Search Documents

By Robert Maddin

THE application of electrolytic polishing of metals introduced a new technique for preparing surfaces, especially for single crystals. This procedure has generally been assumed to eliminate the strain introduced by mechanical polishing and to result in a more truly representative surface, particularly in the case of soft metallic materials. However, apparently little information is available concerning specific characteristics of a surface prepared electrolytically. The conventional method of mechanical polishing is known to produce a layer of distorted metal which is usually removed by a suitable chemical etchant. To what depth the strain introduced by mechanical polishing penetrates into the lattice is still obscure. The present investigation illustrates the apparently anomalous appearances of glide ellipses on electrolytically polished surfaces of aluminum single crystals. EXPERIMENTAL PROCEDURE AND RESULTS Aluminum single crystals, 99.975 pct pure, remaining from the investigation of Found,1 were polished electrolytically using a solution of fluoboric acid and a low current density. Laue back-reflection technique, interpreted after the manner of Greninger,2 was used to determine the orientation and the specimen axis rotation of the crystals. Three flat surfaces about 4 mm wide parallel to the specimen axis, one perpendicular to the theoretical slip direction and the other two 1200 apart, were polished mechanically and repolished electrolytically. A tensile load was applied using a Southwark-Emery tensile machine at a rate of about 40 lb per min. Elongation was measured by noting the initial and final gauge lengths. X ray diffraction was used to obtain the usual X and X values in order to calculate the elongation and shear by plotting stereographically the specimen axis rotation by means of the Schmid-Boas formula.3 In Table I may be found the value of the gauge diameter, measured elongation, calculated elongation and shear for the crystals investigated. Fig 1 shows the initial and final positions of the specimen axes of the crystals. [ ] At a low magnification the slip lines developed on specimen Al-I appeared straight and rather evenly spaced. However, at a high magnification, the slip lines were seen to be composed of small markings which were present throughout the length of the specimen (Fig 2). The distance between the markings was fairly constant and their directions all parallel to one another. Fig 3-5, photographed on different surfaces of the specimen, illustrate the interesting appearance of these lines. It may be noticed from Fig 4 that the markings, which present the appearance of

Jan 1, 1948

By Louis A. Carapella, Ralph Hultgren

WHEN F. Heusler1 found in 1898 that certain alloys containing only copper, manganese, and tin were ferromagnetic, the discovery excited a great deal of interest and led to numerous investigations. It was early found that tin could be replaced by aluminum, arsenic, antimony, bismuth, or boron without destroying the ferromagnetic nature of the alloys.2 Copper may also be replaced by silver.3 All these alloys have come to be known as "Heusler alloys." The aluminum alloys apparently were the most magnetic and have been most extensively investigated. However, no agreement has yet been reached as to the source of the ferromagnetism arising from these nonferromagnetic elements. Absence of reliable quantitative data makes speculation hazardous. The value of much of the earlier work was vitiated by lack of necessary precautions against contamination, and by lack of close control of heat-treatment. It was only recently established that in aluminum Heusler alloys" the ferromagnetism arose from a single phase, an ordered body-centered-cubic structure. With modern methods of preparation, heat-treatment, and X-ray examination, it is possible to prepare these alloys without contamination, to heat-treat them intelligently, and to determine what phase or phases are present in the finished sample. In the present investigation, a series of pure alloys in the comparatively neglected copper-manganese-tin system have been prepared, which consist of a single, body-centered-cubic structure (the beta phase) and whose compositions vary within wide limits. The magnetic saturation values of these single-phase alloys have been quantitatively determined, so that considerable data on the effect of composition on the ferromagnetism have been made available. In the course of the investigation some information on the extent of the stability of the beta phase and the nature of phases in adjacent regions of the ternary diagram has been accumulated. Anomalies in earlier data have been explained, and alloys have been prepared that are much more strongly magnetic than any previous Heusler alloys. PREVIOUS WORK In the original work of F. Heusler1 and coworkers,2 a maximum magnetic saturation value of I = 107 was found at the composition Cu6Mn3Sn, while a value for Cu2MnA1 of I = 443 was early measured. Ross and Grays found a second maximum at the composition Cu2MnSn, which was much more magnetic than Heusler's original alloy. F. Heusler6 then reinvestigated the system, confirmed their results,

Jan 1, 1941

By E. C. Truesdale, W. K. Waring

The Research,Division of The New Jersey Zinc Company (of Pa.) has conducted, over a period of years, numerous tests of the reducibility of various zinc ores and the reactivity of various kids of coal, using a number of different experimental methods. Most of these tests have involved the reduction of mixtures of ore and coal. In such cases the following simultaneous reactions are believed to be mainly responsible for the production of zinc, as was shown by Bodenstein' some years ago: ZnO + CO = Zn + CO2 [i] C + COj = 2CO [2] Each of these reactions is dependent upon the other for the supply of CO and COz, respectively, and the over-all rate of formation of zinc vapor will be determined by the slower of these two reactions. An analogous pair of reactions sometimes of importance is: ZnO + He = Zn + HZO 13] C + Hz0 = CO + He U3 While it is possible to obtain an indication of the relative reducibility of various ores, or of a fine versus a coarse Ore, by testing them with a given coal, and while coal reactivities may be measured in a corresponding manner, a more direct determination of relative reaction rates is possible by carrying out the desired reactions, such as I and 2, separately and under reproducible conditions. It is one purpose of this paper to present some of the results that have been obtained by the latter method. C. G. Maier2 discusses the relative rates of reactions I and 2 and concludes that while at relatively low temperatures reaction I is faster than reaction 2, this difference becomes less with increasing temperatures, although at smelting temperatures reaction is still the faster. He also says (p. 48), "At temperatures . . . be- -tween 1100' and 1300°C., . . . the zinc oxide reduction reaction is intrinsically more rapid than its physical limitations; that is, it is limited by gas diffusion rates.'' In the course of numerous reactivity tests involving the separate use of reactions and I and 2, we have obtained data that show by direct experiment, we believe for the first time, the correctness of Maier's statements concerning these reactions. We also include data on the relative rate of reaction 3, involving reduction by hydrogen. Finally, some interesting results obtained by carrying out the reduction of ' a zinc ore-coal briquet in streaming atmospheres of nitrogen, carbon monoxide and hydrogen, respectively, are presented.*

Jan 1, 1944

By Frank S. Gardner, Morris Cohen, Dara P. Anita

There is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a suecimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallo-graphic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X - ray exposure and film - development conditions, a standard reference line is Superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By Morris Cohen, Dara P. Anita, Frank S. Gardner

There is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a suecimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallo-graphic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X - ray exposure and film - development conditions, a standard reference line is Superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By C. V. Millikan

New developments in air-gas lift practices in the Mid-Continent area since our Pall meeting in Fort Worth have done much to increase the efficiency of installations, and thus bring within economic limit of air-gas lift many wells which could not have been flowed profitably before. After the gas-lift had so thoroughly demonstrated its value in the Seminole field, its use spread to other areas and many installations were made of which the economy could be questioned. In the Seminole area, when production began to decline it was necessary either to increase the efficiency of the air or gas-lift or to put the wells on the pump, and pumping was not a process of lifting oil to which any operator looked forward with confidence. These conditions have resulted in the development of many practices which increase the efficiency and permit wells to be flowed with air or gas which earlier could not have been flowed economically, and wells which have been flowing to continue to a lower rate of production. The practices which have come into more common usage in the Mid-Continent area recently are mostly revivals of and improvements on practices which have been known in air-lift work for several years. Many arc peculiar to the individual well on which they are used. Intermittent Flowing Some interesting results are being obtained in Seminole and other districts by intermittent injection of gas. Gas is introduced during per-iods iods of 3 to 5 min. at a rate considerably over that necessary to acquire the production at a steady rate of injection, and is then cut off for a period of 3 to 15 min. Two to five wells are run from the same group of conlpressors. The total volume of gas required is sometimes reduced as much as one-third of that required when it is introduced at a constant rate, without changing the amount of oil production. The maximum pressure required is usually higher, but the average equal to or lower than that required for constant rate of flow. The effect on the wells is usually an irregular rate of flowing which may cause inconvenience where recycling is practiced. It would seem that this increase in efficiency is due to less slippage when the gas is introduced intermittently than when it is intro-

Jan 1, 1928

By Leslie G. McMillion

A field project to develop and demonstrate a method for alleviating problems of highly mineralized ground water where they occur as isolated zones or pockets in fresh-water aquifers is being conducted in the Ogallala aquifer of eastern New Mexico by the Robert S. Kerr Water Research Center. Removal of contaminated water is by a large-capacity well and the pumped poor-quality water is used locally for secondary recovery of oil. Benefits of the operation are threefold in that the aquifer is being reclaimed for future fresh-water production, contaminated water is being used beneficially, and fresh water which otherwise would have been used for waterflooding is available for other purposes. Ground-water quality in the site has improved markedly after two years of operation. Use of water in the arid and semiarid Southwest has grown so rapidly that demands in many localities far exceed available supplies. In the High Plains region of New Mexico, Oklahoma, and Texas, the only large sources of water are underground reservoirs, being depleted at an alarming rate. In some parts of this region, the aquifers contain pockets of highly mineralized waters; and the mineralized waters in some of them have started spreading in response to the drawdown effects of pumping wells. The aquifers of this region are primarily composed of sand and gravel beds; any cleanup by natural processes will require many tens or even hundreds of years. Most of these pockets of highly mineralized water were caused by oil-field brines seeping downward from earthen disposal pits. Thousands of these pits were in use in the region until only a few years ago when they were prohibited by the oil regulatory agencies of the respective states. The resulting areas of poor quality water are serious enough to warrant much corrective attention. Correction will involve one or more of three approaches: 1) Restrict the pumping of fresh water in the zones where the drawdown of the pumping well will significantly influence the movement of the contaminant. 2) Remove the highly mineralized water entirely from the affected area. 3) Develop and pump the poor-quality water in such a manner that its movement is held in check, even though only a part of the contaminant is actually removed. The principal hurdle to overcome in applying methods 2 or 3 is financing of the operations, since there are very

Jan 1, 1972

By S. Stutz

Three years ago, at the Philadelphia meeting, in February, 1881, the author had the pleasure of presenting to the Institute a paper on coal-washing machinery.* Since that time many new machines, with important improvements and labor-saving apparatus, have been introduced, the construction and description of which may be of interest to some of the members of the Institute. By referring to the above-mentioned paper, and more especially to Plate IV., representing a vertical section of a coal-washer, it will be noticed that the bottom of the plunger-box B is made level or horizontal, and supports a spring-buffer F for the purpose of limiting the down-stroke of the plunger P and receiving the impacts of the latter. Althongh the construction of the box, in view of these impacts, received from the start the proper attention (the bottom of the chamber 3 being made of three thicknesses of 3-inch planks, resting on 6-inch sqnare columns), yet, through careless working of the machinery, without the necessary water in the box, it proved in several instances not strong enough, and had to be changed. To prevent such interruptions in future, it became necessary to devise some means for relieving the machine from the impacts of the plunger altogether. This has been accomplished by the arrangement shown upon Plate I. of this paper, representing a new waesher; and not only has the difficulty been overcome, but also sorne other advantages have been obtained, as will be seen further on. The compartments +, A' of the separator-box have been set upon heavy cast-iron brackets B, leaving sufficient space below the bottom for the buffer F and the sediment-valve K. By means of the plunger-rod 6 passing through the stuffing-box s to the outside, and provided at its lower end with a shoe a, the impacts of the plunger are now transmitted from the buffer F directly to the foundation. At the same time a better guide for the plunger P in its up and down movement has been obtained. The plunger of the former machine had only the guide I and the yoke Y, whereas the new machine has an additional guide in the stuffing-box s, thus preventing wear and friction of the plunger against the lining of the box. Further-

Jan 1, 1884

By J. C. Motz

Introduction The variations in crushing plant design seen during the past 30 years provide a valuable source of information and experience from which one can select the optimum arrangement for a specific requirement. The purpose of this paper is to examine some specific equipment configurations as they relate to operating efficiency, plant availability and final product size in the form of mill feed. Due to the varied ore properties, physical space limitations, size of ore body and financial resources, there is no single crushing or grinding flowsheet that is best. Since energy costs have risen dramatically during the recent past, it became obvious that significant savings are possible by selecting equipment and a circuit which offers low power requirements balanced with low wear metal and installed equipment costs. Relatively clear and measurable are the metal and maintenance costs and the ever increasing cost of energy. Metal costs in the form of crusher liners have not quite doubled in the last 20 years, while power costs have increased by a factor of four or five, depending on the region considered. Estimates made only a few years ago on the increased cost of energy are obsolete in view of the recent unstable conditions. Since power is therefore becoming the largest cost area, it behooves us to investigate potential cost saving methods in the form of lowering the KWH/Ton of crude. Crushing To reduce run-of-mine to mill feed requires reduction in a series of stages. The physical size and power requirements of a crusher capable of reducing hard rock vary depending on the application. Extended experience in most crushing plants show that a minus 19MM (3/4 in.) rod mill feed can be and is being produced in three stages of crushing. In the majority of cases, the last crushing stage is closed circuited using anywhere from 19MM (3/4 in.) to 14MM (9/16 in.) slotted openings on the sizing deck. In some copper concentrators, the mill feed is all passing 13MM (1/2 in.) using three stages of crushing and 14MM (9/16 in.) square openings on the closed circuit screens. It was felt by some that crushing to this fine size is only possible if the ore is friable and is relatively soft in comparison to the harder ores. Our results show that some of the copper ores are as hard as taconite and are crush-

Jan 1, 1982

By Dara P. Antia, Morris Cohen, Frank S. Gardner

THERE is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a specimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallographic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X-ray exposure and film-development conditions, a standard reference line is superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By C. R. Fulton

The idea of making permanent magnets by sintering is not a new one, but until the introduction of the iron-nickel-aluminum permanent-magnet alloys there was little need for such a process. Permanent-magnet alloys in use up to the time of this development could be forged and machined to the exact size or shape required without too much difficulty. These new Fe-Ni-A1 alloys, which have become known as Alnico in this country, soon became very popular because of their superior magnetic properties, but when they were made by casting they did have some disadvantages when compared with the older type of permanent-magnet steels. Among these disadvantages were the following: 1. It was almost essential that they be cast to size, since they could not be readily forged or machined. The material could be ground but this was quite expensive, particularly for small magnets in large quantities. 2. The material had a large grain size and was mechanically weak. 3. Close tolerances could not be held and on small magnets this meant grinding almost the entire magnet. Because of the brittle nature of the material, there was considerable loss due to chipping and cracking during these grinding operations. 4. Because of its high aluminum content, the molten alloy had a high surface tension. It was difficult to prevent loss of aluminum by oxidation during the melting operation. In view of these difficulties it is not hard to understand why a process for sintering alnico was developed, or why sintered alnico has come into such widespread use in recent years. It might be well to qualify this by saying that it has come into widespread use for small magnets weighing 2 oz. and less, of the type shown on Fig. I. In this size range, sintered alnico has been able to compete in price with cast alnico. Magnets larger in size, of the type shown on Fig. 2, can be made but they do not compare favorably in price with the cast material. An idea of the range of sizes that have been produced is given by Fig. 3, which shows a small magnet weighing 0.006 oz. and a large magnet with a steel insert weighing 4 lb., both made from sintered alnico. Magnets weighing more than 2 oz., however, should not be made from sintered

Jan 1, 1945

Before hostilities between the colonies and Great Britain began in 1775, most of the coal used in the northern colonies undoubtedly came from England, with some supplies for New England coming from Nova Scotia; in New York and Philadelphia the supply came from England with some from the Virginia mines. Table 4 shows data obtained from the Public Records Office, London, for the years 1768-1772. This table supplements Table 3, which records only a few shipments from Richmond in 1768 and 1769; as there was no coal shown in imports coastwise in 1769 in Table 4, and only two small shipments in 1769 in Table 3, there may have been a cessation of shipments then, for some reason not now known. In Table 5 are incorporated all the data in the first two, with a few earlier years, and an attempt is made to estimate the amount used during the period by allowing for coal exported. With the small total tonnages a carryover from one year to another makes a large difference in the annual figures, but over the period the result may be fairly indicative of the amount of coal used before the Revolution. According to present day ideas the quantity of coal used during that war was very small, but apparently it was badly needed for the manufacture of the small amount of munitions made in those troublous days. As Philadelphia was the leading city along the Atlantic coast, and as the southeastern part of Pennsylvania was the leader in making iron, as well as making rifles, it is natural that the first call for coal came from there. At first, procuring supplies such as coal, powder and sulphur was handled by a Committee of Safety, which later became a Council of Safety and later this committee's functions were turned over to a Board of War, functioning with the military organization of the colony. . The organizations of the several colonies were slightly different, but Pennsylvania, Maryland and Virginia followed this scheme generally. Later in the war the Congress began to make arms for the troops, and it is difficult now, with the few records available, to tell when the state functions ceased and those of Congress began. On December 5th, 1775, the Committee of Safety

Jan 1, 1942

By Lewis A. Riley

I desire to submit, for the consideration and information of the members of the Institute, the following data, drawings, and tables, showing what I believe will be interesting information with regard to the diamond drill, and its uses in developing mineral lands. I would first say that the results given have been obtained during the past two years by means of two drilling machines belonging to the Lehigh Valley Coal Company, operating on their coal lands in the Mahanoy, Lehigh, and Wyoming regions. 1st. A tabulated statement, giving location of borings, date, progress, total cost, itemized cost per foot, etc. 2d. Section showing strata bored in Nos. 5 and 10 holes at Mt. Carmel, see Plate VI. 3d. Section showing strata bored in No. 19 hole at Hazleton, see Plate VI. 4th. Photograph and description of drill No. 2. From the first it will be seen that the total number of test-holes bored up to May 1st of this year is 24; 9 of these are in the Mahanoy region, 6 in the Lehigh region, and 10 in the Wyoming region, in all of which cores have been taken for the whole distance. The total distance bored is 9902 feet. The majority of the holes have been put down for the purpose of proving the lower veins of the coal series, and have had to encounter the harder rocks of the coal formation. Much of the distance has been through the lower conglomerates, going in some cases through the coarse egg conglomerate, the foundation of the coal deposit, and to the green sandstone and red shale which underlie it. These lower sandrocks and conglomerates are among the hardest known to geologists, and present a formidable resistance to the exploring drill. This fact must be taken into consideratiotl in comparisons of cost of drilling, and when considered will still further improve the very favorable results I am able to show in my statement of costs. In illustration, I will cite the work of one bit when boring in the upper or softer rocks of the Wyoming region, where 280 feet were obtained without resetting, while in the Lehigh and Mahanoy regions, in the lower and harder rocks, bits set with the same quality of diamonds would only bore from 3 to 20 feet before being worn out. In this connection it may

By E. L. Estabrook

THE production of crude oil in Wyoming rose to 44,290,010 bbl. in 1923 and declined, during 1924, to 39,295,030 bbl., a decrease of about 11 per cent. The Salt Creek field supplies 75 to 80 per cent. of the production. Pipeline runs from the Salt Creek field reached a maximum in November, 1923, at a daily average for the month of 116,437 barrels. During 1924, the gas pressure in Salt Creek has declined rapidly and the production dropped to about 60,000 bbl. per day. Part of 'the decline during the last few months was due to lack of power to pump the wells. The electric-power plant of the Midwest Refining Co. did not begin to deliver current until the middle of December, by which time several hundred wells were off production. The cold snap in December, which brought, the temperature down to 30° below zero on the 17th, tied up operations almost completely and the average production for the month was only 49,545 barrels. As more wells are being pumped and the number of dead wells reduced, the production is rising and was up to 61,000 bbl. during the last week of January. A further increase is expected as the weather becomes warmer. The production of Salt Creek, by months, during 1924 is given in Table 1. TABLE 1.-Total Monthly Production, Average Daily Production and Number of Producing Wells in Salt Creek during 1924 TOTAL PRODUCTION, DAILY AVERAGE, NUMBER OF MONTH BARRELS BARRELS WELLS January 3,523,647.40 113,666.05 919 February 3,074,916.67 106,031.61 929 March 2,977,095.14 96,035.32 950 April 2,811,110.22 93,703.67 987 May 2,858,842.04 92,220.71 1,024 June 2,649,752.57 88,325,09 1,092 July : 2,697,829.36 87,026.75 1,153 August 2,624,371.84 84,657.15 1,213 September 2,281,219.04 76,040.64 1,274 October 2,073,961.42 67,000.84 1,313 November 1,722,050.09 57,401.67 ~ 1,335 December 1,535,903.78 49,545.28 1,352 Total 30,831,699.57 84,239.61 1,352

Jan 3, 1925

By M. H. Richman, L. M. Markowitz

MUCH of the available information on which the heat treatments of a particular steel are based is found in the isothermal-transformation diagram. Such is the case despite the fact that the usual thermal treatments involve continuous transformations, i.e., transformations which occur on cooling, rather than isothermal transformations. This rather unusual practice is continued because of the abundance of published isothermal-transformation diagrams1, 2 which are relatively easy to determine experimentally as compared to continuous-transformation diagrams.3, 4 However, this can easily lead to the production of improper micro-structures and may not allow full advantage to be taken of the inherent hardenability of a steel. A mathematical method of estimating the continuous-transformation diagram from the available isothermal data was developed by Grange and Kiefer;5 but, due to the mathematical approximations required in the calculations, the computation of continuous-transformation diagrams has been limited to individual cases and no large-scale compilation of these diagrams is available. With the present availability of high-speed digital computers, the problem of time-consuming approximations may be minimized and continuous-transformation diagrams may be constructed with the insertion of isothermal data into a basic program. It is the purpose of this report to announce the availability of such a program and compare the computed and experimental continuous-transformation diagrams for two different steels. Let us first review the method of Grange and Kiefer5 and then compare the results of the machine calculations with the experimentally determined diagrams. In order to apply this method, one requires the isothermal-transformation diagram and a set of curves representing cooling at constant rates. A section of an isothermal-transformation diagram is shown in Fig. 1 together with a cooling curve of M0F per sec. The cooling curve is constructed to start from the A1 (eutectoid) temperature if the transformation product is the eutectoid microconstituent (i.e., pearlite or bainite), from the A3 temperature if the product is primary ferrite, or from the 4, if it is proeutec-toid cementite. The cooling curve in Fig. 1 intersects the curve representing the start of isothermal transformation at a point A' corresponding to a temperature TX and a time fX. An arbitrary lower temperature To (on the

Jan 1, 1968

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporation Law of the State of New York ; its corporate name is AMERICAN INSTITUTE OF MINING ENGINEERS; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely (1) Members ; (2) Honorary Members , (3) Associates , and (4) Honorary Associates Only Members and Associates residing within the United States of America, Republic of Mexico and Dominion of Canada shall be entitled to vote at the meetings of the Institute. SEC. 2 All Members, Honorary Members, Associates and Honorary Associates of the American Institute of Mining Engineers as the same existed on the day of the incorporation of this Institute, are Members, Honorary Members, Associates and Honorary Associates, respectively, of this Corporation SEC. 3. The following classes of persons shall be eligible for membership in the Institute, namely, as Members and Honorary Members, all professional mining engineers, geologists, metallurgists or chemists, and all persons practically engaged in mining, metallurgy or metallurgical engineering ; as Associates and Honorary Associates, all persons desirous of being connected with the Institute who, in the opinion of the Council, are suitable. SEC 4. Every candidate for election as a Member or Associate of the Institute must be proposed for election by at least three Members or Associates; must be approved by the Committee on Membership, as prescribed in the By-Laws ; and .must be elected by the Council. Not less than three-fourths of the votes cast shall be necessary to an election Every person so elected shall become a Member or Associate, as the case may be, upon payment of his first dues as herein-after prescribed Each candidate for Honorary Member or Honorary Associate, must be recommended by at least ten Members or Associates ; must be approved by the Council ; and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of all the Directors present ; provided, however, that the number of Honorary Members and Honorary Associates shall not at any time exceed twenty SEC. 5. If any person elected a Member or Associate does not, within sixty days after notice of his election, accept the same and pay his initiation fee and dues for the current year, his election may be cancelled at the discretion of the Council.

Jan 1, 1910

By T. N. McVay, E. E. Creitz

Rather large amounts of titanium minerals and some zircon and monazite are being recovered from dune sands about I. miles west of Jacksonville Beach, Fla. The Mining Branch of the Bureau of Mines, Southern Experiment station, has been interested in developing additional large deposits of similar sands in other areas of Florida. The results of a field study have been published1 concerning the sands occurring on Trail Ridge which runs north and south about 30 miles southwest of Jacksonville. This investigation was undertaken in order to identify the opaque titanium minerals occurring in Trail Ridge and because of the economic importance of Florida titanium minerals. Nature of the Problem The minerals present in the heavy fractions (sp gr > 2.94) of the sands are principally opaque minerals; staurolite, zircon, sillimanite, tourmaline, kyanite, rutile, a small amount of corundum, traces of the zinc spinel gahnite and garnet. Epidote, monazite, hornblende and ti-tanite are present in other dune sands but these minerals were not noted in the samples collected on Trail Ridge. All of the minerals except those which are opaque can be readily identified by the usual petrographic methods. However, Opaque minerals cannot be examined satisfactorily by transmitted light. Polished sections of the opaque-mineral grains were examined but these sections did not furnish useful information. Consequently, it was necessary to use means other than the usual petrographic methods to identify them. Previous Investigations of Heavy Minerals in Florida Sands Martens2 has described the heavy minerals in the Florida beach sands and has classified the opaque minerals as ilmenite with minor amounts of leucoxene. Miller3 studied a number of sands collected by Ross and Mertie in Florida. He states that the material from the Florida beach and dune sands that commonly has been called ilmenite has essentially the chemical composition of the material that has been called arizonite.4 The x ray diffraction patterns of several samples indicated that the supposed ilmenite is essentially amorphous, with only weak lines corresponding to ilmenite, and hence the material is unlike the type of arizonite from Arizona. Opaque Titanium Minerals Rutile is essentially titanium dioxide. However, as pointed out by Dana,5 important amounts of Fe+2 and Fe+3 as well as Cb and Ta are reported in some analyses.

Jan 1, 1949

FOLLOWING the presentation of the papers by Messrs. Mahan and Butler, the discussion printed below ensued. A. C. LANE* With particular reference to the New England con-sumer, I entirely agree with Mr. Mahan that intelli-gent marketing methods will do a good deal, but there is more than one way of improving them. For instance, coal can be shipped best to New England about this time of year-after the storms of the winter and before the movement of crops in the summer. For that reason there ought to be seasonal freight rates. This will be agreed to by most coal men if you will ask them, especially those who are connected with large concerns like the Metropolitan Coal Co., and yet they do not get seasonal freight rates partly because the railroads are afraid if they once reduce them they will never have a chance to get them back again. But it would be an improvement to have seasonal freight rates. Another thing: When we are buying in New England we want really a certain amount of heat value in our coal. There is no great advantage in our buying ash, nor is there any particular advantage in the railroad shipping ash and clogging the circulatory system of the body politic any more than clogging the circulatory system of the physical body. It would be desirable if the wholesaler, and to some extent the retailer, could guarantee the amount of ash or sell their coal on heating value. If you are interested in that you will find some interesting charts, in "Anthracite Coal Costs Analyzed," a pamphlet issued by the Anthracite Coal Consumers Association, Inc., New York City, as to rates from various and sundry points for bituminous and anthra-cite coal from the field to New York, Buffalo and Chi-cago. Here in New England they are both up against the competition of oil. About 3 or 3 1/2 bbl. oil will do the work of a ton of coal. One of my millionaire friends who is well posted on the situation is putting oil in his Commonwealth Avenue house because it is the most economical. Moreover, we can get Welsh coal from across the water (and help equalize this matter of exchange with Europe) in close competition with Penn-sylvania coal.

Jan 4, 1928

By W. A. Binsacca

The concentrator treats sulfide ore containing lead, copper, zinc, gold and silver, at the rate of 850 tons per 24 hr., and produces lead, copper, zinc and iron concentrates by selective flotation methods. The ore occurs below the oxidized zone along a main fracture, the wall rock of which is either greywacke or calcareous shale. The predominating sulfide minerals are galena, sphalerite, pyrite and chalcopyrite; the others are quartz and calcite. In minor amounts, arsenopyrite, pyrrhotite and hematite occur, and such secondary minerals as smithsonite, chalcocite, covellite, bornite, cerussite and anglesite are detected in the ore, the last two named occurring principally as surface alterations of the galena. The ore is hauled from the mine bins in 10-ton cars which pass over the track scales before entering the car dumper ahead of the crusher plant.' A conveyor belt delivers the crushed ore to the sulfide bin, which has a capacity of 2800 tons. The primary grinding unit consists of two 6 by 12-ft. Marcy rod mills operating in parallel and in open circuit, each taking 425 tons per day. One rod mill discharges into an 8 by 25-ft. Dorr classifier with a 12-ft. bowl and the other into a 6 by 25-ft. Dorr duplex classifier. These classifiers are arranged so that each unit rakes the sands into a 6 by 14-ft. Traylor ball mill, which discharges to the bowl classifier only. The duplex classifier therefore operates in open circuit and the bowl classifier in closed circuit, the overflow of both classifiers furnishing the feed for the flotation section. Other groupings have been tried, but this has been found the most satisfactory. The Marcy mills are driven by 150-hp. slip-ring induction motors with speed reducers to give 17 r.p.m. The Traylor mill operates at a speed of 24 r.p.m. and is driven by a 200-hp. slip-ring induction motor, direct connected to pinion and gear. The bowl classifier operates at a speed of 22 r.p.m., with the bowl rake making 4.5 r.p.m. and the duplex classifier at 31 r.p.m. High-carbon steel rods of Mexican manufacture, 12 ft. long by 3-in. diameter, are used in the Marcy mills, with a resulting consumption of 1.52 Ib. per ton ore. The Traylor mill is fed 3-in. cast-iron balls cast in

Jan 1, 1935

By John J. Egan

THE present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire Submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all Substances that occur or that may be in any way associated with steelmaking operations, Such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee's earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. SPECIFIC HEATS, HEATS OF FORMATION, ENTROPIES AND FREE ENERGIES OF VARIOUS PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES. I . Determination of specific heats and entropies of oxides, sulphides, nitrides, etc. over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc. over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineralogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941