Search Documents

By V. Balasubarmanian, Rajendra Kumar

ISOTHERMAL formation of martensite in a copper-aluminum-nickel alloy was previously reported by Hull and Garwood.' In the present work an attempt has been made to investigate some of the character- istics of the formation of isothermal martensite in binary copper-aluminum alloys containing 14.00 and 14.50 pct Al, respectively. Chill-cast alloys were prepared from OFHC copper and aluminum of greater than 99.5 pct purity. They were homogenized for 24 hr at 950° C. Polished samples were soaked at 1000°C and quenched in water to retain the p phase untransformed; martensite did not form during the quench. The surface was then repolished for isothermal microscopic studies at room temperature. The salient features of the martensitic transformation in copper-aluminum alloys observed in this investigation are: a) The transformation progresses (i) by nuclea-tion at new sites and (ii) by simultaneous slow isothermal growth of existing martensite plates. Slow isothermal growth of martensite has previously been observed by Holden2 in an uranium-chromium alloy and by Hull and Garwood in copper-aluminum-nickel alloy. b) Martensite plates nucleate preferentially at the pin holes formed during the casting of the specimen, Fig. 1. c) Some of the martensite plates pass right through other plates lying in their path, Fig. 1. d) Martensite plates cross grain boundaries without any change in the direction of growth. e) An irregular network of markings, Fig. 2, appears simultaneously with the formation of martensite. It was less prominent in the case of 14.5 pct alloy. The markings may arise due to spontaneous deformation under the lattice strains of the martensitic transformation. Crossing of martensite plates was first observed by Kulin and cohen3 when a high-nickel steel was cooled to 77°K. They suggested that the rapidly advancing plates atquire considerable kinetic energy and strike the obstructing plate with a momentum so as to nucleate the process on the other side of the plate. This, however, fails to explain the present observation where the slow isothermally growing martensite plates cross each other. Such plates would not possess large momentum to bodily displace the obstructing plate. Fig. 1 shows the martensite plates crossing each other without body displacements. This should be contrasted with Fig. 3 of Kulin and Cohen's paper where crossing of plates is accompanied by shearing or body displacements of the plates. The present observations can, how-

Jan 1, 1961

By G. A. Croes, N. Schwarz

This paper reports the results of a series of model displacement experiments carried out for measuring the efficiency of the water-drive process. This series forms a continuation and extension of that described by Engel-herts and Klinkenberg. Detailed information has been obtained on the influence of the oil/water viscosity ratio. The results are represented in the form of a diagram from which both the oil recovery and the water/oil ratio can be easily read off as a function of the total production (oil plus water) for all values of the viscosity ratio M between I and 500. These resu1ts are viewed in the light of the two existing theories on water flooding, viz. that of Buckley and Leverett and that of Dietz. It is shown that if the Buckley-Leverett theory applies, the relation between the relative permeability ratio and saturation, which plays a major role in this theory, (.an be calculated with a high degree of accuracy from the results of the model experiments. Dietz's theory is found to be in agreement with the experimental results in a certain range of circumstances. A discussion of the physical background of the Buckley- Leverett and Dietz theories makes it clear why the latter fails to agree with some of the experimental results. INTRODUCTION For an economical exploitation of oil fields both a rational control of natural (primary) recovery processes and a proper application of artificial (secondary) recovery methods are essential. These require detailed information upon the dependence of the relevant flow processes on the variables by which they are governed. Three methods are available for obtaining this information: (1) (statistical) analysis of actual field data; (2) appropriately scaled model experiments; and (3) mathematical analysis of the physical problem. If sufficient data were available, the first method would, in principle, be the most reliable one, although it has the drawback that the basic relationships between the variables involved are to a large extent obscured by the natural inhomogeneities of most reservoirs. The most profitable procedure seems to be: (a) determining the fundamental relations for idealized reservoirs by methods (2) and (3); (b) checking the consistency of the results obtained by these two methods; and (c) establishing the range of applicability of these methods to actual reservoirs by comparison with the data accumulated under (1). In this paper items (a) and (b) are dealt with for the case of homogeneous loose sands initially saturated

Jan 1, 1956

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.' The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.'

Jan 1, 1964

By K. R. Garr, D. Kramer, A. G. Pard

EXPOSURE of steels to a fast-neutron flux results in helium generation by (n,a) reactions. The elements Fe, Ni, Cr, and N are major participants in the (n,a) reaction and helium concentrations of up to 5 x 10"5 atom fraction could accrue in fuel clads after a year of service in proposed fast reactors.' Such concentrations of helium can severely reduce the ductility of alloys at temperatures of reactor service. The phenomenon of helium embrittlement has been studied in austenitic alloys which were irradiated with particles as a rapid means of producing significant helium concentrations.2-5 The pres-ent work is a continuation of those studies and is concerned with helium effects in a ferritic stainless steel. I) EXPERIMENT Small sheet tensile samples with a gage length of 0.50 in. and a cross-section of 0.009 by 0.040 in. in the gage length were punched from cold-rolled type 405 stainless steel. The composition of the steel used in this work is given in Table I. Prior to helium injection, the samples were annealed 24 hr at 760°C which caused complete recrys-tallization with a resulting grain size of 40 u. This treatment rendered the alloy completely ferritic and carbide particles, 0.5 to 2 uin size, were present at a density of 1 x 1011 cm-3, Fig. 1. These carbide particles were probably a mixture of the M7C3 and M4C types.6 Helium was injected into the samples by irradiation with a particles from a cyclotron, which produced uniform concentrations through the center two-thirds of the sample thickness. Details of this procedure were previously described.' The average helium concentration, as measured on a gas-source mass spec- 11) RESULTS A) Tensile Tests. The results of the tensile tests are given in Table I1 where the values shown are averages of two samples. There was no significant effect of helium on either the yield strength or tensile strength at 550" or 650°C but an increase in both is apparent at 750°C. Samples with helium showed a 20 pct loss in total elongation at 650°C which increased to a 55 pct loss at 750°C. The uniform elongation is not affected by helium at 550" or 650°C but shows an increase at 750°C.

Jan 1, 1970

By Leslie Burris, J. C. Hesson

The diffusivity of uranium in liquid cadmium has been measured as a function of temperature by the capillary -bath technique. The diffusivity measurements were made at 4509 500°, 575º, and 650°C, over which temperature range the diffusivity of uranium varied from 1.3 to 2.3 x 10-5 sq cm per sec. The diffusivity of uranium in cadmium was less than that predicted by the Einstein-Stokes equation. VERY little information is available on the diffusivity of uranium in liquid metals. Bonillal has reported a single measurement of the diffusivity of uranium in bismuth. Measurement of the diffusivity of uranium in cadmium was undertaken, not only to supply data in an area in which a dearth of information exists, but also because of a need for this physical property measurement in connection with mass transfer studies now underway in the U-Cd system at Argonne National Laboratory. The capillary-bath method used in this work has been successfully used by other workers2"4 to obtain diffusivities in liquid metal systems. Although considerable experimental technique is required to obtain reliable diffusivity measurements, the basic information required is only that of temperature, capillary tube length, the initial and final compositions of the alloy in the capillary tube, and the composition of the bath into which the solute element is diffusing. From these measurements, diffusivities may be calculated using Fick's law. The diffusivity equations are presented in the Appendix. Equations which are often used to predict diffusivities in dilute solutions5 are the Einstein-Stokes equation: D= (kT)/(6pµr) and the Eyring equation: D = (?,kT/?y?zp), where D= diffusivity (sq cm per sec), k = Boltzman's constant, T= temperature ("K), p = viscosity (poises), r = radius of diffusing molecule or species (cm), and A,, Ay, and A, are the diameters of the diffusing molecule in the three axial directions. For round molecules, the Eyring equation gives values which are 37r times larger than the Einstein-Stokes equation. In this work, the experimental values were compared to the Einstein-Stokes equation. Experimental values of diffusivities in liquid metal systems usually lie between those predicted by the Einstein-Stokes and Eyring equations. The viscosity values for cadmium were obtained from the Liquid Metals Handbook.6 EXPERIMENTAL APPARATUS AND PROCEDURE The general procedure employed consisted of rapidly immersing in a molten cadmium bath containing a negligible amount of uranium a capillary

Jan 1, 1963

By R. R. Hart, B. C. Wonsiewicz, G. Y. Chin

In recent years there has been increased miniaturization of electromechanical devices to keep pace with current trends toward smaller electronic components. A major problem facing the designer, however, is the higher stresses encountered by the material as a result of shorter springs. Hence an improvement in the elastic limit, as approximated by the 0.01 pct offset yield strength, would be highly desirable. An increase of 25 pct in the yield strength, for example, will permit a 20 pct reduction in both the length and thickness of a cantilever-type spring while maintaining the same compliance. One technique of improving the yield strength that has received little commercial attention is crystal-lographic texture strengthening.1,2 Texture strengthening is expected to be most beneficial in materials of hcp structure, but considerable gain can also be expected in cubic materials. A wire with a (111) fiber texture, for example, is expected to be 20 pct stronger than randomly oriented material, and 50 pct stronger than wire with a (100) fiber texture.293 For sheet specimens with a {110}(112) texture, characteristic of many heavily rolled fcc alloys, the (111) transverse direction is expected to be the maximum yield strength direction, about 20 pct higher than that in the (112) rolling direction.' In addition, the (111) direction is the direction of maximum modulus of elasticity for most cubic alloys. A large value of the elastic modulus could be desirable in designs where stiffer springs are required. To test the above idea, a 0.090 in. (-2.3 mm) thick commercial grade A (5 pct Sn) phosphor bronze sheet, a widely-used material for relay springs, was rolled from the spring-tempered condition (60.5 pct reduction) to various additional reductions up to a total reduction of 95 pct. Subsequently, additional material was obtained with a total thickness reduction of 97.3 pct Standard tensile specimens were prepared from the sheet material with the tensile axis parallel to and at 90 deg to the rolling direction. Tests were run on an Instron testing machine at a strain rate of about 0.050 min-l. Textures were determined by the use of the reflection pole-figure technique. Data were obtained using nickel-filtered CuKa radiation and with the aid of a Siemens pole figure goniometer. The X-ray pole figure studies show an incrzasing development of the texture toward the {110}(112) ideal

Jan 1, 1970

By M. E. Lombardi

THE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 8 ¼ in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling.

Jan 2, 1915

By W. H. Hough, P. B. Leavenworth

Development in the upper Texas Gulf Coast during 1944 resulted in the discovery of 19 new fields as compared with 11 during 1943. These discoveries include 10 oil fields, one dry gas field, and eight gas-condensate fields. Drilling During the year 590 wells were drilled as compared with 418 drilled during 1943. Of these operations, 485 wells were drilled in proven fields, with the following results: 281 oil wells, 22 condensate wells, one dry gas well and 141 dry holes. The remaining 105 wells were wildcats, of which 19 were producers. The geological distribution of these discoveries was as follows: In 1944, production amounted to 178,-522,630 bbl., which was an increase of some 31,670,384 bbl. over the 1943 figure of 136,852,246 bbl. These figures include both condensate and oil production, as separate figures are not available. Wildcatting in the area was more successful during 1944 than in 1943 as the following comparison of number of wells drilled illustrates: Discoveries during 1944 Smith Point, Chambers County.—Standard Oil Company of Texas completed its No. I State, sec. 109, on Feb. 15, 1944, in a Frio sand at 8135 to 8146 ft. The well flowed 250 bbl. of 42º gravity oil through an 1/8-in, choke. Gas-oil ratio was 800 to I; tubing pressure, 1100 bbl. Four other oil wells and one gas well were completed during the year. This discovery does not appear to be of major importance. The producing area lies on the upthrown side of a large fault. North Winnie, Chambers County.—Sun Oil Co. completed No. I P. E. Dougherty on Apr. 27, 1944, from the Frio, through perforations at 8757 to 8759 ft. The initial production was 154 bbl. of 38.3º gravity oil through an 1/8-in. choke. Gas-oil ratio Was 2526 to 1; tubillg Pressure, 2280 1b.; casing Pressure, 1225 lb.; total depth, 9519 ft. Three other wells were drilled during the Year. This discovery is on the downthrown side of the major Winnie Stowell fault, and increases in magnitude the already large producing area along this fault. Mayes Field, Chambers County.—Humble Oil and Refining Company's No. I Mary Etta Mayes was completed on Dec. 24, 1944, in a Frio sand, at 8166 to 8169 ft. through 1/4-in. for 768 bbl. of 40.3º gravity

Jan 1, 1945

By R. J. Linney

Reserve Mining Co. produces 5 million tons of iron ore pellets per year. The finished product runs about 65.50 pct Fe, with 7.75 to 8.00 pct SiO2. Less than 12 pct arrives at the blast furnaces smaller than % in. This plant was originally designed to produce 3.75 tons annually—not 5 million. To handle the increased tonnage a fifth fine crushing line was added, and some very minor changes were made. When production can be stepped up 33 1/3 pct without extensive additions or changes—within the short period of a year—basic engineering has been sound. Operators of the plant consider it the best design job they have seen or heard of, and competent authorities have said that start-up was quicker and easier than for any previous large-scale minerals beneficiation plant. One big advantage is the elbow room allowed. Generally speaking, there is an eternal conflict between operator and designer over space. The designer has his costs per cubic foot, and he is keenly aware that if he permits the number of cubic feet to rise unnecessarily, total costs will be too high. But this was a new operation, and on a large scale. There were no proven standards to go by. Realizing this, Reserve's engineers provided ample and efficient access to machinery, allowing extra space for unanticipated situations. In three years of production this planning has paid off handsomely. Gravity Flow Saves Time and Money: This plant is on a rocky hillside, the car dumper about 270 ft above Lake Superior. In locating buildings and placing machinery the designers mad= good use of gravity flow, at considerable financial savings. In the concentrator building from rod mills to filters, gravity carries the material between all stages of the operation except one—the closed circuit pumping of concentrate between cone classifiers and ball mills. Since no machine is located directly above any other, an observer can stand on the truck ramp adjacent to the offices and laboratory and see practically every phase of activity in the huge building. The first mill section started in August 1955. After a day's run several modifications were made on auxiliary chutes and launders where spillage had occurred. This procedure was followed for the first

Jan 1, 1960

By J. E. Stukel, J. Cocubinsky

A CONSIDERABLE amount of information is available on the equilibrium distribution of manganese between slag and metal under oxidizing conditions. These data have increased our knowledge of the manganese reactions in the open hearth, ladle, and ingot mold. In contrast, there is a paucity of data on the slag-metal distribution of manganese under reducing conditions. The purpose of the present investigation was to study the equilibrium distribution of manganese between blast-furnace type slags and iron saturated with carbon. Experimental Method Furnace: The induction furnace used for the experiments is shown in Fig. 1. A 1 in. pipe, attached to the transite cover, was fitted with a window through which the charge could be observed. Material could be introduced into the furnace through a tee and plug without removing the cover. A graph-it cylinder (3 in. ID and 10'/2 in. long), centered within the induction coil, was used as a heating element. During a test, a zircon plug kept the top of the furnace from becoming too hot from heat radiation. At the bottom, a graphite block on the vertical center line of the furnace and extending 1 1/2 in. into the coil, was used as a support for the graphite crucibles containing the melt. The graphite crucibles, machined from regular carbon electrode stock, had a 2% in. OD with 3/16 in. walls and were 5% in. long. The fumes present in the furnace during the early part of a run made optical readings uncertain. A noble metal thermocouple was, therefore, adopted to measure the temperatures. The arrangement used, shown in Fig. 1, allowed the silmanite protection tube to be replaced with a minimum effort. The thermocouple was calibrated against a standard Pt-Pt-Rh thermocouple in a fused quartz protection tube. The latter was inserted in the molten iron by removing the glass window on the cover. The lower couple was found to be very sensitive to temperature changes. To insure accurate temperature readings, the graphite crucibles were made to fit tightly against the silmanite protection tube. Further, to avoid contamination of the thermocouple by carbon, the silmanite tube was changed and the calibration procedure was repeated at frequent intervals. By using this temperature measuring technique, the furnace was easily held within *1O°C of the desired temperature. Because of the small free space in the furnace, no attempt was made to control the atmosphere. It

Jan 1, 1955

By V. Patarini, D. Kuehl, F. Galasso, M. Salkind

In recent years, a great deal of research has been directed toward the production of continuous low-density, high-strength, high-modulus boron fibers for aerospace applications. A technique which has proven to be quite successful for forming these fibers involves the reaction of boron trichloride and hydrogen on a hot tungsten wire. In this process, a boron fiber is produced which consists of a tungsten boride core covered with amorphous or crystalline boron depending on the temperature of the preparation.2,3 The purpose of this paper is to present the properties which have been obtained to date from measurements and observations on these fibers. Selected samples of boron filament produced by reacting boron trichloride and hydrogen on a 0.5 by 10-3 in. diam tungsten wire substrate using different reacting temperatures were cross-sectioned, polished, and photomicrographed with cross-polarized light. The temperature of the wire was measured using a two-color optical pyrometer. Photomicrographs of these samples are shown in Fig. 1. Three general types of boron, in addition to the tungsten borides, have been identified by means of X-ray powder diffraction techniques: a) at low temperatures (below 1400°C) the boron is deposited in the amorphous form; b) at temperatures between 1400° and 1500°C the boron is deposited in the ß tetragonal form; and, c) above 1500°C the boron is deposited in the B rhom-bohedral form. In the depositing range of 1400" to 1500°C the boron initially deposits as amorphous and becomes crystalline as evidenced by the large equi-axed grains which then merge into columnar grains in later stages of boron deposition. This can be seen in Fig. 1 and has been observed in the X-ray patterns of these fibers, which contain both halos from the amorphous boron and lines from the ß tetragonal form. Above 1500°C the only boron reflections observed in the X-ray patterns were those of the ß rhombohedral form and only columnar grains are seen in the photomicrographs. Photomicrographs of the surface in Fig. 2 show the smooth-surface kernal-type deposition which corresponds to the amorphous form and the rougher surfaces which correspond to the crystalline form. Mechanical measurements were made on amorphous boron produced at 1300°C rather than the crystalline boron because the strengths of these filaments were greater and were more consistent. A tensile tester consisting of a fixed crosshead containing a double

Jan 1, 1967

By Kendall E. Born

Production of crude oil in Tennessee during 1944 was slightly more than 9500 bbl., about 1300 bbl. more than 1943. Approximately 8000 bbl. was produced from the "Mississippi lime" in Scott and Morgan Counties. Some half dozen wells in Clay, Pickett, and Fentress Counties, pumped intermittently, produced about 1500 bbl. This production is from rocks of Ordovician age ranging in depth from less than 500 ft. to approximately 1000 ft. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The production of oil by counties is shown in Table I. Developments There were 20 completions during 1944 totaling 19,615 ft., nearly twice as much as in 1943. One well was drilling on Dec. 31, 1944. Of the 20 completions, one was a small oil well soon abandoned. Three gas wells were completed which are used locally. The completions are listed in Table 2. The distribution of tests according to physiographic divisions is given in Table 3. Cumberland Plateau There were five completions in the northern part of Cumberland Plateau. One was a small gas well in the Cooper pool 3 miles west of Oneida, but an attempt to extend the pool to the south resulted in a dry hole. The most active area in the state during 1944 was the northern Cumherland Plateau, especially in Cumberland, Morgan, and Scott Counties. Several blocks, aggregating more than 500,000 acres, were assembled and leasing was continuing in the early part of 1945. Surface work has been, or is being, carried on by at least four companies. While in an area of past oil and gas production from the "Mississippi lime," the principal interest appears to be in the essentially unexplored pre-Mississippian possibilities. The Knox dolomite group of Cambro-Ordovician age is receiving some attention as a possible reservoir. As the year closed one well was drilling on a surface structure near Lantana, 6 miles southwest of Cross-ville. This test will be drilled into the upper part of the Knox. Late in 1944, it was planned to lay a gas line from northern Morgan County to Oneida in Scott County, a distance of approximately 20 miles. Middle Tennessee Fifteen wells were drilled in Middle Tennessee. In the northeastern Highland Rim area there were 11 completions, one

Jan 1, 1945

By J. R. Campbell

IN order to discuss the subject intelligently, it will be necessary to touch briefly on the forms in which sulphur is supposed to exist in coking coal to be carbonized in beehive or byproduct ovens. Sulphur is known to exist in coal as sulphides and sulphates, as can be determined experimentally. Then there is the so-called organic sulphur, i.e., sulphur in combination with the carbon, hydrogen, and oxygen of the coal, about which much has been written, but nothing definitely proven in an experimental way. In fact, so far as we know, there never has been developed a satisfactory and conclusive method in the laboratory for the direct determination of organic sulphur. For most coking coals, it can be safely assumed that the preponderance of sulphur is in the form of pyrite (FeS2). When exposed to comparatively low temperatures during the coking process, it loses its sulphur according to the following chemical reaction: 7FeS2 = Fe7S8 + 6S. It will be seen, therefore, that six out of the 14 atoms of sulphur (or 42.8 per cent.) are expelled, or volatilized. Fe7S8 remains in the coke as pyrrhotite, or magnetic sulphide of iron; this accounts for the highly magnetic properties of the powdered coke. A more commonly accepted reaction is FeS2 = FeS + S, in which the straight sulphide of iron is produced with 50 per cent. volatilization of sulphur. In the beehive methods of coke making, air is introduced in sufficient amounts to carry on the distilling and the coking processes, and the sulphur is oxidized along with the other volatile products: First, into sulphur dioxide (SO2), known by the pungent and suffocating odoremitted from the trunnel head; second, into sulphuric anhydride (SO3); and, finally, into sulphuric acid, as it comes into contact with the air and moisture. In a properly regulated draft on a beehive oven, there is never complete combustion of the gases. In other words, the coking process should be carried on in a reducing atmosphere, and a low-grade producer gas kept issuing from the trunnel head. For coals of about 30 per cent. volatile matter, the ratio of air to gas is 3 ½ to 1. In complete combustion, the ratio is 6 to 1, producing an extremely high temperature

Jan 1, 1916

By M. E. Straumanis, R. P. Shodhan

LATTICE parameters of molybdenum of various purities are summarized in Table I. The latter shows that the parameter fluctuates between 3.1467 and 3.1475A. The room-temperature expansion coefficient a is also not well-known as values from 4.90 to 5.20 x 10-6 can be found in the literature.=-' It, therefore, seemed appropriate to repeat the measurements under exactly controlled conditions, using high-purity Hilger molybdenum powder (containing 0.0015 wt pct of Fe, 0.005 of Si and traces of other elements) and a 99.95 pct pure Sylvania Electric preparation (containing Cr, Fe, Ni, Si, Sn, and C in amounts of 50 ppm of each and in still smaller amounts Cu, Pb, Mg, and Mn). Of course, both samples could have contained at least 0.01 pct of oxygen in form of a surface oxide. However, oxygen, because of its small solubility in molybdenum, does not influence its lattice constant.g The determinations were made in a cylindrical precision X-ray camera, 64 mm in diam, the temperature of which was controlled within *0.05"C, by inserting it into a special thermostat." To exclude the film shrinkage effect (after the development of the film), the asymmetric film placement method was used." Absorption corrections (e.g., by extrapolation)" were unnecessary because of the use of a thin Li-B-glass fiber (about 0.08 mm in diam) which was fastened to the sample holder of the camera and dusted with the fine molybdenum powder. Cum radiation of the wavelength 1.389350 kX was applied because it produced in 30 min the line (420) having a high Bragg angle of about 81.6 deg. The conversion factor of 1.00202 gave the results in angstroms. To obtain the expansion coefficient a, exposures were made at various temperatures t, see Fig. 1, on at least two films at each temperature. The films were measured with a componator and the lattice constants a were calculated. The expansion coefficient was found from: where a2s is the constant at 25°C and A is the change in a and t. The same equation (knowing a) was used to reduce all the constants obtained at various temperatures to that of 25"C, Table 11. The probable error S507p (at a 50 pct confidence limit) was calculated from the reduced constants:

Jan 1, 1969

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporation Law of the State of New York ; its corporate name is AMERICAN INSTITUTE OF MINING ENGINEERS; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely (1) Members ; (2) Honorary Members , (3) Associates , and (4) Honorary Associates Only Members and Associates residing within the United States of America, Republic of Mexico and Dominion of Canada shall be entitled to vote at the meetings of the Institute. SEC. 2 All Members, Honorary Members, Associates and Honorary Associates of the American Institute of Mining Engineers as the same existed on the day of the incorporation of this Institute, are Members, Honorary Members, Associates and Honorary Associates, respectively, of this Corporation SEC. 3. The following classes of persons shall be eligible for membership in the Institute, namely, as Members and Honorary Members, all professional mining engineers, geologists, metallurgists or chemists, and all persons practically engaged in mining, metallurgy or metallurgical engineering ; as Associates and Honorary Associates, all persons desirous of being connected with the Institute who, in the opinion of the Council, are suitable. SEC 4. Every candidate for election as a Member or Associate of the Institute must be proposed for election by at least three Members or Associates; must be approved by the Committee on Membership, as prescribed in the By-Laws ; and .must be elected by the Council. Not less than three-fourths of the votes cast shall be necessary to an election Every person so elected shall become a Member or Associate, as the case may be, upon payment of his first dues as herein-after prescribed Each candidate for Honorary Member or Honorary Associate, must be recommended by at least ten Members or Associates ; must be approved by the Council ; and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of all the Directors present ; provided, however, that the number of Honorary Members and Honorary Associates shall not at any time exceed twenty SEC. 5. If any person elected a Member or Associate does not, within sixty days after notice of his election, accept the same and pay his initiation fee and dues for the current year, his election may be cancelled at the discretion of the Council.

Jan 1, 1917

By D. A. Lyon

Discussion of the paper of DORSEY A. LYON and ROBERT M. KEENEY, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1707 to 1730. LAWRENCE ADDICKS, Douglas, Ariz.-I think papers of this character, while general in, nature, are of particular value and interest, because when we figure on competing with the East in electrometallurgical industries, on account of the cheap power on the Pacific Coast, we have to take two or three things into account. In the first place, power very rarely amounts to more than 20 per cent. of the total cost of an operation, even .though it be electrometallurgical, and I think it is the common opinion among those who are not familiar with those particular industries, that it amounts to more than 50 or 60 per cent. Take copper refining; we may say that it is 15 per cent. of the total cost. In the second place, around New York City, with 100 per cent. load factor and a reasonably large load, say 10,000 kw., we can generate from a certain class of coal 1 kw.-hr. for about 0.3c. I might say, however, that 0.3c. does not include overhead charges, interest on the investment, etc. The third factor we have to consider out here is that any product to be salable, must command a retail market. It would be useless to produce wire bars here on the Pacific Coast because there is no place to roll them. If we were going to establish a copper refinery, that part of its output which goes into wire bars would have to be taken care of by building a rolling mill alongside of it to turn it into wire and finally make a product that is salable. I do not think, however, that Mr. Lyon need have excluded copper refining from his industries. There are perhaps 50,000,000 lb. of copper a month refined in this country on a custom basis. I think the smelting companies would be very glad to build refineries here if conditions warranted it. The recent extensions of the Great Falls refinery and of the Tacoma refinery in the last few months give evidence of that.

Jan 12, 1915

By Francis Foley

WITH the possible exception of high-speed tool steel, the service demanded of rock-drill steel is probably more precarious than that of any other tool steel. Unaided by the helpful influence of alloys and dependent solely on the efficiency of the heat treatment applied for its ability to stand up under the abuse to which it is necessarily subjected, rock-drill steel is worthy of intensive study. For its heat treatment the smith has his fire, an oil fire perhaps, and a quenching bath; he judges' the temperature by his eye. There are shops where excellent drills are produced by this method, but there are more where the product varies between very good and very bad. Pyrometers with specially designed equipment are used in but few cases. But the responsibility for rock-drill failures does not rest entirely on the smith. Little has been published concerning the efficiency of drill steel, though the Canadian Mining Journal' published the breakage record of a large number of hollow drill steels. This record indicates that most of the breaks occur during the early life of the steel and that as a given batch of steel is used, its percentage of breakage decreases. This fact, the article points out, is at variance with the much-talked-f theory concerning failure from crystallization and fatigue. It seems to point to the fact that the greater part of drill-steel failure from breakage is traceable to faulty manufacture, resulting in defects in the bore of the hollow steel from inclusions of slag or oxides, etc. As this defective material meets with early failure, it is weeded out. In addition, some breakage may be caused by a lack of proper condition with respect to heat treatment of the steel as furnished by the manufacturer. In the article mentioned, the breakage of 1 ¼ -in. (3.17 cm.) hollow steel is given as 4.62 per cent. for the early period of use, with a decrease to 3.35 per cent. and 2.67 per cent. With time in use. For 1-in. (2.5 cm.) hexagonal hollow steel, the figures for breakage are 0.18 per cent. and 0.06 per cent.; attention is called to the "enormous decrease in breakage by the use of smaller diameter drills." The figures are given as so many "drills sharpened," but there is no way of determining the percentage of

Jan 6, 1921

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporation Law of the State of New York ; its corporate name is AMERICAN INSTITUTE OF MINING ENGINEERS; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely (1) Members ; (2) Honorary Members , (3) Associates , and (4) Honorary Associates Only Members and Associates residing within the United States of America, Republic of Mexico and Dominion of Canada shall be entitled to vote at the meetings of the Institute. SEC. 2 All Members, Honorary Members, Associates and Honorary Associates of the American Institute of Mining Engineers as the same existed on the day of the incorporation of this Institute, are Members, Honorary Members, Associates and Honorary Associates, respectively, of this Corporation SEC. 3. The following classes of persons shall be eligible for membership in the Institute, namely, as Members and Honorary Members, all professional mining engineers, geologists, metallurgists or chemists, and all persons practically engaged in mining, metallurgy or metallurgical engineering ; as Associates and Honorary Associates, all persons desirous of being connected with the Institute who, in the opinion of the Council, are suitable. SEC 4. Every candidate for election as a Member or Associate of the Institute must be proposed for election by at least three Members or Associates; must be approved by the Committee on Membership, as prescribed in the By-Laws ; and .must be elected by the Council. Not less than three-fourths of the votes cast shall be necessary to an election Every person so elected shall become a Member or Associate, as the case may be, upon payment of his first dues as herein-after prescribed Each candidate for Honorary Member or Honorary Associate, must be recommended by at least ten Members or Associates ; must be approved by the Council ; and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of all the Directors present ; provided, however, that the number of Honorary Members and Honorary Associates shall not at any time exceed twenty SEC. 5. If any person elected a Member or Associate does not, within sixty days after notice of his election, accept the same and pay his initiation fee and dues for the current year, his election may be cancelled at the discretion of the Council.

Jan 1, 1910

By Nicholas J. Palethorpe

BACKGROUND Before addressing the above topic in any detail, it is pertinent to provide some background on Australia for those people who have not been there or who have a limited knowledge of our continent. Australia is approximately the size of the continental U.S.A. (excluding Alaska) covering an area of approximately 7 million square kilometres. It has a very dry climate which has led to a concentration of people in major cities scattered around the continents perimeter. Australia's population is currently approximately 15 million. Of the work force of 6.3 million, 72% work in tertiary industries, 20.2% in manufacture, 6.5% in agriculture and 1.3% in mining. Agriculture accounts for 46% of exports, mining for 31% and manufacturing for 23,. Economic activity is based on:- Agriculture This is capital intensive and covers extensive areas and is reliant on low cost farming. A.range of foods and fibres are produced with over 70% of production being exported. Such products are of course subject to the usual vagaries of world market demand and market access, particularly in regard to the operation of trade blocks such as the E.E.C. Mineral Resources A wide range of minerals and an abundance of iron ore, coal, gas and uranium resources provide an increasing volume of exports. However, Autralia's oil resources at present only supply approximately 70% of local requirements. Industry This is diverse and encompasses the processing of agricultural products and mineral ores as well as helping to supply the consumer and capital goods needs of the whole community. However, the small scale of local markets, the geographic isolation of Australia and relatively high wage costs have limited the scale of Australia's industry. Advanced technology has overcome some of these difficulties and high tariff and import quotas protect local producers from the full force of international competition. In 1980/81 Australia's Gross Domestic Product amounted to $130 billion with approximately 24% of this being devoted to investment. In the past decade Australia has experienced inflation rates ranging from 5% to 17% and only modest real growth rates ranging from 0.4% to 5% per annum. We have also experienced, as have many other industrialised nations, continuing wage and price increases. Unemployment presently stands at 6%. MINERAL DEVELOPMENT As the above figures indicate, Australia's continuing prosperity is very dependent on the mineral and agricultrual sectors of our economy. The dependence on these sectors is highlighted by the table below which indicates our position in a global context. [Australian Production of Minerals in a World Context Western World % Total Western World Position Mineral Production 1980 1st Rutile 75 Ilmenite 31 Zircon 70 Bauxite 36 Iron Ore 11 Tungsten 14 2nd Lead (Conc.) 15 3rd Manganese Ore 14 Brown Coal 11 (1979) Zinc (Conc.) 10 4thSilver (Conc.) 10 Nickel 6 5th Tin (Conc.) 5 6th Black Coal 5 Gold 2 Source: Mining Annual Review 1981] The total value of all mineral and fuel exports in 1980/81 is estimated at $5.9 billion. This prominence in the world mineral production has largely been achieved in the last 15 - 20 years. In fact, in the early 1960's, Australia had only 2 major mining export centres, Broken Hill in New South Wales and Mt. Isa in Queensland. This growth is highlighted by the fact that in 1963, for example, we exported only 9 tonnes of iron ore and less than 4 million tonnes of coal. In 1980/81 we exported 75m. tonnes ',of iron ore (valued at $1,117m.) and 47m. tonnes of coal valued at $1,965m.). The growth in our mineral industry has come about because of a number of factors. Abundance of Mineral Resources We are particularly well endowed with mineral resources, as indicated below.

Jan 1, 1982

By T. S. Spice, H. L. Lovell, R. W. Utley

With the increased demand for lightweight aggregate, such materials have been manufactured from slags, clays, slates and, to a minor extent, the refuse of coal preparation processes. The latter source is attractive due to current interest in eliminating air pollution and improving the unsightly appearance of refuse piles as well as potential economic advantages, if a satisfactory product can be manufactured. A study has been made relating the composition of coal refuse, expressed as washability data, and the properties of a resulting aggregate. Three different refuse samples (bituminous and anthracite) were separated at gravities ranging from 1.4 to 2.96. Their chemical composition was determined. Aggregates were prepared in the laboratory from these fractions before and after ashing, at temperatures between 1250' and 1350°C. The specific gravity, expansion and compressive strength of the products were measured. The response of the refuse to bloat is related to the chemical composition of the ash to yield a glass of desirable viscosity and to the presence of a material which will form a gas in the appropriate temperature range. Carbonaceous material within the particle is a negative factor since after the glassy phase forms, oxygen cannot enter the mass thus inhibiting bloating. Precombustion of the refuse is also detrimental since it removes substances of gas-forming capability. The fraction sinking at 2.60 yielded an aggregate which had the lowest specific gravity, greatest expansion and greatest compressive strength. The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data and factors affecting the production of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsyl- vania State University to study the possible elimination of air pollution from coal refuse fires by producing a low-carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product. It was hoped that these studies would assist in the design of a process and in establishing the optimum specific gravities at which refuse separation could be made in respect to the production of a low grade fuel from the float product and a raw material for lightweight aggregate from the sink product. The combination of producing a saleable low grade fuel and a lightweight aggregate, while at the same time minimizing disposal costs and air pollution contributions would be attractive to the coal mining industry. MECHANISM OF BLOATING Austin, Nunes and Sullivan,1 Ehlers,3 Everhart, 4 Riley7 and others, have stated that bloating is an expansion process in which two essential conditions exist simultaneously. These are: the development of a glassy phase over a relatively wide temperature range (the viscosity of this glassy phase plays a major role in the retention of the evolved gases) and the evolution of gases (SO2, SO3, CO2 and O2) from mineral decomposition in sufficient quantities at appropriate temperatures to form a cellular structure in the mass. Unless these two "type" reactions take place at the same time or in overlapping ranges of time and temperature, cellulation will not occur. In this event, the gas will escape or the melt will be too fluid to retain it; or if retained, the cells may be too large or the walls too thin for good strength in the product. The stages that occur when clays and shales are heated in an oxidizing atmosphere may be summarized as follows: 1) Drying and removal of free water to 200°C. 2) Absorbed water dehydration period (200 to 480°C). 3) Chemically-combined water dehydration period (480 to 700°C).

Jan 1, 1965