Search Documents

By G. C. Eggleston, W. E. Keck, W. C. Lowry

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,' and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6'7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.' EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.' Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

By W. O. Borcherdt

THE 650-ton underground mill of The Empire Zinc Company of Colorado (a subsidiary of The New Jersey Zinc Co.) serves the Eagle mine at Gilman in the Battle Mountain mining district of Colorado. The topography is rough, the mine and mill being under Battle Mountain and the alit entrance in the north wall of the canyon of the Eagle River, which is here a steel) gorge. The town of Gilman stands on a shoulder of the mountain at altitude 8975 ft., above sea level, along the Pike's Peak ocean to ocean highway and contains the company office and the usual facilities of a modern mining town. The railway contact is at Belden, altitude 8370 ft., at the bottom of the gorge directly below Gilman, where the westbound track of the Denver and Rio Grande Western Railroad is cut along the north bank and the eastbound track along the south bank of the river. A general description of the mine, mill and service facilities, with an account of the geology, character of the ore and methods of mining and milling having previously been published in a series of articles1, this paper will discuss with as little repetition as practicable the reasons for building the mill underground rather than as a conventional structure, the methods of construction employed and the experiences gained in what is apparently the pioneer plant of this type and extent.

Jan 1, 1937

By R. J. Charles

Previous study of simple impact systems indicated that energy required for fracture and size reduction of brittle materials is greatly dependent on the type of loading that is employed. In this regard it was postulated that fracture and size reduction of a brittle specimen might be accomplished by a high velocity impact at an energy level at which a low velocity impact would leave the specimen relatively undamaged. The finite time required to propagate energy away from the point of loading of an impacted object to other parts of the object and to its supports may permit a concentration of energy at the point of impact if the rate of loading is high. Localizing of energy at the point of impact could quickly initiate fractures that would propagate through the impacted material along with the traveling stress waves. As the cracks form, the initially absorbed strain energy would be released and portions of it travel ahead of the crack tips as stress waves. These secondary stress waves, combined with the initial stress waves derived from the impact, would produce high localized strain conditions in front of the fracture zone. The fracture zone would propagate and the specimen shatter. High rates of loading are brought about by short impact times, in turn obtained by employing high velocity projectiles that are of small mass compared to the impacted object.

Oct 1, 1956

By Allen J. Johnson

With a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Laboratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. Stokees Investigated One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.—The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plunger1 or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1936

By Allen J. Johnson

With a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Laboratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. Stokees Investigated One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.—The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plunger1 or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1936

By G. P. Connell, R. E. Gilmore, J. H. H. Nicolls

The purpose of this paper is to suggest a procedure for indicating the dividing line between noncaking coals and those that have weakly caking properties. A laboratory agglomerating test as an aid in classifying weakly caking coals is outlined and its merits in comparison with the standard agglutinating method advanced by the U. S. Bureau of Mines are discussed. No attempt, however, is made to discuss in detail either the different methods for determining "caking" and "agglutinating" indices or the various systems of classification. Two methods, differing somewhat in procedure, have been employed and recognized as suitable for determining the caking or agglutinating values of coals; namely, those in which an inert material such as sand, electrode carbon, etc., has been mixed with the coal before being heated, and those in which the coal is carbonized alone. In all such methods, the coal with or without the inert material is in the finely divided state and the index or value sought is derived from the examination of the residue after heating in a closed crucible or other container. The procedure outlined by Selvig, Beattie and Clellandl is the most recent representative of the method using sand as inert material, while the agglomerating test described below is representative of the method in which the coal is carbonized alone. The standard volatile-matter determination affords a means for observing the coking properties of a coal, and this has been described by Rose2 as the simplest of all coking tests. According to him, "the resulting coke button will indicate whether the coal is noncoking, feebly coking or strongly coking," despite the fact that "almost every condition in this test is at variance with large-scale carbonizing practice." Lessing,3 the

Jan 1, 1934

By Etienne A. Ritter

The Evergreen mine, located at Apex, in the northern part of Gilpin county, Colorado, has opened a very peculiar and interesting copper-deposit, in which both bornite and chalcopyrite occur as rock-minerals. The country-rocks are crystalline schists cut by dikes of granu-lite and of pegmatite. At the Evergreen property they have been cut by a dike of a uew kind of eruptive rock, to which I have given the name " Evergreenite." The rock is composed of quartz, alkali feldspars, orthoclase and albite (often interlocked as microperthite), with augite of the ægirine variety and long needles of enstatite and diallage. For reasons stated below, I believe the dike to be of Tertiary age. It is easily traced on the surface of the ground, from a point in the bottom of Pine creek, about a mile below Apex, to the top of Nevada hill, 1,500 ft. beyond and 600 ft. above it. (See Fig. 1.) It varies from 3 to 12 ft. in width, and is bounded on both sides by contact-zones about 60 ft. wide, in which the crystalline schists have been changed into pseudo-quartzites or pseudo-gneisees, according to the injection of an excess of quartz or of feldspars through the special layer of the schists. The most interesting feature is the presence of the pyroxenes, which are always found, though in very variable proportions from place to place, in the layers of these metamorphosed crystalline schists. The dike has torn from its walls a large number of fragments of the wall-rock. It must have been in a viscous state when that happened, because these fragments of the wall-rock do not show any sign of resorption or of assimilation by the magma. In places they are so distinct and so numerous that the rock looks to the naked eye like a pseudo-breccia, of which, never-

Jan 1, 1908

By F. C. Langenberg

IT is the purpose of this paper to present a limited amount of experimental data obtained on the Charpy impact machine. Several concrete examples will be given showing the relation existing between the results obtained upon the Charpy impact machine and the behavior of the parts tested when in service. Although it is pointed out by G. Charpy and A. Cornu-Thenard1 that it is first necessary to determine a satisfactory working process before studying the correlation between the results of these tests and the behavior of the parts tested in service, this ideal course cannot be strictly adhered to. If a certain part repeatedly fails in service and the available tests give no indication of its cause, advantage must be taken of any possible means that will solve the problem; therefore, even though the reliability of the results obtained by the Charpy impact machine have been questioned by many, it was necessary to use this instrument without giving careful consideration to its possible sources of error. It would seem that the conclusions arrived at by Charpy and Cornu-Thénard justify the assumption that the precision obtained by this machine is comparable to that obtained by, the other more common forms of testing. The second general conclusion arrived at by them, namely, that the impact test upon notching does not offer any direct correlation to the ordinary tests, is also borne out by many hundred determinations made in the laboratories at Watertown Arsenal. This statement, however, should be qualified as follows: Other ordinary tests include the static tensile test from bars taken in a longitudinal .direction and the Brinell hardness. The author agrees that no law is yet known for the computation of the energy absorbed in the rupture of bars of the same material but of different dimensions. Although Charpy and Cornu-Thénard do not refer in their valuable article to the use of the Charpy machine in industrial practice, it should be stated that this instrument has been in constant use in the laboratory at Watertown Arsenal for several

Jan 8, 1919

By Richard P. Rothwell

Fires in mines are so serious in their consequences and of such frequent occurrence, that their causes and the means of extinguishing them are certainly questions of the greatest interest to a large part of the engineering profession. We have already, in this country, many mines which have been burning for years, and though our hard anthracite is so difficult to ignite that for a quarter of a century after it was first discovered it mas not known how to burn it except with the aid of an artificial blast, yet most of the fires which have occurred underground have been in anthracite mines, and in the coal itself. The injury which these fires have caused to properties in various parts of the anthracite regions, and the cost of extinguishing them, would amount to many millions of dollars, and they have also occasioned the loss of many valuable lives. It is not surprising, therefore, that the subject has already attracted much attention, and the exercise of great ingenuity; and the present communication is made less with the expectation of announcing anything new, than with the object of putting upon record the present state of our knowledge on this subject, or, in other words, of indicating how defective are the present means of combating underground conflagrations. Causes of Mine Fires.—Even upon the surface, fire is a terrible foe to contend with, and there is probably no other which inspires such thorough and well-founded alarm. With what feelings, then, must we look upon this destructive element, when its field is in the narrow galleries of a mine, where the poisonous products of combustion, spreading in every direction, protect, in the most effectual manner, the fire itself from the attacks of extinguishers, while, if the face of attack be ventilated so as to enable then] to approach the seat of the fire, the air current simply increases the extent and violence of the conflagration. Fires underground originate in as various ways as those on the surface, and it is scarcely necessary to say that, except in the rare cases where they are the result of design, they are invariably classed as " accidents," and most generally as " unavoidable accidents." In reality, by an intelligent understanding of their causes and with due precautions, they can almost always be prevented. Ignorance and

By Chas Dobbel

THE Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. 1 mine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present.. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great. margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the wear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was usd to drive prospect holes with jointed steel.

Jan 9, 1925

By J. E. Johnson

The general construction of blast-furnaces has undergone no radical change in more than a generation. When the old style of masonry construction was replaced by the steel shell, the masonry piers were simultaneously replaced by columns, never lese than 6 and frequently 12 or 16 in number, set under the mantle-ring. These columns were at first unvaryingly made of cast-iron, but in more recent years have frequently been made of structural steel. The furnace itself has recently been the subject of radical changes; in some cases the thin-lined construction has been adopted for the whole furnace, and in other cases it has been adopted for a zone immediately above the bosh, raising the mantle several feet to make this possible, but still the style of construction with columns set immediately under the mantle has been universally followed. In spite of the apparent fixity of this type of construction it is open to grave disadvantages from the operating point of view, which may be briefly outlined as follows: The slope of the bosh and size of the crucible are such as to leave scant room inside the columns for the necessary water-piping, etc. The bustle-pipe must necessarily be outside the columns and the penstocks have to pass between them, with the result that the columns are frequently much in the way when changing the tuyeres or otherwise handling the penstocks. Moreover, the hearth-jacket requires a diameter but little smaller than the circle of the inside of the columns, and as a result the cooling-water ditch for protection against breakouts is exceedingly limited in width. As a consequence of these conditions, when any work requires to be done around the furnace, such as changing a tuyere or working on the cooling-water pipes, the amount of room left between the columns, pen-

Jan 1, 1913

By Alden B. Greninger

Many recent contributions in the field of theoretical metallography have been concerned with crystallographic definitions or descriptions of various phenomena. The lattice orientation of the crystal being studied must be known before such definitions can be made. Practically all the metallic crystals used do not have crystal faces—other than the unknown "plane of polish"; hence resort must be had to other means of determining orientations. Some use has been made of etch-figures, slip bands, optical properties, etc., for this purpose; but for accurate results, and because of the fewer restrictions to their use, the various X-ray methods have been the most satisfactory.' The methods that have been used may be divided into two general classes: (1) oscillation methods, and (2) transmission Laue methods.² The disadvantages of these methods are numerous, chief among them being the time required to determine a complete orientation. No method proposed so far is wholly satisfactory for determining the orientation of a small macrograin within a polycrystalline aggregate.

Jan 1, 1935

By Alden B. Greninger

Many recent contributions in the field of theoretical metallography have been concerned with crystallographic definitions or descriptions of various phenomena. The lattice orientation of the crystal being studied must be known before such definitions can be made. Practically all the metallic crystals used do not have crystal faces—other than the unknown "plane of polish"; hence resort must be had to other means of determining orientations. Some use has been made of etch-figures, slip bands, optical properties, etc., for this purpose; but for accurate results, and because of the fewer restrictions to their use, the various X-ray methods have been the most satisfactory.' The methods that have been used may be divided into two general classes: (1) oscillation methods, and (2) transmission Laue methods.² The disadvantages of these methods are numerous, chief among them being the time required to determine a complete orientation. No method proposed so far is wholly satisfactory for determining the orientation of a small macrograin within a polycrystalline aggregate.

Jan 1, 1935

By J. Steininger

The Hallimond tube flotation of sphalerite and pyrite with sulfhydryl collectors has been found to be inhibited near neutral pH in the presence of copper salts. Alkalimetric titration studies of the reactions between collector and activator indicate that this effect is apparently related to the formation of basic copper collector complexes. The conditions of formation of these compounds and their stability are in good agreement with the depression observed in flotation experiments. The general procedure employed in the flotation of zinc sulfide minerals requires activation of the mineral surface by heavy metal ions, usually copper, which react more easily than zinc with the common short-chain ionic sulfhydryl collectors.' Commercially, zinc flotation is carried out under alkaline conditions (pH 7 to 10.5), but small-scale experiments indicate that zinc sulfide minerals can also be activated and collected under acid conditions. Selectivity, however, becomes poor at low pH and undesirable materials such as pyrite, silicates and carbonates tend to report in the float. Several years ago, Wark and Sutherland~, measured the contact angles of air bubbles on copper-activated sphalerite immersed in various sulfhydryl collector solutions. When represented, as in Fig. 1, on pH-sodium cyanide diagrams, the results are characterized by 'islands' of non-contact near neutral pH and

Jan 1, 1969

By K. Huessener

In presenting the following data on combustion in the open hearth furnace and the advisability of automatic combusion control, the author finds himself much more severely handicapped by the lack of reliable test results than he had anticipated when he first undertook to write this paper. In order thoroughly to investigate how the results of an open-hearth furnace are influenced by combustion, one would have to draw up a large number of heat-balance sheets, as Kinney and McDermottl have given for one heat in their extremely able paper on "Open Hearth Efficiency,' presented before the American Iron and Steel Institute on October 27th,1 1922. Instead of covering only one heat, however, such heat-balance sheets would have to embrace a large number of heats, and not only for one kind of fuel, but for all the various fuels in customary use. Use of Radiation-protected Pyrometer Such tests necessitate extremely careful temperature readings, and here the first serious difficulty presents itself. Nearly all the temperature readings so far published have been taken with thermocouples for the lower ranges and with optical or radiation pyrometers for the higher ranges. This method of measuring reveals the temperature of the surrounding walls, or in the case of optical or radiation measurements, the temperature of that part of the opposing walls which has been focused by the instrument. The error in ascertaining the temperature of the gases entering or the waste gases leaving the checker chambers is probably not very large, as the flowing gases impart their temperature to the walls of the flues. On the other hand, the uptakes, where the preheat temperature of gas and air are usually measured, are under the influence of radiated heat from the port ends, and correct temperature readings can here be taken only by using a radiation-protected pyrometer of the aspirating type.

Jan 1, 1926

By Reuel A. Cochrane, Harry H. Angst

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Harry H. Angst, Reuel A. Cochrane

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By L. G. Jones, A. S. Odeh

A theoretical developtment is presented which provides a straightforward method of handling the drawdown analysis for both oil and gas wells flowing at variable rates. In the past our inability to analyze variable-rate drawdowns has been a major obstacle in using them for formation evaluation. This method should permit wider use of these tests in the future. INTRODUCTION Pressure build-up analyses are widely used to obtain reservoir data such as the effective flow capacity of the formation. On the other hand. although pressure drawdowns have been run for a long time, they have not been used extensively to evaluate reservoirs because they are difficult to analyze. One of the difficulties in analyzing pressure drawdowns has been that the theory developed until now has required the test to be run at a constant rate. For both oil and gas wells this is a difficult requirement to satisfy. especially during the early period of a well's life when drawdown tests are usually run. In spite of this limitation, drawdown tests are often run with build-ups as a check. In this paper a theory, which handles the drawdown analysis for variable rates, is presented for both oil and gas wells. Thus, one of the biggest deterrents to running drawdowns is removed, and they should become a much more useful engineering tool in the future. THEORETICAL CONSIDERATIONS 011, RESERVOIRS The general equation used for describing the unsteady-state radial flow of slightly compressible fluids in homogeneous porous media can be written in cylindrical coordinates as where r is the radial distance in cm, t is the time in seconds, p is the pressure at r and t in atmospheres, + is the fractional porosity, p is the viscosity in cp, c is the compressibility in vol/vol/atm, and k is the permeability in darcies. There are a number of solutions of Eq. 1 for various boundary conditions. One of these is the so-called "point-source" solution, which approximates the case of an infinite oil reservoir with a well located at r = 0 and produced at a constant rate. The point-source solution of Eq. 1 is

Jan 1, 1966

By W. Rostoker, A. Siede

THE venerable problem of hydrogen embrittlement of ferritic iron lacks as yet a complete explanation. Possibly part of the difficulty has been the exclusive preoccupation with the total ductility prior to fracture. In the past few years it has been noted at least twice1,2 that hydrogen charged into iron has the ability to depress the upper yield point and, at room temperature, to eliminate completely the discontinuous yield phenomenon. Cracknell and Petchl rationalize that the depression of the yield stress is an example of the behavior of inhomogeneous stresses. Their explanation requires that microcracks exist in the annealed metal, and that hydrogen collect in these cavities under high hydrostatic pressure. The hydrostatic pressure of hydrogen generates localized tensile stresses in the iron which, with external loading, reach the critical stress for yield prematurely. The local plastic zones will spread across the specimen before the Lüders bands can be generated, and the yield-point elongation phenomenon is eliminated. This viewpoint will be discussed in succeeding paragraphs. Rogers,2 on the other hand, represents the depression of the initial flow stress as a result of the interaction of hydrogen with dislocations. He submits two alternative modes of interaction. In the

Jan 1, 1959