Search Documents

By Kenneth A. Moon

Kenneth A. Moon (U.S. Army Materials Research Agency)—The authors are to be congratulated for a very interesting and valuable paper. Their discussion of the structural implications of the results shown in their Fig. 5, however, requires a small correction. The model of Speiser and Spretnak with 0 = 1 and z' = 2 is perfectly reasonable for the Ti-O a phase, but Eq. [3] is valid only for solutions sufficiently dilute that the number of empty sites excluded by more than one filled site is negligible. The composition at which intrinsic saturation occurs therefore cannot be deduced from Eq. [3], but but must be decided by consideration of the structural details of the phase in question. In this case, intrinsic saturation is expected not at the composition Ti3O but at Ti2O, because Ti2O has the anti-Cd structurel4 for which each filled octahedral site has two nearby empty sites, one in the hexagonal plane immediately above it, and one in the similar plane below it. The other two models, with ?=1/3 and 1/2, imply a distinction between octahedral sites in pure titanium which is not easy to justify. The problem of extending Speiser's and Spretnak's treatment in a general way to more concentrated solutions will be the subject of a forthcoming publication by the writer. M. T. Hepworth and R. Schuhmann, Jr. (authors' reply)—The authors wish to thank Dr. Moon for calling to their attention the paper by Holmberg which presents the results of X-ray studies of Ti-O solutions ranging from 0 to 33 at. pct 0 and quenched from various annealing temperatures between 400" and 1800°C. Within these ranges, Holmberg found three types of phases: 1) At high oxygen contents (above 25 at. pct) and low annealing temperatures, he found the anti-Cd(OH)2 structure referred to by Dr. Moon. In this structure each titanium atom is in contact with 3 oxygens and each oxygen is in contact with 6 titaniums, the "available" oxygen sites corresponding to every other layer of octahedral sites in the titanium matrix. The limiting composition is Ti2O. However, this anti-Cd(OH)2 structure was not observed for samples containing 25 at. pct 0 or less. 2) For the specimen containing 25 at. pct 0 annealed at 400°C an ordered Ti3O structure was observed. This structure is related to the anti-Cd(OH)2 structure but differs from it by providing only two oxygens adjacent to each titanium atom and thus is consistent with the model represented by Eq. [5] in our paper, with 6 = 1/3, z' = 0. 3) For dilute solutions and for more concentrated solutions annealed at higher temperatures, the structure corresponds to that of the metal with random distribution of oxygens among all the octahedral sites. Thus, it is interesting to observe that the thermo-dynamic indications of ordering in the vicinity of Ti3O can now be supported qualitatively at least by Holmberg's X-ray evidence of the existence of an ordered phase of the composition Ti3O. That is, for solutions with oxygen contents close to that of Ti3O, both the thermodynamic data and the X-ray data are more consistent with models based on the ordered structure of Ti3O than they are with the model which Dr. Moon suggests corresponding to "intrinsic saturation" at Ti2O.

Jan 1, 1963

By JESSE L. MAURY

DEVELOPMENT of new gold mines in Canada since the price of that metal was increased in 1932 and 1933 has been of interest and importance to many of us. The day-by-day story has given an impression of aggressive effort and enough good luck so that the spirit of enterprise has been encouraged. It is the purpose of this article to report the results of a statistical appraisal which give emphatic numerical confirmation to this impression, together with certain side lights on the costs of development and equipment of new mines. The data presented have been taken from all readily available published sources up to the close of 1938 and are representative of that year. A. B. Bower did a large part .of the spadework and Weston Thomas offered many helpful suggestions.

Jan 1, 1939

By E. V. Kleber, V. F. Novy, R. C. Vickery

The constitutional diagram for the gadolinium-cobalt system has been determined. Seven intermetallic compounds have been found at compositions corresponding to the follwing gadolinium-cobalt ratios: 3:1, 1:1, 2:3, 1:2, 1:3, 1:4, 1:5. The GdCor compound has a congruent melting point above 1600°C. whereas the remaining compounds melt incongruently. Eutectics exist at 16 wt pct Co and 84 wt pct Co, with melting points of 620° and 1260°C, respectively. PREVIOUS papers'" have recorded constitutional data for systems of gadolinium with iron and nickel. This paper presents data obtained on alloys of gadolinium with the remaining 3d transition element-cobalt. voge13 found that cerium forms, with cobalt, the intermetallic compounds; Ce3Co, CeCo, CeCo2, CeCo3, CeCo4, and CeCo5 Other workers4-' found the 1:2 compound in this series to exist in a C-15 (face-centered cubic) structure and the 1:5 compound to exist in a hexagonal crystal system. Comparison of earlier data with that now reported will be made subsequently. EXPERIMENTAL Methods of alloy preparation, annealing procedures, and experimental techniques have been previously reported.' The cobalt content of alloy specimens was determined volumetrically. RESULTS Microstructure—The alloy containing 10.5 wt pct Co corresponds closely to the composition of the first intermetallic compound Gd3CO. In Fig. 1 the microstructure is essentially single phase composed of Gd3Co which formed peritectically. The globular areas are remnants of the peritectic reaction which did not quite go to completion. A eutectic occurs between Gd3Co and the next higher compound GdCO, which is followed by a series of peritectic compounds. Fig. 2, an arc-cast alloy containing 20.2 wt pct Co, shows large primary crystals of GdCo etching either white or black (depending on crystallographic orientation), embedded in the eutectic. Similarly, in Fig. 3 at 31.2 wt pct Co, a compound, probably GdCo3, has separated from the melt. Subsequent peritectic reactions were almost completely by-passed as the alloy cooled, the residual liquid freezing as a fine eutectic. In the 47.5 wt pct Co alloy, Fig. 4, the high melting point compound, GdCO4, has solidified as massive, white-etching grains, which reacted with the liquid to form GdCo3 as the second phase. The microstructure of an arc-melted alloy containing 60.5 pct Co is complex, Fig. 5, and presents some difficulty in interpretation. The grey etching matrix is probably primary GdCO4. The dappled phase represents grains of GdCO5 which have separated from the melt on cooling. The discrete spots in this phase are eutectic liquid. Small light etching crystallites are probably GdCO5 formed by the incomplete high-temperature peritectic reaction. GdCO4 is retained in arc-melted specimens containing 70.5 wt pct Co, Fig. 6. White areas of this compound are held in a matrix of GdCO5 the appearance of which is mottled slightly by inclusions of the second eutectic in this system. The development of the spheroidized eutectic at high cobalt contents is depicted in Fig. 7 (80.3 wt pct Co) in which the white massive crystals are GdCO5 compound. Further development of this eutectic is seen in Fig. 8, the primary white phase here being pure cobalt. Thermal Studies—Differential thermal analyses and melting point determinations have yielded the data shown in Fig. 10. The high gadolinium eutectic, indicated by microscopy, was confirmed at about 16 wt pct Co, melting at 620°C . A eutectic also occurs at about 84 wt pct Co melting at about 1260°C. The thermal arrests at 8803 960°, 1060; and 1210°C,

Jan 1, 1962

By W. F. Holbrook

THE problem of sulfur control is important in all blast-furnace operations but particularly for certain grades of steel because of the rigorous specifications. During the past decade the tendency has been to produce pig iron, and, hot metal of lower sulfur content. As most of the sulfur in the ion originates in the fuel, the use of high-sulfur coke demands modifications in practice to meet sulfur specifications. While it is generally known that high temperatures and more basic slags favor desulfurization, operators as a rule produce the most acid slag that will permit proper desulfurization. The viscosity of blast-furnace slag has been thought to be related to desulfurization and has been investigated by Feild and Royster1, also McCaffery and his associ-ates2, but apparently no systematic effort has been made to determine the relative desulfurizing powers of slags over the range of composition encountered in practice.

Jan 1, 1936

Jan 1, 1887

By Ashok K. Sinha

During the course of an in~*estigation into the occurrence of ordered AB3 structures, the following new phases have been found —CrRh3 (AuCu3 type), CrCo3 (MgCd3 type), HfCo4 (Ths Mn23 type), and WPt, MoPh type). The composition of the TiPt3-x phase (TiNi, type) is close to Ti23Pl77. The alloy chenzistry of transition rnetal AB3 structures is rezliewed in the light of electron concentration correlations of hex-agonality recently obtained for quasi-binary alloys. The relatizte colurne contraction in the AB3 structures increases with increasing difference in volume of the conzponents. A family of ordered close-packed layered structures is formed by stacking identical layers of composition AB, in various sequences, such that the coordination is twelvefold throughout and there are no A-A contacts. Previous work' on quasi-binary AB3 alloys has led to the conclusion that the stacking sequence of the AB, structures changes with increasing radius ratio RA/RB from a purely cubic, through different mixtures of hexagonal and cubic stacking to a purely hexagonal stacking. However. for binary AB3 alloys, a correlation between the type of the crystal structure and the position of the components in the various volumns of the periodic table has been noted.2-5 It has been noted6 that this correlation appears to hold even though the radius ratio RA/RB may vary over a considerable range with the location of the components in the three long periods. Another study7" of several quasi-binary systems led to the conclusion that an increase in hexagonality of the stacking is associated with increase in the electron concentration e/a. as defined by the average per atom of the total number of electrons outside the inert gas shells. In apparent conflict with this conclusion, it is known that seven binary alloy structures isotypic with TiNi3 which is 50 pct hexagonal occur at a higher electron concentration (e/n = 8.5) than that (e/a = 8.25) for the 100 pct hexagonal MgCd3 type structure present in seven binary AB3 alloys. Table 111. In the present work, an investigation into the occurrence of binary AB3 structures in transition metal alloys was made, and a survey of binary AB3 structures is presented. EXPERIMENTAL The starting materials were pure metals of 99.9 wt pct purity. The alloys were arc-melted under partial pressure of argon and annealed in sealed silica capsules lined with molybdenum foil under argon at- mosphere. The total weight loss upon melting and subsequent annealing was always less than 1 pct and hence the alloys will be referred to by their intended (unanalyzed) compositions. Wherever the constitution permitted. the alloys were given a homogenizing treatment at 1200°C (3 days) prior to annealing. Unless otherwise stated all alloys were annealed at 900°C for 1 week and water-quenched. Sometimes the final annealing treatment was carried out on powders to accelerate the attainment of equilibrium. X-ray powder patterns were taken using a Guinier-de Wolff focusing camera (CuK, radiation) or an asymmetrical focusing camera (Co or CrK, radiation). For lattice parameter determination. internal silicon standards were employed. The intensity calculations were made using a Fortran IV program written by Jeitschko and parthe.9 RESULTS Twenty AB3 and three AB4 alloys were investigated. Table I lists the crystallographic data on some of the intermediate phases encountered in the present work. Table II contains the X-ray data for HfCo, (Th,,Mn,, type). The positional parameter, x. was assumed to be 0.378. the value for Th6Mnn2310 The X-ray pattern of ZrCo, was very similar to that of HfCo, and the previous structure determination of ZrCo, by Kuzma el al." was confirmed. Ordering in the alloy CrCo could be ascertained by the presence of only one weak super lattice line (101). the others being too weak presumably owing to the small difference in the scattering powers of chromium and cobalt. This line was observed in the X-ray pattern of powder from the massive sample annealed at 830°C (7 days) after the powder had been reannealed at 600°C (24 hr). The diffraction pattern of the powder similarly reannealed at 830°C (24 hr) contained only the lines due to a mixture of hcp and fcc Co(Crj solid solutions. Therefore, it appears reasonable to assume that O2 and/or N2 contamination which would be less likely to occur during the 600°C anneal was not responsible for the observed weak reflection. Also. this reflection cannot be identified with any of the strong lines of the neighboring s phase which is present in the Co-Cr system at higher chromium contents. The composition corresponding to the TiNi3 structure observed by Raman et al.12 in the two-phase alloy Ti,zt,, has been established in the present work as being between There was satisfactory agreement for the low-angle lines (up to d = 1.997A) between the observed diffraction pattern of TiCua and that calculated assuming the ZrAu, structure. as recently proposed by Pfeifer-et a1.I3 However. some of the superlattice lines. e.g., at d = 1.937 and 1.919A. predicted by the ZrAu, structure were not actually observed eve? though neighboring lines. at d = 1.947 and 1.986A. of comparable calculated intensity were present. The ZrAu

Jan 1, 1970

By C. S. Giggins, F. S. Pettit

The oxidation properties of Ni-Cr alloys with fine grains, coarse grains, and deformed surface layers have been studied at temperatures of 900" and 1100°C in 0.1 atm of oxygen. The oxidation rates of alloys containing between 10 and 30 wt pct Cr have been found to be dependent upon the grain size of the alloy. Finegrained alloys had smaller oxidation rates than coarsegvained alloys because of the selective oxidation of chromium at alloy grain boundaries. In this compositional range alloys with deformed surface layers behaved similar to fine-grained alloys due to recrys-tallization of the deformed surface layer. In the preceding paper1 it was found that during the oxidation of Ni-Cr alloys, the volume fraction of precipitated Cr2O3 could be greater at alloy grain boundaries than at other areas of the alloy surface. In the case of alloys with chromium concentrations equal to or greater than 30 pct,* the volume fraction of Cr2O3 *AIL compositions are given as weight percent unless specified otherwise. precipitated at grain boundaries and within grains on the alloy surface both exceeded the critical amount required for lateral growth of the Cr2O3 particles and the surfaces of these alloys were completely covered with a continuous, external layer of Cr203 during oxidation. However, in the case of alloys with chromium concentrations between approximately 5 to 30 pct, the volume fraction of precipitated Cr2O3 exceeded the critical value required for external scale formation only at grain boundaries.but not within the interior of the grains. Consequently, the surfaces of these alloys had external scales of Cr3O3 over the grain boundaries but internal Cr2O3 subscales with external scales of NiO away from the grain boundaries. Under these latter conditions, it was found that chromium could diffuse laterally in the alloy from those areas covered with an external layer of Cr2O3, i.e., grain boundaries, to areas where the Cr2O3 was present as a subscale. This diffusion of chromium resulted in an increase in the volume fraction of Cr2O3 precipitated in the sub-scale zone and continuous layers of Cr2O3 could be formed at the subscale front in these regions. For the alloys used in the previous studies,' continuous layers of Cr2O3 were formed on Ni-20Cr alloys in the subscale regions after approximately 30 hr of oxidation at 900°C. For shorter periods of oxidation, the Cr2O3 layer was semicontinuous with the continuous portion at the subscale front emanating from points where the Cr2O3 had been formed as an external scale over alloy grain boundaries. Some lateral growth of a Cr2O3 layer in the subscale region was observed on Ni-15Cr and even Ni-10Cr alloys but this layer was never continuous after 30 hr of oxidation. These results indicate that the selective oxidation of chromium in Ni-Cr alloys with chromium contents between 5 to 30 pct may be dependent upon the grain size of the alloy. Fine-grained specimens in this compositional range should have a larger fraction of the surface covered with external Cr2O3 than coarsegrained specimens and the subscale areas required to be sealed via lateral diffusion of chromium should be smaller. It is therefore to be expected that a continuous layer of Cr2O3 can be formed on alloys in this compositional range after short periods of oxidation providing the alloy grain-size is sufficiently small. bo studieS2,3 have established that the oxidation behavior of alloys can be significantly influenced by pretreatments which produce mechanically deformed surfaces. It has been found that deformed surfaces usually promote the selective oxidation of elements in alloys and it is believed that these effects are due to rapid diffusion of elements in the deformed layer. In view of the previous results,' which showed that alloy grain boundaries may play an important role in the selective oxidation of chromium in Ni-Cr alloys, deformed surfaces may promote the selective oxidation of elements in alloys as a result of the numerous grain boundaries formed on the alloy surfaces via recrys-tallization during heating to the oxidation temperature. The purpose of the present studies was to determine the effect of alloy grain size and surface deformation on the selective oxidation of chromium in Ni-Cr alloys at temperatures of 900" and 1100°C in 0.1 atm of oxygen. EXPERIMENTAL The average grain diameter of the alloys used in the previous studies1 was not less than 0.04 mm and alloys with compositions between 5 and 30 pct chromium had average grain diameters between 0.04 and 0.14 mm. Since the oxidation kinetics were already available for these relatively coarse-grained alloys, it was desirable to use these same alloys in the present studies. The surfaces of the alloys listed in Table I of the previous paper were deformed by using a Model F S.S. White Industrial Airbrasive Unit, which delivered a controlled mixture of 25 µ Al2O3 particles in a stream of dry air at high velocity against the surface of a specimen. The amount of surface deformation produced by this treatment was not determined but a re-crystallized layer about 15 µ thick was formed upon annealing deformed specimens. The grain size at the surface of the specimens was reduced to an average grain diameter of 0.01 mm by annealing the deformed specimens, i.e., grit-blasted,

Jan 1, 1970

University of New Mexico, Albuquerque, N M Requests for publications should be addressed to the Librarian of the University Papers of the Geological Series of the University are bound in volumes: Vol 1, vol 2, pt 1, and vol 2, pt. 2, and vol. 3 are out of print, but separates of the following papers may be had at a uniform cost of 25 cents each. Vol. 1? No. 1, Geology of the environs of Albuquerque (1898); 2, Occurrence of copper and lead in the San Andreas and Caballo Mountains (1898), 3, Geological reconnaissance in western Socorro and Valencia counties (1898); Geology of the San Pedro and Albuquerque districts (1898). , Vol 2: No. 1, Geology of the Albuquerque Sheet (1900); 2, Miscellaneous economic papers by Herrick (1900); 3, Geological reconnaissance in western Socorro and Valencia counties (1900); 4, Geology of the White Sands of New Mexico (1900); 5, Identifi¬cation of an Ohio coal measure's horizon in New Mexico (1900); 6, Cyanide process in New Mexico (1900). Vol. 3. No 3, The oil situation in New Mexico (1920), 4, Geology of Sandia Mountains (1922); 5, Oil and gas m New Mexico in 1923.

Jan 1, 1933

By Charles L. Harness

STRONTIUM is an essential constituent of celestite (strontium sulphate), of the rarer strontianite (strontium carbonate), and of a few very rare minerals. Celestite is the chief ore but strontianite is more valued except for making the purest strontium salts, because of its ease of processing. The public knows strontium mainly as the source of the red flame in fireworks but it has many other uses. PROPERTIES The celestite of commerce is a massive mineral of varying texture: coarsely crystalline, fibrous, bladed, very fine grained or earthy. The color varies greatly with the nature of the impurities but the purer specimens are light blue (Latin, caelum, sky) or white. The strontianite of commerce is a massive mineral, more or less coarsely crystalline. The color varies with the impurities. Distinctive characteristics are effervescence with acids, density (3.68 to 3.71), and crimson strontium flame. A typical British celestite before World War II analyzed: SrSO4, 96.55 pct; SrCO3, 0.17; BaSO4, 0.25; CaSO4, 0.54; MgCO3, 0.15; R20,, 0.90; Si02, 1.38.10 A German strontianite analyzed: SrCO3, 90.9 pct; CaCO3, 7.5; BaCO3, 0.1; Fe2O3, 0.05; A1203, 0.1; SiO2, 0.04; S, 0.1; P, 0.005.10 ORIGIN AND MODE OF OCCURRENCE According to Clarke,9 strontia forms about 0.02 pct of the crust of the earth and is present in most igneous rocks, but in smaller quantities than barium. Under certain conditions, large masses of celestite are deposited from sea water with anhydrite. The presence of large amounts of celestite in some saline deposits and its absence in others suggests that the deposition of celestite depends on whether certain as yet undetermined concentrations of sulphate and chloride ions are reached in the brines. The most extensive of these sedimentary deposits are those of the Keuper (Triassic) in England, of the Zechstein (Permian) in Germany, and of various Cretaceous formations in Texas, Arkansas, and Utah. Of the deposits of southeastern California and western Arizona,

Jan 1, 1949

[Trans. No. Place Date Vol. Page 1. Wilkes-Barre, Pa.*.. *May: '71.. 1 3 2. Bethlehem, Pa Aug. '71.. 1 10 3. Troy, N. I X Nov. '71.. 1 13 4. Philadelphia, Pa Feb. '72.. 1 17 5. New York, N. Y.*.... May, '72.. 1 20 6. Pittsburgh, Pa Oct., '72.. 1 . 25 7. Boston, Mass Feb., '73 1 28 8. Philadelphia, Pa.*.... May, '73 2 3 9. Easton, Pa Oct., '73 2 7 10. New York, N. Y Feb., '74.. 2 11] [ ]

Jan 1, 1925

By Renato G. Bautista, KNona C. Liddell

A model of the reaction of chalcopyrite, CuFeS2, with Fe3+ and with 02 is considered. Homogeneous solution phase reactions are assumed to be always at equilibrium throughout the dissolution of the mineral. The dissociation of USOb- and several complexation reactions involving cu2+, Fez+ and Fe3+ are incorporated in the model equations. The relative importance of Fe3+, 02, and H+ as oxidants and the role of solution equilibria are assessed and the implications for leaching practice discussed.

Jan 1, 1981

By F. W. Aul, R. C. Glenn

EXTRACTION techniques are of particular importance in determining size, shape an: crystal structure of particles smaller than l000Å in steels and other alloys. However, artifacts that can arise during the preparation of extraction replicas may lead to erroneous conclusions. The purpose of this note is to illustrate some of these artifacts and the misinformation that can result from their presence. An alloy of iron with 0.8 pct Cu was investigated in the following conditions: 1) Solution treated 3 days at 925°C in dry hydrogen and quenched in water. Aged in steps to precipitate copper, as follows: heated to 700°C, held 1 day; then furnace cooled to 50O°C, held 3 days; then furnace cooled to room temperature. 2) Solution treated 3 days at 925OC in dry hydrogen and furnace cooled to room temperature. 3) Solution treated 3 days at 925OC or 17 hr at 1100°C in dry hydrogen to dissolve all copper, then quenched in water. A normal parlodion dry-extraction technique was employed after etching the specimens with super picralP or with 2 pct nital. A wet-extraction method

Jan 1, 1962

By William B. Plank

FOR the third consecutive year, I have collected the data on enrolment and employment of graduates from the schools in. the United States and Canada that grant degrees in mineral technology. The data were collected in the same way as formerly; namely, by questionnaire, dated Jan. 5, 1935, and are therefore comparable with the figures reported for former years. This year, along with the names of the 48 schools in the United States and the six in Canada, are listed the courses offered and the degrees granted by each, school, together with the names of the professors in charge. The names and addresses of the four schools in Mexico are also given. The list is on pages 450-1, which should he valued as a directory by those interested in mineral technology education. So far as is known, this is the most complete and up-to-date list that has ever been published.

Jan 1, 1935

By T. A. Read, H. K. Birnbaum

Deformation of AuCd alloys having the 8 (orthorhombic) and (3" (tetragonal) structures occurs by the stress induced motion of twin boutdaries. A restoring force acts on displaced twin boutdaries as a result of internal energy increases in the volume through which the boundaries are displaced. The phenomonology of the twin boundary motion is described and a mechanism for twin boundary motion and the restoring force is proposed. A time-dependent stabilization behavior of the twin boundaries, which is observed after the twins are formed by the diffusionless phase transformations, is described. THE AuCd 8 phase (ordered bcc structure) exhibits a transformation to a phase having an orthorhombic structure, 8' (space group D'), for compositions in the vicinity of 47.5 at. pct Cd and to a phase having a tetragonal structure, 8" (point group 4/m, m,m), for compositions in the vicinity 50.0 at. pct Cd. Both transformations are diffusionless, occur on cooling at 60" and 30OC, respectively, and are crystallo-graphically reversible.' They are accompanied by an inhomogeneous deformation which was observed to be twinning in the low-temperature phase. 3'4 The transformations may occur by a "single interface" or by "multiple interfaces."5'6 In the "single interface" transformation, the twinned product phase consisted of two twin orientations as shown in Fig. 1. In the multiple interface transformation the product phase contained "domains" each of which contained two twin orientations, Fig. 2. Deformation of specimens containing transformation twins was achieved by motion of the twin boundaries. Releasing the applied stress resulted in the displaced twin boundaries returning towards their initial positions. This "pseudo-elastic" behavior of the boundaries varied with time after the formation of the twin boundaries by the transformation.

Jan 1, 1961

By P. K. Koh, H. A. Lewis, H. F. Graff

New data on the distribution of silicon between slag and carbon-saturated iron at 1600Oand 1700OC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1'700°C for slags containing up to 20 pct A12O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A12O3-SiO, slags over a range from zero pct Al2O3 to saturation with Al2O3, or CaO.2Al2O3. The upper limit of SiO2 is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/Al203 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al,O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al0 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al2O3 and of Al20,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO2 (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2. The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

By W. G. Sinclair

THE North Texas district presented in this paper includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Jack, Knox, Montague, Wichita, Wilbarger and Young. It corresponds with the Texas Railroad Commission's district No. 9. Table I conforms with the nomenclature of pools as designated by the Commission. Most of the oil and gas produced in this region, generally referred to as the Red River uplift, comes from the Pennsylvanian strata. In recent years, however, increasing amounts are being developed in both the Mississippian and Ordovician.

Jan 1, 1946

By W. G. Sinclair

The wartime momentum of exploration continued throughout the year 1945 despite the end of hostilities in mid-August. The table below illustrates drilling activity in the various categories: Completed wells. . . . . . . . . . . . . . . . . . . . . . . . 401 Wildcats.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Wildcat discoveries, oil.. . . . . . . . . . . . . . . . . . . 2 Wildcat discoveries, gas-condensate.. . . . . . . 4 Development wells.. . . . . . . . . . . . . . . . . . . . . .297

Jan 1, 1946

By P. W. Bridgman

DURING the war, the Navy undertook the construction, under my direction, of an experimental gun embodying features designed to lessen the cost and time of production. These experiments were initiated after representations as to their, desirability had been offered by myself, by the Naval Consulting Board, and by the National Research Council. The first drawings were made in June, 1917, and the experiment was completed in November, 1918. For the sake of clearness it will pay to recapitulate briefly the fundamental idea of gun construction. It is well known that if a hollow cylinder is subjected to internal fluid pressure, the maximum stress occurs in the inside layers, the outer parts carrying much less than their due share of the stress. This inequality of stress is more pronounced the thicker the walls of the cylinder. If such a cylinder is pushed to the elastic limit, failure in elasticity will take place long before the outer layers have reached the limit of their capacity. Economical use of the material would demand, however, that all parts of the cylinder reach the limits of their capacity simultaneously. This may be brought about, at least in cylinders of not too great thickness, by producing in. the inner layers an initial compression, and in the outer layers an initial tension. The effect of internal pressure is at, first to relieve the compression of the inside layers, while increasing the tension of the outside layers. If the initial stresses are properly distributed, all parts of the cylinder will reach their elastic limits simultaneously, thus giving a cylinder of maximum strength for its weight. In gun construction as hitherto practiced, this initial distribution of stress is produced either by winding the inner tube with wire, a common English practice, or by shrinking hoops over the inner tube, which has been the standard American practice. Either process is long and expensive, particularly with the larger guns, 12- or 14-in., which require

Jan 2, 1920

By G. W. Cullen

Niobium-tin has been prepared on insulating suhstrates hby simultaneous hydrogen reduction of gaseous niobium and tin halides. Stoichiometric material is greater than 98.8pct theoretical density, appears to he single-phase, and has a total impirity level less than 0.3 at. pct. Transition temperatures and lattice constants may he related to composition. Typical current densities in various fields and orientations are given. IT is known that Nb3Sn carries large current densities in high fields, 1 and exhibits an unusually high transition temperature2 and critical field.3 For these reasons high-field solenoids have been constructed of this material.4 Because of the emphasis on solenoid fabrication, much of the materials research has been directed toward development of wire geometries wherein the brittle Nb3Sn is supported by a more malleable metal or alloy. There are, however, basic studies and applications that can be carried out only on Nb3Sn supported by an insulator. Insulating substrates are desirable for a number of reasons: the substrate does not interact with applied or induced currents and fields; diffusion of metallic species into the de- posit is avoided, both during the preparation and during subsequent heat treatment; irradiated samples are not more active than the deposit itself. Unsupported Nb3Sn geometries may also be prepared by preferential chemical dissolution of the insulating substrate. This report describes the preparation and properties of Nb3Sn deposits on ceramic substrates. Experiments currently utilizing material prepared in the manner described in this report include the following: dependence of current-carrying properties on field strength and orientation 5,6 radiation damage,7,8 tunneling,9 thermal conductivity (substrate removed),1° microwave surface impedance," tube magnetization,6,12 resistivity as a function of temperature,13 and current density and transition temperature as a function of annealing.14 Possible practical applications include magnetic shielding, superconductor generators, and frictionless bearings. PREPARATION Methods for the deposition of elemental niobium and tin by hydrogen reduction of the gaseous metal halides have been known for some time,15,18 but only recently a procedure was developed in this laboratory17 for the codeposition of these two metals on a hotwire as the intermetallic compound, Nb3Sn. This method of simultaneous hydrogen reduction of the gaseous niobium and tin chlorides is used for the preparation of Nb3Sn On ceramic substrates. The procedure differs from that employed on a hot wire in that insulating substrates cannot conveniently be heated to temperatures greater than their surround-

Jan 1, 1964

By R. W. Nash, A. E. Schwaneke, V. R. Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western prophyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized - 2.5 + 1. 3-cm (- 1 + 1/2- in.) ores from the Kingston (0.9% Cu) and Centennial (1.6% Cu) mines of Upper Michigan. Concentrates of 4.0% and 7.5% Cu, respectively, were obtained at recoveries of 85 and 80% of

Jan 8, 1978