Search Documents

By G. E. Archie

Data given in this paper indicate that certain relations exist between different characteristics of sandstone. These relations are not rigid, for all sandstones are more or less heterogeneous. Not every increment of a given horizon follows exactly the relationship; however, studying a reservoir as a whole from a large number of samples, definite trends are found to exist. Apparently nature's processes of sedimentation and diagenesis are such as to give some degree of uniformity. Average relationships are valuable because electrical measurements in a borehole comprise a considerable volume of rock near the hole. Also, it is desirable that a given producing reservoir be studied as a unit. In a permeable reservoir whose pores are filled with a saline solution, it was found that the total porosity and the type of sandstone influence the relationship between its electrical resistivity and the RO and the resistivity of the brine R,. The relation can be expressed by the following empirical equation, Ro = R10O— [i] where 0 is the porosity expressed as a fraction and the numerical value of the exponent lies between 1.8 to 2.0 for consolidated sandstones, and is about 1.3 for clean, unconsolidated packs. This equation indicates that an appropriate electrical log can be used to estimate the porosity of a saline water-bearing reservoir when Rw and the type of rock are known. The fraction R0rw, is called the "formation resistivity factor." It reflects the effect of the nonconducting rock structure on the resistivity of the salt water that fills the tortuous paths through which the electricity must pass. The formation resistivity factor F is found to be related to permeability k. In this case the type of rock plays an important role, as shown by the relation F = ak-b [2] where the values of a and b must be determined experimentally for each horizon. Therefore Eq. I rather than Eq. 2 is used when it is desired to determine the value of F, because small changes in rock structure particularly in the pore size are not critical. Another useful relation, R = R0S- [3] where R = resistivity of rock when partially saturated with brine and partly with oil or gas, S = fraction of the pore space filled with brine, and n equals approximately 2 for both unconsolidated and consolidated sandstone, shows that the connate water of an oil or gas reservoir can be estimated in situ from a resistivity log. Equation 3 shows that in order to estimate the water content of a reservoir a knowledge of R and Ro is essential. The first value can be obtained from the electrical log when all factors influencing the resistivity curve can be properly taken into account. The latter may be obtained when a log is available on the same horizon where it is entirely water-bearing and has

Jan 1, 1946

By Emma Smith, R. W. Guard

INVESTIGATION of the nickel-rich end of the Ni-Zr system has been prompted by an interest in the effect of small amounts of zirconium in high temperature alloys. Hansenl presents a hypothetical diagram based on the work of Allibone and Sykes,2 who investigated the system up to 44 atomic pct (55 wt pct) Zr by metallographic means. Since the alloys they used were melted in Alundum crucibles they were probably contaminated with appreciable amounts of aluminum. They found two compounds which they called Ni3Zr and Ni4Zr. Hayes, Roberson, and Paasche3 identified a compound NiZr (50 atomic pct Zr) with a melting point of 1470°C. Such a high melting compound is not compatible with the observation of Allibone and Sykes2 hat a eutectic is formed near 50 atomic pct. The alloys containing up to 60 atomic pct Zr were melted in an inert atmosphere in a noncon-sumable electrode arc furnace. Analysis of most of the alloys indicated negligible loss of zirconium. The alloys were examined in the as-cast condition and also after annealing for 6 hr at 1175°C (or 1000°C for the alloys between 25 atomic pct and 45 atomic pct). Metallographic specimens were etched using mixtures of HF-HNO3-H2O or acetic acid- HN0,-H,O. The specimens for the solidus determinations were wrapped in molybdenum foil and sealed in evacuated quartz tubes. Specimens to be heated above 1300°C were enclosed in zirconia tubes inside the quartz to prevent reaction with molybdenum. The solidus determinations were carried out by heating the specimens at various temperatures for a few minutes and then examining the interior structure metallographically to determine at what temperature melting began. The 150 mesh powders for X-ray analysis were annealed in an evacuated quartz tube for 2 hr at 540 °C to remove cold work. Alloys with 22.5 atomic pct Zr and 44.4 atomic pct Zr required annealing at 700 °C for complete recovery. The grains of both of these alloys were soft and rather ductile. Both Debye-Scherrer film patterns and spectrometer traces were made for each alloy using filtered copper radiation. Results and Discussion The presence of a substantial amount of second phase in an alloy with 1.1 atomic pct Zr indicated that the solid solubility of zirconium in nickel is somewhat less than 1 atomic pct. The a0 value for the face-centered-cubic matrix in the same alloy was equal to that of pure nickel, so that the solubility must be very small. This observation is as expected from the large atom size difference. Annealed specimens of alloys with 15.0, 16.7, 22.5, 28.6, 44.4, and 59.4 atomic pct Zr showed. micro-structures that were essentially single phase. When

Jan 1, 1958

By Reed W. Hyde

Some information has been published on the sulphur dioxide concentration of gases from D wight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes Over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide notation concentrates mixed with minus 20.mesh oxide ore, the mixture carrying 16,8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily. to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO z might be utilized, a series of runs was made to determine the concentration ofSO2 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1 2 to 1 in., ('1 4 to 3% in. and (3) 6 to 5% in. The averages of the determinations from each series are platted On the graph (Fig, 1). The vertical scale shows the percentage by volume of SOz (as determined by the Reich method), and the horizontal scale shows the time e~pressed as percentage of the total sintering time. Sintering was considered to be complete when no SOz could be detected in the gases. In all cases the depth of bed was 4 1/2 in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which SO2 determinations were made could not be measured, but has been calculated from the SO2 Content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume usually will drop slightly toward the middle of the period and increase toward the end. However, this made is a reasonable approximation. several interesting features are brought out by these data. In general, the published data on SO 2 concentration in sintering under ordinary conditions show a high SO2 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SOz in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum SO2 concentration is obtained 234 min. after

Jan 1, 1944

By Cuppam Dasarathy

THE object of this note is to report briefly certain results of investigations on the Fe-In phase diagram. BISRA-high purity H-iron and 99.9 pct pure indium were used to prepare the alloys. The experimental techniques consisted of thermal analysis, optical metallography, and X-ray diffraction. A phase diagram based on the present results as well as those reported earlier by the author' is shown in Fig. 1. It is seen that the liquidus points fall on a smooth line which meets the monotectic isotherm at 1470°C. The liquidus extends up to 3.4 at. pct In. The phase boundary separating the two liquidus L1 and L2 is shown dotted. The experimental solidus meets the monotectic isotherm at -0.9 at. pct In. The 6/6 + L2 boundary drops steeply to the 6 + La/y + L2 boundary at -1350°C. In this region, it is impossible to detect satisfactory thermal arrests because of the steep phase boundary. The present diagram shows that indium lowers the temperature of the d/y transforma-tion and raises the temperature of the y/a transfor-mation. The y +d region is found to be very narrow. Indium gives rise to a restricted y field when alloyed with iron. The width of this field is between 0.4 and 0.5 at. pct In. Details of the alloys containing 40 and 50 at. pct In have already been reported by the author' and the transformation temperatures of these alloys are included in Fig. 1. It appeared from optical metallography and X-ray diffraction that the room temperature solubility of indium in a iron is less than 0.28 at. pct since alloys of 0.28 at. pct In and above, slow cooled to room temperature, contained dark etching second phase particles situated both in the matrix and grain boundaries of the a-grains, see Figs. 2 and 3. These particles were identified to be unalloyed indium by X-ray diffraction. The lattice parameter of the a phase reached a maximum of 2.8672A at the indium level of -0.28 at. pct. The present diagram, Fig. 1, is in substantial agreement with that of Stadelmaier and Fiedler' except for certain differences in detail. For example, they found the monotectic composition and temperature to be 7.0 at. pct In and 1443oC, respectively, while the present work indicates them to be 3.4 at. pct In and 1470°C. The 6 + L2/y + L2 transformation is indicated in the present work to occur at -1350°C, whereas Stadelmaier and Fiedler find this to occur at -1320°C. They also claim that the width of the y field is 0.2 at. pct In while the present work shows the width to be between 0.4 and 0.5 at. pct In. 1) Indium, when alloyed with iron, gives rise to a restricted y field, the width being >0.5 at. pct In.

Jan 1, 1970

By L. E. Tanner

A study was made of the transformation kinetics of the commercial titanium-base alloys, Ti-2.5Al-16V and Ti-4A1-3Mo-1V, using two different heat treatment cycles: 1) step-quenching to aging temperatures from a ß solution anneal and 2) water-quenching from an a+ß solution anneal followed by reheating to aging temperatures. Metallographic examination and hardness testing provided the major portion of the data, while electrical resistivity, dynamic elastic modulus, and X-ray diffraction techniques were also used to obtain critical or confirnzatory data. TTT diagrams were constructed from these results. The sheet alloys, Ti-2.5Al-16V and Ti-4Al-3Mo-lV, are of current interest to the Department of Defense. As an aid to the planning of their respective heat treatments, a program was carried out to determine the transformation kinetics of these alloys using ß and a + ß reference states. This paper presents the TTT diagrams constructed from data obtained by metallographic examination and hardness testing, as well as by X-ray diffraction, electrical resistivity, and dynamic elastic modulus determinations. EXPERIMENTAL PROCEDURE Materials—Sheets of the alloys were obtained from the producers in the "mill anneal'' condition and were tested prior to shipment to assure their meeting mill specifications. Chemical analyses were also supplied and are presented in Table I. Heat Treatment—The majority of the data presented in this study were obtained from hardness testing and metallographic examination. Sample coupons were cut from the alloy sheets and heat treated on a mass scale. The annealing cycles were operated in the following manner: 1) The ß solution anneals were carried out in a horizontal tube furnace with the bare samples protected by a dynamic helium atmosphere. Following this treatment, the samples were quickly transferred to lead, solder, or oil-bath furnaces for aging. After prescribed times at the various reaction temperatures they were water-quenched. 2) The second cycle simulated commercial practice, which requires the alloys be quenched to room temperature following the a + ß sotution anneal. This anneal was carried out in a muffle furnace with a dynamic helium atmosphere. The specimens were then reheated from room temperature to the reaction temperatures in lead, solder, or oil-bath furnaces, followed by water-quenching after prescribed times at these temperatures. Information concerning the critical temperatures of the alloys was obtained from the literature and solution treatments were based on these values. A summary of the solution annealing treatments is found in Tables II and 111. The aging temperatures for the (a - ß alloys ranged in 50°C intervals from 200°C (392oF) to approximately 50°C below the ß/a + ß transus in the first cycle and approximately 50°C below the a + ß solution temperature in the second. The transformations in these alloys were known to be rather rapid, and thus aging times started at 0.5 min and went to a maximum of 7000 min. Hardness Testing and Metallographic Preparation— Heat-treated samples were sheared and mounted in Bakelite with their cut edges exposed. After a flat surface was ground, the hardness was determined in Vpn on an Armstrong-Vickers machine utilizing a 20-kg load. Three to four impressions were made on each specimen. After this procedure, the hardness impressions were removed and the edge surfaces of the specimens were prepared for metallographic examination in the usual manner. The etchant was 20 pct HF and 20 pct HNO3 in glycerine. Electrical Resistivity—It has been shown that the isothermal reactions in titanium-base alloys can be followed by measuring the changes in e1etrical resistivity attending these transformations. As mentioned earlier, the reaction kinetics of a-ß alloys are rather rapid; thus, it would be expected that resistivity data obtained from these alloys would be more significant if measurements were made continuously at the respective aging temperatures. To accomplish this end a special apparatus, based on the current-potential principle, was assembled. Its design was derived from earlier devices constructed by Colner and zmeska1 4 and Levinson.5 The set-up provided for the heat treatment zof machined specimens (approximately 2 x l0-4in. in cross section by 3 in. in length) and the determination of their relative

Jan 1, 1962

By R. L. McCarron, G. R. Belton

The diffusivities of oxygen and sulfur in liquid iron have heen determined hy a capillary technique in which the surface concentrations of the solutes were established by means of appropriate H2/H2 and H2S/H, gas mixtures. Total diffusate and concentration profile results are shown to be in good accord, yielding for- 1560 and Supporting results at 1660°C are also presented. The conditions necessary to avoid gas transport control in this type of experiment are discussed. IN spite of their importance in understanding the kinetics and mechanisms of refining reactions, the dif-fusivities of oxygen and sulfur in liquid iron are not well established. Accordingly, as a first step in studies of rates of solute absorption from the gas phase into liquid iron, new measurements of these diffusivities have been made and are presented in this paper. The only published results for the diffusion of sulfur in pure liquid iron are those of Kawai.' He used a diffusion couple technique in which two cylindrical specimens, one containing sulfur and the other with negligible sulfur concentration, were joined together and held in a refractory capillary. After an experiment, the sample was quenched and the concentration distribution of the solute determined. Kawai recognized that significant changes in solute distribution occurred during melting and freezing and he attempted to correct the concentration profiles for these effects to give a sulfur diffusivity of 4.6 x 10-6 sq cm per sec at 1560°C. The method of correction, however, was not rigorous and the uncertainty in this result cannot be easily assessed. Koslov et a1.2 have reported the diffusivity of oxygen in iron as 7.8 x 10"3 sq cm per sec at 1660°C. This value appears to be unreasonably high but, unfortunately, details of their experiments are not available. Shurygin and Kryuk have used the rotating disc method for a study of oxygen diffusion in liquid iron. In their experiments a silica disc was rotated in liquid iron containing oxygen, and the rate of formation of liquid iron silicate was determined by measuring the decrease in weight of the disc. On the assumption that the rate of dissolution was controlled by the diffusion of oxygen in the iron, the diffusion coefficient was computed to be 5.2 x sq cm per sec at 1550°C. However, the Levich equation, which was used to interpret the rate data, was originally de- rived for the case of mass transfer between a solid disc and a single-phase liquid. The hydrodynamic and diffusion boundary layers in the iron stirred by a disc, via coupling of the silicate melt, may be appreciably different from those predicted by Levich's equations. Recently, Novokhatskiy and Ershov, using an identical experimental method to that of Shurygin and Kryuk, obtained a diffusivity for oxygen in liquid iron of 1.22 x 104 sq cm per sec at 1550°C: no reasons were offered for the disagreement. Schwerdtfeger5 has also recently studied the diffusivity of oxygen in liquid iron. He reacted shallow melts of liquid iron, 0.5 to 1.0 cm deep and contained in high-purity alumina crucibles, with appropriate H20-HZ-He mixtures. The total sample was analyzed, without sectioning, to obtain the average concentration of diffusate. A value at 1610°C of D = 12(3) x 10-5 sq cm per sec was obtained from the results of twenty experiments.= Oxygen profile measurements, which were carried out in three additional experiments using long capillaries and the semiinfinite boundary conditions, indicated a diffusivity about half that computed from the shallow bath experiments. Possible sources of error in Schwerdtfeger's study will be discussed later in this paper. EXPERIMENTAL TECHNIQUE The essential arrangement of the diffusion cell is shown in Fig. 1. The liquid iron was contained in an alumina capillary, 3 to 4 mm diam and 3 to 9 cm long, which was supported by a hollow alumina pedestal and this whole assembly was held within a movable alumina reaction tube. This tube, which was about 7 mm in bore

Jan 1, 1970

By J. Chipman, N. J. Grant, H. L. Bishop, H. N. Lander

Data of several studies on the equilibrium between molten iron and open hearth-type slags have been combined to determine some of the chemical reactions involved in steel-making. Effects of slag composition and temperature on the iron oxide activity, distribution of sulfur between slag and metal, and the carbon content of the metal are discussed. Also, an overall reaction for the equilibrium between sulfur and oxygen is presented. DURING the past 15 years, a number of significant equilibrium studies have been carried out between liquid iron and simple basic and acid slags in an effort to throw light on the chemical reactions involved in steelmaking. This paper is a summary of the experimental reports on investigations which have been conducted at the Massachusetts Institute of Technology, and of related work in other laboratories. The investigations summarized in this paper include the works of Fetters and Chipman1 and Taylor and Chipman,' which dealt with simple slags that are similar to those found in the open hearth. The sulfur determinations of the slag-metal tests of Fetters and Chipman as reported by Grant and Chip-man" are included. Also, the investigations by Win-kler and Chipman' and Grant and ChipmanQ f more complex slag systems are included in this summary. The experimental procedure is described in detail in each of these papers and will not be discussed. Since the previous reports have been somewhat independent, it is desirable to review and combine the data of the various investigations to determine, as accurately as possible, the reactions in the slag-metal systems of the open hearth. It is the object of this report to present the combined data in such a way as to enhance their utility and applicability. Oxidizing Power of Slags of the System (CaO+MgO)-Si0,-FeO in Equilibrium with Carbon-Free lron The slags selected to determine the iron oxide activity in equilibrium with pure liquid iron were those containing less than 2 pct each of P,O,, MnO, or A1,0, on a weight percentage basis. The method used to calculate activities of iron oxide in liquid slags was that developed by Taylor and Chipman.' The solubility of oxygen in molten carbon-free iron under pure iron oxide slags can be expressed by the following eauation —6320 log (pctO)-------------— + 2.734 [1] where T is the absolute temperature. The oxygen solubility values as determined from Eq. 1 were used throughout this study to calculate the iron oxide activity. The iron oxide activities of slags of various iron oxide contents are plotted in Fig. 1 as a function of the basicity, which is defined as the ratio (pct CaO + pct MgO)/pct SiO,, and are based on molecular percentage values of the components. The percent (FeO), is the total iron content in the slag calculated to FeO. Fig. 1 shows that as the basicity increases at constant mol pct (FeO),, the iron oxide activity increases rapidly and reaches a plateau which extends on the basicity scale from about 1.3 to 2.3; the iron oxide activity then decreases rapidly until a basicity of about 3.0 is reached, where it tends to level off. The solid portions of the curves represent the experimental data of Fetters and Chipman and Win-kler and Chipman. Their experimental heats were made in magnesia crucibles, and hence the slags were saturated with magnesia. The broken lines on the left represent the experimental data of Taylor and Chipman, who used a rotating crucible. In general, these slags contained less than 3 pct MgO. The absence of data for slags containing less than about 40 mol pct (FeO), and basicity ratios greater than about 2.5 made it necessary to calculate curves using ionic concepts of slags. The broken lines on the right, which disregard the solubility limits of di and tricalcium silicate and lime, were obtained by following the treatment of Flood and Grjotheim,"

Jan 1, 1957

By A. K. Mukherjee, John E. Dorn

The effects of strain rate and temperature on the critical resolved shear stress for (321)[111] slip were determined for the silver-rich CsCl type of intermetallic compound AgMg. The flow stress increased only slightly as the test temperature was first decreased below room temperature; a rapid increase in the flow stress was obtained with yet further decrease in temperature from about 250' to 4OK. The effect of both the temperature and strain rate on the flow stress over the low-temperature range could be rationalized satisfactorily in terms of the Peiwls mechanism when the deformation was controlled by rate of nucleation of pairs of kinks. IN spite of the well-documented interest of metallurgists and engineers concerning the mechanical behavior of intermediate phases and intermetallic compounds, very little definitive information is available on this important subject. As recently summarized by westbrook,1 only limited and modest progress has been made thus far in elucidating the details of the mechanism of plastic deformation for the intermetallic compounds; the available information largely concerns phenom-enological descriptions of empirical observations and experimental facts, principally with reference to poly crystalline aggregates. The present report on the elucidation of the rate-controlling mechanism for slip in the bcc structure of AgMg is part of the comprehensive program of a systematic investigation on the mechanical behavior of intermetallic compounds. The intermetallic compound AgMg has a CsCl type of lattice structureZ and is completely ordered up to its melting point of 820c3 This material was selected for our present investigation because of its simple crystal structure, moderate and congruent melting point, ordered structure persisting up to the melting point, and some solubilities of the constituent elements, which could be expected to help in the growing of single-crystal specimens. Whereas previous investigations on the properties of AgMg include hardness,*"6 slip systems,7 tensile flow stress of polycrystalline specimens,' and electrical resistivity,4 the current investigation will be directed principally at elucidating the rate-controlling dislocation mechanism responsible for slip in single crystals at low temperatures. It will be shown that the strain rate is consistent with a model involving the rate of nucleation of pairs of kinks by the Peierls mechanism for plastic deformation. EXPERIMENTAL TECHNIQUES Single-crystal specimens of the AgMg intermetallic compound were prepared and tested as follows: 1) A master alloy ingot of AgMg was produced by melting and chill casting the high-purity silver (99.995 wt pct) and high-purity magnesium (99.997 wt pct) in an induction furnace under a helium atmosphere. 2) Sections of the above-mentioned ingot were placed in a graphite mold containing a spherical cavity in which a single-crystal sphere of 1 in. diam was grown under helium by the Bridgman technique. 3) The operative slip systems were investigated at room temperature on a singlecrystal of AgMg, from measurements of the angles made by the slip traces on the two surfaces of the specimen, which were at 90 deg to each other. The investigation confirmed that the AgMg compound undergoes slip primarily in the (321) plane and in the [Ill] direction, but a small amount of secondary slip was also noticed in the (112) (111) system. No slip was observed in the (110) planes. 4) The single-crystal sphere, mentioned earlier, was oriented in a graphite mold containing a cylindrical cavity of 3/8 in. diam above the spherical receptable to give the angle xo = 45 deg between the axis of the cylindrical bar and the normal to the slip plane (321), and the angle AO = 45 deg between the slip direction [Ill] and the axis of the bar. Oriented single-crystal bar seeds were produced by melting, under a helium atmosphere, a polycrystalline bar in the cylindrical cavity above the oriented spherical seed and by growing an oriented single-crystal bar from the seed. 5) Finally, oriented single-crystal specimens were grown from these cylindrical seeds. 6) The cylindrical specimens were machined in a High-Tension Spark Cutting unit to give a 2-in. gage length. The spark-machined gage section was elec-tropolished in a bath containing 200 ml of H3PO4,

Jan 1, 1964

By K. I. Savage, S. C. Sun

This paper describes a process developed to recover coal, clays and pyrite from coal wastes. The process consists of fine grinding followed by coal and pyrite flotation which leaves the clays in the flotation pulp. A bituminous coal refuse containing 10% sulfur and 30% carbonaceous material was treated by this method to yield a coal product containing 4% sulfur, 10% ash; a pyrite product containing 45% sulfur (84% FeS2), 1% carbonaceous material; and a clay product containing 2% sulfur (3.5% FeS2). The coal yield was about 89%. The pyrite yield was about 77%. The process steps may be entirely flotation, or gravity separation (hydrocycloning) may be used to increase the pyrite : coal ratio in the flotation feed. Cost estimates for the process show a profit of $2.28 per ton of low pyrite grade refuse, but these do not include labor, maintenance, overhead and plant depreciation. The development of this process consisted of three parts: (1) exploratory tests, (2) op-timazation tests and (3) confirmatory tests. The objectionable qualities that sulfur imparts to coal have been commented upon from early times, and they have become more objectionable as the uses of coal have grown. In whatever form coal takes — raw, carbonized or gasified —the sulfur content remains objectionable, and therefore its compounds are removed as completely as possible. It has long been known that sulfur occurs in coal in different forms. In 1861, sulfur was said to exist in the state of sulfuric acid in combination with a base; in combination with iron as iron pyrites; as bisulfides of iron; and in combination with the organic elements of coal.' Pyritic sulfur is a term loosely used to cover the sulfur associated with iron in its various forms. The mineralogically recognized forms are pyrite (FeS2), pyrrhotite (Fe 1-x S) and marcasite (FeS2). The particle sizes of pyrites vary widely. Isolated grains of marcasite smaller than 15 microns have been found disseminated through coal.2 Hair-like "veins" of pyrite filling cracks in vitrain have been found. At the other extreme, lumps or nodules of pyrites large enough for removal by hand picking have been encountered. Organic sulfur, unlike pyritic sulfur, does not exist as discrete particles, but is instead intimately associated with the coal structure and thus it is impossible to remove it or reduce its concentration by physical or mechanical means.2 In the preparation of coal for its various markets, the pyrite minerals (pyrites) are separated from the raw coal feed. This separation process concentrates the pyrites in the tailings or other waste products. It would be desirable to recover these pyrites for three reasons: (1) Pyrites are potential sources of sulfur and iron. In 1967, for the fifth consecutive year, Free World consumption of sulfur exceeded production.3 Propelled by the shortage, the domestic price of sulfur has risen from $24 to $38 per long ton (bright). (2) The refuse, when placed in piles, becomes ignited. The pyrites (FeS2) bum, giving off SO,. Thus, the pyrites are a cause of air pollution. (3) Also, the pyrites undergo chemical reaction when exposed to air. The refuse is leached by waters which result in stream pollution due to the water-soluble iron and acidic reaction products. Coal refuse also contains coal minerals and clay minerals. Therefore, any process for recovering the pyrites must successfully separate them from the coal and clay minerals. In the study discussed here, ten different bituminous coal refuse samples were successfully upgraded in pyrite content. These samples represented a wide variety of coal waste materials from Pennsylvania and other states. The variabilities of the sulfur and coal contents are shown in Table I. The extremes are Sample J, a high sulfur-low coal, and Sample B, a low sulfur-high coal. Definitions of some of the symbols or terms used in this report are given below: Mesh size—Tyler standard mesh screen sieves with an opening based on the square root of two. Fe —Indicates iron, as determined by a stannous reduction-dichromatic oxidation method. S—Indicates sulfur, as determined by the ASTM "Eschka" method for sulfur in coal.

Jan 1, 1969

By W. F. Hower, W. Brown

Large-scale sand consolidation tests were conducted in an effort to determine the reasons for the successes and failures of this method of sand control. Several different consolidating materials were used in treating both clean and bentonitic sands that were packed in a chamber having a capacity of 3.3 cu ft. The results were essentially the same for all of the different consolidating materials, The data show that low-viscosity consolidating materials pumped at a relatively slow rate gave the best results. Where the formation has produced sand, the treating fluids can compress the formation, thus permitting the channeling of fluids to another horizon. Pressure-packing these zones before attempting to consolidate is recommended. Sands containing more than 4 per cent of water-swelling clays are not good candidates for consolidation. It is indicated that loose sand, particularly when it is bentonitic, can be fractured during the placement of the treating fluids. INTRODUCTION Sand production in oil and gas wells has plagued the industry for many years, and numerous cures for this problem have been suggested. Most methods have been successful to a certain degree, but the great variety of well conditions that exist in the different areas has magni- fied the problem and limited the successful use of the various systems. Four review papers1-4 present a wealth of information concerning the degrees of success that have been obtained by the different sand-control methods. The bridging of sand grains by the use of gravel packs and screens has been quite successful. However, these methods do not leave the casing clear for all types of multiple completions, and the cure does not last for the production life of the well in some instance:;. The control of loose sands by sand consolidation with resins has never been as successful as desired. It has always been hoped that such a treatment would eliminate all sand problems for the life of the well, but. initial applications, starting in the middle 1940's, were only moderately successful. Lott, et a1,3 reported a success ratio of approximately 50 per cent and made the following conclusions. The highest percentage of successes were obtained where: a. Consolidation of a zone was made at the time of initial completion or prior to the production of sand. b. The interval treated was less than 12 ft in length. c. Between 30 and 50 gill plastic/ft of producing interval was displaced through the perforations. REASONS FOR SAND CONSOLIDATION FAILURES Our own experiences in the field of sand consolidation point toward the following conditions as the major reasons for the failure of sand consolidation attempts. 1. Mud-plugged perforations and mud invasion of the formation. 2. Sand in the casing covering all or part of the perforations. This sand could be either formation sand or one of the coarser sands used as propping agents in hydraulic fracturing. 3. Holes in the casing. 4. Channels behind the casing. 5. Attempting to treat too long a perforated section. 6. Too high a percentage of water-swelling clays in the formation. 7. Formations that have produced sand. Recent attempts were made to treat perforated sections ranging from 10 to 30 ft, in wells that have produced sand, by using a straddle packer that was raised and lowered through the perforations as the consolidating material was being pumped. In most instances, the pressure required to pump fluid into the formation varied considerably as the tool was raised and lowered. This suggested the possibility that significant differences in permeability were present or that only part of the formation had produced sand. There were times when a sudden break in pressure indicated that a fracture was being formed. Research conducted several years ago concerning the problem of the control of water in air and gas drilling indicated that shale sections could be fractured quite easily. In addition, it was determined that it was easier to pump fluids into shale bodies by fracturing the shale itself, or the interface between the shale and sand, than to pump into a fluid-saturated formation. Formations that produce sand are usually adjacent to shale bodies and frequently have shale streaks of various thicknesses inter-bedded in the sand. Therefore, where shale is exposed to fluid pressure it

By Y. Shimomura, M. Serizawa, Y. Takahashi, K. Miyagawa

The "semi-pellet" sintering method developed and currently being used at the Fuji Iron & Steel's Hirohata Works is discusssd. It is shown that the method makes fine-sized material easily sinterable and increases sinter production. The operation can be incorporated readily into conventional sintering plants. Sintering plant raw materials currently being used in the Hirohata Works consist of 40 pct pyrite cinder, 40 pct fines resulting from crushing and screening of imported ores, and 20 pct others, such as mill scale and iron sands. Pyrite cinder, a major component in the sinter feed, has been getting finer since 1952, due to the increased grinding required for the improvement of the results in the iron sulfide flotation and to the adoption of FluoSolid roasters in sul-furic acid plants; some fines pass 100-mesh sieve almost completely. Increased use of the fine-sized pyrite cinders in the sinter raw mix resulted in such difficulties as decreased bed permeability, uneven firing conditions, and low yield. In an attempt to study the cause and to find a remedy for this problem, a series of experiments were made, using an 80-kg experimental sintering pan. As a result it was established that, by rolling the fine-sized pyrite cinders into small balls of 10 to 3 mm diam (hereafter called semi-pellets) and mixing them into the sinter raw mix, the bed permeability was improved, the sintering time shortened, and the yield and production rate increased. It is proposed that this new method be called the semi-pellet sintem'ng. In recent years the pelletizing process has taken the spotlight in the agglomeration field for treating fine-sized ores here in Japan as well as in the U.S. and Europe. This process produces pellets suitable for the blast furnace charge as such, and consists of three major operations: fine grinding, balling, and firing. With regard to the firing technique, some problems still appear unsolved. In the semi-pellet sintering, however, several ad- vantages can be claimed: the balling operation is relatively simple because only small-sized balls are shown to be acceptable and the operation can be readily incorporated into the conventional sintering plant, since only balling, not grinding or firing, equipment is needed. Basic test work on the process was initiated in 1954 and favorable results were obtained. Accordingly a pilot plant was built in 1955 and the test work was continued. The semi-pellets thus prepared in the pilot plant were tested further by USing them in the actual sintering pan and their beneficial effects ascertained. In late 1956 a drum-type balling machine (2.4X4 m) was installed and it went into operation in April 1957 in conjunction with the Greenawalt sintering plant (8 pans having dimensions of 7.2 m in length, 3 m in width, and 0.3 m in depth). In October 1958 a cone-type pelletizer, with a 2.2 m diam, and later a disk-type pelletizer were further added in the plant. In the DL sintering plant (2000 tpd), newly built in July, 1960, four disk-type pelletizers (3.2 m diam, 10 tph capacity) were installed. By mixing the semi-pellets thus prepared with the feed, the sintering operation was found to be greatly improved. The results of the basic test work, and the equipment and operation of the semi-pellet sintering operation at the Hirohata Works will be described. ON THE SINTERING CHARACTERISTICS OF FINE SIZED PYRITE CINDERS To ascertain the effect of addition of fine-sized pyrite cinders on the sintering characteristics, a series of measurements on bed permeability was carried out by varying the size distribution of pyrite cinders. The composition of the raw mix used in the tests was fixed at 50 pct pyrite cinder, 20 pct Larap magnetite fines, 30 pct sinter return, and 5 pct coke; only the size distribution of the pyrite cinder was varied. Also the moisture content was changed at each size distribution. The results are given in Fig. 1. For all pyrite cinders tested the bed

Jan 1, 1961

By C. E. Kemp, A. B. Dyes

Results of a field research project on the thermal recovery of oil by movement of a combustion front are presented. This field test was conducted in the South Belridge field, This The war paitern was a Southsing1e 2.5-acre five-spot pattern in the 700-ft deep Tulare sand. Results of this project indicate the technical feasibility of producing high viscosity, low-grallity crude oils by thermal means. It was demonstrated that heavy oils could be moved rapidly over considerable distances by thermal drive, and that high percentage recoveries of oil could be effected. The bulk of the oil recovery came after arrival of the burning front at a production well. However, rapid corrosion and high-temperature failure of conventional pipe and equipment both below and above surface occurred. Stainless steels gave more satisfectory performance under these conditions than did conventional steels. Oxygen was seldom observed in gas from wells ahead of the burning front, and it appears that the front was continuous throughout the life of the experiment. INTRODUCTION During late 1953 and early 1954, industry-wide attention was focused on the thermal recovery of oil by movement of a combustion front through an oil zone. Two separate Oklahoma field tests were described in publications by Kuhn and Koch, and Grant and Szasz. To obtain basic information needed for making engineering and economic appraisals of commercial recovery of heavy oil by this thermal recovery method, a new field research projecta3,4 was started May 31, 1955. Twelve oil companies contributed to this project with General Petroleum Corp. as operator. Since combustion recovery experiments* with heavy oils in other areas had been conducted in small patterns,"' an important purpose of this test was to determine whether the process could be operated in a pattern of near-commercial well spacing. The south Belridge field, located 30 miles north of Taft, Calif., was chosen because its oil sands are similar to many heavy oil sands which typically have low primary recovery and leave a large amount of oil in place. such fields are not particularly suited for common secondary recovery methods. DESCRIPTION OF TEST SITE The test interval was a Tulare sand at a depth of about 700 ft. Nine test wells were drilled, cored and completed from Oct., 1955, through Jan., 1956. The initial pattern shown on the map, Fig. 1, consisted of an injection well (II)', four producing wells (1P-4P), and four observation wells (IT-4T). An old well (81) was also recompleted for use as an observation well. The area enclosed by the original four production wells was 2.5 acres; the distance from the injection well to each production well was 233 ft. During the combustion period, Well 5P was drilled to replace Well 2P, and Well 6P was drilled to replace Well 3P. The new wells were 25 ft beyond the old production wells along a diagonal from the injection well, and resulted in an increase in pattern area to 2.75 acres. Isopachs are shown in Fig. 1. The average thickness of the oil sand in the test pattern was 30 ft. Fig. 2 presents two cross sections through the test pattern. Oil sand is represented by white and claystone by gray. The dashed lines indicate layers of conglomerate grading to claystone. The sand thickness was fairly uniform throughout the test pattern except in the 1P area. The sand body dips gently from the northwest to southeast, about 3 degrees from horizontal. The sand is unconsoli-dated, and grades from very fine material to pebbles as large as 2 in. in diameter. Table 1 presents the average initial properties of the formation. The in-place porosity of 37 per cent was estimated from the porosity of coke-consolidated cores taken after combustion. Original core analyses data were adjusted to 37 per cent, giving pore volume saturations of 60 per cent oil, 37 per cent water, and 3 per

By R. G. Ward, A. E. El-Mehairy

A technique was developed to calculate the density of liquid metals from the profile of a weighed levitated drop obtained by emitted light photography and calibration. The density of liquid copper was determined over the temperature range 1370" to 2100°K and expressed with the equation: The molar volumes and thermal coefficients of expansion are calculated. Copper, upon melting, was found to expand 3.34 pct. A knowledge of the density of liquid metals is essential as it is a parameter appearing in most theories of the liquid state. The liquid density is also necessary for the calculation of the commercially important contraction occurring on solidification. Unfortunately good density values are rarely available and the present work was undertaken to establish a new method of density determination free from the limitations of the existing methods. For liquid metals with high melting points, the variation and the limited number of density values reported in the literature have been caused primarily by difficulties in technique, a matter which has been adequately discussed by Urbain.' In all the methods used for measuring the density of the high-melting liquid metals there are sources of error, and corrections have to be made. For example, in the method of balanced columns, the formation of gas bubbles in one or both arms was a great source of error. In the pyknometer3 and immersed-sinker methods, corrections of certain volumes for thermal expansion to the operating temperature exceed 4 pct. In the maximum-bubble method5 a correction for the thermal expansion of the bubble-tube is used (about 1.6 pct); a second correction takes into account the change in the volume of liquid displaced by the bubble-tube (about 3.5 pct). Another method used is based on the shape of a drop of liquid, at rest on an inert refractory plaque, obtained photographically or radiographi-cally. The volume is calculated from the shape, which is sensitive to the surface tension and supporting material, by some intricate empirical relation. The drop contour changes with 90 deg rotation of the support.7 The application of all methods is limited by reaction between liquid metal and the apparatus. The successful stabilization of a mass of liquid metal during levitation melting8 afforded a technique for measuring the density of liquid metals out of contact with solid materials. The technique was developed by using copper as the density of liquid copper has already been studied extensively, thus allowing comparison with the new method. It consists of calculating the volume from the dimensioned profile of the levitated drop obtained by emitted-light photography and careful calibration. The molten egg-shaped drop spins around the magnetic axis of the coil (lined vertically) at a speed which seems to increase with increasing temperature. The method does not involve corrections and the experimental setup allows the use of vacuum or special atmospheres. The maximum operating temperature is limited by excessive evaporation of metal from the droplet. EXPERIMENTAL Levitating System. A stabilizing ring was used in conjunction with a 3-turn levitating coil energized by a 450-kc per sec, 10-kw Toccotron with a high current-low voltage output stabilized to f 1 pet.' APyrex glass tube with a Pyrex Optical flat window inserted through the coil and ring allowed the use of special atmospheres during levitation melting, as shown in Fig. 1. Optical System. Fig. 1 shows the optical arrangement used to photograph the profiles of the drop, parallel and perpendicular to the vertical spinning axis, simultaneously on the same frame of a high-speed 35-mm film. The optical system was adjusted to avoid any distortion of the profiles and to ensure that both profiles are in focus. The length of path from object to objective was about 30 cm, and a magnification factor close to 1 was obtained with the single-lens reflex-camera system. Temperature Measurement and Control. In operation, the specimen temperature was constant to 5 C for a fixed power input to the levitating coil and fixed rate of gas flow through the tube. The temperature was measured by an automatic two-color pyrometer (Coloratio) checked at the melting

Jan 1, 1963

By G. T. Hahn, C. N. Reid, A. Gilbert

An evaluation is made of the possible cautsal relationship between twinning and fracture in molybdenum. For both single and poly crystalline material no instance of twin-induced fracture was observed. Instead brittle fracture was found to be slip-induced at heterogeneities. For single-crystal material, the yield stvess in compression and the fracture stvess in tensiow obey a similar angular- relationship which follows approximately a 1/cos2 ? law. where 0 is the angle between the specimen axis and the nearest (100) plane. This sittlilarity between yield and fracture behavior casts doubt on the interpretations made previoltsly that a 1/cos2? relationship supports a critical normal fracture stress criterion. SINCE fracture in brittle materials takes place at stresses an order of magnitude lower than the theoretical strength of the lattice, it must be postulated that some stress-concentrating effect is operative during the fracture-initiation process. Several mechanisms have been proposed whereby the necessary stress concentrations could be produced. The well-known Cottrell mechanism1 describes a dislocation interaction which can lead to the formation of an incipient cleavage crack on a cleavage plane, and both zener2 and stroh3 have discussed models which predict the stress concentration at the intersection of a slip band with a grain boundary. When twinning occurs twin/twin intersections and twin/grain boundary intersections represent another possible means of fracture initiation. Although still controversial, the concept of twin-induced fracture is supported by a weighty mass of evidence, which has been reviewed in a recent paper.4 This investigation was conducted in order to assess the extent to which the brittleness of molybdenum can be ascribed to this cause. Emphasis was placed on seeking direct metallographic evidence for twin-induced fracture such as arrangements of twins located at the fracture origin. EXPERIMENTAL PROGRAM Materials. The experimental materials are described inTable I. From the chemical analyses and estimates of the amounts of interstitials likely to be retained in solution,5 it is concluded that all were mul-tiphased systems. X-ray diffraction experiments6 showed no evidence of preferred orientation in the polycrystalline materials. Single crystals were grown from Molybdenum X and Y using the floating-zone technique,' in a vacuum of better than 3 x 10-5 Torr. However difficulties were experienced with Molybdenum X due to violent gas evolution from the molten zone, and additional crystals (Crystals 3 to 6) were produced by annealing for 5 1/2 hr at 2300°C under a vacuum of 10-4 Torr. Techniques. A series of tension, compression, and bend tests was conducted. Tension tests were used to demonstrate brittle behavior, to measure brittle-fracture stresses, and to provide fractured specimens for metallographic inspection. Compression tests were employed in order to obtain some ductility and a measure of the yield stress. Furthermore, it was considered that compression loading would permit the study of crack nucleation in the absence of propagation. The bend tests were conducted to facilitate identification of the fracture origin, which would be expected to be at, or near, the tensile surface of the sample. Tests were carried out at temperatures between 78" and 298°K attained by means of a liquid-nitrogen evaporator of modified Wessel design.' Specimens were fashioned by mechanical grinding, and, prior to heat treatment, were electropolished at 10 v in a 3:l mixture of ethyl alcohol and sulfuric acid, using a stainless-steel cathode. Except where noted, a strain rate of 4 pct per min was used. All specimens had a gage section 0.75 in. long; diameters of 0.10 and 0.20 in. were adopted for the tension and compression specimens, respectively, the former of single shoulder design, the ends being gripped in split collets with a conical bearing surface. In the bend test, electropolished specimens measuring 0.080 by 0.25 by 1.25 in. were deformed at 78°K by four-point loading. The bending device had spans of 1 in. between the outer and 4 in between the inner fulcra; it was stressed between the compression anvils of the Instron machine at a constant deflection rate. EXPERIMENTAL RESULTS Polycrystals. Tension and Compression Tcsls. It is apparent from Fig. 1(a) that above 170°K fracture of Molybdenum X takes place at stresses equal to or greater than the compressive yield stress whereas

Jan 1, 1967

By Kenric C. Owen

INTRODUCTION Situated 23 miles east of Pretoria the Premier Mine started diamond production in 1903. Two years later it produced the largest diamond yet discovered, the 3 106 carat Cullinan stone. For the period to 1932 when the mine was closed down due to economic circumstances, open cast mining was practised using inclined rope haulage traction and by this time had produced 48.5 million carats of predominantly industrial quality diamonds from 148 million tons of ore. In 1945 it was decided to re-open the mine using underground mining methods. A system using long hole benching was devised (Hodgson and Sewel 1960). This system was later modified but still forms the basis for approximately fifty percent of production. Following the successful introduction of block caving on associated diamond mines in the Kimberley area (Gallagher and Loftus 1960) this mining method was introduced to the Premier Mine in the late 60's and now accounts for nearly 50% of production. This paper will discuss block caving at Premier Mine in the light of our experience and discussion will be directed to the main geological and structural features of the orebody and host rocks and the related constraints imposed on the mining methods. Reference is made to the long hole benching mining method for comparative purposes. GENERAL DESCRIPTION OF OPERATIONS The ore from the block caving and bench mining areas gravitates via ore passes to a twin haulage, 500m below surface. Electric 13 tonne locomotives, each hauling a train of 10 Granby type cars, deliver the ore to two 42" x 48" (1.06m x 1.22m) jaw crushers. The ore is reduced in size to minus 0.15m before being hoisted to the treatment plant on surface. Hoisting is done with 12.5 tonne bottom discharge skips in a five compartment rectangular shaft using two 3 240 H.P. semi automatic Ward Leonard winders. A small single drum service winder operates in the other compartment. Men and materials travel in a separate shaft in a 5,4m x 2,8m cage operated by a Koepi winder. These two shafts are also the main intake airways to the mine. The two main extraction fans capable of 250 m3/s at 3,2 kPa are situated on surface and are connected to the underground workings by an incline and a network of air passes and return airways. GEOLOGY Although there are numerous occurrences of kimberlite bodies in the district, the Premier Mine kimberlite pipe is the only economic orebody. It is roughly oval in shape with surface dimensions of 900m on the long axis and 450monthe short axis. The surface area is 320 000 m2. The kimberlite has intruded a massive body of felsite and norite which is intersected by a number of faults. The contact between the kimberlite and host rock is clear cut and dips inward at an average angle of 80°. Cutting across the pipe and the country rock is a 75 metre thick gabbro sill, the top of which intersects the pipe below the 347m level and dips at 15' to the north west. The kimberlite has been metamorphosed a distance of some 20m both above and below the sill contacts. Age measurements on biotite from the gabbro date the sill as 1 115 million years, thereby providing a minimum age of the pipe. (Pre Cambrian). All other pipes in South Africa are of Cretaceous age (60 million years). A simplified geological plan and section of the Premier Mine orebody is shown in Figure 1. It is thought that the kimberlite intruded in at least three distinct phases. The kimberlites of these different phases can be distinguished most easily by their characteristic colour. BROWN KIMBERLITE. This is the oldest kimberlite and forms a crescent shape in plan on the south eastern side of the pipe. In depth it increases in relative area. Although the brown kimberlite carries the highest diamond grade in terms of carats per ton all the various kimberlites in the Premier pipe are economic to mine.

Jan 1, 1981

By R. Simon, D. J. Graue

This paper presents correlations for predicting the solu-lility, swelling and viscosity behavior of CO2-crude oil sys8i.m~. The correlations were developed from experimental data obtained by the authors. These data are also presented. The data were determined by measuring the properties of mixtures of CO, and nine different oils. Experiinental conditions covered a range of 100 to 250°F and pressures up to 2,300 psia. Properties predicted by the correlations have average deviations, expressed as per cent of experimental value, of 2 per cent for solubility, 0.5 per cent for swelling and 12 per cent for viscosity. INTRODUCTION Interest in CO2 injection as an oil recovery process has led to the development of performance prediction methods which can be applied to specific reservoirs.1 iS To use these performance prediction methods, it is necessary to know the solubility, swelling and viscosity properties of CO2-crude oil mixtures at reservoir conditions. Some information on these properties has appeared in the literature; however, this information did not cover the range of different oils and conditions needed to prepare generalized correlations for reservoir engineering purposes. Consequently, an experimental program was undertaken to collect the data needed. The data obtained and the correlations developed from the data are described in the following sections of this paper. SOLUBILITY OF CO2 IN CRUDE OILS CO2 solubility data in the literature come from six principal sources. The solubility prediction method of Welker and Dunlop3 is limited to 80F. The information in Ref. 4 is of two types: the first includes binary and ternary mixtures of CO, and light hydrocarbons (C1 to C6), and the second gives data for CO1 and heavy hydrocarbons for a temperature range of 40 to 90F. Ref. 5 contains a KCO2 chart for systems whose convergence pressure is 4,000 psia. The KCO2's are based mainly on CO2-natural gas mixtures. Poettmann's work covered CO2 solubility in one condensate and one crude oil6,7 Ja-coby and Rzasa measured CO? solubilities as a function of pressure and temperature for two natural gas-absorber oil mixtures and two natural gas-crude oil mixtures.'8 CO, concentration in these four systems was fixed at 5 mol per cent. The work reported in this paper extends CO, solubility data to a variety of different crude oil types in a temperature range from 110 to 250F and pressures up to 2,300 psia. The experimental procedure used by the authors to obtain the solubility data consisted of combining known amounts of pure CO, and crude oil in a visual cell at a fixed temperature and measuring the bubble point of the mixture. Measurements were made for a total of 40 different CO2-oil mixtures and the results are shown in Table 2. The mixtures included nine different oils (seven crude oils and two refined oils) whose properties are listed in Table 1. All nine oils had vapor pressures less than 1 atm at the experimental temperatures. Consequently, analysis of the bubble-point vapor showed a CO, concentration over 99 mol per cent. At no time during these experiments was a second, more dense, liquid phase observed. The solubility correlation which was developed from the data in Table 2 is presented in Figs. 1, 2 and 3. In these figures, solubility is expressed as xco2 the mol fraction of CO, in the CO2-oil mixture. Fig. 1 shows solubility as a function of CO2 fugacity6 and temperature. Fig. 2 shows the same solubility data expressed as a function of saturation pressure and temperature. The solubility shown in Figs. 1 and 2 is for an oil whose UOP characterization factor is 11.7. UOP characterization factors of crude oils can be determined from Ref. 10 if the viscosity and APT gravity of the oil are known. Fig. 3 gives the solubility correction factor for oils whose UOP characterization factors differ from 11.7. The solubility correlation in Figs. 1, 2 and 3 predicted

Jan 1, 1966

By Jun Hino, P. G. Shewmon, P. A. Beck

THE investigations of Crussard,' of Guinier and Tennevin,' and of Dunn and Daniels," indicate that the subgrains formed in a cold worked and annealed metal are capable of growing at each other's expense during annealing, if the temperature of annealing is sufficiently high and the time is long enough. The results of Dunn and Daniels are particularly convincing in showing that subgrain growth is essentially the result of the free surface energy associated with the subboundaries. In subgrain growth, as in ordinary grain growth, energy is gained as a result of the decrease in total subboundary surface area per unit volume. Recently, Wood and Scrutton4 found that the rate of subgrain growth upon annealing increased very considerably, if simultaneously a creep strain was applied to the specimen at a low strain rate. Working with 99.98 pct pure fine-grained aluminum, these investigators found that the continuous X-ray diffraction back-reflection rings of material strained at room temperature remained continuous after heating for ten days at 250 °C. However, when heated at the same temperature under a stress of 1000 psi even for only three days, the formerly continuous X-ray diffraction rings broke up into numerous dots, which were fairly clearly separated from each other. The continuous X-ray diffraction rings were interpreted as indications of a very small subgrain size, not resolved by the X-ray diffraction method used. The breaking up of the continuous X-ray diffraction ring during annealing under stress was taken as an indication of a great increase in subgrain size, so that the individual subgrains could then be resolved. The effect of simultaneous strain at a low strain rate in accelerating subgrain growth, discovered by Wood and Scrutton and designated by them as "cell growth," is of fundamental importance. The experiments described in this note were carried out in order to confirm Wood and Scrutton's results by direct metallographic observation. Also, information was sought as to the minimum creep strain necessary to produce this effect. A fine grained high purity aluminum strip was prepared by alternate 33 pct rolling and annealing treatments for 1 hr at 350°C. Specimens cut from this strip were subjected to a relatively fast creep strain of 7.2 pct in 3.5 min at 300°C under a constant load initially corresponding to 1185 psi. The subgrains set up were large enough (about 0.015 to 0.03 mm) to be clearly observed (Fig. 1) at X200 magnification with polarized light, after electrolytic polishing and anodic etching, producing a fine oxide film." The corresponding X-ray diffraction pattern is shown in Fig. la. After the fast creep strain treatment a portion of the specimen was subjected to a creep strain of 8.3 pct in 44 hr at 350°C under a constant load initially corresponding to 320 psi. Another portion, annealed under the same conditions, but not strained, served as control specimen. The subgrain size of a typical area of the specimen annealed under strain and of the one annealed without strain is shown in Figs. 2 and 3 (X-ray diffraction patterns, Figs. 2a and 3a). Annealing without strain produced clearly observable subgrain growth (subgrain size: about 0.03 to 0.05 mm). The effect of simultaneous strain was to increase greatly the rate of subgrain growth (resulting in a subgrain size of approximately 0.05 to 0.13 mm), in accordance with Wood and Scrutton. In another experiment, the effect of the amount of simultaneous strain was studied. The initial subgrain structure was set up by fast creep, as described previously. The specimen was then heated at 350 °C under a constant load initially corresponding to 320 psi, as above, for 2.2 hr (0.24 pct strain), and 8.8 hr (0.58 pct strain). Comparison with the corresponding unstrained control specimens by means of X-ray diffraction showed that 0.58 pct strain definitely had an effect, but the effect of 0.24 pct strain was doubtful.

Jan 1, 1953

By R. Q. Shotts

Nitric acid oxidation rate analyses of three coals, previously studied microscopically by the Bureau of Mines, revealed three components. Relative quantities agree with those found for the four components given by the Bureau and results are consistent with current ideas of coal constitution. Possible multi-component composition for bright coal and a reactivity-rank relation are suggested. THE physically dissimilar components of bituminous coals often are easily recognized mega-scopically. Under the microscope, reflected light or light transmitted through thin sections reveals the presence of the different components, even when these are intimately mixed. Optical methods for the quantitative estimation of the relative abundance of the various components, both by means of thin sections and by particle count, have been fully described.'. ' It has long been recognized that there are chemical and physical differences between the various petro-graphic components of bituminous coals, although analytical differences usually are small.:'. ' Only in the case of fusain have chemical differences been used for quantitative determination of a component. C. C. Hsiao and associates, at the Mineral Industries Experiment Station of the Pennsylvania State College, have described a method of analysis which is based upon the differences in the rate of nitric acid (8N) oxidation, fusain, and the other components of coal."," The reproducibility of their method and its applicability in checking microscopic determinations of fusain content have been supported by several independent investigations.'. " The writer has proposed the use of differences in oxidizability for the estimation of other components." "' The results of the oxidation of whole coals and of float-and-sink fractions of coals were reported. In most cases the plots of the logarithms of the percent dry, non-fusain, organic residue from oxidation, against time, revealed the presence of at least two distinct components. Both components appeared to oxidize according to a first order law, but the reaction constants for the components were distinctly different. One or more of the dull density fractions were found to contain but one component, and some of the lower rank coals oxidized in such a way as to suggest the presence of three components. A suitable way to check the identity and significance of the components delineated by oxidation would be to analyze a sample of coal both by the nitric acid oxidation procedure and by a microscopic method. The writer was wholly unfamiliar with either of the microscopic techniques commonly used, and to make such a comparison it was necessary to rely upon microscopic analyses made by someone else. It is hoped that some laboratory which is equipped to make both types of analyses will some day make them upon identical samples. During the past 20 years, four Alabama coals have been analyzed petrographically and the results published by the United States Bureau of Mines. They are: 1—Flat Top mine, Mary Lee bed; 2—Empire mine, Black Creek bed; 3—Wylam No. 8 mine, Pratt bed, all in the Warrior field; and 4—Soot Creek mine, Fairview bed, in the Coosa field."-" Of these, only the Flat Top mine is still operating. Because of the closing of these mines, it first appeared necessary to rely upon the indirect and unsatisfactory procedure of sampling the beds in other mines located as near to the closed mines as possible. Upon investigation, however, it was found that the Bureau of Mines still had, in storage, the very same samples which had been used in the published petrographic studies. The Bureau very generously furnished about 2000 g each of the Pratt, Mary Lee, and Fairview bed coals, largely lumps but with some fines. The blocks of coal, when received, still were covered by the paraffin coating which had been placed on the polished surface, in the case of the Mary Lee coal almost twenty years ago. Procedure The procedure for oxidizing the coal sample and removing the alkali-soluble humic acid has been described. In the present study, oxidation periods of 1/6, 1/3, 1/2, 3/4, 1, 2, 3, and 4 hr were used. All oxidations were made in triplicate. After the paraffin had been removed in boiling water and the coal washed carefully with cold benzene, the entire sample of approximately 2000 g, obtained from the Bureau of Mines, was crushed to pass a No. 4 sieve. About 200 g of this material was pulverized to pass

Jan 1, 1954

By C. D. Allman

Specifications for coal at the Grand Lake thermal electric station read in part: "Coal will be Rom Minto Bituminous (strip operation). Maximum lump 3x3x4 ft. Very corrosive, abrasive and when damp, sticky. Coal may consist of frozen lumps of coal, snow and ice." To maintain quality control it was necessary to develop an automatic sampling system capable of: 1) sampling from one 10-ton truckload every 1½ min; 2) permitting an operator to automatically take a sample from each truckload; 3) depositing the sample in a pre-selected container, one of a possible 10; and 4) performing the sampling operations in accordance with latest ASTM specifications for sampling coal with an ash content of 35%. This paper tells how these and other problems were resolved and describes the equipment used. The New Brunswick Electric Power Commission issued detailed specification No. 5351-5009 outlining the scope of work and general requirements for a mechanical coal handling system to be installed at the Commissions Grand Lake Generating Station. The thermal station is located at Newcastle Creek, some 40 miles east of Fredericton, N.B. Canada, on the shore of Grand Lake. This particular location is immediately adjacent to the Minto strip mining coal area of New Brunswick. Contained in the specifications, but not detailed specifically was an automatic coal sampling system. The system outlined, was to be designed and specified by the individual equipment tenderers. In conjunction with the Hardinge Co., the Barber-Greene Co. designed a sampling system which was contained in the general contract proposal. The system as designed originally, however, presented certain limitations to a continuous coal handling system and was ultimately changed. However, it was only through preliminary study and design that problems created by the specifications were determined, and these problems discussed and finally negotiated with the NBEPC engineering staff created the subsequent sampling system now being installed by Barber-Greene. It must be considered that where the original specifications did not detail the mechanical equipment, it was necessary to present a system which would correspond to the intent of specification and for which Barber-Greene would be responsible as to function, but remain in a competitive position with regard to the tender considered primarily on a price basis. The system now being installed, contains basically all the components which were detailed originally, with the exception of the holding bin arrangement, which was changed to allow a continuous operation of the entire coal handling system. SPECIFICATIONS The specifications covering the sampling system follow. 4.5 Sampler: An automatic sampling system shall be installed capable of sampling one-truck load of coal every 1½ min. When the coal is dumped into the receiving hopper, the operator shall push a button and the sampler shall automatically take a sample of that particular coal when it reaches the sampler. Then the sample taken shall be crushed and reduced in quantity to a workable sample and deposited in a pre-selected container, one of a possible ten. All samples and sampling operations shall be in accordance with the latest edition of ASTM designation 492 for sampling coal with an ash content of 35%. The coal for the initial sample shall have maximum sized lumps of about 3/4 in. and the final sample shall be adjustable from 2 to 5 lb per sample and capable of passing through a sieve with 1/8-in. diam openings. It should be noted that, because of the time delay between the time the sample is requested and when it is actually taken, the operator may call for one or two additional samples from different coal before the first sample is completely refined and in the final sample can. Coal is received from a number of different suppliers on the same day, therefore, the system shall be designed so that there is no possibility of mixing or contaminating the coal from the different suppliers. All coal rejected from the sample shall be returned to the main conveyor. All chutes, hoppers, etc. shall be designed in accordance with Section 4.6 of these specifications. 4.6 Chutes, Hoppers, etc. All chutes and hoppers

Jan 1, 1963

By G. S. Tint, M. Herman, V. V. Damiano

Dislocation arrays and substructures were studied in cadmium doped zinc crystals using a newly devised etching technique. Cadmium precipitates delineating the dislocations were revealed by etching a surface closely parallel to the (0001) slip plane. Cinephotomicrography of the continuous etching process revealed the three-dimensional aspects of dislocations in the bulk crystal. Dislocation etch patterns were studied in both deformed and annealed crystals after suitable aging at room temperature. The effect of annealing was evidenced by a rearrangement of the dislocations into low-angle boundaries and hexagonal networks. ETCH pit techniques have been used extensively to study dislocations in both deformed and annealed bulk metal crystals. Ideally one hopes to obtain a one-to-one correspondence between the etch pits and the points of emergence of the dislocations at the surface. One then attempts to deduce the way in which dislocations are arranged in the bulk crystal from the arrangement of etch pits on the surface. It is clear that one can obtain only limited information of the dislocation configurations inside the crystal from etch pit studies of single surfaces. Considerably more information is obtained if one is able to follow the course of the dislocations through the crystal using progressive etching technique. Techniques of this sort were used by Gilmanl to study dislocations on the slip planes of NaCl crystals and by Damiano and Tint2 to study dislocation arrangement in zinc crystals grown from the melt. The present paper makes use of a technique first described by Tint and Damiano3 to observe and continuously record the dislocation structures which appear while a crystal surface was being progressively etched. Studies were made on cleaved (0001) surfaces to reveal the dislocations along their length on the surface closely parallel to the slip plane. The technique for revealing segments of dislocations along their length by etching is well known. Wilsdorf and Kuhlmann-wilsdorf4 revealed disloca- tions along their length in aluminum containing a few percent copper, when precipitates segregated along the dislocations. The technique was used by Low and Guard5 to study dislocation configurations on the slip plane in Fe-Si alloys containing carbon. In the present work the technique was applied to zinc containing cadmium since it was shown by Gil-man6 that a cadmium-rich phase could be made to precipitate from supersaturated solutions along dislocations in zinc. Segments of dislocations delineated by the precipitates were revealed by etching a surface prepared by cleaving the crystal. The three-dimensional nature of dislocations and substructures was thus studied from the cinephotomicro-graphic record of the continuous etching process. EXPERIMENTAL Single crystals of zinc containing the order of 0.1 pct Cd were prepared by slowly lowering a graphite crucible containing the melt through a temperature gradient of 15°C per cm at a rate of 1.5 X 10-3 cm per sec. "As grown" crystals were aged for periods of 1 month at room temperature, then cleaved in liquid nitrogen, and etched according to the procedure used by Gilman.' The etchant containing 32 g of CrO3, 6 g of hydrated Na2SO3 in 100 ml of water behaved as a chemical polish for zinc and etch pits were produced at the site of precipitates or inclusions. After the precipitates or inclusions were removed from the surface, the etch pits left behind were eventually polished smooth. This behavior enabled one to continuously observe the surface while the specimen was immersed in the etchant. Best results were obtained when the specimen surface was vertical and the reaction products of polishing were continuously removed by gravitational convection. Some crystals were heavily deformed in excess of 25 pct strain, others were lightly deformed the order of a few pct by compression such that the deformation occurred essentially by basal glide. Some crystals were etched immediately after deformation, others were allowed to age at room temperature for several weeks prior to etching. Heavily deformed crystals were annealed at various temperatures and etched on the cleavage plane immediately after annealing, others were allowed to age at room temperature for several weeks prior to etching. The etched structures of deformed and annealed structures were studied. Similar experiments were conducted on 99.9999 pct pure zone refined Tadanac zinc crystals which

Jan 1, 1963