Search Documents

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

Jan 1, 1903

By Stanford O. Grodd

The Sanford Lake district encompasses an area covering 24 square miles in the central Adirondack Mountains of northern New York State. Discovery of the titaniferous magnetite deposits dates back to 1826. Several attempts to exploit the ores for iron prior to 1942 proved uneconomical because of difficulties with the associated titanium, lack of transportation facilities, and the isolated location. Since 1942, the National Lead Company has produced ilmenite concentrates for the titanium pigment industry, and a magnetite by-product used in the steel and refractory industries. Rocks of the area are Precambrian in age and of igneous origin. The area has a history of erosion, deformation, and metamorphism, subsidence, and finally uplift and glaciation. The resulting topography is extremely rough with drainage patterns controlled by a combination of fault patterns and glacial modifications. The district is within the large anorthosite massif making up the central high peak area of the Adirondacks. All of the various lowsilica rock types associated with the massif are found within the boundaries of the district. These consist of both the Marcy and Whiteface types of anorthosite and of gabbroic anorthosite, gabbro, and different grades of titaniferous magnetite ores. All of the rocks contain the same minerals and differ only in their percentages of these consitituents. Gabbro, and ore associated with it, demonstrate flow structure as both have foliation and lineation. Anorthosite and its associated ores are massive and show very little primary structure. Minor pegmatites and diabase dikes provide evidence of remobilization in selected areas and of late intrusion as well. Faulting is prevalent and follows a regional pattern of major faults trending northeastsouthwest and of minor faults at nearly right angles to them. There are four mineralized areas where an economic grade of ore has been found. Three of these have both gabbroic-type ore and anorthositic-type ore. The fourth has only gabbroic ore. Ores are graded according to their TiO, content, and these range from 9.5 per cent to over 30.0 per cent TiO,. Ore bodies of both types are related to gabbro and conform to the configuration of the gabbro bodies within the anorthosite. At least three distinct theories of ore genesis have been expounded by different investigators. Others propose some variations of one or more of these. Although complete agreement probably never will be reached, it is certain that no one process of ore emplacement can explain the complicated picture as seen today. Further understanding of the ores and their origin will require detailed mapping, sampling, and mineralogical studies of the entire district, and then it may never be understood without qualification.

Jan 1, 1968

Mining and oil industry representatives are scheduled to testify May 15 at hearings on the Simpson bill to extend the Reciprocal Trade Agreements Act, Several Congressmen have introduced bills to extend present trade agreements without modification. Price of copper appears to be stabilizing at 30[] per lb, after a period where market price ranged from 27 to 34[]. Copper offerings from abroad were finding no takers at 30.24[] per lb late in April.

Jan 5, 1953

By AIME AIME

THE United Electric Coal Companies, operating large strip mines at various points in Illinois, pioneered in developing and perfecting the strip method of mining coal by use of large shovels and drag-lines. Coal stripping was first started on the properties owned by this company near Danville, Ill., in 1885. The first mechanical' excavating machine used for the purpose was really a dredge minus the hull, which had been purchased from the Marion Steam Shovel Co. It was erected on a wood frame supported by wheels and was referred to as a dry-land dredge or stripping machine. Wood was used throughout in the construction of this primitive excavator, even for the boom which was 50 ft. long. A single-cylinder vertical steam engine furnished power to hoist the %-yd. dipper arid swing the boom. 400 cu. yd. of overburden moved in a day was a great record.

Jan 1, 1936

By Games Slayter

NO reasonably well-informed person believes that the role of minerals, both metallic and nonmetallic, will be any less important in the future than it has been in the past. The contrary is true. Industrialization is based on mineral resources and man's ability to make use of them. A nation's standard of living, its political and military power, will continue to depend largely upon the extent to which it is industrialized-and minerals are the raw materials both of the machine and the power to run the machine. Minerals are also the raw materials of human health and stamina. The world's healthiest, most vigorous, and most long-lived peoples have always been those that have lived in regions of the globe where the earth is rich, and kept rich, in the phosphates and other minerals required for the production of the so-called growth foods. Only a small proportion of the land surface of the globe is suitable under any circumstances for large-scale production of these and other essential foods. As things stand, only a part of this land is capable of such production either because the soil minerals have been exhausted by cultivation, or because they never existed in the soil in sufficient quantities.

Jan 1, 1943

By Mazany, M. S.

THE Caletones copper smelter of the Braden Copper Co. is in the " Teniente" mining district about SO km. (49.7 mi.) southeast of Santiago, Chile. From the seaports of San Antonio and Tralparaiso, the property is reached via the Chilean State Railway (66-in. gage) to Rancagua, whence the Braden railroad (30-in. gage) leads to the smelting plant at Caletones, 60 km. away at 5100 ft. elevation, and continues on to the mine and concentrator at Sewell, at 7000 ft. elevation, 12 km. farther into the Andes. The smelting plant was completed and put into commission in February, 1922. At the start, it smelted daily 750 tons of concentrates produced at Sewell from 10,000 tons of ore; later, its capacity was increased to 900 tons of concentrates from 12,000 tons of ore per day; and it is now being increased to 1100 tons of concentrates from 15,000 tons of ore per day. The smelting plant production is governed chiefly by the

Jan 1, 1925

By Oswald J. Heinrich

(with figures on plate V.) THE origin of spontaneous combustion in collieries is, of course, chiefly due to bad system in laying out the pits, unclean workings, insufficient ventilation, and neglect in damming off works after they are exhausted of the main coal. This is particularly indispensable in the Richmond field, because it is difficult and dangerous here, on account of the inferior roof, to remove the last vestiges of coal ; and we are compelled also to retain all the slates and bands, as far as possible, in the pit, to help fill up, although such material is liable to fire. This, however, can be prevented to a great extent, as men¬tioned below. I am satisfied that the only system of working this thick coal is by cross-cutting ( Querbau, ouvrage à travers) or working in benches, as practiced in France (Creusot, Rive de Gier, St. Etienne), in Sile¬sia (Königsgrube), which I have used as far as it is practicable in an old pit, almost torn to pieces by former workings. Modifications may, of course, be needed, even in the same pit, on account of irregu¬larities in the seam. I am also satisfied for economical reasons (on account of the heavy cost for timbering) that pits here ought to be worked upwards, even if it requires a longer period of time to win the coal, and a greater outlay of capital to commence with. The various saddle-shaped "troubles" making natural minor basins in the main basin aid in the execution of this plan. A pit worked once ought to be worked out clean, given up, and dammed off forever. If sections of proper height are assumed, according to the required amount of production for a certain period of time, they ought to be worked out and filled in as much as possible, dammed off, and ulti¬mately allowed to fill up with water, in order to protect the tipper works in future from fire in the gob below. This I consider indispen¬sable, because we may not be able profitably to fill in all the ground. To do so we have to use the waste of the mine, although it is liable to fire in time. In using this stuff, it ought to be surrounded by walls of rock not liable to take fire, laid firmly in clay, the gob being in the middle, and firmly covered and packed with clay on top. In

Jan 1, 1873

By J. B. Gayle

PRESENT flotation processes depend almost entirely on the buoyant properties of air bubbles to effect separations of mineral and gangue, but there is no convenient method for measuring aeration in flotation cells. Consequently the relation between aeration and cell performance has not been definitely established. In connection with a comparative study of kerosene and froth flotation processes, a modification of the displacement method' was developed in which air escaping from the cell surface is measured with a wet-test meter. The arrangement shown in Fig. 1 is satisfactory for use with a number of cells and is not critical, except that care must be taken to use connections and tubing large enough to avoid excessive back pressures. Attempts to use smaller tubing resulted in back pressures that caused displacement of the liquid level in the receiver, so that some air was lost around the sides, an occurrence readily visible when measurements were taken with only water passing through the cell. With the arrangement shown, the manometer indicated an average reading of about 1/2-in. water pressure. No loss of air was evident. Fig. 2 presents typical data for a standard Denver sub-A 24x24-in. unit cell operated at impeller speeds from 0 to 710 rpm. Each plotted point represents the average for five readings distributed over the entire cell surface. Readings were taken with only water passing through the cell. Results of this type have been used in a study of the influence of operating variables on cell performance and in detecting inherent differences in the operating characteristics of cells of various kinds. Although the information presented in Fig. 2 resulted only with water passing through the cell, the apparatus is suitable for use during flotation of coal when various reagents are present. Possible modi- fications that might prove convenient under special circumstances include varying the size and shape of the receiver and substituting a calibrated, inverted, water-filled carboy or other gas-measuring device for the wet-test meter. If such modifications result in excessive back pressures, some form of draft should be applied at the discharge end of the measuring system.

Jan 1, 1959

By W. L. Dumoulin

A RATHER detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,1 so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year, 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily, capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to ¼ in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in.. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 ½ by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane.

Jan 8, 1919

Jan 1, 1967

By N. S. Wagner

The production of lightweight aggregates in Oregon is a new industry, and, like all new enterprises, it is suffering from growing pains characterized by numerous, small operations some of which flourish for a short time and then cease altogether. Normally all industrial mineral products are produced in a highly competitive atmosphere. At the present time this condition does not exist to a very marked degree in the state because as yet producers have not saturated the constantly expanding market. This paper has been prepared with the intention of outlining very briefly the current status of the various products now being used as lightweight aggregates in Oregon. The present picture will surely change, perhaps quite radically within even a short space of time.

Jan 1, 1949

By F. C. Foshag, P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corp. operates a modern coal preparation plant in Van, WV. Since start-up of the Van plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miners' vacation, the original system - which included two screw conveyors and a drag conveyor - was replaced by an installation using two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance.

Jan 1, 1983

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization and at a minimum of expense. J. V. W. Reynders is chairman of the Endowment Committee.

Jan 1, 1923

Jan 1, 1967

By Claus G. Goetzel

SOME of the reactions and procedures upon which modern techniques in the production of metal powders are based were used for 2000 years by the ancients to reduce iron and other metals from their ores. Despite this, however, the art of powder metallurgy is relatively new and probably stems from the introduction of incandescent electric lamp filaments. Attempts to improve upon Edison's carbon filaments led to the production, in order. of metallic filaments of osmium. tantalum.. and finally of tungsten, which ha, replaced the others and is the commercial product of today. These metallic filaments were originally manufactured by the extrusion and sintering of a mixture of the metal or its oxide with a reducing agent which also served as a binder. Further progress in this direction was in the pressing of a small percentage of nickel with the tungsten. The sintering operation was carried out in an atmosphere of hydrogen, at a tem-

Jan 1, 1944

By W. A. Anderson

IN the pressure die-casting of zinc alloys it is customary to force the molten alloy under high pressure into a permanent steel die by means of a plunger moving in a bushing that has a clearance on the diameter of the order of 0.002 in. Successful operation of the plunger type of machine requires the presence in the zinc alloy of certain percentages of aluminum. Without these aluminum additions, the normal reaction of molten zinc on ferrous materials causes sticking of the plunger and a complete shutdown of the equipment. All of the zinc alloys used for pressure die-casting today contain approximately 4 per cent of aluminum, which is more than sufficient to make plunger operation feasible. The clearance between the plunger and its bushing is an important matter. As the space becomes larger, there is a loss in effective metal pressure. Ordinary gray cast iron served fairly well and is still used in some machines. However, the rate at which the plunger clearance increases with this material is considered by many to be far too great. There is, therefore, a serious interest in finding new materials more capable of retaining the desired clearance during long periods of use. Today many die casters are using special materials for plungers and bushings selected by the somewhat expensive and time-consuming test of actual experience. An analysis of the problem reveals two possible end points of plunger operation: (1) the building up of zinc-alloy plunger-material reaction products in sufficient bulk to cause sticking and (2) rapid solution, wear or erosion, all of which will increase the clearance to an undesirable extent. If neither of these takes place, the plunger will operate for a long time, of course. The authors have developed a laboratory apparatus in which the action of a plunger moving in a bushing immersed in molten zinc alloy could be simulated closely. Such a machine made possible a more rapid and less expensive survey of the available construction materials and an analysis of the specific alloying reactions taking place in the clear-ance area.

Jan 1, 1939

By I. Zaplatynskyj, G. C. Kuczynski

SINCE the excellent studies of metal powder compaction executed by Kamm, Steinberg, and Wulff, no work on the subject has appeared in the technical literature. Kamm et al. were the first to investigate quantitatively the distribution of density in a powder compact, as a function of pressure, height and diameter of the die, powder particle size, etc. For this purpose they devised a very ingenious method. They inserted a thin lead grid into a die and then filled the die with powder. During cold pressing, the lead grid -moved downward. Due to its deformability it followed closely the downward descent of the adjacent powder. The die was then radiographed and, from the deformations of the grid openings measured on the radiographs, the density in the vicinity of each opening was evaluated. Their findings led them to the conclusion that the friction on the side walls of the die is a major controlling factor of the density distribution inside the cold pressed powder compacts. However, it is difficult to conduct tests similar to those of Kamm, Steinberg, and Wulff in a processing plant laboratory, which usually lacks the necessary expensive radiographic equipment. The purpose of this note is to describe a method which makes it possible to determine the density distribution in green powder compacts with the same accuracy as the lead-grid method but which is far simpler and faster and requires only standard laboratory equipment. Instead of using a lead grid, the hardness at selected points of the sectioned compact is determined. If the relationship between hardness and density is known the density distribution is readily obtained. This relationship is easily found from measuring hardness and densities of thin compacts. In such compacts the density, for all practical purposes, is constant throughout. The method was tested on a Plast nickel powder, grade FlA-A20, kindly supplied by Plast Metals Co. Thin compacts (height to diameter ratio 0.2) were pressed in a single action cylindrica1 die at various pressures. The density of the compacts was determined by weighing and by measuring the height and diameter with a micrometer. Subsequently the Rh hardness was determined. Up to ten readings were taken on each specimen. The difference in hardness readings on each compact was never greater than three corresponding to about 0.1 g per cu cm uncertainty in density. By varying the compaction pressure of the samples, a whole scale of densities was obtained allowing construction of a set of density-hardness calibration curves. To test the method several compacts of different height were pressed under varying pressures. Die walls were always well lubricated. After pressing, the compacts were mounted in bakelite and halved by grinding, and hardness readings taken along the diameters of the specimens. The distance between adjacent indentations was about 2.5 mm. After hardness readings were translated into densities, contour maps of densities of the compacts were prepared. One of them is reproduced in Fig. 1. The areas encompassed by the curves are labeled with numbers representing the density in g per cu cm of those regions. In Fig. 2 the same results are re-plotted to emphasize the radial density changes at various depths. The results thus obtained confirm the findings of Kamm, Steinberg, and Wulff kentioned previously. They are recapitulated here briefly. 1—The densest part of a compact pressed from one side is at the outer circumference at the top and the least dense part at the bottom, at the outer circumference. Figs. 1 and 2 show this clearly. 2—The density near the cylindrical surfaces of the compact decreases uniformly with height from top to bottom. 3—The density variation increases with the height to diameter ratio. References R. Kamm, M. A. Steinberg, and J. Wulff: Trans. AIME (1941) 171,'R. p. 439 ;MetaLs Technology (February 1941). R.p. Kamm, M. A. Steinberg, and J. Wulff: Trans. AlME (1949) 180, 2R.P. 694; MetalS Technology (December 1948).

Jan 1, 1957

By F. C. Wagner, E. P. Klier, D. E. Nulk

The presence or absence of plastic strain at a cleavarage surface is a question of much importance, and upon its answer depends future possible theoretical work. To investigate this question back-reflectinn X ray patterns were obained on the cleavage facets of ferrite grains. The test set-up consisting of FeK colli- mated radiation, single grain material and stationary cassette and specimen will not lead to a diffraction pattern, in general, but is an ideal arrangement for the exami-nation of surface effects. A pattern taken on hydrogen purified

Jan 1, 1949