Search Documents

By Richard H. Willey

EFFICIENT handling of large tonnages in open-pit mining demands, primarily, an abundance of well fragmented rock. To accomplish this, a drilling and blasting department composed of a well-knit, versatile group of workers and supervisors must be established. Some costs will remain relatively on the same level over a period of years, while others can be greatly lowered as will be shown. The Utah Copper Division, Kennecott Copper Corp., Bingham Canyon, Utah, has been ever alert for improvements in operating methods and equipment to gain increased efficiency and lower costs. BINGHAM CANYON MINE The greatest dimension of the mine is 8000 ft northeast-southwest with a width of 5000 ft southeast-northwest. From the lowest level, at an elevation of 6040 ft above sea-level, the mountain rises in 27 benches on the west side to W level (elevation 7800 ft) and 21 benches on the east side to Q level (elevation 7460 ft). At the inception of open-pit mining in 1906, the overcapping of leached porphyry had to be removed to reach a commercial grade of sulphide ore. The overcapping or waste now remaining is quartzite with intercalated limestone beds. The limestones are usually soft in nature except in the south-middle portion of the mine where they have been metamorphized along the contact zone. This area usually gives drilling and blasting operations a great deal of trouble. Here occurs the greatest amount of secondary blasting, as the well-established fracture planes cause the altered beds to break into large boulders. Several massive quartzite "ribs" occur in the overburden, and as a result, the uniform breakage is difficult to obtain. The major quartzite areas have been subjected to complex folding, fracturing and faulting because of the intrusion of the underlying stock. The monzonite porphyry, which carries the commercial values, presents no serious drilling problem because of its softness and extensive minute fracturing throughout the mass. A series of major slips or faults pass through the ore body which, although of considerable advantage to the drilling and blasting department, sometimes works to the disadvantage of the track department. Drilling and blasting of the porphyry apparently becomes easier as depth is attained, but highly siliceous streaks throughout the pit still present difficulties. At no place is the rock of such character as to allow excavation without preparations. On certain higher elevations or levels, old fill material can be dug by the shovels, but only at some risk to equipment because of bank slippage. PAST METHODS At the outset of shovel operations in 1906, drilling was done with the Ingersoll-Rand F-24 piston drill mounted on an un-

Jan 1, 1947

Discussion of the paper of W. R. Shimer and F. O. Kichline, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 81, September, 1913, pp. 2361 to 2377. ALLERTON S. CUSHMAN,* Washington, D. C.:-I have been much interested in Mr. Shimer's valuable contribution. The apparent fact that the oxides of certain metals which are not reduced by hydrogen per se, are reducible when the oxides are dissolved in iron in small quantity, is brought out for the first time, and is worthy of the careful attention of investigators. The Ledebur method has been subjected to considerable criticism, owing to the alleged fact that it did not measure the oxygen combined with impurities. Personally I have found the method extremely helpful in spite of the minute quantities of oxygen with which it deals. Mr. Shinier points out that the highest oxygen he obtained by over-blowing was 0.074 per cent., while the minimum quantity in a properly finished steel was in the neighborhood of 0.02 per cent. The Ledebur method is used as a constant check on the quality of heats made in practice under my direction. In dealing with a very pure commercial iron, we should expect to find and would find difficulty in galvanizing sheets made from a heat running 0.07 per cent. oxygen. In fact, we do not like to have the oxygen rise above 0.03 per cent. I am inclined to agree with the author that excessive oxygen leaves a bath of metal in a very short time, but nevertheless I believe it takes only a very little combined oxygen to begin to make its presence felt in the pickling and galvanizing department, when sheet metal is the product manufactured. As Mr. Shimer points out, the higher the carbon, the lower the oxygen danger, and it is partly for this reason that the manufacture of carbon-free metal in the open-hearth furnace has to be so very carefully watched and controlled from the furnace through to the finished product. It is quite possible that, there is a critical temperature of dissociation between iron and oxygen, although the critical points may vary in baths of different carbon content. Unfortunately, the accurate determination of the temperature of a molten bath at the time of pouring or teeming is a very difficult matter. For a long time I have been wishing that there were some reliable data which would indicate the effect of the tem-

Jan 12, 1913

By Alexander Coucoulas

FABRICATION of thin-film circuits deposited on glass substrates requires the formation of permanent electrical contacts. Since thin films are in the order of a few thousand angstroms thick and are deposited on nonconductive surfaces such as glass, new methods of lead attachment are being pursued in the microelectronics industry. Ultrasonic welding is being considered in thin-film technology since joining can be accomplished between a wide variety of dissimilar materials.l,' Ultrasonic welding is accomplished by a transducer-coupling-tip system which converts high-frequency electrical energy into mechanical vibrations and delivers it into the weld region. During the process the tip oscillates in a direction parallel to the surface of the weldments, inducing shear stresses in the work pieces which are clamped between the tip and anvil. Though the basic bonding mechanism is not clearly understood, it has been described as closely akin to friction welding. In the course of an investigation concerned with ultrasonic we!ding of aluminum wires to tantalum thin films (1400A) deposited on glass, low weld strengths were related to glass failure. Upon investigating this condition, an improved method of bonding was developed where the aluminum was held at a temperature where a minimum amount of strain hardening occurred during the introduction of ultrasonic energy. Experimental Procedure. Aluminum wires (0.015 in,) were bonded to tantalum thin films with an optimized set of welding parameters (power, time, clamping force) employing a commercial 100-w 60-kc ultrasonic welder. Forty-five degree shear-peel tests, where the lead is pulled at a 45-deg angle with respect to the substrate at 0.2 in. per min, produced a large variation from zero to the strength of the wire, Table I. Inspection of the weld region generally revealed: glass cracking before and after testing; the removal of glass nuggets from the substrate by the lead during testing, Table I; thin-film penetration. In an effort to improve the shear-peel strength, the aluminum between the tip and substrate was heated above ambient temperature through an argon gas media prior to and during welding with the same parameters employed above. With the addition of heat: wire deformation was increased; shear-peel tests all failed at the weld-wire junction, leaving the bonded portion undisturbed; no evidence of glass cracking or film penetration prior to or after testing was observed. In order to prevent failure at the weld-wire junction due to excessive wire deformation, 0.035-in. aluminum wires were welded to tantalum thin films with an optimized set of welding and heating parameters. As

Jan 1, 1967

By P. H. Delano, Will H. Coghill, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By Will H. Coghill, P. H. Delano, G. D. Coe

Data concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as " grindability-index numbers," but grind-ability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pull'erized product by a method comparabLe with- commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulvcrizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation,it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-¾-inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horsepower-hours." The channel-roller pulverizer hereinafter described is believed to meet these requirements. History oF the Machine The, work started when Ralph W. smith, engineer, St. Genevieve Lime Co., St. Cenevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasive-ness of dentifrices,1 and it was thought the same principles might be applied to coal, Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By Michael H. Kuryla, Galen H. Clevenger

Some years after Nobel made his epoch-making contribution to the knowledge of high explosives, Sprengell described a new class of detonating explosives consisting of mixtures, made immediately before use, of an oxidizing agent and a combustible substance.2 The novel feature of the Sprengel explosives is that the constituents alone are non-explosive during manufacture, storage and transport. Despite this advantage, and although some of these have been used in important work, they are now little used, possibly on account of the greater inconvenience to the user, compared with explosives supplied by the manufacturer in final form. Liquid-oxygen explosives are a type of Sprengel explosive in that the oxidizing agent (liquid oxygen) and the combustible substance or substances (solid carbonaceous matter alone or in combination with liquid hydrocarbons or even metallic powders and, at times inert absorbents) are brought together immediately before use. The components separately are non-explosive. The possibility of using liquid oxygen as one of the components of an explosive was perhaps first suggested by Sprengel, who stated that the beau ideal of a detonating explosive was a mixture of eight parts of liquid oxygen with one part of liquid hydrogen. Although the liquefaction of air3 had been accomplished in the laboratory as early

Jan 1, 1923

By Michael H. Kuryla, Galen H. Clevenger

Some years after Nobel made his epoch-making contribution to the knowledge of high explosives, Sprengell described a new class of detonating explosives consisting of mixtures, made immediately before use, of an oxidizing agent and a combustible substance.2 The novel feature of the Sprengel explosives is that the constituents alone are non-explosive during manufacture, storage and transport. Despite this advantage, and although some of these have been used in important work, they are now little used, possibly on account of the greater inconvenience to the user, compared with explosives supplied by the manufacturer in final form. Liquid-oxygen explosives are a type of Sprengel explosive in that the oxidizing agent (liquid oxygen) and the combustible substance or substances (solid carbonaceous matter alone or in combination with liquid hydrocarbons or even metallic powders and, at times inert absorbents) are brought together immediately before use. The components separately are non-explosive. The possibility of using liquid oxygen as one of the components of an explosive was perhaps first suggested by Sprengel, who stated that the beau ideal of a detonating explosive was a mixture of eight parts of liquid oxygen with one part of liquid hydrogen. Although the liquefaction of air3 had been accomplished in the laboratory as early

Jan 1, 1923

By R. W. Woodward, G. K. Burgess

minum bronze. Nearly all copper-base alloys are improved by rolling processes, but the copper-aluminum alloys seem to possess equally good properties when cast or rolled; this is a remarkable metallurgical fact. Another important property of these copper-aluminum alloys is their resistance to alternating stress. Many tests indicate that their resistance is greater in this respect than that of some steels, and I have seen instances when cast aluminum-bronze bolts have outlived five steel bolts in foundation work subject to severe shocks. I mention these various instances to indicate that work originally started as research for substitution of one material for another frequently develops 212 article which has properties not possessed by the original metal or alloy. I have dwelt particularly on the aluminum bronzes because recently I have done more special work on them than on other alloys, but I believe that the use of aluminum itself, in many combinations of metals, is a very important subject for investigation. Undoubtedly, after the war, the cost of aluminum will be reduced from its present price, and considering its low specific gravity it offers a very interesting and important field for research in the non-ferrous business. Naturally, if combinations containing aluminum can be developed in view of a probably increasing supply of metal, the cost will be reduced. This will benefit the industry generally and will immediately conserve tin. Bronzes, Bearing Metals, and Solders G. K. Burgess* and R. W. Woodward,† Washington, D. C.— From a metallurgical standpoint, there are several ways in which a reduction of the tin consumed in commercial non-ferrous and white-metal alloys can be effected. First, a reduction of the tin content of the alloy; second, substitution of part or all of the tin content by some other metal; third, a substitution of a different type of alloy, which in some cases also involves a change in mechanical design. The Bureau of Standards has been studying these methods of conservation for tin alloys, particularly in regard to babbitts and bearing metals, bronzes, and solders. Much of the information sewed by the Bureau was obtained from answers to questionnaires sent to manufacturers and users of these materials, so that, in general, any of the following suggestions or recommendations can be considered as being practical and as having already been thoroughly tried. Bearing Metals There is no question that the tin content of nearly all bearing metals can be reduced to some extent, and in some cases actually eliminated

Jan 1, 1919

By C. O. Ensign

Results of the application of geo1ogic knowledge to grade control have been remarkable. Grade reduction from dilution has been diminished from greater than 9% at the time of the program's beginning to about 2% at present. This has resulted in an increase of about 1.8 lb of copper per ton of ore mined and has made a substantial contribution to earnings at White Pine during the past two years. Even more improvement is expected in the future. The White Pine orebody, situated in the southwestern portion of the Keweenaw peninsula of upper Michigan, is a gently dipping stratiform or bedded deposit. Copper distribution is stratigraphi-cally controlled with higher values being confined to specific beds in the ore column. Room-and-pillar mining is practiced. Mining technique and geologic characteristics present a special array of problems in controlling the grade of ore. A routine program of grade control was started in the White Pine mine in August 1961. The program is based upon development and application of geologic knowledge to assist mine operating personnel to increase the grade of ore, primarily by accurate stratigraphic control and selection of areas for development on the basis of grade distribution trends. Geologists work closely with mine supervisors to offer the necessary geologic guidance. STRATIGRAPHIC POSITION OF COPPER The important rock series in the White Pine area is comprised of three formations of late Precambrian age. In descending order they are the Freda sandstone, Nonesuch shale, and Copper Harbor conglomerate. The Nonesuch shale is about 600 ft thick. Economic copper concentration occurs only in the lowermost 20 to 25 ft of the formation; however, within a restricted area along the southwest side of the mine the uppermost 1 to 7 ft of the Copper Harbor conglomerate (lower sandstone) contain sufficient quantities of copper to be included in the ore column. The ore consists primarily of chalcocite with subordinate native copper disseminated in shales, siltstones, and sandstones. MINE BOUNDARIES AND STRUCTURE The mine area is bounded on the west by the sub-outcrop of basal Nonesuch at bed rock surface and on the southwest by the White Pine fault (Fig. 1). The south and southeast limit of the orebody is reasonably well delineated by thinning or pinch-out of favorable host beds. Northern, northeastern, and eastern limits have not been established. The White Pine fault is actually a wide zone of shearing which strikes approximately N 40° W. It is downthrown on the southwest side and dips steeply to the northeast. Maximum vertical displacement is about 1500 ft.

Jan 1, 1964

Located 19 km (12 miles) north of the Carlin gold mine and 43 km (27 miles) north of Carlin, Nevada, is Carlin Gold Mining Company's Bootstrap mine. This deposit is similar in character to the Carlin ore, except it occurs in the upper plate formation of the Roberts thrust fault rather than in the lower plate rocks. The deposit was discovered over 50 years ago and operated on a small scale in the early 1960s using vat cyanide leaching. Newmont Mining Corporation acquired the property in 1967, and from an open pit mined 650,000 mt (717,000 st) of ore which was trucked to the Carlin conventional cyanide plant. (See Gold and Silver Cyanidation Plant Practice by F. W. McQuiston, Jr. and R. S. Shoemaker, Society of Mining Engineers, AIME, 1975. ) With the same grade of ore, the gold recovery by conventional methods is somewhat lower than that of the Carlin ore, even with a finer grind. Leaching tests were first conducted by the United States Bureau of Mines in 1968; and in 1971, ‘72, Carlin conducted extensive cyanidation investigations by bottle testing, simulated heap leaching in tall columns, and small scale pad heap leaches. Gold extractions ranged from 55% to 95% with low reagent consumptions. In 1974, a 545 mt (600 st) heap leach test was made at Carlin on pit-run low-grade material assaying 1.37 g per mt (0.04 oz per st). In a six week period the extraction of gold was 47.57'0. Carlin uses atomic absorption analyses on cyanide leach liquors to determine potential leach ore grade rather than fire assaying because it gives a more practical assessment of leach recovery than does fire assaying, which accounts for the total gold content. Before open-pit mining was started, plans were made to heap leach, the ore at Bootstrap which was too low grade for transport to Carlin. The topsoil outside of the designed pit area overlaid ancient lakebed clays which were found suitable for compaction to form an impervious base on which the dumps to be leached could be placed. By using the cost of truck haulage and milling at the Carlin plant and the price of gold 'at that time, a cutoff grade was established which resulted in the gold content of the first 150,000 mt (165,000 st) of the heap leaching ore being 1.51 g per mt (0.044 oz per st). An additional 500,000 mt (552,000 st) of lower grade material, assaying 0.96 g per mt (0.028 oz per st), is available for leaching as economics permit.

Jan 1, 1981

By Nathaniel Herz

The use of zinc dust for precipitating the pecious metals from cyanide solutions is well established now in many places, and has many advantages over the shavings method of precipitation. Although much work has been done o,n methods of testing zinc dust, as yet. no absolutely positive test has been devised to determine the value of the material. Certain facts are known, but often it happens that results on a working scale are not as expected from the laboratory tests. The purpose of this paper is to record some obscrvations made while testing a large variety of zinc-dust samples in the laboratory. W. J. Sharwoodl has described standard analytical methods, which have been followed, with the changes noted. The regular determinations include zinc oxide, by solution in ammonia and ammonium chloride, lead, and precipitating efficiency. In some cases cadmium was determined by a method similar to that described by J E Clennell.2 I will discuss the precipitating-efficiency test in detail. The procedure is as follows: "A solution of potassium silver cyanide is prepared by dissolving 10 grams of silver cyanide (AgCN) and 5 grams of 99 %' potassium cyanide in a little water and diluting up to 1000 cc. It is then adjusted by addition of a little more XCN or AgCN until the solution indicates from 0.12% to 0.15% free KCN by titration with standard silver nitrate. The titration is best made by using a 10-cc. or 20-cc. sample, adding 1 CC. of 2 % potassium iodide, and a slight excess of ammonia, as the end point is then sharper. Or 15 grams of pure crystallized XAg(CN)2 may be dissolved in a liter of water and 1.5 grams XCN added. " Weigh out 0.5 gram zinc dust into a 300-cc. beaker. Add a few cubic centimeters of watcr and stir until zinc is well mixed, then pour in 250 cc. of the prepared solution, stirring vigorously. See that all lumps are broken up, and continue stirring for fully five minutes. Stir occasionally (at least every 10 minutes) until the end of two hours from the addition of the solution. Then filter upon an 11-cm. filter, wash precipitate thoroughly, sprinkle with test lead, wrap it carefully in the paper, place in a scarifier with about 20 grams test lead, burn paper cautiously in muffle, scorify five minutes, cupel at low temperature and weigh silver. Milligrams silver obtained from 0.5 gram zinc X 0.0606 = percentage precipitating efflciency."³

Jan 1, 1916

By L. D. Jaffe, D. C. Buffum

The importance of temper brittleness in alloy steels has long been realized in Europe. In the United States recognition of its importance has developed within the last several years. Many brittle failures encountered in parts made of alloy steel are undoubtedly attributable, wholly or in part, to temper brittleness. These failures have occurred particularly at low temperatures, under shock loading, and in the presence of notches, restraints and combined stresses. It has been almost universally accepted that plain carbon steels are not susceptible to temper brittleness. As a result, considerable effort has been expended in attempts to discover the manner in which alloying elements introduce temper brittleness. It is desired to raise the possibility that plain carbon steels are not only susceptible to temper brittleness, but are much more susceptible than alloy steels, in the sense that they embrittle much more rapidly. It is suggested that previous views, (that plain carbon steels are not susceptible), are based upon an erroneous interpretation of the experimental results. Interpretation of Previous Data For many years the standard criterion for susceptibility of a steel to temper brittleness consisted of comparison of the energy absorption, in a notched-bar impact test at room temperature, of specimens that had received two heat treatments.' One specimen (or group of specimens) was quenched, tempered, and quenched from the temper. The other specimen (or group) differed only in having received an embrittlement treatment, which might consist of a slow cool from the tempering temperature, or of an isothermal hold in the range 45w550°C subsequent to quenching from the temper. If the energy absorption of the specimen receiving the embrittlement treatment was lower than that of the specimen not given this treatment, it was said that the steel was susceptible to temper brittleness. If the energy absorptions were the same, it was said that the steel was not susceptible. Several investigators2J found that plain carbon steels showed negligible difference in energy absorption in such tests (at least when their manganese content was below 0.60 pct), and concluded that plain carbon steels are not susceptible to temper brittleness. Recently the deficiencies of the criterion mentioned above have been pointed out.'-= The criterion now generally used for susceptibility to temper brittleness retains the heat treatments used in the earlier scheme, but instead of the notched-bar impact tests being made only at room temperature, they are made over a range of temperatures, covering the transition from ductile to brittle fracture. If the transition temperature of the specimens receiving the embrittlement treatment is higher than those

Jan 1, 1949

JOHN W. BELL, *Montreal, Quebec, Canada (communication to the Secretary?). The test results in Mr. Taggart's paper will, I am sure, be recognized as a notable contribution, and of great assistance in the study of the performance of the Hardinge mill. I regret, however, being obliged to note that Mr. Taggart still retains. such confidence in the Kick-Stadler method of computing the ?relative mechanical efficiency" of crushing machines. The Rittinger-Kick graph submitted by Mr. Gates and the tests made at McGill University disclosed precisely the same fundamental defect in the Kick-Stadler theory. Consequently, I have been obliged to recalculate in terms of Rittinger surface units the results obtained in the 28 rock-crushing tests cited by Mr. Taggart, in order to find- out what the relative efficiencies really were. In order to show the large discrepancies between the Stadler and Rittinger R. M. R's, the most, efficient result disclosed by each method is represented by the number 100, and the R.. M. E.'s for the other tests have been recalculated on this basis. The results will be found in Table 1. Personally, I look forward to the time when we shall cease to talk about "relative mechanical efficiency" and merely refer to the "efficiency" of a crusher. All that is required to accomplish this is to agree on a standard method for determining the "crushing constant" of a given rock and a standard method for calculating the efficiency. The figures in the fourth column of Table 1 have been derived by assuming a constant of 2,000 for the quartzite crushed in the Yale tests. The Stadler method sometimes indicates changes in efficiency produced by, changes in operating conditions, as I pointed out in a paper describing rock-crushing tests made at McGill University. It is, however, not enough to determine that certain changes increase or decrease efficiency; surely it is equally important to determine the magnitude of these variations. By examination of Mr. Taggart's results, I have been obliged to conclude that the size of feed and amount of reduction greatly influence the Stadler R. M. E. figures, that they are positively misleading. It should be mentioned that since the majority of the tests have been made at the least efficient feed rates, and since, moreover, it is one of the evidently very important factors affecting efficiency, it is possible that different results might be obtained by a high-tonnage feed series, and that

Jan 8, 1917

By C. Zener, H. Nielsen, D. Van Winkle

THE internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. EXPERIMENTAL METHOD The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress. The general method of making such measurements, and of observing the temperature of the specimen during a measurement, has been described elsewhere.5,6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and 900 cycles per second. SPECIMENS The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alphabrass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n ½ where n is the mean number of grains per square millimeter. EXPERIMENTAL RESULTS This paper is concerned exclusively with the part of the internal friction that becomes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By J. H. Mallery, J. H. Keeler

THE crystal structure of Zral, the compound richest in zirconium (91.03 pct Zr by weight) in the system Zr-Al, has been found to be ordered face-centered-cubic. This compound is of particular interest, since it is encountered as the precipitated phase in potentially useful zirconium-rich alloys. It forms peritectoidally from body-centered-cubic zirconium and Zr,Al at about 975°C. The Zr-A1 constitution diagram has been reported by McPherson and Hansen.' For the primary determination a 100 g ingot was prepared by arc-melting in a water-cooled copper crucible under purified argon. The raw materials were crystal-bar zirconium (a purity of better than 99.7 pct) and spectroscopically pure aluminum. The ingot was double melted, examined metallographi-cally, and found to be quite uniform as shown in Fig. 1. The hardness of the as-cast button was VHN 390 to 445. A 20 mil diam specimen was prepared from annealed (900°C) filings of Zr,Al. The specimen was mounted in a 5 cm radius powder camera and an 8 hr exposure was taken using copper radiation with a nickel filter. The structure of the compound Zral was found to be ordered face-centered-cubic of the Cuau type, with an a,, value of 4.37220.003A. Its calculated density is 5.976e0.013 g per cu cm. The relative intensities for the lines were calculated using the formula 1+cos2 20 I oc----------------- • p • /F7 sin2 0 cos 0 1 + COS' 20 where----------------is the Lorentz polarization fac- sin2 0 cos 0 tor, p is the multiplicity factor, and F is the structure factor. The X-ray data are given in Table I. The compound has exhibited plasticity when present as particles in a matrix of a zirconium. During hot working at about 900°C, the compound has been found to deform plastically to the extent that some of the particles exhibit a length-to-width ratio greater than 4:1 as shown in Fig. 2. In answer to the discussion of ref. 1, McPherson and Hansen pointed out that the compound may be cold rolled and reduced as much as 33 pct. Zr,Al has also been found2 under certain conditions to precipitate in lamellar form at grain boundaries of the a phase of hexagonal-close-packed zirconium. Acknowledgment This work was carried out under Contract W-31-109-Eng 52 for the United States Atomic Energy Commission.

Jan 1, 1956

Rossiter Worthington Raymond, Ph.D., LL. D-1840 to 1918.-Dr. Rossiter W. Raymond, Past President, Honorary Member and Secretary Emeritus, died suddenly of heart failure at his home, 123 Henry'St., Brooklyn, N. Y., on the evening of Tuesday, Dec. 31, 1918. He was one of the founders of the Institute and its second President. A Memorial 'Service will be held on Monday afternoon, Feb. 17. James Douglas.- The Institute suffered a second very severe loss by the death of Dr. James Douglas, Honorary Member, Past President (having served as President for two years), and in three separate respects the greatest benefactor of the Institute: first, in raising funds by volun¬tary subscription and his own personal gifts to pay the Institute's share of the money owed on the land on which the Engineering Societies Build¬ing now stands; second, as original donor to Engineering Societies Library; and third, by his bequest of $100,000 for the maintenance of the library of the American Institute of Mining Engineers. A resolution regarding the death of Dr. Douglas was passed by the Board of Directors and at the meeting of the Institute on Sept. 4, 1918, in Colorado, at which time a memorial service was held in the thea¬ter of the Hotel Broadmoor, attended by about 400 members and guests. A copy of the resolution was prepared and sent to the family. A bronze tablet is now being prepared and will be placed in the Members' Room and unveiled at the February meeting. A biography and portrait of Dr. Douglas was published in the September, 1918, Bulletin. There is also placed in the Engineering Societies Library an oil portrait of Dr. Douglas which had his own approval and was presented by him. American Institute of Metals.--During the Spring of the year, plans were completed with the American Institute of Metals whereby this society became the Institute of Metals Division of the American Insti¬tute of Mining Engineers. This body was a dignified aggregation of metallurgists which had been in existence for about 11 years. A bronze tablet commemorating the American Institute of Metals is now being placed in the Members' Room of the Institute, and during the year 1919 the Bulletin will bear the following title: "Bulletin of the American Institute of Mining Engineers, with which is consolidated the American Institute of Metals." Visits to Local Sections.-During the year President Jennings made visits to six of the Local Sections, on three of which occasions he was accompanied by the First Vice-president and the Secretary. First Vice-president Goodale made five visitations and the Secretary made eight.

Jan 1, 1923

Discussion of the paper of Dorsey A. Lyon and Robert M. Keeney, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 2117 to 2149. C. D. WOODWARD, Butte, Mont.:-We constructed a small blast furnace, and used first carbon electrodes and an alternating current of about 50 to 75 volts. We were able to smelt the material which was fed to the furnace, but we did not carry on experiments far enough to see just exactly what the power consumption was and compare it with the amount of material treated. We found that the blast seemed to help materially in reducing our charge and cutting down our power consumption. There were several other experiments tried at the time, and I do not call to mind now just what they were. We were trying to do away with the carbon electrode and replace it with an iron one, and it also seems to me we tried to use the ore for an electrode; but I believe that the electric furnace in the reducing end is simply a question of British thermal units per kilowatt-hour compared with British thermal units in a pound of coke. Now, if a pound of coke costs us 0.5 c. and a kilowatt-hour costs us in the neighborhood of 1.5 c., I think there is a big advantage in using coke instead of the electrical current for copper reducing. We tried steam, and a number of other methods, to throw copper down, but it has been some time ago and I am not very familiar with them now. The outlook of the experiments did not seem to be very promising, and we took it more as a thermal problem than an electrical one. PROF. JOSEPH W. RICHARDS, South Bethlehem, Pa.:-Mr. Woodward has spoken of the question as a thermal problem. I would call attention to the fact that electric furnaces usually utilize the heat of the electric current at from four to ten times the efficiency with which the heat generated by fuel is utilized; so it will not do simply to compare by thermal units generated. Your total thermal units may cost much less from coke than from electricity, yet you will find the electrically generated thermal units utilized in a properly designed furnace from three to ten times more efficiently than in the combustion furnace. You must make that allowance is comparing the cost of thermal units generated electrically and thermal units from coke.

Jan 11, 1913

By Charles H. Jacoby

In 1774 a Swedish chemist, C. W. Schule, first recognized manganese as an element. That same year Schule's associate, J. G. Gahn, isolated the element manganese for the first time. In 1856 the Bessemer process of steelmaking gave birth to the economic importance of manganese. Later, in 1882, Robert Hadfield discovered high manganese steels. Although the primary use of manganese is in the ferroalloy industry, two additional important uses for manganese are making chemicals and dry cell batteries. Manganese is also vital to plant and animal life. Various chemical compounds of manganese are used in fertilizers, feeds, glass manufacture, paints, varnishes, and for numerous medicinal and chemical purposes. For the study of industrial minerals and rocks, only the chemical and battery grade material is of concern, but for the sake of comparison, metallurgical aspects are included in this presentation. Although currently the world's largest consumer of manganese, the United States is producing only minor amounts of ore at the present time. This is due primarily to the fact that although huge deposits of manganese occur within our borders, all are of such low grade as to be economically unfeasible to mine. For many years various government agencies and segments of private industry have devoted sizable sums of money and time in an attempt to upgrade ores from the various deposits, and also in an attempt to recover manganese from blast furnace slags. In view of current world prices, and the quantity of high grade material available, there is little likelihood that any of these approaches will be found to be economically feasible in the near future. Geology and Mineralogy Mineralogy There are over one hundred minerals that contain manganese. These minerals vary from those with compositions that are predominantly manganese to those having only minor percentages. [ ] Geology From a geological standpoint most manga¬nese deposits are complex. In general, it can be said that all primary deposits of manganese are carbonates or silicates. The most productive and profitable have been those of sedimentary origin and residual concentrations. Examples of these residual types of deposits are associated with the metamorphosed lodes of Madhya, Pradesh, India, and the lateritic deposits of Orissa and Bihar, India; nodules in the residual clays of the Philippine Islands, U.S. southern Appalachians and Arkansas, Ghana, and Brazil. Sedimentary manganese deposits are best exemplified by the Nikopol district of Russia and the Tchiatouri area of Georgia, USSR. Hydrothermal replacements are characterized by the rhodochrosite deposits of Butte and Phillipsburg, Mont. In general, the hydrothermal type deposit has not resulted in any large tonnages being produced, but may have given

Jan 1, 1975

By Coleman D. Hunter, George M. Straughan

Oil and gas development as well as extensive leasing in Kentucky during 1940 has shown a marked improvement over the past three years.$ The most noticeable improvement is the gas development in eastern Kentucky and the deep tests being drilled by major oil interests. In western Kentucky, 406 wells were drilled, of which 173 were oil producers, 12 were gas wells and 221 were dry or abandoned. The number of dry tests was large, because no important, new oil or gas pool was discovered and many of the dry holes could be considered wildcat tests. However, with either oil or gas possibilities from Pennsylvanian formations on through Mississippian, Silurian, Devonian, and Ordovician, this percentage of dry holes seems rather high. Many of the dry tests possibly should have been tested in deeper horizons before being abandoned: namely, Silurian and Ordovician ages. In eastern Kentucky, 213 wells were drilled, of which 113 were gas producers, 61 were oil wells, and 39 were dry holes. Of these wells, 117 were drilled in the most important Big Sandy gas field, in Floyd, Pike, Knott and Martin Counties, and of this number 103 were gas producers, 5 were oil wells, and 9 were dry holes. In the Big Sinking oil field of Estill, Lee and Powell Counties, 70 of the remaining 96 wells were drilled, j6 being oil producers. During 1940, four deep tests were drilled in eastern Kentucky. One test penetrated the Knox dolomite in Knox County and was dry; no St. Peter sand was encountered. Another test in Lee County had some gas in what might be called St. Peter sand, according to the State Department, and also some gas deeper in the Knox dolomite. In Wolfe County, a small oil well was completed in the Ordovician, which was undoubtedly of Trenton age. ilt the present time, four deep tests are being drilled, all of which will go to the Knox dolomite. In Elliott County, on the Burke dome, the Inland Gas Co, is drilling at 3650 ft. In Magoffin County, on the Paint Creek uplift, the Cumberland Petroleum Co. is drilling at 3800 ft. In Clark County, in the Ruckerville fault area, W. 0. Allen is drilling at 1800 ft. In Laurel County, on the Sinking Creek dome, the Globe Oil and Gas Co. is drilling at I750 ft. If production is encountered in the Trenton, St. Peter, or Knox dolomite in any of these tests, eastern Kentucky will experience a marked increase in deep development.

Jan 1, 1941

By George M. Straughan, Coleman D. Hunter

Oil and gas development as well as extensive leasing in Kentucky during 1940 has shown a marked improvement over the past three years.$ The most noticeable improvement is the gas development in eastern Kentucky and the deep tests being drilled by major oil interests. In western Kentucky, 406 wells were drilled, of which 173 were oil producers, 12 were gas wells and 221 were dry or abandoned. The number of dry tests was large, because no important, new oil or gas pool was discovered and many of the dry holes could be considered wildcat tests. However, with either oil or gas possibilities from Pennsylvanian formations on through Mississippian, Silurian, Devonian, and Ordovician, this percentage of dry holes seems rather high. Many of the dry tests possibly should have been tested in deeper horizons before being abandoned: namely, Silurian and Ordovician ages. In eastern Kentucky, 213 wells were drilled, of which 113 were gas producers, 61 were oil wells, and 39 were dry holes. Of these wells, 117 were drilled in the most important Big Sandy gas field, in Floyd, Pike, Knott and Martin Counties, and of this number 103 were gas producers, 5 were oil wells, and 9 were dry holes. In the Big Sinking oil field of Estill, Lee and Powell Counties, 70 of the remaining 96 wells were drilled, j6 being oil producers. During 1940, four deep tests were drilled in eastern Kentucky. One test penetrated the Knox dolomite in Knox County and was dry; no St. Peter sand was encountered. Another test in Lee County had some gas in what might be called St. Peter sand, according to the State Department, and also some gas deeper in the Knox dolomite. In Wolfe County, a small oil well was completed in the Ordovician, which was undoubtedly of Trenton age. ilt the present time, four deep tests are being drilled, all of which will go to the Knox dolomite. In Elliott County, on the Burke dome, the Inland Gas Co, is drilling at 3650 ft. In Magoffin County, on the Paint Creek uplift, the Cumberland Petroleum Co. is drilling at 3800 ft. In Clark County, in the Ruckerville fault area, W. 0. Allen is drilling at 1800 ft. In Laurel County, on the Sinking Creek dome, the Globe Oil and Gas Co. is drilling at I750 ft. If production is encountered in the Trenton, St. Peter, or Knox dolomite in any of these tests, eastern Kentucky will experience a marked increase in deep development.

Jan 1, 1941