Search Documents

By M. C. Chang, J. Dasher

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to bene-ficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly —24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant. The three major problems encountered in this system became acute when the mine switched from track-mounted machinery to the more economical off-track equipment. The quality and uniformity of product declined, too much slime accumulated in the circuit, and waste pond disposal became highly impracticable. Lowering of Quality and Uniformity: Since the filter cake was not beneficiated in any way, addition of this material, which contained about 18 pct ash. would certainly lower the quality of metallurgical coal. Difficulties of handling the high-ash, high-moisture cake were compounded by the lack of adequate blending facilities at the mine, making it impossible to maintain uniform feed for the coke ovens. For a two-month test period, to verify the source of trouble, all filter cake was excluded from the metallurgical coal. The excluded filter cake was stocked in the yard. Slime Buildup: The moisture retained in the coarse coal products and the filter cake provided daily the only means of slime bleed from the circuit. As this bleed was not enough to offset the incoming fines in the raw coal feed, there was excessive buildup of slimes. To operate at all, it was necessary to purge the system each weekend by pumping all the solids from the thickener to a waste pond. The slimes built up during the week progressively increased the apparent viscosity and density of the circulating plant water, so that hydroseparators and hydrotator units had to be constantly adjusted. Uniformity, yield, and quality of the metallurgical coal suffered in consequence, and the filter cake ash and moisture contents increased from Monday to Friday. Limited Waste Disposal: Location of the plant does not permit unlimited waste pond area. Maintenance of a waste pond for the purpose of emptying the thickener during weekends became a costly burden that could not be tolerated. HOW THE PROBLEMS WERE SOLVED The flowsheet (Fig. 1) chosen to overcome these difficulties is considered the one most economical to install and operate. In a preliminary change made before the flotation circuit was installed, the cyclones and thickener were first operated in series, the overflow from the 3-in. cyclones, after flocculation, being discharged into the thickener and the thick-

Jan 1, 1960

By R. A. Ritter, J. P. Batycky

A numerical technique has been developed to permit estimating the pressure gradient associated with laminar flow of thixotropic liquids through long Pipelines. For this purpose the pipeline is divided into a number of radial and longitudinal increments within which rheological properties of the fluid may be considered as constant at any time. Then, provided only that the fluid flow curve is defined at every duration of shear, it is possible to predict the instantaneous pressure gradient at any cross-section along the pipeline for each desired flow rate and pipe size. The technique consists of an iterative integration of shear rate to establish the appropriate value of the wall shear stress at each location. Consistency of fluid in the increment is determined by the flow history of that increment, while the radial flow associated with variations in velocity profile is accounted for by adjusting the width and radial position of the increment. A number of pressure profiles, computed at each of several flow rates, provide a convenient basis for pipeline design and pump selection. INTRODUCTION In recent years considerable attention has been given to predicting pressure drop associated with the isothermal laminar flow of time-independent non-Newtonian fluids in pipes and annuli. 6,11,12 The approach generally has been to develop analytical relationships between flow rate and pressure drop based on simple constitutive models which hopefully provide an approximate description of the rheological properties of the fluid. Analytical solutions are highly desirable since the influence of all pertinent parameters can be readily determined. Unfortunately, however, this approach is restricted to simple flow geometries and- frequently leads to erroneous results due to inadequacies in the model. In certain cases a solution may be obtained through applying appropriate numerical techniques.l,14 For example, a digital computer program is available for predicting the velocity profile and pressure drop encountered by any Newtonian or time-independent non-Newtonian fluid flowing under laminar conditions in a cylindrical pipe or annulus.l In this paper the consistency behavior of the fluid need only be described in terms of basic rheological data. Analyzing flow systems involving fluids with time-dependent rheological characteristics is considerably more complicated since substantial changes in consistency may occur because of sustained shear action. This sensitivity to shear frequently persists for several hours. Consequently, variations in pressure drop and/or flow rate resulting from the aging process and addition of unsheared or partially sheared fluid to the system must be considered for purposes of pipeline design. This paper outlines a numerical method for predicting the transient and steady-state laminar flow behavior of a thixotropic liquid in a pipeline of arbitrary length (i.e., at a specified constant flow rate, the instantaneous pressure gradient may be determined at any time after start up and at any location along the pipeline). Several such pressure gradient profiles, computed at several flow rates, may be combined to produce a complete portrait of the system response. This flow portrait provides a reasonable basis for pipeline design and for selecting a suitable pump characteristic. TIME-DEPENDENT RHEOLOGICAL BEHAVIOR The most familiar time-dependent rheological properties are those exhibited by thixotropic liquids. Many of these materials, particularly thixotropic crude oils, generally display an apparent yield stress in that a finite pressure gradient is required to initiate flow. Then, under the influence of sustained shear at a constant shear rate, the consistency systematically decreases to some final limiting value. The shear stress obtained at

By R. C. Schmidt, B. E. Kennedy

The Mont Klahoyo magnetite deposit is located about 600 km (373 miles) northwest of Abidjan, Ivory Coast. During an exploration period ending in 1977 an international joint venture group investigated the deposit and proved reserves of 670 Mt (739 million short tons) grading 36% iron. The deposit occurs at the northeast end of the Baoubly-Kiriao chain of Precambrian iron formations with associated amphibolites, pyroxenites, and gneisses of the Liberian Shield. The ore body is represented by a highly metamorphosed banded quartz-magnetite iron formation with alternating beds of iron silicates and quartz-magnetite. Amphibolite-pyroxenites and sillimanite-cordierite-garnet gneisses form hanging and footwall rocks. The iron formation has been folded into an elongated, overturned 2-shaped major drag fold with axes trending and plunging approximately northeast. Beds are vertical or dip steeply to the southeast. The ore zone has an average thickness of 130 m (427 ft) and outcrops intermittently over a distance of approximately 5.5 km (3.4 miles). Based upon detailed studies of drill cores and the results of ore dressing test work, eight stratigraphic units, identified as K- 1 to K-8, are recognizable in the iron formation. Four interbedded units are low grade silicate zones (silicate facies) while the remaining quartz-magnetite units are oxide facies, representing the important Mont Klahoyo deposit ores. Ore-bearing "K" units are subdivided further into 11 ore types, based upon their specific lithologies, iron content, and concentration characteristics. Identification of these ore types proved particularly useful to mine planning and flowsheet design. A cap of oxidized material overlies the primary quartz- magnetite iron formation, but no enrichment has occurred. It is thought that the Mont Klahoyo iron formations were deposited chemically in a volcanic environment as a siliceous iron formation with volcanism the primary source of iron and silica. Metamorphism converted the siliceous iron formation to a coarse-grained, quartz-magnetite-silicate iron formation.

Jan 1, 1983

By B. Egeberg, H. B. Smith

Britannia metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375" I?., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later. The approximate analysis of the metal we investigated was 91 Sn, 7 Sb, 2 Cu, and the molten metal was bottom-poured into an iron mold yielding an ingot 7 3/4 in. wide by 11 in. long and % in. thick, the casting temperature being 800" F. The ingot was cold-rolled to a sheet 0.032 in. thick, sufficiently large samples for experimental purposes being cut from the sheet at intermediate stages. The samples were all tested for hardness with scleroscope and Brine11 machine, then heated to 212" F. for 30 min., and again tested after cooling to room temperature. The same samples were heated successively at 300°, 400°, and 440" F., followed

Jan 1, 1929

By H. B. Smith, B. Egeberg

Britannia metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375" I?., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later. The approximate analysis of the metal we investigated was 91 Sn, 7 Sb, 2 Cu, and the molten metal was bottom-poured into an iron mold yielding an ingot 7 3/4 in. wide by 11 in. long and % in. thick, the casting temperature being 800" F. The ingot was cold-rolled to a sheet 0.032 in. thick, sufficiently large samples for experimental purposes being cut from the sheet at intermediate stages. The samples were all tested for hardness with scleroscope and Brine11 machine, then heated to 212" F. for 30 min., and again tested after cooling to room temperature. The same samples were heated successively at 300°, 400°, and 440" F., followed

Jan 1, 1929

By D. F. Kaufman, E. D. Levine, L. R. Aronin

The deformation of' impure beryllium crystals by basal glide at room temperature invariably tevminates by basal cleavage after a few percent strain. It is generally accepted that .fracture of this type is caused by the splitting of low) -angle boundaries, or bend planes, by obstacles that restrict the motion of the bed planes in the deforming crystal. The details of such a process have been developed by Stroh, who showed that the high tensile stress norrnal to the basal plane in the region where the bend plane is split results in the propagation of a basal cleavage crack, provided there is no available dejorvrlatzon mode having a shear component normal to the basal plane It has been postulated that puvification of beryllium might lead to increased basal ductility by the vemoval of barviers to bend plane motion and possibly by the activation of nonbasal defor~rlation systems. Large increases in the amount of basal glide that can he sustained prior to fracture have been observed in crystals purified by zone refining. In each case, eventudal fracture was by sharp basal cleavage, suggesting that the split bend plane model still applies to tile fracture of beryllium of rensonably high purity. In the present work, calculations are made to show to what extent basal duetilits can be increased by purification while the split bend plane .fracture process remains applicable. Experimentally observed ductilities are generally somewhat lower than those predicted by calculation because of premature failure due to defects introd~cced during specimen preparation and testing. SEVERAL investigators1-4 have studied the deformation characteristics of beryllium single crystals of commercial purity, and have related the strong anisotropy of plastic deformation in single crystals to the problem of brittleness in polycrystalline beryllium. For most orientations, the principal deformation mode is basal slip, which, at temperatures between 300" and 900°K, begins at a critical resolved shear stress of approximately 1500 g per sq mm and terminates after 3 to 6 pet glide strain by cleavage on the basal plane in the neighborhood of (1120) bend planes that are formed during the deformation. This type of fracture, which is also observed in zinc at low temperatures, has been interpreted by stroh5 to be caused by the splitting of bend planes by obstacles to their motion. In the Stroh model, a (11.20) dislocation wall, or bend plane, moving along the slip direction under the action of the applied stress, encounters obstacles which cause part of the bend plane to be held up, the other part continuing to move. Stress concentrations are built up in the region where the bend plane is split, with a high tensile component normal to the basal plane, resulting in a microcrack at the end of the split wall. Because no deformation mode having a shear component at an angle to the basal plane is available to relieve the stress at the crack tip, the crack can propagate under a sufficiently high applied stress. The Stroh criterion for crack propagation is given by

Jan 1, 1964

By M. Tanaka, S. Kita, Y. Jinnouchi, Y. Sawada

This paper generalizes the results of the recent theoretical and experimental investigations on the air-pulsated jigs in Japan. The pulsating mechanism is analyzed as a special vibratory system, and the jigging mechanism as a mass system subjected to the law of hindered settling. The results of investigations on the following items are reviewed: dynamics of the pulsating mechanism; pulsation in a practical TACUB jig development of a new type of air valve; uniform pulsation in a large Baum jig; motion and mobility of bed particles; separating speed in hindered conditions; and standard deviation in practical jigs.

Jan 1, 1985

By Nathaniel Arbiter

THE separation of minerals by flotation can be regarded as a rate process, with the extraction of any one mineral determined by its flotation rate, and the grade of concentrate by the relative rates for all the minerals. So regarded, the significant variables for the process are those that control the rates. These variables are of two types, the first describing the ore and its physical and chemical treatment prior to flotation and the second characterizing the separation process in the cells. This paper will examine the variation in rates for a group of separations, will show that a simple rate law appears to govern, and will consider the relation of the control variables to the rates. The use of rate constants for evaluation of performance and efficiency will be discussed.

Jan 9, 1951

By H. P. Allen

The Achotla mill of the Cia. Minera de Penoles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1939

By H. P. Allen

The Achotla mill of the Cia. Minera de Penoles is of special interest in that it is one of the few still employing the chloridization process. The ore milled comes from the Suriana mine and consists of both oxide and sulphide, from neither of which can the gold or silver be extracted by a simple cyanide treatment. The mill was built in 1927, after several years of study in the development of the process1, and operated from December of that year until October 1930. Operations were resumed in February 1935, and have been continuous since, treating approximately 5000 tons per month, while the mine is getting up to full tonnage of 6500 tons per month. Transportation of Supplies The property is in Guerrero, Mexico, some 175 km. by airline southwest of Mexico City. The mill site is at Temisco (Fig. I), 8 km. from the Balsas River and 4.8 km. by aerial tram from the mine. At Temisco are the general office, shops, warehouses and laboratory serving both mine and mill. Here sufficient water is available either from a small creek running through the property or from the Balsas River, also convenient and ample storage space for the tailings. With the exception of the mine timber and a few native building materials which may be obtained locally, all supplies for both mine and mill are brought down the Balsas River from Balsas, the terminal of a Mexican National Railway line out of Mexico City. The method of transportation on the river is interesting. Rapids with very fast water are numerous, prohibiting the use of mechanically propelled boats. Those used resemble large, flat-bottomed rowboats some 22 ft. long by 8 ft. wide (Fig. 2). They are manned by two oarsmen sitting in the bow, each handling one large oar, and usually another man in the stern who, with his oar, assists in steering the boat, especially when the rapids are run. From 3 to 7 tons of freight are carried on each boat, depending upon the stage of the water, which governs also the time

Jan 1, 1939

By Charles F. Brush

THE compression of gases to a very high degree, for purposes of scientific research, has long presented serious difficulties to the physicist. Great advances have been made of late years in the construction of ordinary air or exhaust pumps, while very little has been done towards the improvement of compression pumps. The principal difficulties encountered in the construction of such apparatus are the existence of the so-called "dead space" in the pump barrels, leakage of the piston packings under high pressure, and the trouble arising from the unequal expansion of parts caused by the development of the latent heat of the gas during compression. Of these obstacles to success, the "dead space" is far the most serious, as it fixes a limit to the performance of the pump beyond which it is impossible to carry the compression. The writer having occasion, some time since, to make a series of investigations on gases very highly compressed, and finding no apparatus, or description of apparatus, adequate to produce the required

Jan 1, 1876

By Richard P. Rothwell

The anthracite coals of Pennsylvania are all mined from large veins. A seam less than four feet. in thickness is generally considered as unworkable, those from which most of the coal now comes being from 8 'to 30 feet thick. The system of mining employed is, almost without exception, that known as " chamber and pillar work;" that is, the coal is taken out of chambers of from 18 to 30 feet in width, and pillars of from 12 to 20 feet are left between these to support the roof. In general, the entire thickness of the seam, even

[¦Abad, Leopoldo F., College of Min., Univ. of California Berkeley, Cal. '23 ¦Abarquez, Ramon F., Met., Bureau of Science Manila, P. 1. '24 ¦Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd ...Concepcion del Oro, Zacatecas, Mexico. '23 Abbott, Clarence B., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co., 1405 Minnesota Ave., Bessemer, Ala.' '04] [ ]

Jan 1, 1925

By A. L. Bailey, B. A. Landry

W. W. ANDERSON and G. E. KELLER*—We want to compliment the authors on this very thorough paper. It gives information which the coal industry has needed for some time. We hope that the additional information which the authors are collecting will he available shortly. The mixing and riffling procedure that was followed for experimental purposes is obviously not practical in routine float-and-sink testing because of the particle size degradation which would result in handling the sample so many times. It is important to obtain our tloat-and-sink fractions with a minimum amount of handling of material. A statement is made in the paper (p. 80) that "the variable most likely to affect the size of sample required to meet a given preassigned accuracy would be the state or degree of mixing of the coal." We agree that this is a large factor, but do not believe it is the most important factor. Our own opinion is that the most important single factor governing the total gross weight of sample that must be collected is the percentage of the weight of material in the smallest fraction that results from the screening and float-and-\ink operations. In other words, size of sample is governed by the total number of fractionations that must he made, and the distribution of material within the fractions. We can imagine a coal with perfect mixing, but with such a small amount of material in some float-and-sink fraction in one of the coarse sizes that a much larger sample would have to be taken than would be the case with very poorly mixed material, but with a large percentage of coarse material more evenly distributed in all float-and-sink fractions. Our own observation of many float-and-sink tests that we have run in our own organization on many types of coal is that the size of sample that must be used on fine size float and sink is governed more by the requirements for weight of material to be used for analysis in the laboratory than by weight of material necessary to obtain accurate float and sink percentage of weight values. In other words, it is our opinion that very small samples can be used for float-and-sink fractionation in the fine sizes, but that accurate analysis of the fractions will depend on a larger weight of sample being pulverized for the laboratory than is necessary to establish the float-and-sink distribution with respect to weight. A. L. BAILEY and B. A. LANDRY (authors' reply)—The authors thank Messrs. Anderson and Keller for their comments based on long experience. It is agreed that the involved mixing and riming technique used may be disadvantageous from the standpoint of degradation. Fortunately, the paper does point out that the extended riming was unrewarding in causing further mixing. Two large unknowns remain, however: (1) how much of the mixing from the presumed highly unmixed state in the bed was achieved toward the random state during blasting, loading, transportation, screening, and further transportation to the point where the gross sample was taken, and (2) how much of the mixing took place during the preparation described preceding riming. As has been pointed out by one of the authors.6 the degree of mixing has a very large effect on the size of sample required and there are still too few experimental data to show at what stage of coal handling most of the mixing occurs. The discussion states that the weight of material in a screened fraction, or in a float-and-sink fraction, is more important than the mixing factor. We do not believe that these factors are comparable in this instance inasmuch as our purpose was to give minimum sampling requirements to achieve a preassigned accuracy in the percentages of float, middlings, or sink, and nothing more. The gross sample had already been screened and no further division by screening was made or contemplated; also, it was not intended that the middlings and sink fractions would necessarily be adequate for percentage ash or other determination. In other words, the sample obtained by the method outlined is not intended for washability studies but only for preparation plant control. Further experimental work has been done, since the paper was prepared, to investigate the effect of increasingly larger top and bottom sizes on the variability of float, etc., of a double-screened coal from Western Pennsylvania. Results will be published and eventually attention is to be given to the preparation of sampling specifications. E. H. M. BADGER*—I should like the authors to explain more fully the fundamental assumptions on which their Eq 4 is based. The equation is of the form s2 = p(l - p) which is the usual expression for the (standard deviation)2 when the chance of finding a particular kind of particle in the sample is proportional to the number fraetion, p. But instead of the number fraction, the authors have used the weight fraction, WF/W. The chance of finding a particular kind of particle in the sample can only be proportional to the weight fraction, if the average ?eig?ts of all kinds of particles, that is, float, midlings, or sink, are the same. Surely a much more justifiable assumption would be that the average volumes of the particles are the same, and, if this is so, Eq 4 would not be true. This may be demonstrated as follows: Let be the weight fraction of float, middlings, or sink, dl the density of this fraction, and d2 the density of the rest of the coal. Then assuming that the average volumes of the pieces in the three classes are the same, the number fraction, p, is given by ? P = d1/l-?/d2 + ?/d1 = ?d2/d1 + ?(d2-d1) The weight fraction, w, in terms of p is given by ? = pd1/(l-p)d2 + pd1 = pd1/d2 + p(d1-d2) _____ [61

Jan 1, 1950

By L. A. Willey

IN 1953, a method for filtering a liquid phase from solid phases while in equilibrium at elevated temperatures was devised at the Alcoa Aluminum Research Laboratories. Since then, it has been applied to the investigation of liquid-solid equilibrium in metallic systems. In application, the method simplifies the centrifuge filt.ration procedure as developed by Scheil and described by Gebhardt Fig. 1 shows a sketch of the filtering apparatus located within a thermal analysis furnace. It consists of a stainless steel filter crucible A, into the bottom of which a porous carbon filter disk B, 1 3/4 in. diam by 1/4 in. thick, is sealed to the shoulder and rim with carbonaceous cement. The base of the filter crucible, machined to an angle, fits into a tapered seat at the mouth of a stainless steel vacuum chamber C. A connecting tube from the vacuum chamber to a vacuum line also serves as a means for supporting the apparatus from the base of the furnace. An alundum crucible D of 25 ml capacity is placed with- in the vacuum chamber below the filter for collecting the filtrate. Two thermocouples E, in stainless steel protection tubes, which extend from 1/16 to in. above the center of the filter, are mounted on the rim of the filter crucible. One thermocouple is used in differential connection with the furnace control thermocouple to regulate rates of heating and cooling. The other serves as a means for recording the temperature of the alloy prior to filtering. A suitable mold coating is used on exposed surfaces of stainless steel parts to guard against attack upon these parts as well as to avoid contamination of the alloy samples. A mold wash prepared from precipitated CaCO, is suitable for aluminum alloys. The porous carbon for the filter disks and the carbonaceous cement, grade 200 (graphite base), were obtained from the National Carbon Co. Porous car-bon, grade Nos. 10 to 60, has been employed. Grade No. 40, however, appeared to give the optimum advantages in operation. In operation, an alloy sample is remelted and heated to about 50°C above its liquidus temperature. At the same time, the filter apparatus is preheated to about the same temperature. The alloy then is cast into the filter crucible.

Jan 1, 1957

By W. A. Ver Wiebe

Under the impetus of new demands caused by the war, the oil and gas industries of Kansas established new records during the year 1942. In all, 1513 test wells were drilled, which is somewhat of a drop from the figure of 2113 for 1941. The 1513 tests yielded 800 new oil wells, 85 new gas wells, and 628 dry holes. Thus there was an increase in two categories, the gas wells and the dry holes. Considering that last year only 592 dry holes were completed out of a much larger total, the figure of 628 dry holes causes some concern among local operators. The increase in unsuccessful tests illustrates once more the fact that each year it is becoming harder to find the remaining oil pools. When the figures are broken down, it appears that western Kansas accounted for 1177 tests, of which 689 were oil wells, 33 gas wells, and 455 dry holes. The total potential daily initial production uncovered by the successful wells amounted to 753,178 bbl. of oil and 619,734,000 cu. it. of gas. The figures for new initial production indicate a substantial drop from last year's figure of 1,691,000 bbl., and the figures on gas are slightly higher. In 1941 the new gas as based on a daily potential was 508,000,-000 cu. ft. In eastern Kansas, 336 wells were drilled. Among these in were oil wells, accounting for a daily initial potential production of 16,199 bbl. The new gas wells numbered 52 and added 253,725,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 173 in number, were dry. It is interesting and perhaps significant that about half (630) of the wells drilled in western Kansas were drilled by the independent operators. Among the large companies, the Cities Service Oil Co. drilled 163 wells; the Stanolind Oil and Gas Co., 52; the Skelly Oil Co., 39; the Continental Oil Co., 48; and the Shell Petroleum Co., 21 wells. In eastern Kansas the independent operators drilled 297 out of the total of 336 wells. Among the major oil companies the Cities Service Oil Co. drilled 19; the Phillips Petroleum Co. 7; and the Sinclair-Prairie Oil Co., 6 wells. The figures based on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas almost one half of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 547 wells in western Kansas, of which 379 were successful in finding either oil or gas. It thus appears that the major companies fared better than the independents. In eastern Kansas the major companies drilled 39 wells, of which 29 were successful in finding commercial quantities of oil or of gas. No less than 329 wildcat test holes were put down in western Kansas and 105 in eastern Kansas, or 434 in all, during 1942. Considerably more than half of these were drilled by independent operators; 223 in western and 99 in eastern Kansas. An exploratory hole 56 mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, about 80 per cent of wildcat wells were failures. In western Kansas only 20 per cent found either oil or gas. The failures were about equally distributed among the major

Jan 1, 1943

By W. A. Ver Wiebe

Under the impetus of new demands caused by the war, the oil and gas industries of Kansas established new records during the year 1942. In all, 1513 test wells were drilled, which is somewhat of a drop from the figure of 2113 for 1941. The 1513 tests yielded 800 new oil wells, 85 new gas wells, and 628 dry holes. Thus there was an increase in two categories, the gas wells and the dry holes. Considering that last year only 592 dry holes were completed out of a much larger total, the figure of 628 dry holes causes some concern among local operators. The increase in unsuccessful tests illustrates once more the fact that each year it is becoming harder to find the remaining oil pools. When the figures are broken down, it appears that western Kansas accounted for 1177 tests, of which 689 were oil wells, 33 gas wells, and 455 dry holes. The total potential daily initial production uncovered by the successful wells amounted to 753,178 bbl. of oil and 619,734,000 cu. it. of gas. The figures for new initial production indicate a substantial drop from last year's figure of 1,691,000 bbl., and the figures on gas are slightly higher. In 1941 the new gas as based on a daily potential was 508,000,-000 cu. ft. In eastern Kansas, 336 wells were drilled. Among these in were oil wells, accounting for a daily initial potential production of 16,199 bbl. The new gas wells numbered 52 and added 253,725,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 173 in number, were dry. It is interesting and perhaps significant that about half (630) of the wells drilled in western Kansas were drilled by the independent operators. Among the large companies, the Cities Service Oil Co. drilled 163 wells; the Stanolind Oil and Gas Co., 52; the Skelly Oil Co., 39; the Continental Oil Co., 48; and the Shell Petroleum Co., 21 wells. In eastern Kansas the independent operators drilled 297 out of the total of 336 wells. Among the major oil companies the Cities Service Oil Co. drilled 19; the Phillips Petroleum Co. 7; and the Sinclair-Prairie Oil Co., 6 wells. The figures based on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas almost one half of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 547 wells in western Kansas, of which 379 were successful in finding either oil or gas. It thus appears that the major companies fared better than the independents. In eastern Kansas the major companies drilled 39 wells, of which 29 were successful in finding commercial quantities of oil or of gas. No less than 329 wildcat test holes were put down in western Kansas and 105 in eastern Kansas, or 434 in all, during 1942. Considerably more than half of these were drilled by independent operators; 223 in western and 99 in eastern Kansas. An exploratory hole 56 mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, about 80 per cent of wildcat wells were failures. In western Kansas only 20 per cent found either oil or gas. The failures were about equally distributed among the major

Jan 1, 1943

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By William B. Senseman

FoR reasons well known to mining engineers, wet grinding is quite universal in plants having to do with the extraction of metallic values from crude ores. In the processing of the nonmetallic and industrial minerals, dry grinding is the more common method. The crude materials usually contain less moisture than is required for wet grinding and the products usually are marketed in dry form; most of them as powders. To grind wet, therefore, would entail the addition of water and an expense for drying the product, which is not justified. Furthermore, the material would be a dried cake that would still have to be pulverized or disintegrated before use. For producing fine products, air separators have largely replaced the earlier practice of sizing with screens and bolting reels. Mills in which the air-separating feature is an integral part of the design are now commonplace. Mill designs are many and air systems have developed along various lines, but for the purpose of this discussion, only the fundamental idea need be emphasized— the idea of using air for sizing and removing pulverized material from a grinding mill. About 20 years ago, when the use of mills equipped with air separation had become common practice, heated air or gas was introduced to such a system for the removal of moisture. The purpose of this discussion is to outline the developments and trends that have followed this experiment. It is an important development, for mills equipped with air separation are now universally used for pulverizing not only nonmetallic and industrial minerals, but a great variety of other materials. All such mills are essentially the same. Dried material is pulverized, removed by an air stream, trapped in a cyclone collector, and relatively clean air from the cyclone is returned through a fan to the mill. There is no theoretical need for a vent from the system. The practical need is to vent the air that leaks into the system; and, since the cyclone is not 100 per cent efficient as a dust collector, this vented air carries some dust with it. The initial attempt at drying was made on a system like that described, by the addition of a furnace. The minus pressure within the mill draws hot gas from the furnace. Infiltration air, along with the drying gases and evaporated moisture, is vented as before. The first application was made to a mill used for pulverizing coal. The coal contained very little moisture, so very little drying effect was needed for the success of this experiment. Actually, some calculated efficiencies of over 100 per cent were obtained before due allowance was made for the conversion of mill power into useful heat. When moisture is low, the heat obtained from the conversion of milt power is an appreciable part of that required. That drying can be effected in the short time interval available in a grinding mill of this type is better understood by visual-

Jan 1, 1948

By B. S. Butler

The principal ore deposits of Arizona are in the southern, cen-tral, and western portions of the state, which physiographically are part of the Basin and Range province, southwest of the Colo-rado Plateau (Pl. I). The Basin and Range province is characterized by numerous subparallel mountain ranges separated by plains or valleys. Most of these ranges trend northwest to north, parallel to the margin of the Colorado Plateau; but in southeastern Arizona, southern New Mexico, and northeastern Sonora, they trend northward, transverse too the edge of the Plateau. The mountains rise abruptly from plains or valleys, the margins of which in many places are pediments cut on hard rock. Some of the plains form closed basins (bolsons, playas), but most of them are drained. The Basin and Range province in Arizona is divisible into the Mountain Region and the Desert Region4 (Pls. I and II). The Mountain Region forms a belt 60 to 100 miles wide that contains most of the large ore deposits. Its longest range measures about 55 miles, the widest 20 miles, and the highest peak more than 10,000 feet above sea level or 7,000 feet above adjacent valleys or plains. Broad plain-forming valleys are exceptional, but several with maximum widths of 20 to more than 30 miles appear in the southeastern portion. In the Desert Region the mountains are relatively low, narrow, serrated, and steep, with sharply angular profiles. There are a few exceptionally large ranges of which the longest measures nearly 100 miles and the widest 18 miles. The highest peak is some 7,000 feet above sea level, and the maximum local relief amounts to about 5,400 feet. Broad and comparatively low desert plains form 50 to 75 per cent of the area.

Jan 1, 1939