Search Documents

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi [ ] fled by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity -the hot hammer test. Samples Y2 in. in diameter and ¾ in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher tempera¬tures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of' reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Albert Sauveur

SOME writers believe that when austenite transforms completely into pearlite on slow cooling through the thermal critical range, such transformation does not imply the formation of any of the so-called transition constituents: martensite, troostite and sorbite. Might it not be claimed with as much justification that when water freezes it does so suddenly, solid ice being obtained without passing through the intermediate stages of ice and water? Obviously, regardless of the speed of solidification, this would be erroneous. Before reaching the completed solid condition, this must of necessity pass through an unbroken series of stages when the system consists of mixtures of water and of ice, the former decreasing and the latter increasing in amount. Are not these "transition" stages in the freezing of water similar to the transition stages occurring in the transformation of austenite into pearlite? To clarify, let us consider in Fig. 1 the mechanism of the transformation of eutectoid steel from its austenitic to its pearlitic condition as it cools slowly through its thermal critical range. It is generally admitted that this transformation is the result of two distinct phenomena: (1) the allotropic change of gamma iron into alpha iron and (2) the crystallizing out of solution of the carbide Fe3C. Whether this crystallizing of Fe3C implies also its formation is immaterial for our purpose. In other words, whether it is the carbon in atomic dispersion which is present in gamma iron or molecules of Fe3C has no bearing upon the matter to be discussed. The transformation of gamma iron into alpha iron cannot take place suddenly. It must of necessity be progressive, regardless of the speed with which it may take place. At A, for instance, there would be present AB gamma iron and BC alpha iron. The distance MN does not refer to falling temperature, but to the passage of time. It may be assumed that the transformation takes place at a constant temperature (the Ar321 point). In a similar way, the crystallization of Fe3C out of the austenite solid solution must be progressive as depicted between M and N. At A there would be present AB gamma iron, BC alpha iron, CD carbon dissolved in gamma and in alpha iron and DE Fe3C. This condition may be described according to individual preference as martensite or troostite. To sum up, can the metal pass from condition

Jan 1, 1931

By Martial P. Corriveau

Almost everyone agrees that coal and oil shale are the only fossil fuel resources in which the United States is self-sufficient. Of the two, only coal has a technology sufficiently developed to be of intermediate term benefit. Since it takes at least 20 years to bring advanced technology into practice, it seems logical that the major focus on energy developments should be aimed at coal. Meanwhile, we need to trade-off between actions to meet our immediate needs and the various political regulations and social demands that are disrupting the coal industry and the industries dependent upon it. The largest single user of coal is the electric power generation industry. Over 300 million tons of coal are presently being consumed each year. In view of the 5-to 7-years lead time to bring in a base-load fossil-fuel fired generating station, our requirements for double this tonnage in 1980 are already well forecast; that is, if the coal companies are allowed to mine and the utilities are allowed to burn the coal.

Jan 2, 1974

By T. A. Rickard

RICO, in the southwestern corner of Colorado, is one of the productive mining centers of the San Juan region, so-called because its waters drain into the river of that name, which is tributary to the Colorado. The San Juan region includes the counties of Ouray, Hinsdale, San Miguel, Dolores, San Juan and Montezuma. It is traversed by a network of picturesque mountain ranges on whose lofty summits there rests perpetual snow. The region is peculiarly rugged, and, in the early days of its development, tested to the full the hardihood of the adventurers who first explored its can ions 111 search for gold and silver. A prospecting party, guided by Jim Baker, scout and trapper, penetrated in 1861 this part of the territory of Kansas. At that time the country was in the possession of the Ute Indians. In October, 1873, by the Brunot treaty, they ceded to the United States Government the richest mineral-bearing portion of their

Jan 1, 1897

By P. B. Knuckey, D. Littleford

The Kalengwa mine, situated in a remote area of Zambia in Central Africa, has presented some unique problems to the planners engaged in developing the deposit. This small, high grade copper deposit contains some 1,688,000 tons of ore at a grade of 9.3% contained copper. Of this 362,000 tons is classified as high grade ore at 27.2% Cu, the coarse fraction of which can be fed directly to converters; 733,000 is classed as intermediate grade ore averaging 6.3% Cu, and 593,000 tons classed as low grade ore containing 2.1% Cu. The geology of the deposit and the establishment of the mining operation is fully described. A concentrator is being built at Kalengwa to treat the high grade fine product, intermediate, and low grade ore, whilst the coarse high grade ore will be trucked to the Copperbelt smelters for direct smelting. Details of metallurgical processing are given. The decision to truck the coarse high grade ore to the smelters on the Copperbelt necessitated the construction of a new 200-mile road, the setting up of a fleet of heavy ore transport trucks and associated equipment. The remoteness of the area from established communication facilities on the Copperbelt necessitated the provision of radio communications between Kalengwa and the head office at Kalulushi, and the establishment of a regular mine air service. The paper also describes the training of an unsophisticated local population in the operation of heavy plant and machinery, the establishment of the township, and the provision of health services.

Jan 1, 1972

By D. B. Rushmore, K. A. Pauly

Of primary importance in mine-installations is the hoist, which has a very direct bearing on the successful operation of a mine. Conditions vary greatly with different mines, and especially in different localities. Such factors as depth, incline, the number of levels, permissible or desirable speeds, conditions of ore, etc., are always more or less special in each case. Veins of ore are never exactly duplicated, and the nature of the ground through which shafts are sunk may considerably modify permissible values. As mining-laws are made by the different States, they necessarily vary somewhat, and, even when not fully observed, they introduce factors which qualify the conditions of hoisting men and ore. The amount of timbering required is often of importance as relating to hoisting-conditions. Methods of loading ore affect the time required, as also does the question of the use of cars or skips. Safety-precautions must be very carefully considered, and the number of men in each mine, the number of compartments, and often the method of removing water from the mine, must have careful consideration. While a general discussion of the subject of hoisting is possible, most cases are entirely special, and can be considered only in connection with the peculiar conditions pertaining to that particular installation. The cost of installation of the hoisting-plant may be an appreciable amount, while the cost of raising the ore may be but a small part of the total operating-charge. In many cases, however, the output of the mine is limited by the capacity or the hoist, and the latter thus becomes of the first importance.

Jan 1, 1911

By T. D. McKinley

Theory, operational characteristics, and indicated precision and accuracy of analytical methods based on vacuum extraction, equilibrium pressure, and combustion approaches are reviewed. At the present time vacuum extraction at 1400°C and the equilibrium pressure method are recommended for determination of hydrogen in titanium and titanium-rich alloys. UNTIL a few years ago the role of hydrogen in titanium was an unknown factor with regard to its effect on the physical and mechanical properties of the metal. However, following the work of Jaffee and othersa-" it is now generally acknowledged that hydrogen has a degrading effect on titanium and its alloys. The chief manifestations are a decrease in impact strength in -systems and delayed cracking in a-ß systems. Since hydrogen does have a de- grading effect on titanium it is essential to control it within tolerable limits. It then follows that procedures for quantitative estimation of hydrogen are a primary requirement for the industry. For greatest benefit these methods should be simple, rapid, and precise. In addition to having these virtues, methods must be easy to duplicate in both equipment and technique to gain widespread use. After inherent accuracy has been established, the, required precision to make a method acceptable is dependent largely on the nature of the work at hand. Ability to obtain a representative sample has a pro-

Jan 1, 1959

By R. F. Domagala, M. Hansen, D. J. McPherson

Iodide zirconium was combined with calculated amounts of nitrided zirconium sponge and arc melted to prepare alloys in the 0 to 6 wt pct N region. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat-treated specimens permitted construction of the binary phase diagram from 0 to 6 pct N. Features of the diagram include the peritectic formation of both a and ß solid solutions. The maximum solubility of nitrogen is 0.8 pct in 8 zirconium and 4.8 pct in a zirconium. An X-ray study of nitrided materials was made in the range 6 to 13 wt pct N region because serious nitrogen losses were experienced when attempts were made to arc melt these high nitrogen alloys. PHASE relationships in the Zr-N system have been determined. Due to the inability to retain nitrogen in nitrogen-rich alloys subjected to arc melting, definitive work was possible only in the range 0 to 6 wt pct (0 to 30 atomic pct) N. Sufficient complementary X-ray work was done to permit construction of the binary phase diagram up to 13.3 wt pct (50 atomic pct) N (ZrN). Small ingots were prepared by arc melting master alloys with enough zirconium to produce an alloy of the desired composition. Following pretreatment, alloys were annealed at temperature levels between 600" and 2020°C. Determination of the phase boundaries was then accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to corroborate solidus curves, and X-ray diffraction was employed to study the nitrogen-rich region of the a + ZrN phase field. Materials Westinghouse Grade 1 iodide zirconium crystal bar served as the base material for this investigation. The as-received bars were lightly sandblasted, pickled in a 20 pct HN0-5 pct HF aqueous solution, rinsed in water and acetone, and dried. They were rolled to about 1/32 in. strip and acid-pickled, followed by water and then acetone rinses. The material was sheared to approximately 1/4 in. squares, cleaned with acetone, and stored for use. Pure zirconium nitride is not commercially available, according to correspondence with possible suppliers. A literature survey indicated that nitrogen may be introduced into zirconium metal by passing nitrogen or ammonia gas over zirconium at an elevated temperature. After considerable experimentation, a train was devised whereby high quality nitrogen was passed through a series of bubblers to remove the last traces of oxygen, through an H,SO, bubbler and a cold trap to remove moisture, and finally over zirconium within a resistance furnace. Hand-picked Bureau of Mines magnesium-reduced zirconium sponge proved more amenable to nitriding than the crystal bar. The nitrogen used was extra pure gas purchased from Linde Air Products Co. The first two bubblers through which the gas was passed contained a solution suggested by L. F. Fieser" as being ideal for removing the last traces of oxygen from nitrogen. The solution contains 20 g KOH, 2 g sodium-anthraquinone ,9-sulphonate, and 15 g NaHSO, dissolved in 100 ml water. It is blood-red and turns brown when contaminated with oxygen. A saturated lead acetate solution, next in the series of bubblers, removed any H2S which might have formed in the 0, removal stage. An H,SO, bubbler and cold trap removed moisture before the nitrogen was passed over the zirconium. The zirconium was contained in a stainless steel screen within a Vycor or quartz tube in a resistance furnace. Unreacted nitrogen passed out of the system through a mercury bubbler. A nitriding run was performed in the following manner: Zirconium was placed in the screen within the furnace tube. The unit was assembled, suitably clamped off, and evacuated to remove the air and moisture within the tube and that trapped by the zirconium sponge. The unit was flushed with nitrogen and evacuated twice. After nitrogen was allowed to pass over the zirconium for about 30 min, the furnace was turned on; several hours were required to reach temperature. The reaction was allowed to continue at temperature for about 4 hr and the screen was then withdrawn from the hot zone of the furnace by means of a Nichrome or Kanthal rod. The screen and its contents were allowed to cool at the end of the tube and were then removed. At 800°C no more than about 5 pct N could be introduced into the sponge zirconium. This material was designated M-1 (master alloy No. 1) and reserved for the preparation of alloys in the dilute nitrogen region. A second set of experiments was conducted at 1000°C; no more than 7.2 pct N could be introduced into the zirconium at this temperature. Enough material (M-2) of this nitrogen content was prepared to produce a second set of alloys to complement the first and to provide alloys in the 0 to 6 wt pct N range. It was hoped that a diffusion anneal plus a re-nitriding might yield a material of higher nitrogen content. The material containing about 7 pct N was therefore given a homogenization treatment at 1000°C for 6 hr under an argon atmosphere. It was

Jan 1, 1957

By Harry A. Lipsitt, Douglas Y. Wang

A fatigue study in completely reversed axial tension-compression has been perforried on high-purity titanium and on three high-purity alloys of titanium. The alloys each contain approxi7nately 0.75 at. pct of a single interstitial element; carbon, nitrogen, and oxygen, respectivley. The results corroborate a previously published theory which proposed that strain aging under alternating stress was responsible for the fatigue limit behavior of certain alloys. The present data indicate that in these alloys an increasing strain-talline aging effect under alternating stress is provided by oxygen, carbon, and nitrogen, respectively. CURRENT research on the nature of the fatigue limit in metals suggests that the presence of a fatigue limit in metallic materials is a manifestation of strain aging that occurs under alternating stress.lm5 A comprehensive theoretical model based on the above hypothesis has been developed to explain the existence of a fatigue limit.' This model also provides increased insight into several other fatigue phenomena as under stressing, overstressing, and coaxing effects. The theory, as well, provides equal understanding for those cases where no real fatigue limit is observed. Briefly, this theory assumes that the S-N curve for a pure metal is a smooth function of the applied stress, and the effect of adding an element that is soluble (or forms a precipitate) in the pure metal is simply to shift the S-N curve to the right. If the added element confers the power to strain age, the result is a further shift of the S-N curve, this time upward and to the right. Since strain aging is not expected to be a strong function of stress, and since damage per cycle is known to be quite stress dependent, it is to be expected that there will be some limiting lower stress at which the strengthening due to strain aging will balance the damage due to crack propagation. This stress is the fatigue limit. The position of the fatigue-limit knee was thought to be a function of the magnitude of the strain-aging effect on both the finite and infinite life portions of the S-N curve. Although the strain aging hypothesis seems to be reasonably valid for bcc materials,2'6 it needed to be tested for both fcc and cph metals. This report is the first of a series concerning the fatigue-limit behavior of titanium with varying amounts of the interstitial solutes (C, N,, and 4) that are known to cause static strain aging in titanium. Yield-point effects have been reported for polycrys-talline high-purity titanium alloys containing either carbon, nitrogen, or oxygen.7'9 These effects were observed at testing temperatures in the range 100 to 300'. In addition yield-point and strain-aging effects have been reported for single crystals of titanium containing 0.1 wt pct C plus N.' These yield points were observed over a wide temperature range, but no room-temperature aging occurred. Aging at 180' was required to cause the return of the yield point. The magnitude of the yield phenomena in titanium containing interstitials is not expected to be as large as is observed in bcc metals because of several factors. Titanium has a very high chemical affinity for oxygen and nitrogen. The thermodynamic stability of solutions of oxygen or nitrogen in titanium is recognized. Lattice parameter measurements of titanium containing arbon, oxygen,1° or nitrogen" show that the "c" parameter is expanded more than the "a" parameter, but that up to about 2 wt pct this results in an insignificant change of the axial ratio 'c/a." Ehrlich" has shown that the sites occupied by interstitial atoms in titanium are spherically symmetrical and therefore a lattice expansion, at a constant c/a ratio, results in a simple dilation of the interstitial site. Such a dilation involving no shear has been shown to react only with edge components of dislocations.13 This causes only a weak pinning action. Shear stresses would be anticipated locally when only one of the two interstitial positions was occupied. The carbon atom will cause a symmetrical distortion of the lattice whereas the oxygen and nitrogen atoms have, in addition, the previously mentioned chemical affinity of titanium for these elements. These factors will result in a considerably smaller reduction of free energy upon the association of interstitial atoms with dislocations, and therefore a much weaker pinning than has been observed for the bcc metals. These considerations would lead to the hypothesis that of the interstitial elements considered here carbon would cause the strongest pinning effect in titanium where the amount of interstitial in solution is constant. This hypothesis will be borne out in the analysis of the present results.

Jan 1, 1962

By M. J. Marcinkowski, A. Szirmae, R. M. Fisher

Room -temperature hardness measurements obtained from single and polycrystalline samples of a 47.8 at, pet Cr-Fe alloy which were aged for various times al 500°C show a two-fold increase over that of the unaged alloy after annealing for 1000 hr. A detailed examination of the deformation markings in the neighborhood of the hardness imbressions reveals that twinning becomes an increasingly more important mode of deformation as aging proceeds. this observation is shown to be inconsistent with the Proposals that the transformation is eve of order-disorder On the other hand, the results are in agreement with previous observations of Fisher et al. of a coherent chromium-rich precipitate which forms in an iron-rich matrix as a result of a miscibility gap in this alloy system as proposed by Williams . Using the coherent precipitate hypotlzesis as a model, a detailed analysis of the various possible strengthening contributions to both the slip mid twinning stresses is made. In the case of' slip, lattice friction within the chromium-rich phase and the chemical energy associated with the interface between the two phases contribute about 60pet to the total strength. The contributions from coherency strains and modulus differences are thought to contribute the remaining 40 pet of the strength but are difficult to evaluate because of uncertainties regarding the flexibility of the dislocation line. All of the factors have nearly the same or else a smaller effect on the twinning stress in the aged alloy. Twinning is never observed in the unaged alloy because the twinning stress is much higher- than that for slip. With increased aging times, the various contributions to the total stress for both twinning and slip increase, but most of those for slip increase much more rapidly, so that, in the fully aged alloy, it surpasses the stress for twin propagation. When a twin is nucleated by the chance occurrence of an internal stress concentration during a test, the subsequent twin burst results in a low hardness reading. FeRNTIC Fe-Cr alloys from about 15 to 80 at. pet Cr content show considerable change in properties such as hardness, electrical resistivity, saturation magnetization, and so forth, after aging in the vicinity of 500°C.* The most marked change is a large increase in hardness accompanied by a sharp decrease in ductility, so the phenomenon has often been referred to as the 475°C (885°F) em-brittlement problem. Changes in microstructure are rather subtle and most investigators have not been able to observe any X-ray diffraction or metal-lographic changes during aging. There is little doubt that the phenomenon is inherent to the Fe-Cr binary system and is not directly related to the formation of a phase. Two distinct schools of thought have developed during the past decade concerning this problem. Masumoto, Saito, and sugiharal have concluded, from their own specific-heat measurements, that atomic ordering occurs in this temperature range. Pomey and Bastien2 have also attributed the changes in physical properties with aging in the neighborhood of 500°C to atomic ordering. In addition, Takeda and Nagai3 claimed to have found X-ray verification for superlattices corresponding to the compositions FesCr, FeCr, and FeCr3. However, all known attempts to observe superlattices in Fe-Cr alloys using neutron diffraction, which should be much more sensitive, have been unsuccessful. These have been reported by Shull et al.4 for 25 at. pet Cr, williams5 for 75 at. pet Cr, and Tisinai and samans6 for a 28.5 at. pet Cr. steel. The second and more prevalent opinion ascribes the 475°C embrittlement phenomenon to the formation of a coherent precipitate due to the occurrence of a miscibility gap in the Fe-Cr system below about 550°C. This latter concept was first indicated by the results of Fisher, Dulis, and Carroll,7 who were able to extract fine particles about 200Å in diameter from samples of 28.5 at. pet Cr steels aged from 1 to 3 years at 475°C. The extracted material was found to be nonmagnetic, to have a bee structure with a lattice parameter between that of iron and chromium, and to contain about 80 at. pet Cr. Williams and paxton8 and williams5 confirmed these results and first explicitly proposed the existence of a miscibility gap below the a region in the equilibrium diagram. Alloys aged within this gap

Jan 1, 1964

By Paul A. Filteau

Asbestos ranks among the leading minerals produced in Canada. It is also mined in Russia, Rhodesia, South Africa, Cyprus, Italy, the U.S.A., Japan, China and several other countries. The most abundant variety, chrysotile, and also the most valuable form of asbestos produced, makes up 90% of the world's supply. In Canada, chrysotile is found in the provinces of British Columbia, Ontario, Newfoundland as well as in Quebec, the latter accounting for almost 90% of all the fibre produced in this country. A number of developments emerging this year could make 1968 a record production and export year for Canada's asbestos mining industry. Asbestos fibre consumption in increasing in the U.S., Canada, up 10% to date this year, Japan and in Latin America. Demand in Western Europe is again on the upswing, following a cut-back last year. As a result, shipments from Canadian mines for the first eight months of this year reached some 916,968 tons versus 873,402 in 1967, an increase of 43,566 tons or 5%. Indications are that Canadian asbestos production will for the first time ever top 1.5 million tons in 1968.

Jan 1, 1969

By Kurt Stock

The war caused a demand for enormous quantities of high-grade zinc, which were not available and could not be produced from pure ores in sufficient amounts and in the time required. Redistillation of virgin spelter on a large scale was practiced to supply this demand; this paper gives a full description of the process used by the Oklahoma smelters of the Bartlesville Zinc Co. As the redistillation of zinc has become of historical interest only, having been superseded by the electrolytic process, it was deemed advisable to give expression to this phase of the metallurgy of zinc that, in the past, had never gone beyond laboratory experimentation. THE grades of spelter demanded by the consuming industries were not definitely established until the American Society for Testing Materials undertook to fix specifications, based on the varying percentages of the common impurities (lead, iron, and cadmium) as follows: TOTAL, NOT LEAD, IRON, CADMIUM, OVER. PER PER CENT. PER CENT. PER CENT. CENT. A. High grade 0.07 0.03 0.05 0.10 B. Intermediate 0.20 0.03 0.50 0.50 C. Brass special 0.75 0.04 0.75 1.20 D. Prime western 1.50 0.08 The question which grade was the best for certain purposes and why was left unanswered. The conservatism of the zinc-smelting industry and the unwillingness of the spelter-consuming industries to engage in research work prevented the full benefits being obtained that such standardization promised. The custom smelters, producing spelter in pigs or plates, found it impossible to adhere closely to the established limits on account of the variety of ores treated; and the smelters with long-established and known brands, or those manufacturing their metal into marketable products, like sheet zinc, did not have to abide by the newly established grades based on chemical percentages.

Jan 7, 1924

By Philip B. Bucky

[ ] FOREWORD THIS symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge,

Jan 1, 1942

By C. E. Shoenfelt

Jan 1, 1942

By C. E. Shoenfelt

Jan 1, 1942

Jan 1, 1951

By Edwin B. Wilson, Joseph W. Leonard, Richard W. Borio

preparation of specification coals for the utility industry is approached from the standpoint of a cooperative effort with the power company to assure that the shipped product will be a noncorrosive coal. Selective mining, coal preparation, the use of additives, and coal blending are mine-site techniques proposed as means for upgrading corrosion-retarding constituents of utility coals (CaO and MgO) while, at the same time, reducing the concentration of those constituents of coal (Na20 and K,O) which cause corrosion. Data obtained from large-scale boiler testing in combination with bench-scale physical and chemical tests are used as a basis for the formulation of mine-site procedures to improve coal combustion utilization. Electric power generation remains the greatest market for coal in the United States. A major reason for this strong market has been the ability of the coal industry to supply a superior product for combustion while maintaining competitive prices. Now that the coal industry is engaged in intensive competition with nuclear power for future energy demand, it becomes ever more imperative that superior coal products are produced. One important problem when burning some coals is a liquid phase corrosive attack on boiler tube metal in the superheater and reheater areas of the furnace where steam temperatures may exceed 1050°F. In addition to causing power outages and high maintenance costs, corrosion is a continuing barrier to the future development of more efficient steam cycles which permit lower generation costs when using coal. Research methods of the past which have been directed at finding solutions which could be applied at the power plant site have been only partially successful and are generally costly. This paper contains a suggested --method of corrosion control through investigation of the problem at the source of the trouble—the coal supplier facility. It is proposed that mine-site pre-ventative procedures be considered as an effective means of cooperative corrosion control between the power company and the coal supplier. Economic justification must be applied to the individual situation. This paper is based on recent work by Combustion Engineering, Inc. and the Coal Research Bureau of West Virginia University under a contract from the Department of the Interior Office of Coal Research.',' Results which are of importance to this discussion may be summarized as follows: 1) The alkali minerals of coal (Na2O and K2O), as measured by an acid leaching process, can be related to corrosion rate in utility boilers. As these constituents increase in a coal product, its corrosiveness can be expected to worsen. 2) The alkaline-earth minerals contained in coal, reported as total CaO and MgO reduce corrosiveness 2s their concentration increases. 3) Naturally occuring, alkaline-earth-bearing materials, such as limestone and dolomite, may be added to a coal to reduce its corrosiveness. 4) Coals with very low iron contents tend to be less corrosive. These results provide the groundwork for examination of the system of operations which occur at the supplier facility from the seam face where mining is begun to the point of loading for shipment. The Mining System Fig. 1 is a cross section of one of the typical coal seams (designated coal A) that was boiler tested during this research program. This seam is overlain by material which consists primarily of a gray-black shale. In the lower third of this seam, there exists a thin rock parting of less than 4 in. in thickness which is consistent throughout the seam. The floor material is fireclay. In order to examine mineral distribution throughout this particular seam, the Coal Research Bureau collected a

Jan 1, 1971

Jan 1, 1923

By R. D. Pehlke, J. V. Gluck

A study was made of the effect of small additions of metallic solutes on the thermodynamic activity of zinc in dilute solution with molten bismuth in the range 450o to 650°C. The experimental measurements were made in a multielectrode galvanic cell using. a fused LiCl-KCl electrolyte. The activity of zinc in binary solution exhibited a strong positive deviation from Raoult's law and obeyed Henry 's law to at least 0.050 mole fraction. The ternary addition of lead, gallium, or indium increased the activity of zinc. Cadmium or tin additions slightly decreased the zinc activity. Copper, mercury, silver, or antimony caused moderate decreases, while gold strongly decreased the zinc activity. The results are expressed in terms of Wagner's interaction parameter ejZn and a second-order cross-interaction parameter. The interactions for copper, gold, silver, and antimony showed a linear dependence with reciprocal absolute temperature, while the other interactions were essentially independent of temperature over the experimental range. Since tin and antimony decreased the zinc activity, the hypothesis of a purely periodic variation with atomic number was rejected. A semiquantitative explanation was possible with a free-electron model when relative electronegativities were used to express changes in the electron/atom ratio caused by the solute addition. Random solution and quasi-chemical models correctly predicted the majority of the interactions for which binary data were available to apply them. A knowledge of the thermodynamic interactions in liquid (and solid) metallic solutions is of considerable theoretical and experimental interest in the formulation of quantitative thermodynamic relations for metallurgical processes. The approaches to defining the interactions may be either phenomenological (i.e., "What mathematical function adequately describes observed behavior and permits extrapolation to new situations?") or theoretical, such as a specific model

Jan 1, 1968

By J. Ruzicka

IN creep testing, material is subjected to a constant load, preferably at a constant temperature, and its rate of deformation is measured. The method of loading can be of various types but in this paper only creep testing under tensile load will be considered. The ordinary tensile test is essentially a comparison test in conditions that frequently bear little or no relation to those under which the test material is to be used in service. The purpose of creep tests is to measure the strength of the test material at slow rates of deformation that more nearly approach the rates realized in service. One purpose of this paper is to illustrate that the creep test, in addi-tion to its value as a service test, is superior to the ordinary tensile test as a sensitive tool for the comparison of certain metals in investigative testing. The other purpose is to describe equipment having distinctive features of design that make it especially suitable for such tests. Representative data obtained with this equipment on a group of rolled zinc-base materials are given. These data are compared with those from practical comparison tests of the creep type on weatherstrip fabri-cated from the same group of materials. The comparison illustrates the value of the fast creep test and of the equipment.

Jan 1, 1937