Search Documents

By B. J. Shaw, R. Kossowsky, W. C. Johnston

High purity (99,95) Ni-51 wt pct cr eutectic alloy was unidirectionalty solidified at rates of 0.1 to 8 in. per hr. The resulting material was characterized by large grains, approximately 0.5 mm in cross section and extending through almost the entire length of the specimen, parallel to the growth axis. The eutectic structure of specimens the growth at -1/3 The per hr consisted of a continuous nickel-rich phase and chrome -rich lamellae approximately 2 thick, spaced about apart. Specimens were tested in compression at temperatures ranging from —196 to 850"C over which range the 0.2 pet yield strength dp -creased from 160,000 p si to 35,000psi, respectively. Swaging to 40 pet reduction in area, followed by a 30-min anneal at 1000c to remove residual cold work, increased the 0.2 pet yield to 260,000 psi at -196°C, dropping to 35,000 psi at 850°C. The increase in strength was attributed to a residual cell structure. The strength of the alloy could be rationalized by the simple rule of mixtures if one assumed that additional strength is derived front a size effect characterized by is petch equation IN recent years there has been increasing interest in dispersion and second phase strengthening in materials needed for high-temperature applications. inm role of structure on the mechanical The of such alloys has been well established of such some extent accounted for theoretically. and to of how the strengthening mechanisms due to fibers and lamellae operate has been reduced to its fibers form by the fabrication of composites of strong rods unidirectionally aligned in a From work on tungsten-fiber-reinforced copper, for example, it was established that the "Rule of Mixtures" could explain the strengthening.12 " some what more sophisticated technique for introducing strong fibers into copper matrix was used by Hertzberg strong Kraft3 who unidirectionally solidified the copper-chromium eutectic. The use of unidirectionally fied eutectics has advantages in that there are no matrix-fiber wetting problems and fine fibers are automatically aligned and uniformly fiber However, one Is restricted to a specific volume fraction of the second phase. Nevertheless, even though the volume fraction is fixed, the rod or lamella thickness, , can be varied by controlling the freezing interface velocity. Alternatively, the grown material may be worked down by swaging or rolling. Embury and Fisher, " using this approach, drew down pear lite in iron and studied the mechanical properties iron and that the yield strength, oy, was properties.proportional They that d was the wire diameter. It could be inferred that was also proportional to but the work hardening had to be taken into consideration at the same time. By varying the growth rate of the cadmium-zinc lamellar eutectic, Shaw'1 showed that was proportional to without the introduction of work hardening and suggested that the lamellar interface itself contributed to the strengthening of the composite. In this investigation we have evaluated the mechanical properties of the unidirectionally solidified fec-bec eutectic Ni-Cr. This eutectic was selected because it presented the possibility was selected beca temperature, and high corrosion resistant alloy, and also represented a hard-soft phase combination with two completely different slip systems. Specimens were tested in compression and tension up to 850°C and a detailed study of the micro structure as a function of plastic strain and temperature was carried out by light and electron microscopy. It was shown that the composite strength tested in compression can be accounted for by the simple rule of mixtures if one allows for an additional term representing the effect of Intereprese EXPERIMENTAL PROCEDURE 1) Unidirectional Solidification. Fig. 1 is a schematic drawing of the apparatus used to produce 0.2 in. diam by 12 in. long alloy ingots. The crucible tube is alumina, containing the charge which has been is swaged, or machined to 0.195 in. diam. The lower end of the tube is immersed to 0 .195in in.d iam. The upper end is supported by a 10 mil nichrome wire which lowers the crucible mil nic hr the] wire at a prescribed rate. Surrounding the furnace is a graphite susceptor into which a control thermocouple is inserted. The furnace is insulated with fiberfrax and enclosed in a quartz tube. There is a sliding seal at the bottom around the crucible and one on the top so that an atmosphere may be used for the sample and suscep tor. The power for the furnace is supplied from a 10-kw, 450 kc generator. The skin depth (the skin depth at which the field falls to l/e of its value at the outer surface) for graphite (p = 10 (j-ohm-cm) is 0.1 in. at this fre-

Jan 1, 1970

By J. F. Myers, S. E. Sharp

The safety data presented in this paper are based upon replies to a Questionnaire sent out to representative mining companics. The authors feel that it is a fair cross section of the milling industry, in that the 17 companies, of the United States and Canada, reporting on 22 mills, are scattered from the Hudson Bay to the Mexican border and from coast to coast. These data concern the accident records of the various plants from 1939 to 1944, inclusive and the six years are divided into two periods. The first period (1939, 1940 and 1941) represents something of a normal operating condition. The second period (1942, 1943 and 1944) represents the period of time that was most affected by war conditions. During the second period there was a high labor turnover, inexperienced workers were numerous, women replaced men in many kinds of work, a labor shortage existed more or less throughout the industry, and supervision was pushed for peak production. All of the companies reporting compiled their accident experiences for these six years in accordance with the standards set up by the American Standards Association (New York, N. Y.), consequently the tabu lated data presented herein are comparable. The authors of this paper feel that the industry as a whole is greatly indebted to the personnel of the companies that furnished these data, which make this study possible for presentation. This survey covers a total exposure of 74,528,880 man-hours, with 105,471 man-days of lost time from 870 accidents. Safety Records In Table I, the safety record is shown of the various mills reporting. The severity rate is usually conceded to be the most vital statistical figure in safety parlance, therefore the participating companies are listed in order of their severity rate for the combined six-year period, under size of organizatiori. The table also shows the frequency rate as well as the frequency-severity ratio (F/S). As noted in Table I, most of the companies suffered an increase in both severity and frequency rates during the second period; only six of the 22 enjoyed an improvement. From correspondence with the various plants, it seems that a few had very little labor shortage or turnover, and these were not greatly affected. A few plants, anticipating the situation, strengthened their training facilities and actually were able to show a better experience during the second period. This gives great credence to the value of organized training in any safety program. The frequency-severity ratio (F/S) shown in the last column of Table I offers

Jan 1, 1947

By S. E. Sharp, J. F. Myers

The safety data presented in this paper are based upon replies to a Questionnaire sent out to representative mining companics. The authors feel that it is a fair cross section of the milling industry, in that the 17 companies, of the United States and Canada, reporting on 22 mills, are scattered from the Hudson Bay to the Mexican border and from coast to coast. These data concern the accident records of the various plants from 1939 to 1944, inclusive and the six years are divided into two periods. The first period (1939, 1940 and 1941) represents something of a normal operating condition. The second period (1942, 1943 and 1944) represents the period of time that was most affected by war conditions. During the second period there was a high labor turnover, inexperienced workers were numerous, women replaced men in many kinds of work, a labor shortage existed more or less throughout the industry, and supervision was pushed for peak production. All of the companies reporting compiled their accident experiences for these six years in accordance with the standards set up by the American Standards Association (New York, N. Y.), consequently the tabu lated data presented herein are comparable. The authors of this paper feel that the industry as a whole is greatly indebted to the personnel of the companies that furnished these data, which make this study possible for presentation. This survey covers a total exposure of 74,528,880 man-hours, with 105,471 man-days of lost time from 870 accidents. Safety Records In Table I, the safety record is shown of the various mills reporting. The severity rate is usually conceded to be the most vital statistical figure in safety parlance, therefore the participating companies are listed in order of their severity rate for the combined six-year period, under size of organizatiori. The table also shows the frequency rate as well as the frequency-severity ratio (F/S). As noted in Table I, most of the companies suffered an increase in both severity and frequency rates during the second period; only six of the 22 enjoyed an improvement. From correspondence with the various plants, it seems that a few had very little labor shortage or turnover, and these were not greatly affected. A few plants, anticipating the situation, strengthened their training facilities and actually were able to show a better experience during the second period. This gives great credence to the value of organized training in any safety program. The frequency-severity ratio (F/S) shown in the last column of Table I offers

Jan 1, 1947

By Albert Sauveur

Floris Osmond, Honorary Member of the American Institute of Mining Engineers, born in Paris, March 10, 1849, died at Saint-Leu near that city, June 18, 1912. Taken suddenly ill with congestion of the brain while on his way from Paris to his home, he reached it in time to write on the typewriter his last wishes, one of which was that no biographical notice of his life should be published. Holding Osmond's memory sacred, as those who have known him will, is it our duty to conform with his desire ? Shall no mention be made in our Transactions of the beautiful life and great achievements of one of our most honored members? Is it not, on the contrary, incumbent upon us to disregard Osmond's instruction in this matter and to place on record our admiration for the nobility of his life, for his talents and for the importance of his work, that younger men may be inspired by it with a desire to be guided by worthy motives in the path of unselfish pursuits ? I cannot feel that in following this course I am disloyal to Osmond's memory and I am strengthened in this belief by the opinion of men of high honor whom I have consulted before undertaking the writing of this obituary notice. One of them, Professor Henry M. Howe, justifies my decision better than I could do it myself when he writes : " Let us look frankly at the matter. Here we have a most extraordinary life, a life of rare beauty and power of inspiration to the rest of mankind. In my opinion we should not deprive mankind of the stimulating influence of the example of M. Osmond simply because he shrank from publicity. Our young men see every day how greed and vulgar push succeed, and with what material rewards they are crowned. They see too rarely the more valuable crown which comes to self devotion. A permanent and public recognition of the beautiful qualities of Osmond's life cannot fail to appeal to the imagination of young men and to help to deflect them toward leading a noble rather than a sordid life. Therefore I feel that the Revue de Métallurgie and other bodies owe it to the public to give prominence to his career by means of biographical notices."

Jan 1, 1914

By W. A. Klikoff, I. Fatt

The concept of fractional wet wattability is examined. Fractional water wettability of a reservoir rock is defined as the fraction of the internal surface urea that is in contact with water. Capillary pressure and relalive permeability of unconsolidated sand are shown to be functions of fractional wettability. INTRODUCTION The petroleum industry has long recognized that wettability of reservoir rock has an important effect on multiphase flow of oil, water and gas through reservoirs. As early as 1928 the American Petroleum Institute sponsored a study of wettability as part of API Project 27 at the U. of Michigan.' Despite 30 years of research, there is still little exact knowledge of the wettability of reservoir rocks. There are two parts to the wettability problem. After agreeing to a uniform nomenclature in regard to wettability,' the first question to be answered is, "What is the in situ wettability of a given reservoir rock?" If this can he answered the next question is, "What part does wettability play in determining the characteristics of multiphase fluid flow through the rock?" This paper represents an oblique attack on the problem of wettability. No attempt is made here to answer the basic question of wettability in situ. instead the consequences of the concept of fractional wettability are examined. Multiphase flow in sandpacks is shown to he highly influenced by fractional wettability. Jennings' has given 3 definition of wettability and the other terms used in discussing wettability. These terms must be applied to the physical situation existing In reservoir rock. A survey of the pertinent literature from 1928 to 1956 indicates that the concept of a contact angle was applied to reservoir rock in the same way it would be applied to a flat, homogeneous surface. Attempts were made to state quantitatively the wettability of a reservoir rock in terms of a contact angle which was presumably constant at all points on the very rough and heterogeneous interior surface of a porous rock. Calhoun, et al,3-6 prepared synthetic consolidated and un-consolidated porous media in which they claimed there was a known uniform contact angle. They then showed the effects on the capillary pressure and relative permeability characteristics of varying this angle. The API Project 47 at the U. of Texas' and others' have made extensive studies of an indirect approach to the contact angle through the use of heat of wetting data. Even if successful. however, this approach also states the wettability of porous rock in terms of a contact angle which is uniform over the entirc surface. If the angle varies from one part to another on the internal surface, there is no way of determining from the measurements the area distribution of contact angles. In 1956 Brown and Fatt5 suggested that the concept of a contact angle, as applied to reservoir rock, be abandoned. This suggestion was made because it is known that the internal surface of most reservoir rocks is composed of many different minerals, cach with a different surface chemistry and a different capacity to adsorh surface active materials from reservoir fluids. Furthermore, the operation of a contact angle in determining the form of a fluid-fluid interface is difficult to picture in the very complex geometry of a pore. Brown and Fatt proposed that the wettability of reservoir rock be stated in terms of the fractional internal surface area that is in contact with water or oil. All surfaces on which there is water are called water-wet; surfaces on which there is oil are called oil-wet. The fractional water wettability is then stated as a number which represents the fraction of the internal surface that is in contact with water. A symmetrical statement can be made for the fractional oil wettability. The concept of a fractional wettability as previously stated has in its favor the recognition of the heterogeneous mineral composition of most reservoir rocks. Another point in its favor is that fractional wettability can be measured quantitatively with relative ease. Hol-brook and Bernard10 se a simple dye adsorption test to obtain fractional wettability of reservoir rocks. Amott11 uses a combination of imbibition and displacement to arrive at a wettability index of reservoir rocks which seems related to fractional wettability in the range 0.25 to 0.75 fractional water wettability. Jennings" has shown the changes in relative permeability that take place when a porous material is changed from unity to zero fractional water wettability. He also shows that reservoir rocks in their natural state, but at room temperature and atmospheric pressure, have relative permeability characteristics which would indi-

By H. A. Tobelmann

age Introduction ............................. 22 Crushing............................... 25 Leaching............................... 28 .Reduction.............................. 47 Electrolytic Deposition..............a.......... 51 Discard for Purification of Electrolyte.................. 60 Recovery of Copper from Discard Solution .............. 62 Resolution of Cement Copper...................... 64 Summary............................... 64 Appendix............................... 66 Discussion............................... 69 Introduction The location, mode of occurrence of ore, and preliminary tests leading to the development of the present leaching process and the building of the present plant on the property of the New Cornelia Copper Co. at Ajo, have been described in previous papers presented to the Institute and in the discussions thereof.l It is sufficient to say that these tests began early in July, 1912, and were continued to the close of January, 1916; that small tests at Douglas were followed by the construction of a 1-ton plant at the mine; and this was followed by the operation of a 40-ton plant for 11 mo. In all about 15,000 T. of ore were treated experiment-

Jan 1, 1919

By A. M. Gaudin, A. F. Taggart

Flotation of ores is a practical utilization of the energy that resides in the surfaces of solids and liquids. The best known manifestation of this energy is called surface tension; an equally important, though less apparent, phenomenon is adsorption. This paper reviews some of the recent investigations of these phenomena, and gives the results of certain experiments performed by the authors. Surface tension is a manifestation of energy having its seat at the bounding surface between the adjacent phases of a multiphase system. Thus, at the interface between a liquid and a gas, or between two immiscible liquids, or between a solid and a gas or a liquid, there are forces capable of doing work, their magnitude depending on the nature of the adjacent phases and the extent of the bounding area. These surface forces are inappreciable when the ratio of surface to volume of the adjacent phases is small, but they become powerful when this ratio becomes large, as it does when one of the phases is highly dispersed. Froth flotation, which consists in buoying solids heavier than water to the surface of water by means of gas bubbles, utilizes the force of surface tension to attach the solid particles to the gas bubbles and again to maintain the floating mass of bubbles as a more or less persistent froth at the surface of a pulp for a sufficiently long time to allow its removal. It follows from the second law of thermodynamics that the potential energy of a system in equilibrium is a minimum. Therefore a multiphase system, tending toward equilibrium, will arrange itself in such a way that the total energy of the interfaces will be the least possible. This end can be accomplished in two ways: by a change in shape that will reduce the interfacial area; by a change in the nature of the surface layer in

Jan 1, 1923

By A. F. Taggart, A. M. Gaudin

Flotation of ores is a practical utilization of the energy that resides in the surfaces of solids and liquids. The best known manifestation of this energy is called surface tension; an equally important, though less apparent, phenomenon is adsorption. This paper reviews some of the recent investigations of these phenomena, and gives the results of certain experiments performed by the authors. Surface tension is a manifestation of energy having its seat at the bounding surface between the adjacent phases of a multiphase system. Thus, at the interface between a liquid and a gas, or between two immiscible liquids, or between a solid and a gas or a liquid, there are forces capable of doing work, their magnitude depending on the nature of the adjacent phases and the extent of the bounding area. These surface forces are inappreciable when the ratio of surface to volume of the adjacent phases is small, but they become powerful when this ratio becomes large, as it does when one of the phases is highly dispersed. Froth flotation, which consists in buoying solids heavier than water to the surface of water by means of gas bubbles, utilizes the force of surface tension to attach the solid particles to the gas bubbles and again to maintain the floating mass of bubbles as a more or less persistent froth at the surface of a pulp for a sufficiently long time to allow its removal. It follows from the second law of thermodynamics that the potential energy of a system in equilibrium is a minimum. Therefore a multiphase system, tending toward equilibrium, will arrange itself in such a way that the total energy of the interfaces will be the least possible. This end can be accomplished in two ways: by a change in shape that will reduce the interfacial area; by a change in the nature of the surface layer in

Jan 1, 1923

By L. E. Mannion

Sodium carbonate (soda ash) is one of two principal commercial alkalis. Its principal competitor is sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines and solid salts provided impure soda for early glassmaking. Until the 19th century, soda ash (as well as potash) was recovered mainly by leaching wood or other plant ashes. In 18th-century Europe, for example, leaching seaweed ash with hot water produced a brown laundry lye. One of the better grades of this material was a Spanish product, barilla, which analyzed 24 to 30% Na2CO3 (Hou, 1942). The modern chemical industry was born in 1691 with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. English industry used this process extensively in the 17th and 18th centuries. The next major advance was in 1863, when Ernst Solvay devised the ammonia-soda, or Solvay process. The first of many Solvay plants was built in 1874. These supplanted the LeBlanc method and dominated worldwide soda ash production until 1974, when mined sodium carbonate became predominant. Although considerably less important until recently, natural sodium carbonate deposits historically have supported small soda ash operations throughout the world. Shortages during World War II stimulated production of "natural" soda ash from such deposits, particularly at Searles Lake, CA and Lake Magadi, Kenya. More spectacularly, increased production from the vast trona deposits in Wyoming has virtually supplanted the Solvay process in the US. Principal producers of natural soda ash as well as the character of the source deposits are listed in Table 1. [ ]

Jan 1, 1983

By H. I. Aaronson, H. A. Domian, G. M. Pound

Zener's two-parameter theory of the y a reaction in Fe-X alloys is extended to encornpass austenite-stabilizing as well as fewite-stabilizing elements, and is then cottzbitzed with statistical thermodynamic theories of Fe-C alloys to permit development of a ther-modynamic description of the proeutectoid fewite reaction in Fe-C-X alloys. Equilibrium tielines are calculated for tile a + y rep'on from experimental data and frort extrapolations of the y/y +a equilibrium surface. Sectzovs of the y/y + 0 surface are calculaled for the tzetastable sstuation LYL u-kich alloyrtg eleitzents do not partition betzseen azrstenite andfer-rite. The finding that the metastable y/a + y curves Lie close to their equilibriuwz counterparts when X = Si, .Vo, Co, Al, and Cu but well below them when X = A/ln or Ari pr-elides a thermodunamic explanation for the expcri1?7e?ztally obserted absence of partition during the proeutec toid ferrite reartlon in the fortner alloys and for the occurrence of partition at hzgher ternperatures in the latter alloys. Cotarison ofno- patitzoa free-energy changes and y/y i a curr,es in Fe-C-X alloys with the equilibrium 11al1es of these quantities in Fe-C alloys furnishes additional qualitative insight into the irqluence of allojling elements upon the kinetics of the proeutectoicl ferrite reaction. THE introduction of a substitutional alloying element, X, appreciably complicates calculation of the thermodynamics of the formation of proeutectoid ferrite from austenite. As noted in the preceding paper,' the positional entropy of the interstitial species is the principal component of the free energy of an interstitial solid solution with which theory has so far been able to deal. One would expect, however, that other components of the free energy of this type of solid solution may be significantly altered by the addition of a substitutional alloying element. Even if the assumptions are made, by analogy to the case of Fe-C alloys,' that changes in the positional entropy of carbon represent a significant part of the thermodynamic effects of an alloying element, and that the remaining effects can be taken into account by fitting the equations developed on this basis to experimental data on Fe-C-X phase diagrams or on the activities of carbon in alloyed austenite and ferrite, the experimental information available on either of these quantities is not yet sufficiently accurate or extensive, respectively, to make such an approach useful. An attempt made by Zener on the former basis to explain the effects of alloying elements on the thermodynamics of Fe-C alloys in terms of a temperature-independent "free-energy change" (actually enthalpy hane') required to transfer 1 mole of an alloying element from austenite to ferrite, in which the "free-energy change" was determined by fitting the theoretical relationships developed to Fe-C-X phase diagrams, thus proved inadequate in part because of deficiencies in the available ternary-phase-diagram data.= Other difficulties of a more fundamental nature, however, also indicated the desirability of a different approach to the problem.3y4y6 zener6 subsequently proposed that the free-energy change associated with y — a transformation in pure iron can be decomposed into magnetic and nonmagnetic components. Alloying elements were assumed to affect those components separately. One parameter was used to describe the quantitative effect exerted on each component. These parameters were evaluated from Ms (martensite-start) temperature data and from other experimental information usually either readily available or measurable with acceptable accuracy. Zener applied this treatment only to the calculation of Fe-X phase diagrams in which X is a ferrite-stabilizing element. In the present study, this treatment is extended to include austenite-stabilizing elements, and then combined with treatments previously considered for Fe-C alloys1 to permit calculation of the thermodynamic quantities of interest in the austenite - proeutectoid ferrite transformation in Fe-C-X alloys, where a number of representative, and commonly used alloying elements are chosen for X, including Si, Mn, Co, Mo, Al, Cr, and Cu. The results are used to explain important features of the partition of alloying elements between austenite and proeutectoid ferrite, as reported in a companion paper7 on the basis of electron-probe analysis, and to provide some additional understanding of the influence of alloying elements upon the kinetics of nucleation and growth of proeutectoid ferrite. Portions of this treatment6 have been clarified in the course of a review by Kaufman and Cohen.3 The consolidated summary of these developments with which this section is begun provides a basis for further clarification of the treatment, from which extension to include austenite- as well as ferrite-stabilizing elements is a natural consequence. The division of the free-energy change associated with the 7 - a transformation in pure iron, into two independent components is formally stated as:

Jan 1, 1967

By Reinhardt Thiessen

UNDER sulfur in coal, is usually understood that form of sulfur which is combined with iron and known as pyrite. It occurs in the form of halls, lenses, nodules, continuous layers, thin sheets, or flakes, both in horizontal planes and vertical cleavage fissures. But pyrites also occur as very fine microscopic particles, or nodules, disseminated through the compact coal. This form has had but very little consideration. Finally, there is sulfur in coal in an amicroscopic form (not visible with an ordinary microscope), probably combined with the organic matter that exists -in tile coal. This form has had considerable attention from a scientific standpoint, but has probably not been recognized enough on the economic side. One or the other, or both, of these two latter forms may comprise the larger part of the sulfur content of coal, especially after it has been washed or otherwise prepared for use.

Jan 9, 1919

By B. R. Queneau

[ ] B. R. QUENEAU-One of the difficulties in metallurgy has always been a lack of precision in measurement, and I think the authors are to be congratulated on developing a method which will give us an accurate and dependable quantitative estimate of the amount of retained austenite. O. ZMESKAL*-As Chairman Queneau said, this is indeed an ingenious and needed determination. We have seen figures presented of 1/2 pct retained austenite determined, and I would like to ask the authors the lower limits of this method. How far down do they feel they can go in improving the technique still more?

Jan 1, 1948

By A. R. Kaufman, P. Gordon

THE large-scale manufacture and use of uranium in conjunction with the atomic energy development during the war led to a need for knowing the equilibrium diagrams of uranium with various other metals. The alloys of uranium with aluminum and with iron were among the first that were studied for this purpose. Much of the work was done in the manner of a survey since it was necessary to determine the important features of the phase diagrams rather than to obtain completely detailed results. For this reason no attempt was made to locate exactly such features as liquidus lines, solid solubility limits and compound and eutectic compositions. It is believed, however, that there are no great inaccuracies in the diagrams reported here and that no important points were overlooked. Earlier work on alloys of uranium with aluminum and iron is almost nonexistent and in each case is considered to have been of little value by M. Hansen. It is interesting to note, however, that the compound UAl3 was first reported in 1902 by L. Guillet. Experimental Procedure Materials: The uranium used for making most of the aluminum alloys was obtained from material prepared by Metal Hydrides, Inc., and melted in vacuum at M.I.T. Because of the lack of an adequate supply of metal, it was necessary to use material from several different batches and hence it is impossible to state an exact analysis. However, a few results indicated about 0.01 to 0.03 pct iron and probably about 0.03 to 0.05 pct carbon. Toward the end of the work a small amount of metal was obtained from Brown University and from Iowa State College and this was used in determining the transformations in pure metal and in some dilute alloys. All of the aluminum used in this investigation came from a supply of high purity metal (greater than 99.9 pct aluminum) which was obtained through the courtesy of Dr. Mehl of the Carnegie Institute of Technology. The uranium used for making the alloys with iron was produced by the bomb reduction process which has been described by J. Chipman.² This metal, after vacuum melting, contained about 99.9 pct uranium by weight with carbon and iron as the chief impurities. Electrolytic iron containing about 0.012 pct carbon, 0.020 pct nickel and 0.009 pct copper was used in making the melts. Melting Equipment: The melting of the alloys went through a stage of development which culminated in the use of beryllia or beryllia-lined crucibles and in the use of high frequency heating in either vacuum or in an atmosphere of argon. It was found that uranium at a few hundred degrees above its melting point would pick up aluminum and to a lesser extent silicon from an alundum thimble while aluminum above 1000°C would extract silicon from the impure alundum. No reaction of either metal with beryllia was noted at temperatures as high as 1800°C. The distillation of aluminum from the aluminum-rich alloys was quite troublesome at temperatures above about 1300°C and was only partially avoided by the use of argon instead of vacuum. Melting in resistance furnaces,

Jan 1, 1951

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is necessary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important components of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transformation are dealt with in a highly detailed and descriptive manner in the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilibrium conditions of thermal treatment. The Guillet1 diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts. At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. [ ] Reference may be made at this point to the efforts of Marshy to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encoun-

Jan 1, 1942

By Henry Lloyd Smyth

In 1891-92 1 was entrusted with the geological survey of part of the large area lying between the Marquette and Menominee iron-ranges in the Upper Peninsula of Michigan, and extending from the Republic trough on the north, through portions of the valleys of the Michigamme and Fence rivers, to and including the intermediate Felch mountain range on the south. Until a few years back the larger part of this area has been very difficult of access, and much of it is difficult still. The rock-surface is for the most part covered with swamp, forest and glacial deposits of various kinds, and therefore has not invited geological study. For these reasons the district, as a whole, with the exception of the Felch mountain range, remained almost unknown from a geological standpoint until our work in 1892. Our main object was to map the pre-Cambrian rocks, particularly the iron-bearing formations of Algonkian or Huronian age, and to obtain as much information as possible with reference to their sequence and structure, In carrying out this purpose, the use of simple magnetic instruments was found to be of the greatest assistance, and indeed indispensable. In this paper the results of our experience in tracing magnetic rocks by means of the disturbances produced in these instruments, have been brought together in systematic form, with such references to the particular area as are necessary in order to illustrate general principles, with the hope that they will prove useful to other workers in the same region, or in other regions where similar conditions may be encountered. The writer was efficiently aided in the field-work by Messrs. Samuel Sanford and Charlea N. Fairchild for nearly the whole period, and E. B. Mathews and H. F. Phillips for part of it,

Jan 1, 1897

By B. M. Larsen, T. E. Brower

A perspective is presented of the steel plant sulphur distribution and elimination problem from coal to liquid steel ready for teeming, giving distributions of sulphur over a range of coke sulphur content, and some methods of sulphur control, in the blast furnace, external desulphuriza-tion between blast furnace and open hearth, distribution between fuel, slag, and metal, and methods and limitations of control of sulphur in the open hearth furnace. AS a part of the 1951 AIME symposium on sulphur in steelmaking, it was thought that a discussion of the distribution of sulphur throughout the whole series of operations, from coal and ore to finished steel ingots, might have some value in giving a perspective on the whole problem. The following discussion is an attempt to present such an overall picture. The order is that of the actual plant operations, beginning with a very brief consideration of the coking process. Sulphur in Coal and Coke Since by far the largest source of sulphur entering the steelmaking cycle is in the coal used to make coke for the blast furnace, it would seem reasonable to eliminate some of it, either from the coal, or the coke, or during the coking process. This has appeared impracticable up to the present, at least, for two main reasons: the low activity of the organic sulphur in either coal or coke, and because of price limitations involved in treating a low cost material such as coke. A variable portion, usually M or less, of the sulphur is present in coal in the form of pyrites or similar compounds, and a large part of this sulphur may be removed in the coal washery. Most of the sulphur, however, is normally present as "organic" sulphur, intimately associated with the coal structure. Its distribution prevents any separation by mechanical means. Its low activity makes improbable ' any rapid chemical removal, although hydrogen will remove sulphur from both coal and coke. Thus, prolonged recirculation of coke oven gas in the coking process would tend to leave a smaller percentage of the total sulphur in the coke residue. Table I shows a typical distribution of sulphur from coal into products in the coking process. As the sulphur in the coal increases, the sulphur in the coke tends to increase in about the same proportion. Sulphur in the Blast Furnace The best picture of the situation in the blast furnace is provided by a sulphur balance of raw materials entering, and of products leaving, the furnace. The difficulties in accurate weighing and sampling of the variable solid materials entering this process, and the number of hours required for the raw materials to descend through the furnace under variable operating conditions, make it difficult to obtain an accurate balance. However, balances made over periods of weeks or months tend to average out some of these uncertainties. Table I1 presents three typical sulphur balances similar to a number that the writers have calculated. In most of these the slag volume calculated from the sulphur balance is, in some instances more, and in other instances less, than the value corresponding to the best input and output balances of the other slag constituents (lime, silica, alumina, etc.). Probably the greatest source of error in these calculations is the sulphur content of the slag. Despite some possible inaccuracies the balances of Table II show rather definitely the following points: 1—That 87 to 95 pct of the total sulphur input is in the coke and 95 to 97 pct of the total sulphur output is in the slag. Also, that if any sulphur leaves the furnace with the gas it is relatively small, amounting to a possible 1 pct or less. 2—At the lower sulphur coke level of 0.86 pct the total amount of sulphur charged is 15 Ib of sulphur per ton iron increasing to 26 lb per ton at the higher sulphur, intimately associated with the coal struc-rare burdens containing sulphur-rich ores will the total sulphur burden fail to be nearly proportional to the content in the coke used. 3—The 7 to 9 pct of the total sulphur input from the limestone of furnaces B and C is due to the relatively high sulphur content of the stone, 0.226 and 0.265 pct, respectively. In the case of furnace A, the sulphur content of the limestone was only 0.06 pct which resulted in only 3 pct of the total sulphur input coming from this source. It is rather interesting to compare the sulphur balances of a typical ferromanganese furnace with

Jan 1, 1952

By Charles H. Foreman, James F. McCarthy

The orebodies of the Hecla mine are from 3 to 40 ft. wide, dip not less than 70°, and in most cases are nearly vertical. The Hecla and Intermediate orebodies are generally associated with a lamprophyric dike, usually about 2 ft. wide, but which attains a maximum width of 7 ft. The ore appears on either or both sides of the dike. The country rock is Burke quartzite with no definite walls and a tendency for nearly horizontal, but irregular, quartz stringers to run from the lode into the walls. This latter condition prevails almost entirely in the hanging wall, causing a natural tendency for portions of the wall to "offset" and resulting in an extremely heavy side pressure. The fact that there are no definite walls causes a great variation in the width of the stopes, as stringers will run into the walls for irregular distances. The ore occurs as galena in varying widths and grades. It is often necessary to mine a face having a " horse"' of waste between two stringers of ore. This block of waste might be 6 or 7 ft. wide but with the Hecla method it is necessary to mine the entire face. In this case an effort is made only to shatter the waste, allowing for easy sorting underground. The Hecla mine requires a flexible system allowing for the extraction of ore from varying widths, with the necessity of close filling to give the needed protection from side weight. About 15' per cent. of the material broken in the face is sorted as waste, either at the face of stope, or in the sorting plant. Shafts, Drifts and Crosscuts The outside dimensions of the shaft are 19 ft. 4 in. by 7 ft. 2 in. The shaft consists of three working compartments, two for the hoisting of ore and one for auxiliary work. The working compartments are 5 ft. 2 in. by 4 ft. 4 in. inside measurement. The rest of the shaft is used for pump column, electric cables, and ladderway. (See Fig. 6 for framing of timbers.) The shaft is about 700 It. from the orebody for topographical reasons. Solid formation was not reached in shaft for 80 ft. Timbers in this section became alternately wet and dry on account of seasonal changes

Jan 1, 1925

By Gerald F. G. Sherman

The ore deposits of the Warren district, in which the mines of the Copper Queen Consolidated Mining Co. are situated, have been described in a number of technical publications, and will not be discussed here in detail. Certain of their characteristics, however, control methods of underground transportation and hoisting of ore. In the Copper Queen mine, the majority of the ore has occurred in a zone encircling the west boundary of the porphyry intrusion of Sacramento Hill. It has a width varying from 800 to 1,200 ft., and a thickness of about 400 ft. It reaches the surface in the older part of the mine to the northwest, but dips to the southeast, where it is reached at 1,400 ft. below the Czar collar, in its farthest extension at present developed on Copper Queen ground. There is one major extension from the northwest end of the zone toward the west along the Czar fault, and others of minor importance. Individual orebodies are scattercd through the zone in an eccentric manner, only matched by their own irregularities of form and size. Their most gencral characteristics are the softness of the ore and their grcat horizontal rather than vertical extent. It has been estimated that the average vertical thickness of ore in the Czar and Lowell divisions is between 30 and 35 ft. It is calculated by assuming it to be uniformly distributed over its horizontally projected area. In this zone, and for some distance above it, the ground has been subjected to intense alteration and intense but irregular oxidation. It has resulted in an enormous quantity of earthy or clayey material, which may be either ore or waste, which when wet is both heavy and tenacious. Below alteration, the ground is fairly hard, and the limestones contain primary ores differing from those heretofore considered typical of the camp, and which have not yet been thoroughly exploited. The mine production has been drawn from many orebodies spread over a great area.l A diagram map (Fig. I), of haulage drifts and loading stations, illustrates the situation in 1914.

Jan 1, 1916

By Emmanuel P. Papadakis

Ultrasonic velocity measurements have been made to study the preferred orientation in cube-textured copper. Methods applicable to thin specimens were employed since the specimens were necessarily of sheet material. The measured velocities in various directions in the sheet differed from the corresponding values in single-crystal copper by 1 to 6 pet. The distribution of the deviations indicated that the align-ment of the (001) planes with the rolling plane was better than the alignment of the [100]and [010] directions with the rolling and transverse directions. Ultrasonic pole figures (velocity us orientation) are shown to be useful in the study of preferred orientation. THIS paper describes one set of experiments in a continuing study of preferred orientation in worked metals. This study has been undertaken to investigate the fundamental properties of metals when used as propagation media for ultrasonic waves. Many such materials are of current or potential use in ultrasonic delay lines. Fundamental studies on ultrasonic propagation parameters such as velocity, attenuation, and diffraction (beam spreading) are of importance in the design of delay lines, in the development of nondestructive testing methods, and in the study of materials themselves. Preferred orientation in worked poly-crystalline metals influences all three above-mentioned parameters, and hence is of particular importance. When polycrystalline metals are subjected to mechanical working, they develop textures dependent upon their crystal structure and the symmetry of the working operation.' The texture consists in the alignment of the crystallographic axes of the grains in preferred directions with respect to the symmetry axes of the working operation. Since the grains are elastically anisotropic, the elastic moduli of worked metals are anisotropic. Hence the velocities of elastic waves in worked metals depend on the directions of propagation and polarization. The worked metal may be thought of as taking on the elastic symmetry of a single crystal: so it possesses the same number of independent elastic moduli as the crystal class it simulates. In general, a worked metal does not adopt the crystalline symmetry of its own grains. For instance, most rolled sheet becomes effectively orthorhombic while all bar stock and wire develop hexagonal symmetry. However, certain metals with cubic crystal structure develop a cube texture upon rolling and annealing.= Nearly perfect alignment of [100]-type directions with the rolling direction, transverse direction, and rolling-plane norma1 can be achieved in certain fcc metals and alloys. These cube-textured rolled metals provide an excellent opportunity to test preferred orientation by means of elastic waves, since a worked metal with 100 pct cube texture would have elastic moduli identical to the moduli of its constituent metal. It is the purpose of this paper to present the results of an investigation upon cube-textured copper. Ultrasonic waves were used. The methods of measurement and the experimental results on the effective moduli will be given. The ultrasonic measurements will be shown to complement X-ray pole figures for the determination of preferred orientation in worked metals. EXPERIMENT To study cube - textured material, it was necessary to use thin-sheet material since a severe reduction in gage (95 to 99 pct) is necessary to produce cube texture. Special ultrasonic methods were needed to investigate the thin material at megacycle frequencies. A) Materials. The cube-textured material tested was a copper alloy containing 1 pct Zn. Specimens already measured for Young's modulus4 by Alers were kindly supplied by him. The specimens were slabs 3.00 by 0.25 in. cut from sheet 0.047 in. thick. The orientations of the long axes of the specimens with respect to the rolling direction were taken in 15-deg steps from 0 to 90 deg. B) Measurements. Two distinct experiments were performed to measure the phase velocity in these specimens. One measured the shear wave velocity for propagation in the 0.25-in. direction and polarization in the 3.00-in. direction. The other measured the velocity of both shear and longitudinal waves propagating in the thickness direction in the sheet. 1) Plate-Mode Measurements. The velocity of the zeroth-order shear mode5 was measured in the 0.25-in. direction in each strip. The specimens were ground thinner over half their length to assure that the first-order shear mode would be cut off below 6 Mc per sec, leaving the zeroth-order nondispersive shear mode as the only propagating mode. Piezoelectric ceramic transducers of 5 Mc per sec resonant frequency poled in their long direction were solder-bonded to the edges of the thin part of the slabs as in Fig. 1 after these edges had been made flat and parallel by fine grinding. These transducers produced waves polarized in the 3.00-in. direction and propa-

Jan 1, 1967

By Samuel B. Christy

The present paper is a continuation of a study of the reductionworks of New Almaden, the first part of which was published under the title " Quicksilver-Reduction at New Almaden," in the Transactions of this Society, vol. xiii., p. 547.* Frequent reference will be made to some of the data there given. The following is an outline of the contents of this paper: I. Condensing appliances used at New Almaden: a. Brick condensers, b. Iron condensers—flues and " water-backs," c. Glass and wood condensers, d. Friction-coudensers—filters and revolving screens, e. Flues, towers, and chimneys. II. Analysis of condensing-systems. III. Temperature of condeusers. IV. Product of condensers. V. Treatment of soot. VI. Losses of treatment: a. Nature of losses, b. Composition, weight, and volume of dry gases, c. Volume of wet gases, d. Specific weight of quicksilver vapor, e. Vapor-loss at various temperatures. VII. Comparison with New Almaden practice. VIII. Comparison with results at Idria, Austria. IX. Comparison with results at Almaden, Spain. X. Future improvements in quicksilver-condensation. I. Condensing Appliances. The complete condensation of mercurial fumes in a large way presents numerous practical difficulties, familiar to all who have had to retort amalgams. In condensing the quicksilver-fumes discharged

Jan 1, 1886