Search Documents

By E. Keller

Some years ago the writer's attention was called to the fact that rolling-mill scales from auriferous copper do not have the gold content proportional to the gold contained in the copper from which they are derived.' So, later, he made a few simple experiments, which are described herewith. In order to test the gold movement on the changing surface of a copper plate under the influence of oxidation, plates 6 in. by 8 in. by 1 in. (15.2 cm. by 20.3 cm. by 2.5 cm.) of converter copper, refined, of 99.29 per cent. purity, and leaded copper with a content of 95.65 per cent, copper, were obtained. Ten cuts were made through the thickness of the plates along the longitudinal center and the silver and gold content ascertained in each of the 10 samples in both plates, as shown in the accompanying illustration. The assay results, recorded in Tables 1 and 2, show that the gold distribution is relatively uniform in both plates, while silver has greater variations, especially in the leaded plate. The plates subjected to oxidation were placed in a red-hot muffle for about 2 hr., two small scarifiers being used as supports. Arranged alongside each other, they nearly filled the width of the muffle, and so were practically under equal conditions of heat and draft. The accurate observance of the time was not possible, however, because of other work, but the time of the exposure of each plate in a pair was identical. At the end of each period, each plate was plunged into water and completely freed of scale, which was carefully collected, dried, weighed, and analyzed. Samples of the plates had also been taken of the molten metal and duly analyzed. Table 3 contains the analytical data for the two plates and their several sheets, or layers, of oxide scales. These figures show that in the oxidations of the converter copper the silver is fairly uniform, while the gold is highly irregular and especially low in the first layer. In the oxidations of the leaded copper plate, the silver and gold contents are variable; however, this irregularity is due to two different causes. The

Jan 1, 1919

By G. A. Reinhardt, H. J. Cutler

ThE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4-in. (14.5 cm.) square bloom to a 3/4-in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900" to 950' C. and cooling slowly in mica. The test bars were tempered by heating to 825' to 875" C., quenching in water, and drawing to 515" to 535" C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. UlTimate Strength.. Elongation, Lb. pER Sq. In. PEE Cent.. in 4 In. Not LeEs Than Annealed specimens.............. 78,230 to 92,450. 18 Tempered...................... 120,000 to 149,350 9 After experience on this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850" to 900" C. and cooling in still air; the annealing, in heating to 850" to 900" C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were: yield point, pounds per square inch minimum, 44,800; ultimate strength, pounds per square inch, 89,600 to 112,000; elongation, per cent. in 2 in. not less than 17. Difficulty was encountered as soon as work on this material was started. Many precautions and refinements were instituted but it was found very difficult to secure the required elongation.

Jan 1, 1920

By Robert Parker

Measurements of the latent heat of transformation from a to 0 titanium were made using a pulse-heating technique. Rapid heating was accomplished electrically by discharging a low-inductance capci-tor hank through a thin-strip specimen. Both high-purity titanium and titanium containing 2700 ppm of 0 were studied. An electrical-resistivity technique and a plot of energy input us temperature rise were used to monitor the phase change. It was concluded that: 1) the latent heat of transformation is 800 i 48 cal per mole; 2) phase change occurred in less than 200 sec; and 3) the percentage phase change that occurs is linearly a function of the energy available for phase change. In addition, this experiment provides a simple and inexpensive method for determining specific heat of electrical conductors over large temperature ranges. The chief advantages of this technique over past pulse-heating experiments are: 1) static measurements of capacitor-bank voltage capacitance and specimen resistance can be made quickly and accurately to determine the energy supplied to the specimen; 2) the specimen is heated so rapidly (10 µ sec) that there is no appreciable heat loss during the heating. THE purpose of this paper is to illustrate the use of the capacitor bank as a tool for basic experimental investigations and to determine the rapid phase-change kinetics of titanium. The capacitor provides a number of unique properties: 1) rapid heating rates in the order of l09oC per sec can be obtained; heating rates as slow as l04oC per sec are available by merely adding a given amount of inductance to the circuit; 2) the energy input can be precisely determined and can be varied from several joules to millions of joules, depending on the bank capacitance and voltage; 3) the specimen can be heated uniformly through the thickness and length or non-uniformly, as desired; 4) the apparatus is simple and inexpensive and can be easily altered; 5) the form of the specimen can be wires, sheets, foils, rods, and cylinders; 6) there is great precision in the timing of events; 7) this technique may be readily used in conjunction with rapid cooling.

Jan 1, 1965

JUDGE Samuel E. Schull, in the Court of Quarter Sessions of Monroe County, Pa., handed down a decision on July 2, declaring the Pennsylvania law for the Licensing of Professional Engineers and Land Surveyors to be in violation of the Constitution of the State of Pennsylvania and also of the 14th amendment of the Constitution of the United States. The case was that of George E. Stevenson, who was arrested in June, 1922, charged with the practice of the profession of land surveying without first obtaining a state license. Mr. Stevenson had had forty years of practical experience as an engineer and land surveyor, and as set forth in the findings "had attained unusual skill, distinction and reputation in his said profession, and, on said date and for a considerable period thereto-fore and down to the present time, was and is President of the Engineer's Society of Northern Pennsylvania." That part of the decision referring to the unconsti-tutionality of the act is quoted in full as follows: This matter now comes on to be heard on argument as to the constitutionality of the said Act of May 25, 1921, P. I. 1131. The defendant urges that the same is unconstitutional: First: Because it is in violation of Article 3, Section 3, of the Constitution of Pennsylvania, which provides: "No bill, except general appropriations bills, shall be passed containing more than one subject which shall be clearly expressed in its title." Second: That the same is discriminatory and, therefore, in violation of the 14th Amendment of the Federal Constitution. In this case, we: are confronted by the Act of Assembly bearing the title "an act to regulate the practice of profession of Engi-neering and Land Surveying; creating a State Board for Regis-tration of Professional Engineers and Land Surveyors; defining its powers and duties, imposing certain duties upon the Common-wealth and Political subdivisions thereof, in connection with public work and providing penalties." We meet in the title of this act, a recognition of the fact that it is the legislative intent to deal with two professions: First: Engineering. Second: Land Surveying.

Jan 8, 1923

By Sid T. Killan

The utilization of the reducing power of blast-furnace gas can be estimated by applying two rectifying calculations to the gas analysis. A resulting corrected CO/CO2 ratio varies inversely with furnace production. Directions for calculating the corrected CO/CO2 ratio are given, and a corrected CO/CO2 ratio is compared with actual furnace production. THE inadequacy of the normally accepted CO/CO, ratio as a measure of blast-furnace performance and furnace efficiency was discussed following the presentation of the paper by H. F. Dobscha.' In this outstanding example of careful observation on large scale blast-furnace operation, the changes occurring with beneficiated ores were: 1—A net gain in tonnage of 21.2 pct. 2—A decrease in net coke of 15.3 pct. 3—A decrease of 1.9 pct in the CO/CO, ratio. In this great change in furnace performance, the CO/CO, ratio proved itself worthless. The discussion of the inadequacy of expressing furnace performance and efficiency by the CO/CO, ratio led indirectly to the calculations forming the basis of this paper. At that time Dr. T. L. Joseph said: "We must consider difference in CO, from the stone in the two cases when we talk about the ratios of CO/C02." This statement is used for the second of the two CO/CO, ratio corrections forming the basis of this paper. The research work in attempting to find out why the furnaces could op-erate so differently with practically the same CO/CO, ratio lead not to the answer sought but, after a shift to the gaseous phase in the research work, the proof that the normal CO/ CO, ratio was outmoded and a new corrected ratio should replace it. To be of any value, any new corrected ratio should express approximate furnace efficiency and give an idea of practical furnace performance to be expected. This the normal CO/CO, ratio has failed to do. However, in the absence of anything better, some credence has been attached to the normal CO/CO, ratio. As far as the writer can ascertain, the present paper is the first attempt to change or improve the normally accepted index of

Jan 1, 1952

By Berke L. Thompson

INTRODUCTION Purpose of Wall System There were 2379.88 m (meters) of tied back wall along Interstate 77 in the Capitol Complex area in Charleston, West Virginia. The main purposes of this wall system was for aesthetics, reduction of excavation, saving the forested slopes, and control of sloughage of the back slopes onto the Interstate. Failure At 1 PM on Thanksgiving Day, 1982, 3 wall panels fell from the insitu position onto the interstate in a matter of seconds. See Fig. 1. The total length of wall that fell was 29.25m. The height of the three panels varied from 10.06m to 10.36~1 and each individual panel had a length along the highway of 9.75m. These were abutting panels that were approximately in the middle of a section of wall 165.81m long. The panels separated from the remainder of the wall at 2 expansion joints that occur at the ends of every 3rd panel. The reinforced portland cement concrete panels were designed on a 76.2mm (millimeter) batter. See Fig. 2 for Wall Dimensions. The footer for these panels was lm wide, was keyed into sandstone bedrock 0.30m and was approximately 1.52m below the portland cement concrete pavement and shoulder. Thirteen of the 17 panels in this section of wall were tied to the sandstone bedrock behind the wall by either 25.4mm or 34.93mm hollow rock bolts. Two panels on each end of the wall were cantilever type walls. The panels that failed had 25.4m hollow rock bolts. A portion of each panel adjacent to both sides of the failure was pulled out from the rock face and appeared to be in imminent danger of also failing. All of the 21 rock bolts in the panels that fell were separated either at the backface of the wall, in the extension from the wall to the rock face or at the rock face. None of the rock bolts had been pulled out of the bond length in the sandstone bedrock. After considering the condition of the wall and

Jan 1, 1984

By Jack Washburn

The c axis indentations in zinc crystals were shown to undergo 100 pct strain recovery on heating. The mode of deformation and the details of the polygonization and collapse of indentations were found to be consistent with a number of predictions of dislocation theory. IT has been observed that indentations of the type made by Jillson in zinc crystals can, under certain conditions, be macle to shrink in size and even completely disappear on heating the crystal, Fig. 1. The details of the process are interesting in that they afford a simple experimental illustration of several predictions of dislocation theory. The indentations were made as shown in Fig. 2 by dropping a 0.2 g indenter with a hemispherical point on a cleavage face of a. zinc crystal. Such indentations can be made through relatively great thicknesses in the c-axis direction. The material close to the struck surface, where mechanical twinning and complex distortion occurred, was removed by cleavage. The remaining crystal, which was about 1 cm thick, contained a dent that was accurately round and almost the same size on both top and bottom surfaces. The indentation had the form of a flat cone of half angle approximately 89°, having a rounded apex and a rounded intersection with the unde-formed part of the crystal. The mode of deformation was primarily slip on the three equivalent systems in the basal plane. Six types of dislocation loop (plus and minus in each of the three directions) as shown in Fig. 3 are required by the geometry of the indentation. The maximum shear strain in the radial direction amounted to approximately 2.5 pct. Slip was distributed in the usual, microscopically nonuniform, manner among the possible parallel slip planes. When an indentation was made close to a (2110) surface, three separate sets of interpenetrating slip bands appeared as shown schematically in Fig. 3. A small biaxial tension strain in the plane of (0001) is also a geometrical necessity for the formation of an indentation. If the sides of the dent are tilted l° with respect to the undeformed surrounding crystal, and the surround-

Jan 1, 1957

By Andrew Corry

GEOPHYSICAL investigations based on radioactivity have been applied to the earth's crust for the purpose of discovering bodies rich in radioactive substances, or for the location of solutions with high emanation or radioactive-salt content, or for the detection of oil, which, in virtue of colloidal properties, has strong powers of radioactive absorption. RADIOACTIVE SUBSTANCES Radioactive substances are distributed in all rocks, waters, and gases in the earth's crust in small quantities. Granites and similar acidic rocks are richest in uranium and thorium, two chief radioactive substances; yet the quantities present in such rocks are of the order 10-12g., this concentration being expressed in grams per gram of the whole substance per cubic centimeter. In granites the uranium yields, according to Haddock, 3 X 10-12 g. of radium per gram of rock. In basalts the uranium yields 1.19 X 10-12 g. per gram per cubic centimeter. Of thorium the granites yield -2 X 10-5 g. per gram of rock; the basalts, 0.77 X 10-5 g. per gram. Certain series of alkalis of low atomic weight, like potassium and rubidium, show weak radioactivity; this property has no significance so far for geological research. The uranium is esti-mated indirectly from the electrical properties of one of its derivatives as a -gas (emanation) into which it is transformed. The thorium is expressed directly, though it is measured as a derivative, thorium emana-tion. There is a measure for the gaseous radium emanation, the curie, which is that quantity of radium emanation, or radon, which stands in equilibrium with 1 g. of radium. The concentration of the emanation is the Mache unit corresponding to 3.64 X 10-10 curie per liter. When gases become permeated by alpha, beta, and gamma rays, plus and minus ions are produced in them by the decomposition of neutral gas molecules, and under the influence of an electrical field these ions are given opposite motions. The measurement of the alpha rays and the bisection thicknesses of the beta and gamma rays is a means of analyzing unknown radioactive substances. These rays accompany the disintegration of radioactive substances and arise from "spontaneous internal changes

Jan 1, 1929

By Albert J. McIntosh

In discussing the petroleum products situation the first thing that comes to mind is "what is happening to gasoline." Is the consumption increasing? How is the export market? What about imports? Are stocks on hand too high? Have we produced too much? This paper will attempt to answer these questions. Consumption of gasoline (motor fuel) in the United States in spite of the depression and the chaotic conditions of many industries has increased during 1931 about 2 per cent over 1930. This favorable factor was offset by a severe contraction in exports, which fell off about 30 per cent from 1930. This drop in exports was so large that very little more export business was done than in 1926 or 1927. Taking all demand combined, there was a decrease from the peak year of 1930 of nearly 11,000,000 bbl., amounting to slightly over 2 per cent. The units of the industry, though, should have expected some decrease and governed themselves accordingly. Let us see what they did. They reduced imports over 3,000,000 bbl., which helped. Production was cut 3,000,000 bbl., but this was not enough, so that stocks increased 1,800,000 bbl. whereas during the previous year stocks were reduced 2,500,000 bbl. It is apparent, therefore, that something was done to keep the industry in balance in regard to gasoline, but not enough. If the year had ended on Sept. 30, we could have said that production had been cut 19,000,000 bbl. and stocks had been reduced from the previous year, but the excessive production during the last three months of the year changed everything. It is a strange thing and worthy of note that the price of gasoline fell to its lowest levels when apparently the greatest improvement was being made, and that during the last quarter of the year prices started to improve, when, in spite of an improvement in total demand which approximated 1930, an excessive production caused an uneconomic condition to set in. Stocks on hand on Dec. 31 were unquestionably too high, possibly 10,000,000 bbl. more than was needed for a strong condition to obtain. It seems almost unbelievable that the industry would continue to produce

Jan 1, 1932

By R. W. Lai, I. Iwasaki

Some physical as well as chemical aspects of the methods of dispersion of various corn starches and their derivatives are investigated and their effects as depressants in anionic silica flotation of iron ores ascertained. The adsorption behavior of starches on hematite and quartz is strongly affected by their molecular sizes as inferred from viscosity measurements. The implication of this behavior on flotation and flocculation is discussed. Mechanical treatment of causticized starch solutions is shown to reduce the starch requirements in flotation appreciably. Starches and starch products have been used as depressants for iron oxides both in amine flotation of siliceous gangue and in soap flotation of activated silica from iron ores. Cooke and his associates1,2,3,4 extensively studied the effects of certain starches and their derivatives in the amine flotation of iron ores at near-neutral pH and found that although most starches were good flocculants for hematite and de- pressed that mineral more or less selectively1,3 they did not flocculate quartz suspensions. Further, that replacement of active groups in corn starch modified its behavior as a flocculant for hematite or quartz suspensions1 and as an iron oxide depressant. Schulz and cooke2 showed that many starches and their derivatives, except aminoethyl starch, were abstracted more effectively by Brazilian hematite than by quartz and that the adsorption of a starch product was strongly dependent on pH and on the presence of calcium ion. In soap flotation of calcium-activated quartz, certain starches and their products have been used to depress iron oxides.5'6 The behavior of these substances in flotation appears at times to be at variance with those previously reported and especially with results obtained in the Mines Experiment Station laboratories. This is attributed, at least in part, to differences in flotation procedure and flowsheets and in the method of preparing the depressant. Most of the investigators referred to above, solubilized the starch products by autoclaving at 120°C. Others have used acid,7 alkali8 or oxidizing agents.9 In view of the limited knowledge of the depressing action of starches and their derivatives in iron ore flotation, particularly in soap flotation of calcium-activated silica at high alkalinity, an extensive study

Jan 1, 1965

By Geo. Otis Smith

Twelve years ago, the Director of the United States Geological Survey addressed to the Secretary of the Interior a letter calling attention to the government's need for liquid fuel for naval use and pointing out that the rate of increase in demand was more rapid than the increase in production.' This letter, in a way, inaugurated the policy of public oil-land withdrawals, which was well founded in its primary purpose of protecting the oil industry and highly desirable in its immediate effect of checking the over-development of that day in California. Unfortunately, however, through delays in legislation, this policy may be regarded now as having outlived both its intent and its usefulness. In 1908, the country's production of oil was 178,500,000 bbl., and there was a surplus above consumption of more than 20,000,000 bbl. available to go into storage. In 1918, 10 years later, the oil wells of the United States yielded 356,000,000 bb1.—nearly twice the yield of 1908—but to meet the demands of the increased consumption more than 24,000,000 bbl. had to be drawn from storage. Nor is this all of the brief comparison. In 1918, our excess of imports over exports of crude petroleum was nearly 33,000,000 bbl. whereas in 1908 we exported 3,500,000 bbl., which was net, as we had not begun to import Mexican oil. In this period, the annual fuel-oil consumption of the railroads alone has increased from 16,871,000 to 36,714,000 bbl.; the annual gasoline production from 540,000,000 gal. to 3,500,000,000 gal. This record may be taken not only as justifying the earlier appeal for Federal action, but as warranting deliberate attention to the oil problem of today. Need of Future Supply The position of the United States in regard to oil can best be characterized as precarious. Using more than one-third of a billion barrels a year, we are drawing not only from the underground pools but also from storage, and both of these supplies are limited. In 1918, the contribu-

Jan 1, 1921

By W. Klement

By quenching liquid alloys, single-phase solid solutions are obtained in the ranges 0 to 42.0 at. pct Co-Au and 0 to 15 and 75 to about 100 at. pet Co-Cu. Metastable solid solutions are also found in multiphase 42.0 to 49.0 and 69. 0 to about 100 at. pet Co-Au alloys. fie inability to achieve complete solid solubiliiies in Au-co and cu-co alloys is rationalized by a conszderation of the rate processes during cooling and solidification. Trends in lattice distortion and shifts in the compositions of the melting-point minima and critical points are discussed for the binary alloys of copper, silver, and gold with some of the transition metals of the first long period. By rapidly cooling alloys from the melt, a continuous series of metastable solid solutions can often be obtained for components of similar crystal structure which normally form eutectic systems.' The eutectic system Au-Co, Fig. 1, and the peritectic system Cu-Co, Fig. 2, were investigated in order to determine the extent of the metastable solid solutions attainable with the present technique.* EXPERIMENTAL PROCEDURES Most of the alloys were prepared by melting weighed quantities of the elements (purity greater than 99.9 pct) under hydrogen in alumina crucibles by means of induction heating. After reweighing, the alloys were cast under argon into 1 mm diam wires. However, it was not possible to prepare some of the Cu-Co alloys with the requisite homogeneity (over about 1 mm3) in this way. For these alloys, reduced powders (purity greater than 99.9 pct) were mixed for 12 to 48 hr, pressed into compacts that were sintered at 1000º to 1050°C for 6 to 48 hr under hydrogen, and then furnace-cooled. Alloy charges of a few mm3, cut from the cast wires or chipped from the sintered compacts, were heated to 1550º to 1600°C in 30 sec in an alumina insert held within a graphite support and then ejected by a pulse of helium onto a lightly polished copper strip on the inner periphery of a rotating wheel. The

Jan 1, 1963

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft, elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit, which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 1b.-pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 1/2 miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in Fig. 3. The two five-cylinder vertical Diesel engines, which are rated at 1,250 b.hp. at sea level, have cylinders of 525-mm. diameter (20.6 in.) and

Jan 1, 1917

By B. M. Loring, W. H. Baer, G. M. Carlton

It is a well known fact that age-hardening alloys remain in a supersaturated, or partially supersaturated, condition only for limited periods of time at temperatures below the solvus. In order to develop optimum properties by subjecting the quenched alloy to precipitation or age-hardening treatment at a specified temperature, it is necessary that the cooling rate be sufficiently high to maintain the required degree of supersaturation of the solid solution. In practical applications the size and shape of the specimens obviously have considerable influence on the rate of cooling and there is need for more information on the effects of various rates of cooling. Cooling rates of quenched aluminum alloys generally have been established by the type of quenching medium, the temperature of the medium and the dimensions of the specimen. Except for the work of Roth3 little quantitative information is available on the measurement of cooling rates of aluminum alloys and the significance of the influence of various cooling rates upon the mechanical properties. The purpose of the present investigation was to study the use of the Jominy test for aluminum alloys (Table I). The material for this investigation consisted of extruded rods 1 1/4 to 136 in. in diam. The chemical compositions were as follows: The modified L-type Jominy specimen with dimensions shown in Fig I was selected as the most convenient means for obtaining a wide range of cooling rates. The standard Jominy specimen was not satisfactory because its cooling rate was not sufficiently high. The four flat surfaces machined at right angles along the length of the L-type specimen to a depth of 0.015 in. facilitated the hardness measurements. The specimens were machined from the extruded stock with no intermediate forging. New specimens were used for each aging experiment. The specimens were given solution treatments of 2 hr duration at recommended temperatures in a Hoskins furnace (Table 2). The temperature of the furnace was maintained constant to 3°C. No protective atmosphere was necessary because the thin film of oxide that formed on the surface of the specimens had no effect on the hardness measurements. AT

Jan 1, 1949

By F. J. Tuck

The Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a ¾-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 days. Manganese-steel lifter bars, 3? in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 days. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1½-in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood backing is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots, and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 25 to 33 per cent of the ore. Additional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department. Rods are charged to the mill once every four days, the mill being down about 20 min. for this purpose. Other delays are negligible, and usually are due to a loose liner bolt or possibly power trouble. However, these occasions are extremely rare. In charging the mill, a crane is used

Jan 1, 1939

By Eric R. Jette, Earl S. Greiner

The constitution of the iron-rich iron-nickel-silicon alloys at 600ºC. has been determined by X-ray crystal structure methods. If the results are represented isothermally by a conventional equilateral triangular plot, the single-phase solid solution (body-centered cubic structure) of the iron-rich alloys at 600°C. is bounded by four two-phase areas. Three three-phase areas separate the respective two-phase areas. Three of the phases in the polyphase areas have the same structures as the corresponding phases in the binary iron-nickel or iron-silicon alloys. There are two phases, however, that have not been reported previously and whose structures have been tentatively identified in the present investigation. The solid solubility limit of the iron-rich solid solution at 600°C. was determined by comparing the lattice constants of this body-centered cubic phase in the single and polyphase areas. It has been shown that the lattice constants of ternary alloys may be represented by surfaces whose distances above the ternary plot (representing atomic composition) are proportional to the lattice constants of the respective alloys. Then the intersections of the surface for the single-phase alloys with those for the corresponding phase in the polyphase alloys, at the respective temperatures, are the solid solubility limits of the single-phase alloys at these temperatures. The data of the present investigation were evaluated by this method, although by a system of orthographic projection it was possible to represent the three-dimensional model in two-dimensional diagrams. This investigation has shown that the solid solubility of nickel in the body-centered cubic phase of the iron-rich iron-nickel-silicon alloys at 600°C. changes from 3.7 weight per cent (Owen and Sulley) in the binary iron-nickel alloys to 5.0 per cent in the ternary alloys containing 4.8 per cent silicon. Further additions of silicon increase the solid solubility limit of nickel to 16.0 per cent at 12.6 per cent silicon. From this point the limit decreases to 9.5 per cent nickel at 15.5 per cent silicon and is, of course, zero at 15.3 per cent silicon in the binary iron-silicon alloys.

Jan 1, 1943

By F. J. Tuck

The Hayden mill of the Ray Mines Division, Kennecott Copper Corporation, is now equipped with two 9 by 12-ft. rod mills having a daily capacity of 6000 tons of coarse-crushing plant product from the mine. These two mills crush a ¾-in. product to approximately 19 per cent on 14 mesh, with only one pass through the mills. Each rod mill has taken the place of four sets of 42-in. Garfield rolls with their attendant screens, and is making a product for the fine-grinding department comparable to that formerly made by rolls in closed circuit with screens. The rod mills are lined with wave-type liners of white iron, varying in thickness from 2 to 3 in. The shell and end liners last approximately 600 to 700 days. Manganese-steel lifter bars, 3? in. thick, are used, spaced about 11 in. apart, and they give a life of 350 to 450 days. Fig. 1 shows the general design and thickness of the wave-type liners and lifter bars; 1½-in. liner bolts are used to fasten the lifter bars to the shell. The shell liners are held in place by the tapered lifter bars. A ¾-in. wood backing is used between the shell and the liners. The rod-mill scoop has removable manganese-steel lips, which last 250 to 300 days. The scoop proper has shown some wear in spots, and these spots have been protected by rubber bolted over them. Water and milk of lime are added to the elevator feeding the mill, but not enough water to cause a pounding of the rods against the shell. Roughly, the water added amounts to 25 to 33 per cent of the ore. Additional water is added to the mill discharge to facilitate distribution to the classifier bowls in the fine-grinding department. Rods are charged to the mill once every four days, the mill being down about 20 min. for this purpose. Other delays are negligible, and usually are due to a loose liner bolt or possibly power trouble. However, these occasions are extremely rare. In charging the mill, a crane is used

Jan 1, 1939

By Earl S. Greiner, Eric R. Jette

The constitution of the iron-rich iron-nickel-silicon alloys at 600ºC. has been determined by X-ray crystal structure methods. If the results are represented isothermally by a conventional equilateral triangular plot, the single-phase solid solution (body-centered cubic structure) of the iron-rich alloys at 600°C. is bounded by four two-phase areas. Three three-phase areas separate the respective two-phase areas. Three of the phases in the polyphase areas have the same structures as the corresponding phases in the binary iron-nickel or iron-silicon alloys. There are two phases, however, that have not been reported previously and whose structures have been tentatively identified in the present investigation. The solid solubility limit of the iron-rich solid solution at 600°C. was determined by comparing the lattice constants of this body-centered cubic phase in the single and polyphase areas. It has been shown that the lattice constants of ternary alloys may be represented by surfaces whose distances above the ternary plot (representing atomic composition) are proportional to the lattice constants of the respective alloys. Then the intersections of the surface for the single-phase alloys with those for the corresponding phase in the polyphase alloys, at the respective temperatures, are the solid solubility limits of the single-phase alloys at these temperatures. The data of the present investigation were evaluated by this method, although by a system of orthographic projection it was possible to represent the three-dimensional model in two-dimensional diagrams. This investigation has shown that the solid solubility of nickel in the body-centered cubic phase of the iron-rich iron-nickel-silicon alloys at 600°C. changes from 3.7 weight per cent (Owen and Sulley) in the binary iron-nickel alloys to 5.0 per cent in the ternary alloys containing 4.8 per cent silicon. Further additions of silicon increase the solid solubility limit of nickel to 16.0 per cent at 12.6 per cent silicon. From this point the limit decreases to 9.5 per cent nickel at 15.5 per cent silicon and is, of course, zero at 15.3 per cent silicon in the binary iron-silicon alloys.

Jan 1, 1943

By J. Campbell

Long freezing range casting alloys are particularly susceptible to a type of porosity which is observed to form in layers parallel to the supposed position of the isotherms in the solidifying casting. Under favorable conditions (which appear to be typified by low-temperature gradients in the casting giving rise to a wide and more or less uniform pasty zone, and which arise from several factors, particularly: a) wide freezing range alloy, b) high thermal conductivity of metal, c) low thermal conductivity of mold, and d) high mold temperature3) layer porosity has been observed in many different casting alloys: copper,' aluminum, magnesium,' steels, and high-temperature alloys.3 Baker4,5 and later cibula6 argue that layer porosity occurs because of thermal contraction, in a manner analogous to hot tearing. In outline, the theory consists of the establishment of a coherent dendrite network by the impinging of dendrite tips. Subsequent shrinkage imposes tensile stresses on the network which tears perpendicularly to the stress, i.e., parallel to the isotherms. If these tears are not filled by the inflow of residual liquid then layers of porosity result. Baker7 attempted to test whether the porosity was the result of thermal contraction by casting test pieces in a mold designed to accentuate hot tearing. However, no significant increase in porosity was observed. This negative result of Baker's critical experiment appears to be substantiated by numerous observations, particularly the experiments by Lagowski and Meier8 on Mg-Zn alloys covering the range of zinc contents up to 30 pct Zn. These clearly reveal that the maxima for the incidence of hot tearing and layer porosity are well-separated, occurring at 1 and 6 pct Zn, respectively. Furthermore, the thermal contraction maximum occurred at 1 pct Zn, indicating that hot tearing is associated with contraction in the solid state, and not with porosity. These observations are further substantiated by the elementary consideration that the thermal contraction of the casting is likely to produce (if anything, since the temperature difference across casting of high thermal conductivity, such as aluminum and copper, is likely to be negligible) a compressive stress on the

Jan 1, 1969

By Paul C. Ragland, P. Geoffrey Feiss

The Piedmont province of the southern Appalachians is the focus of interest for many exploration geologists. In the past, only those deposits with significant surface exposure were exploited. Thus, few deposits have been found and relatively little exploration has been conducted in recent years. Modern geochemical and geophysical techniques can alleviate this problem of concentrating on exposed ore bodies by allowing us to "look through" the soil and saprolite to detect the presence of significant mineralization at depth. This paper will attempt to evaluate the feasibility and effectiveness of several geochemical exploration techniques in the Piedmont province of Cabarrus and Stanly counties, N.C. The area chosen for study is shown in [Fig. 1], lying almost wholly within the Mt. Pleasant quadrangle, N.C. The area is on the eastern boundary between the Charlotte belt, a zone of plutonic and intermediate grade metamorphic rocks, and the Carolina Slate belt, a series of complexly interbedded volcanic and sedimentary rocks of predominantly low metamorphic grade. The area is considered to be an early Paleozoic active, continental margin. l As is typical of most of the piedmont, outcrop is sparse. [Figure 2] is a sketch map of the general geology of the area under study, showing the Charlotte belt rocks in the northwestern quadrant and slate belt rocks to the east. Within the area are a number of old mines and prospects, the most famous of which are the Furniss and Phoenix mines in Cabarrus County. All are reported to have contained Au and Cu. Ag and Pb were reported from some. A summary of the deposits is given in [Table 1]. Data used in this study are from three Master's theses completed at the University of North Carolina at Chapel Hi11. 3, 5, 6 In separate studies, well waters, 5 B-zone soils,3 and vein and float from the area were sampled and analyzed. Each study concluded separately that geochemical anomalies in the vicinity of the ores justify use of that specific sampling technique in a geochemical exploration program. However, no comparative study of the methods has been made. It is our intention

Jan 1, 1980