type of crystal lattice for arsenic, antimony and bismuth is given as rhombohedral. The Metals Handbook3 [ ] lists them as "rhombohedral hexagonal," with the additional notation that for arsenic this is the ordinary form at 20°C.; other modifications known or probable at other temperatures. In view of these statements and of the fact that phosphorus, arsenic and antimony are effective in increasing the resistance to dezincification, it was natural to assume that bismuth would act in the same manner. A series of tests was therefore carried out employing the methods described by Barry. Much to our surprise, bismuth did not inhibit dezincification, but rather seemed to accelerate it. Tensile-test speci-

Jan 1, 1942