Search Documents

By R. J. Wasilewski

The resistivity of single crystal and of polycrystalline metal has been determined between 77° and 1500°K. At comparable purity, the resistivity of the poly crystalline metal differs from that calculated from the axial resistivity values. The observed anisotropy is briefly discussed. A zone refined titanium rod was obtained from F. J. Darnell.1 The hardness of this material varied between 52 and 64 Bhn, indicative of its high purity. Single-crystal specimens were cut out from a few large grains, elongated predominantly along <1120>. Resistance measurements were taken with specimens immersed in liquid nitrogen, solid CO,, and acetone, and at ice point, and then recorded continuously between room temperature and 1200" to 1250°C, throughout at least one full heating and cooling cycle at a rate of l° to 3°C per min. Four probe measurements were taken using spot-welded Pt wire 0.003 in. in diam as potential terminals, and the electromotive force drop was determined poten-tiometrically. A standard resistance, in series with the specimen, served to determine the dc current (generally about 80 ma) in the circuit. In order to eliminate spurious thermal electromotive forces, the circuit polarity was automatically reversed at 5-min intervals, and the mean of the two adjacent readings taken as the true electromotive force value. The discrepancy between the readings at reversed polarities was generally of the order of a few µ v, as all the spot-welded joints were contained within a volume of some 5 mm cube. The relative resistance (R T/R 273o) variation with temperature is tabulated below, and shown in Fig. 1, as measured during the first heating run. The discontinuous drop in resistance, corresponding to the a — ß transformation, started for both initial orientations at 1170°K; i.e., some 15°K above the accepted value of 882°C (1155°K). Judging by the temperature ranse of transformation—some 30°K for the single crystal and 20°K for the polycrystal-line specimen—this difference is believed caused by the solution of the oxygen present initially on the surface of the specimens. The general trend of the resistance vs temperature shown in Fi,;. 1 is in qualitative agreement with that previously reported for polycrystalline titanium metal. 2,3 Significant anisotropy is, however, indicated by the crossing over of the curves for <1120> and <0001> orientations at 273°, 650°, and 1000°K. This difference is most startlingly shown in Fig. 2, where instantaneous temperature coefficients (l/R273 x dR /dT) are plotted for both the first heat-

Jan 1, 1962

By Charles C. Hawes

DETERMINATION OF SILICA OXIDE iron ores usually are found in intimate association with silica and phosphorus compounds. Their quantitative separation and purification sometimes present difficult problems to the chemist. Silicic acids may represent various degrees of dehydration. They are exeedingly weak, but combine with metallic oxides and form some of the most stable oxides in nature, the silicates. When iron ores are treated with hydrochloric acid, they yield practically all their iron. However, apart from rare exceptions, varying amounts of insoluble residues of silica, alumina, lime, magnesia and compounds of phosphorus, sulphur, titanium, chromium and others will be left. If the oxides of silicon, aluminum and titanium are present in small quantities, the insoluble residue is generally very small, but the presence of these oxides is more usual in larger quantities. Therefore, only a special treatment can break the bond between these elements. Ore Residues Acids remove the soluble constituent of the ore, leaving the insoluble residue, which chemically is rock or gangue and must be treated accordingly. Alkali carbonates are used frequently to break up the residue, but other fluxes have also been recommended, such as a number of lead and boron salts. The introduction 0f these salts, which offers certain advantages, requires, however, their removal before the other constituents can be analyzed, and this elimination is sometimes difficult. Usually in quantitative analysis silicates are dissociated by fusing them in a platinum crucible with sodium carbonate, thereby forming sodium silicate, Na2SiO3, sodium aluminate, Na2Al204, sodium titanate, Na2TiO3, and carbonates of other elements. All the carbonates are soluble in hydrochloric acid, but also some silicic acid is formed that must be rendered insoluble. To this end the solution is evaporated several times, as the first evaporation still leaves as much as 5 per cent of the silica soluble. Even after a number of evaporations, minute quantities of silica may be found with the iron and alumina present. Perchloric Acid as an Agent for Dehydrating Silicic Acid Perchloric acid, HC104, (60 per cent), has been used for years as a solvent, but few chemists have used it to dehydrate silica. It is derived from anhydrous perchloric C1207, which is most unstable and dangerous. Perchloric acid is a strong oxidizing agent, which boils at 203°C. It is more effective in rendering silica insoluble than any other known agent, and most rapid in action. After perchloric acid is added to a mixture containing silicic acid, the resultant solution is

Jan 1, 1945

By Franz R. Dykstra

DEFINITIONS The ores of iron are classified in three general categories: direct shipping, concentrates, and agglomerated-i.e., pelletized or sintered. Direct Shipping As the name implies, direct-shipping ores are shipped as mined or, perhaps, after screening. Generally, direct-shipping ores are hematitic (R203), magnetitic (R304), or limonitic (2Fe2O3.3H20) in nature. Grades of direct-shipping ores vary widely. Prices are frequently related to the historical Mesabi standard of 51.5% iron, although certain premium lump ores may contain up to 68% iron. The use of direct-shipping ores is diminishing as the advantages of beneficiated ores become evident and reserves are depleted. Concentrates Where the nature of the deposit and economics allows, certain ores are upgraded. This may include no more than washing and screening, or may be as elaborate as fine grinding followed by magnetic, gravity, or even flotation procedures for separation. Coarser concentrates may be smelted "as is.&apos;; Fine concentrates usually are sold as sinter feed. (Sinter, as used here and in the following, refers to a process by which a fine ore-carbon mixture is agglomerated at elevated temperatures on a direct-fired moving grate to eliminate fines and improve chemical and physical homogeneity.) Agglomerates-Pellets or Sinter The development of economic techniques of mining and concentrating taconite (fine-grained, ferruginous jasperoids) led to the introduction of the iron-ore pellet, which is now becoming the major form in which iron is introduced into the furnace. The tremendous reserves of magnetic taconites of the northern United States and Canadian Precambrian shield had been recognized for many years. A century of mining has seen the reserves of the direct-shipping or "red ores" of the Minnesota, Michigan, and Wisconsin ranges approach depletion. Research started in the 1930s has seen the evolution of motives and techniques to concentrate these stubborn refractory ores. The efficacy of concentrate pellets in iron-making has been such as to induce mines throughout the world to grind, concentrate, and pelletize otherwise shipping-grade ores. Table 14.1A.1 shows typical analyses of iron ore. Marketing-Prices of iron may be quoted on a value per long-ton (2240 lbs) or metric-ton (1000 kg or 2204 lb) basis, or on a value per long-ton-unit or metric-ton-unit basis. One iron unit represents 1 % of contained iron per ton. (Thus, a price of $0.45 per iron unit for ore containing

Jan 1, 1976

By E. T. Turkdogan, P. Grieveson

Experimental results are given for the rate 0.f solution of nitrogen in y iron in the temperature range 1000° to 1200°C. It is shown that, when purified reacting gas is used, the rate-controlling process is the diffusion of nitrogen into the iron. The difhsiuity of nitrogen in y iron is calculated from the results and the equation logD = —(8800/T) — 0.04 is recommended to represent the temperature dependence of the diffusivity. In some experiments using unpurified nitrogen, solution rates are found to be slower than those attributable to a solely solid-state diffusion process. Indications are that in the presence of impurities in the gas, e.g., H,O, chemisorption of nitrogen at the surface is hindered and becomes a rate-controlling process for the transfer of nitrogen across the gas -metal interface. ALTHOUGH the solubility of nitrogen in y iron at known nitrogen activities has been well-established,&apos;-a the kinetics of the solution of nitrogen in iron are not known. The work of Darken, Smith, and Filer&apos; indicates that at temperatures below about 1300°C the rate of solution of nitrogen in y iron is controlled by a chemical reaction at the metal surface, while at temperatures above about 1300°C the rate-controlling process is the diffusion of nitrogen in the metal. Fast and verrijps studied the denitro-genization of y iron using wet hydrogen at 950°C and their results clearly indicate that the rate of nitrogen removal is controlled by diffusion of nitrogen in the metal. In Part I of this series of papers, the kinetics of the solution of nitrogen in y iron are discussed in the light of the present experimental work. EXPERIMENTAL Apparatus. The reaction chamber consisted of a platinum wire-wound resistance furnace with a re-crystallized alumina reaction tube. The temoerature of the furnace, which was automatically controlled to approximately 1°C, was measured with a Pt/Pt-13 pct Rh thermocouple and a potentiometer. The temperature distribution in the working zone of the furnace was determined using a calibrated Pt/Pt-13 pct Rh thermocouple and the hot zone was found to be approximately 3 in. long with a temperature variation of * 3°C. A series of experiments was also carried out at 1000°C and pressures above atmospheric using a pressure vessel which was similar in construction to that described elsewhere.1° Materials. Ferrovac E grade iron used in all ex-

Jan 1, 1964

By J. M. Hodge, H. M. Reichhold, R. D. Manning

The work reported in this paper represents the first of a series of investigations of the factors governing notch toughness in ferritic materials. This paper is concerned with two of these factors, namely, the effect of ferrite grain size, and the effect of an alloy content of 3.64 pct nickel. Every effort has been made to hold other variables constant in order to isolate the effects of these two. The compositions chosen for study were 0.02 pct carbon in order to eliminate the variable of carbide distribution, one steel being a plain carbon steel and the other alloyed with 3.64 pct nickel. Both steels were fully killed with silicon, without an aluminum addition, so that the variable of deoxidation practice was held constant. Finally, all samples were water quenched from 1200°F and tempered 24 hr at 300°F in order to hold the quench aging variable constant and to decrease the tendency for grain boundary carbide precipitation. The ferrite grain size was varied by heat treatment over the range of A.S.T.M. grain size numbers of about 2 to 6 in each steel so that the effect could be evaluated individually and the notch toughness of each steel could be compared at comparable ferrite grain sizes. Materials and Experimental Procedure MATERIALS The materials for this investigation were obtained from Battelle Memorial Institute as 250 Ib induction melts which were forged into 134 in. square bars and then rolled into 0.6 in. square bars. Both steels were deoxidized with silicon, the aluminum content being held to a minimum. Check analyses of these materials are shown in Table 1. HEAT TREATMENT FOR GRAIN SIZE The grain size was varied by varying both the cooling rate and the austeni- tizing temperatures. The heat treatments used and the corresponding grain size values are tabulated in Table 2. A semicontinuous network of grain boundary carbide was observed in the microstructure of both the plain carbon and nickel steels in the as rolled condition and an additional heat treatment was necessary to eliminate this variable. Therefore, all samples were water quenched from 1200°F and tempered 24 hr at 300°F as a final treatment before testing. This heat treatment served to eliminate to a great extent the grain boundary carbide network and to hold the quench aging effect constant. IMPACT TESTING Standard keyhole Charpy impact tests were machmed after heat treatment. A bath of acetone and dry ice was used for refrigeration of the samples down to temperatures of —94°F (—70°C) and a bath of either methyl-cyclohexane or isopentane, cooled by

Jan 1, 1950

By James Norman, O. C. Ralston, John Dasher

MOST mineral products are used in the finely divided state, but some are sold in larger sizes. Coal, gravel, metallurgical fluorspar, phosphate rock, hematite, chromite, and other products are sold in sizes coarser than can be treated by many mineral-dressing methods. Gravity separation of coarser sizes by log washing and jigging is probably as ancient as any process now in use. The performance of jigs on a feed with sufficient difference in density of the minerals is excellent, but many families of minerals are too similar in density to be separated effectively by this method. The use of heavy suspensions of fine solids to separate coarse coal from bone and slate has been in use for some years. This separation by sink-and-float was limited until recently to light minerals. Development of galena and ferrosilicon as suspension media, by Minerals Beneficiation, Inc., at Mascot, Tenn., Pitcher, Okla., and Crosby, Minn., under patents granted during and since 1938, has permitted excellent results to be obtained on minerals of very similar densities up to 3.3. This process has been put in the hands of American Cyanamid Co. for exploitation, and further research now in progress may increase the density of suspension obtainable so that separations at a density of 4.0 may be practicable before this is published. The Huntington-Heberlein dense-medium process, developed in England, is also being commercialized in the United States by Sink and Float Corporation. Du Pont has developed a sink-and-float separation using halogenated hydrocarbons as parting liquids; at this writing, the method is used commercially only on coal but has been successful in the pilot plant on many other minerals using tetrabromethane at densities up to 2.95. While these processes were being developed to extend the range of separation by difference in density to the coarser sizes, the Bureau of Mines was engaged in developing a process that will extend the range of separation by difference in wettability up to 2-in. size. War work has pushed aside its further development indefinitely. The results are published here with the hope that some use may be suggested that will justify post-war development, and so that readers that may be able to make immediate use of the scheme may have the information. EARLIER WORK It has been known since the time of Herodotus (B.C. 484(?)-425) that water-repellent particles will adhere to sticky surfaces. That early historian reports the

Jan 1, 1942

Asarco&apos;s Sacaton unit, located near Casa Grande 45 miles southeast of Phoenix, Arizona, was brought into production in February 1974. Ore reserves are estimated at about 48 million tons at 0. 95% copper. Mineralization of the orebody comprises both sulfides and oxides, with minor amounts of gold and silver. Preproduction stripping of 40 million tons of overburden was accomplished in less than two years. Mining is done at the rate of 9,000 stpd ore with a waste-to-ore ratio of 4.6 to 1. 0. The mine is developed on 40 ft benches, and by 1979 underground block caving methods will be phased into the operation at a depth of 1900 ft. Ore is mined in the pit two shifts per day, seven days per week, and is hauled with 85 ton trucks to the primary crushing plant. Trucks dump their loads into a 165 st capacity pocket equipped with a chain curtain which controls the ore flow to the 6 ft 6 in. wide by 24 ft long (2. 0 m by 7.3 m) vibrating feeder grizzly. Grizzly bars are inclined at a 5º slope on the first half of the 0 feeder and 10 on the last half. Grizzly bars have 6 in. (13 mm) spacings which pass 60 to 70% of the mine-run ore. Grizzly oversize drops into a 48 in. by 60 in. (1. 22 m by 1.52 m) primary jaw crusher. Both the grizzly undersize and crusher discharge are collected on a 42 in. (1.07 m) conveyor belt operating 398 fpm (121 mpm) for transport to the 4,750 live st intermediate storage area ahead of the fine crushing plant. Capacity of the Sacaton primary crushing plant is a nominal 1150 stph (1043 mtph). It operates fourteen shifts per week with an effective crushing time of four hours per shift. An economical open-air design was used, but an enclosed operator control room is located on the upper level where the dump truck, feeder, and crusher can be observed. Oversize rocks are removed from the feeder or crusher by the 10-ton bridge crane. Direct operating costs for this well-designed primary crushing plant, including labor, power, supplies, and maintenance, are only 3.5 cents per short ton. An interesting feature of the Sacaton orebody is that the non-sulfide copper minerals, which are less prevalent than the sulfides, occur intimately with the sulfide minerals; for this reason, all ores as mined are treated in a flotation circuit using sulfidizing methods for oxide recovery.

Jan 1, 1978

By D. R. Miller

Internal friction and elastic modulus variations in electrorefined titanium, iodide refined titanium, and alloys of the latter material with oxygen, nitrogen, aluminum, and zirconium were investigated. No oxygen peak was detected with electrorefined titanium but, provided precautions were taken to prevent increases in background damping, an oxygen peak at about 410°C could be resolved with each of the other materials. An additional partially resolved peak was observed at 500°C in a Ti-N alloy. An anomaly in the variation of rigidity modulus with temperature was observed. Possible mechanisms for the formation of any oxygen peak have been discussed. PRATT, Bratina, and Chalmersl investigated the internal friction of commercial purity titanium and alloys of this material containing 1.5, 3.5, and 4.5 at. pct O. With commercial titanium the internal friction curve consisted of two components, a background which increased steadily with temperature and a peak at about 600" C which was due to grain boundary relaxation. In the Ti-O alloys, however, an additional internal friction peak was observed at 430" to 450°C and, since this peak increased in height as the oxygen content was increased, it was thought to be associated with the presence of oxygen. The diffusion of oxygen in titanium at temperatures between 300" and 500° C is believed to have marked effects in its tensile properties2&apos;3 and the present internal friction measurements were undertaken to obtain further information on this diffusion, using material of higher purity than that of Pratt et d. and an apparatus of very much greater sensitivity. In the course of the investigation a number of important limitations on the work of Pratt et al. were revealed and results have been obtained which emphasize the need for ensuring that in this type of experiment, internal friction is independent of strain amplitude and that the values obtained are reproducible. 1) MATERIALS AND APPARATUS The basis material from which the majority of the specimens was prepared was iodide-refined titanium, the major impurities in which were oxygen and nitrogen—the metallic impurities being present at concentrations less than 0.001 at. pct. The hardness of this material after arc melting, forging, and swaging to rods 1/4 in. diameter was Dph = 110. Specimens 10 in. long and 0.020 in. (0.51 mm) diameter were prepared from these rods by further swaging and wire drawing and were finally annealed in vacuo (5 x 10-6 mmHg) for 24 hr at 800°C. The oxygen alloys were prepared from iodide-

Jan 1, 1962

Not many accounts of mining methods or labor conditions in the mines in early days can be found; all that have seemed to be authentic have been included in the preceding chapters. In practically every field opened before 18.10 the first coal was recovered by quarrying, or strip mining, the operations, of course, being by hand and on a very small scale; new places were opened as soon as mining became difficult or expensive. Where it became necessary to drift into the hillsides, the first coal was taken out by sleds, and later by small wagons, the power being supplied by the miner, often assisted by dogs. Wooden rails then came into use with small cars running on them. These cars were very small, usually holding only a few bushels; in the Belleville, Illinois field as late as 1863 cars having capacities of 10, 12, 14 and some as large as 30 bushels were in use. It was not until late in the 1830&apos;s that horses or mules came into use for haulage purposes in the Pittsburgh region, although some had been used in the Richmond, Virginia field at an earlier date. Coal was usually undercut by hand and wedged down, until explosives came into general use, and in nearly every field the coal was forked into the cars, the fine coal, or slack, being left in the mine. Hours worked were very long, but few records remain to show what they were at different places and times; there was undoubtedly a great variation between districts and mines. Roy stated a miner could often produce 5 or 6 tons in a day of 8 or 9 hours in a 5 or 6 foot seam, but in another seam possibly could mine only 3 1/2 to 4 tons. He estimated an average day&apos;s work in a four foot seam at about 3 1/2 tons.1 In a strike in the Belleville field in 1863 it was found that an average skilled miner in the field could probably produce 4 to 5 tons a day.2 This was only the coarse coal loaded and did not include slack. In 1873, a coal undercutting machine was tried at a mine about two miles from Brazil, Indiana, said to be the first coal machine ever invented in the United States. It was run by a 5 H.P. steam engine (later to be changed to compressed air), and consisted of an iron rim, four feet in diameter with movable steel teeth placed about one foot apart. The rim

Jan 1, 1942

By A. B. Tanner

The effects of radon in drillholes on gamma-ray logs have been described by L. S. Hilpert and C. M. Bunker1 Since these effects may cause drastic error in the evaluation of uranium deposits, it is useful to know the conditions under which significant amounts of radon tend to accumulate in drillholes. In the studies described here, atmospheric conditions were found to dominate in the control of the behavior of radon in drillholes in the vicinity of a uranium orebody. The site of the investigation was in McKinley County, New Mexico, about 12 miles north of Grants. Drillholes of 4 1/4-in. diam, on 25-ft and 100-ft centers, penetrate ore in dry rock at a depth of about 100 ft. A geologic log of the drillhole of primary interest is shown in Fig. 1. Gamma-ray logs revealed three zones of ore-grade mineralization in the Todilto limestone. A 6-ft zone, the lowest of the three, assayed 0.20 pct U3O8 by chemical analysis. The limestone ores in this area contain disseminated uraninite and some yellow and orange secondary minerals. Only radon"", a member of the uranium&apos;" series, was measured in this investigation. Radon is one of the chemically inert noble gases and is radioactive by alpha particle emission with a half life of about four days. In this discussion, amounts of radon are expressed in microcuries (1 microcurie equals 37,-000 disintegrations per sec) and concentrations of radon are expressed in microcuries per liter of drillhole air. Samples of air were obtained by lowering a sampling device (Fig. 2) into a drillhole and actuating the device at the desired depth. It was then raised to the surface and the sample was transferred to a storage tube. Within two days the sample was transferred to an ionization chamber, and the activ- ity of radon and its short-lived daughter products was measured at radioactive equilibrium with a vibrating-reed electrometer. The measurements were corrected back to the time of collection and involve errors estimated generally not to exceed + 5 pct to —15 pct. Radon Behavior in a Covered Hole: Fig. 3, a typical log of radon concentration vs depth in the covered drillhole, was made by using values of radon concentration at discrete depths. Continuous logs of alpha-particle radiation in the drillholes showed that such radon logs depict the continuous variation of radon concentration with depth quite accurately. Three features of radon logs were noted: 1) maximum

Jan 1, 1960

By P. Farrar, H. Margolin

The Ti-Pb diagram was investigated in the region 0 to 58 pct Pb and from 500°C to liquidus temperatures. Three reactions were encountered: I—ß?a+Ti Pb at 725 10°C; 2—ß+L?Ti4Pb at 1305+ 10°C; and 3—the possible eutectic L-+Ti,Pb and y between 1200" and 1300°C. LEAD-RICH alloys have been investigated by Nowotny and Pesl,&apos; who used sintered compacts and studied the region from 37.5 to 100 pct Pb by X-ray diffraction analysis. The only phase found in addition to titanium and lead was the hexagonal compound Ti Pb. Alloy systems of lead with metals of the transition group, such as iron, chromium, tungsten, cobalt, nickel, or manganese, generally show little liquid or solid solubility.&apos; Craighead et al.,3 however, indicated that lead is soluble in a and ß titanium to at least 2.1 pct. They also found that approximately 50 pct of the lead added was lost during the arc-melting of Ti-Pb alloys. In the present investigation, are-melting also was used to prepare Ti-Pb alloys and similarly large lead losses were encountered. Experimental Procedure Alloy Preparation: Considerable difficulty was encountered in the melting of the Ti-Pb alloys and a number of experiments were performed before the method described was developed. Alternate layers of lead and titanium were wrapped with titanium sheet and compacted. This "sandwich" was annealed at 300" to 350 °C and was melted according to the procedure described by Cadoff and Nielsen.&apos; Using a low current, 150 amp, and an argon atmosphere, four to eight 10 to 20 sec melts were made on each alloy, with the button being turned over between each melt to insure homogeneity. In the high lead range, the preliminary sintering was found to be of doubtful value and was eliminated. In the region above the nominal composition of 70 wt pct Pb, the alloys prepared in this manner always consolidated into two phases. The outside appeared to be composed entirely of lead and the inside was a Ti-Pb alloy. In order to determine whether this phenomenon was caused by a miscibility gap, master alloys with a nominal composition of 40 wt pct Pb were machined and mixed with various percentages of lead sheet. This mixture was compacted and melted in the same manner as the other alloys. Although these alloys were not homogeneous, they did not show the layering that was observed

Jan 1, 1956

By John B. Mertie

More than 200 minerals are known that contain the rare-earths and thorium. Monazite and bastnaesite, however, are the principal commercial sources of the rare-earths, and monazite is the principal source of thorium. Monazite was in demand in earlier years mainly for its content of thorium, which was used in the manufacture of Welsbach gas mantles; but beginning in the latter part of the nineteenth century, the rare-earths became progressively more important than thorium. Recently, however, the tenor of thorium in monazite has again become a matter of commercial interest. Rare-Earths and Thorium The rare-earths proper are defined by spectroscopists as the oxides of 14 elements with atomic numbers ranging from 58 to 71; but more commonly lanthanum, with an atomic number of 57, is also included, in which case these 15 elements are often designated as the lanthanides. Chemists also include scandium and yttrium as elements of the rare-earths. A second group of elements, beginning with actinium and including thorium, protactinium, uranium, and all the transuranium elements so far produced, with atomic numbers ranging from 89 upward, are chemically and structurally related to the lanthanides, and are known as the higher rare-earths or actinides. Berzelius discovered that the lanthanides could be separated roughly into three groups, based upon the solubility of their double salts, R2(SO4)3-K2SO4-2H2O, in excess of K2SO4. This separation, with the substitution of sodium for potassium, is still used commercially. The double salts of the cerium earths were found to be almost insoluble; the terbium earths, partly soluble; and the yttrium earths, completely soluble. Based upon the degree of solubility, scandium belongs with the cerium earths; and yttrium belongs with, and gives its name to, the yttrium earths. These three groups with their atomic numbers are shown below. [ ] The prevailing state of oxidation for the rare-earths is R2O3, but cerium may readily be oxidized to the tetravalent state, in which condition it may be separated chemically from the other cerium earths. Praseodymium and terbium may also exist with the valence IV, and samarium, europium, and ytterbium may have the valence II. Most of the elements of the rare-earths, however, are very difficult to separate, and their initial isolation required the work of many chemists over a period of 150 years.20 Fractional crystallization, fractional precipitation, and ion exchange are the principal methods so far used, and fractional precipitation is now employed commercially on a large scale. Ion exchange columns are

Jan 1, 1960

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm&apos;s law and d&apos;Arcy&apos;s law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm&apos;s law and d&apos;Arcy&apos;s law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By J. A. Lund, A. M. Lawson

THE structures of quenched eutectoid and hypereu-tectoid Fe-Cu alloys have been examined by X-ray diffraction and by optical and electron microscopy. The relevant portion of the Fe-Cu phase diagram is given in Fig. 1. Several values have been reported for the solubility of copper in a Fe at the eutectoid temperature, including 1.4 wt pct by orton&apos; and 2.13 wt pct by Wreidt and Darken.2 Alloys containing 4.8 and 7.5 wt pct Cu have been prepared from two batches of Ferrovac E iron (0.005C and 0.013C) and electrolytic tough pitch copper (99.90 Cu). Specimens of dimensions 0.8 by 0.8 by 0.1 in. were cut from hot-rolled material, austenitized, and quenched into brine at 25°C. Similar specimens were also cooled in the furnace, after a short soaking treatment at 1100°C, at a rate estimated to be 10°C per min in the temperature range of 900" to 500°C. X-ray diffractometry was performed on quenched and on furnace-cooled bulk specimens using iron radiation. Only a bcc phase could be detected in all samples. Lattice parameters were calculated from measurements on four lines, made up of two resolved high-angle doublets. Comparisons were made against a silicon standard. Results are shown in Table I. Based on X-ray diffraction studies of a series of alloys of lower copper concentrations, orton&apos; estimated that the tattice constant of a Fe at 25°C increases 0.0014A per wt pct Cu in solution. Extrapolating Norton&apos;s data, it may be concluded that all copper was retained in solution in the brine-quenched 4.8 pct Cu alloy, and that approximately 5 pct Cu was also held in solution on quenching the 7.5 pct Cu alloy. Typical microstructures of brine-quenched specimens, as observed by optical microscopy, are shown in Figs. 2 and 3. Precipitation of the E phase (copper-rich) occurred along the y grain boundaries on quenching the 7.5 pct Cu alloy, rendering them readily detectable in the microstructure, Fig. 3. The original boundaries in the 4.8 pct Cu specimens were gener- ally not discernible, however. This indicates that the z phase which was seen in the higher-copper alloy was probably of proeutectoid origin. Thin foils for transmission electron microscopy were obtained from bulk specimens by spark machining to 0.006 in. thickness, followed by electrolytic polishing. Typical transmission electron micrographs

Jan 1, 1967

By R. J. Allio, C. H. Randall

An automatic system for the quantitative analysis of microstrulcture has been developed. The method is based upon a statistical model of microstructure and employs phase intercept fractions as fundamental random variables. Structure-sensitive properties can be related explicitly to parameters derived from the distribution of phase intercept fractions in a matevial. THE properties of mechanical dispersions and of multiphase alloys art: intimately related to the amount, distribution, and intrinsic properties of the dispersed material. In many instances, the amount and distribution of the dispersed substances have greater influence on the over-all system properties than do the properties of the dispersed substance-Such properties as average particle size, particle size distribution, homogeneity of dispersion, volume per cent of dispersed phase, and mean free path between dispersed particles thus become critical in any evaluation of the properties of a dispersion. Unfortunately, techniques for evaluating quantitatively the microstructural characteristics of dis~ersions rapidly and accurately have not been available. If necessary, qualitative or semiquantitative devices can be utilized. Some such devices are based merely upon comparison of the specimens in question with arbitrary standards. Other techniques involve superposition of grids and tabulation of particles observed in different portions of the grid. Still other methods based upon lineal analysis entail counting lines or points at random upon the specimen to be examined; the number of intersections of the line with a given phase, the proportion of line or number of points which are covered by given phase are variously recorded. The mathematical basis for most of the techniques of quantitative metallography have been amply reviewed in the literature.&apos;l2 without exctption, however, the standard techniques for quantitative metallography are either imprecise or are exceedingly tedious to apply. For example, tranverse integrating stage for rapid manual areal fraction measurement has been designed by Smith.3 Howerer, as in the case of any device based upon visual eslimation, operator bias may cause appreciable error. Various flying spot devices, on the other hand register particle size distributions in 2-dimensions, from which it is difficult to derive other properties of the dispersion. Thus, e.g., the 3-dimensional distribution cannot be inferred unless certain rather broad assumptions are made concerning the randomness of distribution and geometrical configuration of dispersed phase. Many limitations to the application of quantitative structural analysis can be overcome by the use of the microdensitometer, which is essentially an automated areal analysis device. Data obtained in the form of a distribution of phase intercept values are

Jan 1, 1962

By E. M. Cox, T. Rosenqvist

IN a recent investigation, carried out at the Institute for the Study of Metals, the affinity of sul-phur for iron, copper, and manganese was studied over the temperature range 700" to 1300°C.&apos; It was found that copper exhibits a rather high affinity for sulphur, especially at higher temperatures; and attention was called to the possibility that copper when present together with sulphur in liquid steel would tend to lower the chemical activity of sulphur and thus interfere with the desulphurization process. It was clear, however, that the data for the equilibrium between pure copper and pure copper sulphide (Cu2S) could not give any quantitative information about the effect of copper when dissolved in liquid steel. The present work is concerned with the activity of sulphur in the diluted range of the binary iron-sulphur system, and with the influence of small amounts of copper on this sulphur activity. This investigation is in principle based on the same method previously described for the binary metal-sulphur studies;1,2 namely, reaction with hydrogen to form hydrogen sulphide. The equilibrium ratio PH2s/Ph2 in the equilibrium gas mixture is, for a given temperature, directly proportional to the sulphur activity. The activity of sulphur in liquid iron has previously been studied by Chipman and Ta Li,3 White and Skelly,4 and recently by Sherman, Elvander, and Chipman.5 Morris and Williams6 have studied the effect of added silicon, and Kitchener, Bockris and Liberman,7 and recently Morris and Buehl,8 the effect of added carbon on the sulphur activity. In present day steelmaking processes the steel bath contains between 0.01 and 0.1 pct sulphur, and the copper content may be as high as 0.5 pct. The equi-librium gas ratio (H2S/H2) would, for such a low-sulphur content, be too low to be measured with the experimental technique we use. It has been shown by previous investigators that the H2S/H2 ratio is closely proportional to the sulphur content up to about 1 pct sulphur. The sulphur activity at very low-sulphur content can therefore be calculated by linear interpolation between 0 and 1 pct sulphur. In order to show the general trend with increasing sulphur content, the present work has been carried out to about 3.5 pct sulphur. As the effect of copper was assumed to be more a function of the Cu/S ratio than of the absolute copper content, the runs with copper were made for certain constant values for this ratio.

Jan 1, 1951

By John R. Lewis

DURING the past few years there has been considerable interest in the sizing and the preparation of the iron ore fed into blast furnaces. Furnacemen know that proper sizing of ore tends to increase the efficiency of the furnace. It has been shown by Joseph1 and his associates that there is a direct relationship between the porosity of an ore particle and the time required for its reduction in the blast furnace. This relationship may be stated as follows: All other factors remaining constant, the time for reduction of a given sample of ore is inversely proportional to its porosity. As a consequence, large pieces of very porous ore, say 3 or 4 in. in cross section, will be completely reduced by the time they reach the hot zone just above the tuyeres, while large pieces of dense, nonporous ore may reach the hot zone with their centers unreduced. This means that for the latter complete reduction will be accomplished by the so-called "direct method;" i.e., where carbon reacts directly with the ore. Some recent work by Philbrook2 seems to contradict this rule. He found that of two unlike ores he studied, the one with the lower porosity reduced more readily. He explained his results as "possibly due to an apparently greater tendency of the `A&apos; ore (lower porosity) to crack during preliminary dehydration and during reduction." This brings his results in line with the rule stated above. It is not the author&apos;s intention to enter into a discussion of the merits of "direct" versus "indirect" reduction. It is enough to say that, in general, indirect reduction is desirable. For the greatest efficiency, Gruner&apos;s theorem3 requires that all reduction in the blast furnace be indirect. Joseph seems to believe this also, because in his recent article on Some Comparisons between Iron Ore, Sinter and Nodules as Blast Furnace Feed&apos; he concludes that: "In general, the carbon in blast-furnace coke is used most efficiently when the largest amount of the carbon charged reaches the tuyeres." However, P. V. Martin,&apos; in an excellent paper, has shown that some direct reduction may actually increase the efficiency of the furnace; that is, increase its rate of production while maintaining maximum fuel economy. For nonporous ores there is more opportunity to have an excess of direct reduction unless the factors that make for indirect reduction are favored; for instance; the proper sizing of the ore particles. Another factor that has an important bearing on the reduction rate, as it is affected by particle size, is the flow of heat into the particle. The ore particle

Jan 1, 1947

By Irving Cadoff, Jack Medoff

THE linear thermal expansions of oriented single crystals of zinc were measured in the range from 20" to 416°C using a Leitz HTV optical lever differential dilatometer. The single crystals, supplied by Dr. J. J. Gilman, General Electric Research Laboratory, Schenectady, N.Y., were prepared from 99.999 pct-purity zinc, and were in the form of rods approximately 2 in. long by 0.15 in. in diameter having the following orientations: x = 1.5, 12, 20, 30, 37.5, 49, 60, 73, and 82 deg where x is the angle between the specimen axis and the (0001) plane of the crystal. From the family of expansion vs temperature curves, the instantaneous expansion coefficients were calculated at 100°C intervals, and Fig. 1 shows a plot of these derived coefficients for each orientation. Coefficients were obtained from the raw data using the chord-slope method. The curves in Fig. 1 indicate a positive temperature coefficient for low x, a negative temperature coefficient for high X, and an expansion coefficient invariant with temperature, amounting to about 43 x 106, for a crystal orientation of approximately 52 deg. From the available data, it is possible to arrive at the values for the axial thermal-expansion coef- ficients a, and a, by extrapolating the curve of the expansion coefficient vs orientation to zero and 90 deg orientations. More precise values for a, and a, are obtained if the instantaneous coefficients are plotted against the square of the cosine of the orientation angle, as shown in Fig. 2. The extrapolated terminal points of the best straight line through the data points of such a plot define the axial coefficients at that temperature. The theoretical justification for the linearity of this curve comes from inspection of a rearranged form of the general anisotropic equation for expansion: ax=a, + (a, -a,)cosZx [1I in which a, is the expansion coefficient in the "c" or [0001] direction and a, the expansion coefficient in the "a" or [ll50] direction. From Fig. 2, the axial coefficients at 100°C, for example, were found to be a, = 13.9 x 10&apos;6 and a, = 62.4 x 10"6 per "C. In the same way, the coefficients were determined for 20", 200°, 300°, and 400°C. This data is summarized in Fig. 3. It is of interest to observe the common intersection of the curves in Fig. 3, which seems to bear out the earlier observation, from Fig. 1, of a

Jan 1, 1964

By E. R. Buchanan, R. E. Reed-Hill

A transmission electron microscope study was made of magnesium single crystals deformed in torsion using the basal pole as the forsional axis. While this type of deformation is predicted to result in the formation of hexagonal networks of screw dislocations, these networks were not observed. The basic dislocation arrangement consisted of arrays of nearly parallel and approximately equally spaced dislocations. The average dislocation density was over an order of magnitude higher than that required to account for the torsional deformation. The observed high rate of work hardening in these crystals is consistent with both their high dislocation densities and the arrangement of dislocations in pile-ups. The experimental observations are also in agreement with the assumption that dislocation sources are activated not only at the surface but at interior locations as well. In considering torsional deformation, Amelinckx and Dekeyser1 postulated that when a torque is applied to a crystal oriented with a glide plane normal to the specimen axis, deformation occurs by the following steps: 1) Nucleation of dislocation sources at or near the specimen surface in areas where the shear stress, resolved along a slip Burgers vector, is a maximum; 2) the screw orientations of the dislocations accommodating the twist move inwards towards the specimen center. If two glide directions lie on the glide plane, the geometry shown in Fig. 1 should result; 3) the screw dislocations that pile up in the central part of the specimen cross-slip to form a grid. At the same time, screws of opposite sign and most edges leave the specimen. Tinder,2 using zinc crystals twisted about the basal pole, independently reached essentially the same conclusions. He suggested a mechanism involving nucleation of ?(1120) screw dislocations at the six points of highest resolved shear stress that lie on the cross-section near the surface. Under the applied shear stress these dislocations were assumed to move inward and interact so as to form a hexagonal network of screw dislocations. Today it is often accepted that rotational slip occurs by a mechanism of the above type, but to our understanding this has never been experimentally proved. This paper reports an experimental study of rotational slip, using magnesium single crystals, that indicates that in this metal rotational slip does not conform well to this mechanism. EXPERIMENTAL PROCEDURES Mechanical Testing. Specimens with a (0002) axis were prepared from magnesium crystals of 99.95 pct purity grown by Jillson&apos;s3 modified Bridgman technique. The crystals were acid machined into cylindri-

Jan 1, 1970