Search Documents

By P. S. Kotval, O. H. Nestor

Stacking fault energy measurements of nickel-base alloys have been mainly confined to binary and ternary systems. In this paper, the stacking fault energy has been measured by the rolling texture method in a series of ten alloys which comprise successive additions of Cr, Mo, Fe, and C to pure nickel, eventually resulting in an alloy of the composition of Hastelloy alloy X. The alloys studied here are single-phase, solid solutions with the exception of two alloys in which some undissolved particles of "primary" carbide have been retained. It is found that successive additions of chromium, molybdenum, and iron all lower the stacking fault energy, with iron having only a minor effect. The stacking fault energy is found to increase when carbon is added in solid solution. The results from the rolling texture measurements are correlated with thin foil observations of dislocation substructures in these alloys. In a recent paper' it was pointed out that the dislocation substructure of various superalloy matrices could be classified into three broad categories based on 'high', 'medium', and 'low' stacking fault energy. It has also been demonstrated2 that the dislocation substructure in each of these categories has a well defined role in the nucleation of strengthening precipitates which is different from the role played by the dislocation substructure in other categories. Thus, it becomes desirable to understand the influence of various solute elements on the stacking fault energy and hence on the dislocation substructure of the matrix, before any further development of superalloys by mi-crostructural predesign can be undertaken. Recently, Beeston and France have studied the influence of increasing solute additions on the stacking fault energy of a series of binary nickel-base alloys relevant to the Nimonic series using the rolling texture method, and have then estimated the effect of a given alloy addition in five commercial Nimonic alloys. However, comparison with stacking fault energy data from other investigations''5 suggests that the influence of a given solute element in a nickel-base binary system is not necessarily the same in a ternary or more complex superalloy system. Accordingly, the present work was undertaken to study the effect of successive addition of solute elements to pure nickel, the final composition being the nominal composition of Hastelloy X. The rolling texture method of stacking fault energy measurement was used since it can be used for the whole range of stacking fault energy values and does not have the disadvantage of, say, the Node method which is only applicable to low values of stacking fault energy. In addition, the rolling texture method provides a means of determining the stacking fault energy which is statistically more significant than that provided by other methods. EXPERIMENTAL TECHNIQUES Button heats of alloys of the compositions shown in Table I were prepared. Each button was remelted not less than four times. After a slight deformation (approximately 5 pct) all alloys were homogenized at 2200°F except alloys, H . I, and J. Alloys H and I were solution heat treated at 2150°F and alloy J at 2282OF. The buttons were cold worked by rolling, using "end-to-end" passes and intermediate anneals at the homogenization temperatures mentioned above. After each annealing treatment the samples were rapidly water quenched to avoid any precipitation. In alloys F and I, however, a few particles of "primary" carbides were retained even after the homogenization treatments at the temperatures mentioned above. Part of the solution heat treated material was cold worked to 0.04-in.-thick sheet and the penultimate reduction was -50 pct of deformation as recommended by Dillamore et al. All annealing was carried out in vacuo within sealed quartz capsules. Some of the material from each alloy was rolled down further to 0.004 in. strip for thin foil transmission electron microscopy specimens. Specimens of this strip were annealed at the homogenization temperature for 1 hr and then strained 7 pct by rolling at room temperature. Thin foils were prepared from the strip specimens by the 'window" technique using an Ethanol-Perchloric acid electrolyte at 32°F and a voltage of 22 v. Stainless steel cathodes were employed. All transmission electron microscopy was performed in a JEM-7 electron microscope using an accelerating voltage of 100 kv. Specimens from the 0.04 in. sheet which had been rolled -60 pct in the final pass were electropolished to remove the surface layers to a depth of approximately 0.002 in. Rolling texture pole figures for all the alloys were determined using a Schulz ring and nickel filtered CuKa radiation at 50 kv and 20 ma. The texture parameter Io/(lo + I,,) (where Io is the

Jan 1, 1970

By I. H. Silberberg, R. L. Reed, O. K. Kimbler

interfacial films have frequently been observed at interfaces between certain crude oils and water. Several investigators have postulated that the presence of these films should influence the efficiency of oil recovery in water drive or waterflood operations. They may also influence the stability of emulsions which are sometimes a problem in petroleum production, and may be a factor in the fonation of paraffin deposits in oil well tubing and flow lines. This paper presents a technique with which a modified Langmuir film balance may be used to study the compressibility and collapse pressure of these natural interfacial films. Experimental data are presented for several nude oil-water systems. Data developed are used to infer the phase state of the film as a function of such variables as rate of reduction of interfacial area, ionic composition of the subtrate and pH of the subtrate. A film of known physical characteristics is shown to have a sinnificant effect on oil recovery from an unconsolidated sand pack. Possible applications of these results to petroleum production are discussed. INTRODUCTION The use of water to displace petroleum from reservoir rocks is of major importance both as a primary and a secondary recovery process. As water invades the rock, oil is completely displaced from some pores and left as a discontinuous phase in other pores. The manner in which water moves from pore to pore is strongly influenced by capillary forces. In view of the complexity of reservoir fluid systems, there can be little doubt that complicated interactions take place at both the liquid-solid and oil-water interfaces. One of the more interesting, and least understood, of the phenomena which take place at the oil-water interface is the formation of interfacial films. These films are believed to result from the adsorption of high molecular weight polar molecules at the interface.l.2 Presence of such molecules may cause a striking alteration in interfacial tension. When the oil-water interfacial area of certain crudes is rapidly reduced, a thin region (film) about the interface assumes the appearance of a solid membrane, and striations, wrinkles and gross distortions may occur. If such a film is solid, it should greatly alter the interfacial tension normally assumed to exist between the oil and water phases. If the membrane is continuous, a solid phase would separate the oil and water. Interfacial films between crude oil and water were observed in 1949 by Bartell and Niederhausers who commented upon the apparent rigidity of the films and their possible importance in the petroleum industry. Morrell and Egloff4 had earlier attributed the extreme stability of emulsions of sea water in fuel oil to very stable asphaltic films. Numerous investigators have observed rigid films in the course of crude oil-water interfacial tension determinations by the pendent drop method. Several investigators5,6,2 have separated inter-facially active materials from crudes and attempted to characterize them chemically. Reisberg and Doscher,2 using Ventura crude, showed the interfacial tension against water (as measured by the pendent drop method) to be affected by aging, contraction and expansion of the interface, and the pH of the water. These investigators attributed the adhesion of oil to a water-wetted surface and the distortions of flow paths in glass capillaries to the presence of rigid films. Dodd7 has studied the interfacial viscosity of adsorbed films and found them to be non-Newtonian in behavior. Craighead and Harvey8 reported a series of displacements in tubes packed with 60 mesh glass beads. They interpreted the results as indicating an effect of stearic acid films on waterflood recovery and imply that natural films may produce similar results.

Jan 1, 1967

By John Wulff, J. H. Hollomon

THE opinion has been widely held that the corrosion of alpha brass occurs by the selective solution of zinc. As late as 1939, Fink1 and Evans2 suggested that in the initial stage of the corrosion the selective solution of zinc produces copper-rich areas, which subsequently act as cathodes that facilitate the deposition of copper. Previously Abrams3 had shown that most of the copper found on corroded brass was redeposited and not residual, although he did not consider the nature of the initiation of the corrosion process. Enough data exist to indicate that any metal surface is sufliciently heterogeneous to provide the anodes and cathodes necessary for the initiation of corrosion .4,5 Thus, for alpha brass we need postulate not an initial selective solution of zinc, but only the existence of local differences in electrochemical potential. The heterogeneity responsible for potential differences may arise from oxide and other films as well as from alloy concentration gradients. Even though selective corrosion may be possible in some alloy systems, previous data on alpha brass as well as the experimental work reported in this paper do not require this supposition. Bengough and May,6 in a discussion of Abrams' paper, first suggested the addition of small amounts of arsenic (0.03 per cent) to alpha brass to prevent the redeposition of copper (dezincification). This suggestion was later substantiated by Nixon.7 In their studies of the inhibiting influence of arsenic, Evans and Fink were led to the selective-solution hypothesis in order to explain the initial corrosion of such alloys. "I hey believed that an arsenic film covered anode areas and prevented the formation of copper-rich spots capable of acting as cathodes for the deposition of copper. They (lid not consider, however, the mechanism by which the arsenical film was formed. Bengough and May,8 in another publication, suggested that the commonly found gray or black arsenical film may act to: (1) carry oxygen to the brass surface, (2) increase the discharge potential of copper on brass, (3) precipitate cuprous chloride from colloidal suspension in chloride solutions. Masing9 assumed that the film found upon arsenical brass was metallic arsenic. His measurements of hydrogen overvoltage of bulk arsenic led hint to believe that the inhibition of dezincification occurs because the overvoltage of a brass surface is lowered by the arsenic film. He reasoned that this film would permit the more rapid reduction of hydrogen at the cathode, which would prevent the redeposition of copper. In a recent paper,10 we have pointed out that the film formed (luring the corrosion of arsenical brass and copper in stagnant solutions is essentially arsenious oxide (AS208)

Jan 1, 1942

By R. J. Mechin

Top-slicing was introduced in the Pachuca district in 1917 by T. C. Baker, at that time mine superintendent of the Santa Gertmdis mine. There then existed 1200 ft. below the surface, lying between the fourteenth and eighteenth levels (a vertical distance of 354.2 ft.) a block of ore having a length of 295 ft. and an average width of 82 ft. and dipping at an angle of 65°. This block lay in the hanging wall of the vein and consisted of highly altered and fractured andesite, cut through with mineralized quartz stringers. On the foot-wall side, 26 ft. of old filling, left by former operators, was of payable grade. Stoping therein was first undertaken by the square-set filling system, but because of the extremely heavy hanging wall and loose dry filling in the foot wall, all square setting had to be accompanied by spiling, which made the operation exceedingly slow and costly. A system of mining was sought that would eliminate the difficulties inherent to the square-set system in heavy ground and that at the same time would effect the desired economies in mining. After several years, top-slicing has met all the conditions most satisfactorily, so that when similar conditions presented themselves in El Bordo mine, this method was adopted with necessary modifications. El Bordo mine is operated by the Santa Gertrudis company, and is situated about two miles north of Pachuca. Because of the diversity of the orebodies, a number of different mining methods are in use, among them top-slicing. Description of Block of Ore Former operators, when mining the original vein, left in the foot wall ore of too low grade to be profitable at the time; also, considerabe low-grade material was sorted out and stored as filling in the stopes. Some pillars were left in place, either for support or because they were not payable. All this has formed a body of ore that can now be exploited

Jan 1, 1925

By W. T. Lankford, Low J. R., Gensamer M.

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By Low J. R., Gensamer M., W. T. Lankford

The problem of sheet metal formability is one which has received a vast amount of attention during recent years. In spite of the great amount of study and experimental work which has been devoted to this problem, many of its fundamental aspects are still not well understood. No generally satisfactory test has been developed which is capable of providing a reasonably adequate evaluation of sheet metal formability, particularly in borderline cases. Anomalies persistently arise in which a lot of supposedly satisfactory material exhibits excessive breakage when formed. This lack of suitable technological tests greatly hinders the design of new parts and the substitution of new materials in parts of existing design, frequently necessitating considerable costly trial and error experimentation on an actual production basis. When, at the beginning of World War 11, it became apparent that mass production methods of forming would bc required in the aircraft industry if the large numbers of military aircraft needed were to be supplied, renewed attention was focussed on the problem of sheet metal formability. It was widely recognized that the formability requirements placed on sheet metals had been steadily increasing in severity through the years, especially as greater and greater emphasis was placed on streamlined designs with the resultant freer application of doubly curved surfaces. The recent advent of several new high strength aluminum alloys of more limited formability than some of the older alloys also served to emphasize the need for new approaches to the problem. It seemed evident that progress in the technology of sheet metal forming would depend to a great extent on the development of more reliable criteria for the evaluation of formability. Although the problem is admittedly very complex, the most logical approach appeared to be through studies of the fundamental material properties of sheet metals, especially under complex stress conditions simulating those prevailing in actual forming operations. Most previous investigations have failed to make full use of existing knowledge of fundamental material properties, and in many instances have attempted correlations with properties which are now recognized as being ambiguous in nature. This investigation was undertaken, therefore, with the aim of developing methods for the study of the flow and fracture of sheet meta1s under combined stresses, and of making use of such methods as might be developed in

Jan 1, 1947

By R. D. Pehlke, J. V. Gluck

A study was made of' the effects of up to five additional solutes on the thermodynamic activity of zinc in dilute solution with molten bismuth in the range 450" to 650°C. The experimental measurements were made in a multielectrode galvanic cell apparatus employing fused LiCl-KCl as the electrolyte. The solute additions included indium, lead, tin, cadmium, copper, silver, antimony, or gold. A range of positice and negative interactiotls with zinc was covered. The experinzer~tal observations were cowlpared with the activity coefficients calculated usitlg either Wagner's first-order Taylor series rnodel or a proposed second-order solution itrteraction model. hi general, the truncated first-order Taylor series proposed by Wagner gaue good results for "dilute" solutions (XBi > 0.90) contaitzing up to six solutes. The second-order model, which includes a second-order cross-interaction term, produced a slight improvement in predictions for solutions with XZn = 0.015 and a significant improvement for solutions with XZn = 0.050 hear the limit of Henry's law region). Seveval of the quaternary solutions studied contained a total solute content of 0.215 mole fraction, and fairly good success was achieved in predicting the activity coefficient 01- zinc. ThE study of thermodynamic interactions between dilute solutes in liquid metallic solutions has occasioned much recent interest. It is useful to recall in this respect that Wagner's well-known expression for the activity coefficient' is a practical application of the problem of representing a given function, i .e., In ?, by means of a sequence of polynomials. No specific physical model of a solution is involved in its use. As suggested by Wagner, a Taylor Series is used to expand In ? about a point of infinite dilution with respect to all solutes. The partial differential coefficients of the series have been termed "interaction parameters". Various authors'-6 have proposed formalisms for parameters, the definitions being designed to meet some specific experimental or physical condition. A usual assumption is that terms above first-order in the Taylor Series may be neglected. In that case, the logarithm of the activity coefficient is expressed as a linear function of solute concentrations. The resulting expression is presumed valid for any number of additional solutes as long as the solution can be regarded as "dilute". This assumption can be termed "the hypothesis of additivity". However, experimental tests of that hypothesis for quaternary or higher-order solutions have been extremely limited. Primarily such tests have been confined to studies of effects of added metallic elements on either the activity of carbon or the solubility of gases in liquid iron.7-13 The only known previous study of an all-metal system is the limited work of Okajima and pehlke14 on the effects of multiple solute additions on the activity of cadmium in liquid lead. The present investigation is a portion of the work to determine the effects of various solute additions on the activity of zinc in dilute solution with molten bismuth in the range 450" to 650C It was shown for such ternary solutions that second-order Taylor Series terms could be evaluated at the same time as first-order terms, with no additional experimentation required. A second-order solution model was described which, under certain conditions, is a rigorous representation of solute activity in a ternary solution. (In the sense employed in this paper, the term "model", as distinguished from "equation", is taken to mean an empirical correlation or formalism, but not a hypothetical physical system per se.) Presumably such a model could be extended to produce a better representation of In ? in solutions of even higher order. The feasibility of a generalized Taylor Series approach to solution interactions and inclusion of second-order terms also has been discussed recently by Lupis and Elliott in independent work concurrent with the present investigation. In addition, they discussed empirical means of estimating certain second -order coefficients.17 The utility of such solution models rests on the ability of a truncated series to represent adequately the experimental facts in multicomponent solutions. Questions that arise include: Do the second-order terms really make a significant contribution? How far away from "dilute" solution may such models be applied? Are the types and varieties of the additional solutes important? among others. In order to provide some answers to these questions, an experimental study was made of the effects of two or more additional solutes on the activity of zinc in dilute solution with molten bismuth. Comparisons were then made with calculated activity coefficients obtained using the previously determined ternary interaction parameters. INTERACTION MODELS As an example of the approach to defining activities in multicomponent solutions, consider the Taylor Series expansion for a quaternary system, i.e., three dilute solutes. Writing terms through second order, the result is:''

Jan 1, 1968

By R. Schempp

DURING the past few years, general interest in the steel-producing and steel-consuming industries has been centered on the so-called "inherent characteristics" of steels. While often vaguely described, these char-acteristics are known to influence the response to heat-treatment and the hardening characteristics of the material. Although most of the recent papers and discussions have associated the "inherent characteristics" with the austenitic grain size and empha-sized the importance of it, comparatively little is known of the variables that may affect the size of the austenite grain. The work to be described in this paper was carried out during the course of a study on the inherent characteristics of tool steel containing one per cent cart on. The discrepancies encountered in the determination and classification of the austenitic grain size led to in investigation of some of the variants influencing the austenitic grain size as determined by standard methods.

Jan 1, 1937

By Ben L. Seegmiller

Introduction The profitability of an open pit operation depends to a large extent on the use of the steepest pit slopes possible, provided they do not fail during the life of the mine Optimum pit slopes can be designed by using rock mechanics technology. Such technology includes gathering and analyzing pertinent data prior to pit design, rigorous application of rock mechanics principles during the design process, remedial actions to improve slope stability, and monitoring slopes during the life of the mine. Ignoring rock mechanics technology in pit design may place the entire mining enter- prise in jeopardy Disruption of mining operations and safety hazards caused by slope instability can be severe. A classic case in point is the major slope failure (Seegmiller, 1972) that occurred at a southwestern US copper mining operation in 1970-1971 Minor slope stability problems initially amounted to no more than a nuisance, but in time, the unstable zones became larger, causing greater disruption of production and threatening safety Mining at or near the slide toe had continued throughout the period of slope failure, aggravating the already unstable condition The original plan for this pit called for mining the overall pit slope to 37.5" Mine operators were forced to lessen the back- slope angle in the hope that the failing rock mass would stabilize. However, stabilization did not take place, and when mining in the area of failure was completed, the overall slope had been reduced to approximately 27" Mining had been successful in removing only a small portion of the ore body at a high stripping ratio.

Jan 1, 1979

By Wilbur C. Helt, Joseph J. Yancik

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production ; and to produce electricity. Because it is our nation's most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health and environmental goals are rapidly emerging. These technologies will allow coal's use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals. MARKETS FOR COAL: PAST AND FUTURE A simplified diagram of the marketing network for coal is shown in Fig. 1. As shown in this figure, coal is transported to its traditional

Jan 1, 1981

By E. P. Barrett

THE high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,1 in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. SHAPE AND SIZE OF CENTRIFUGAL LIQUID CRUCIBLES When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape f a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 ½ in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections f the cylinders, shows the effect f speed f rotation of the containers upon the shape f the inner surface f the rotating liquid crucibles.

Jan 1, 1938

By A. G. Worthing

Black: Bodies.-In the ordinary conception, a black object is an opaque object that reflects but little of the light that is incident on it. This means naturally that such an object is a good absorber of luminous radiation. The black body; which is so closely connected with high-temperature measurements, represents the limit in blackness of all black objects. It is a body that not only absorbs all visible radiations but also all other radiations in the infra-red and the ultra-violet regions of the spectrum which are incident on it. No substance is known that is completely black; platinum black, one of the nearest if not the nearest representative of the ideal, reflects 1 per cent. or so of ordinary visible radiation. The closest approach to the ideal is a small opening in the wall of a relatively large opaque cavity. Any radiation incident on this black body will be almost completely absorbed if the relative dimensions are properly chosen no matter what the material may be. The great difference between the blackness of such a cavity and of lampblack, for instance, will be apparent to one who makes the simple test. Non-black Bodies.-The field of non-black bodies covers all real bodies. Their characteristics are extremely varied. So far as absorption of radiation-is concerned, these bodies range practically from the almost completely black, platinum-black, and lampblack, which absorb all but a fractional part of 1 per cent. or so of the incident radiation, by an infinite variety of steps to freshly polished silver, which ordinarily absorbs only a few per cent. The exact percentage absorbed depends not only on the nature of the incident radiation, but also on the temperature of the body, the condition of its surface, the angle of incidence, the nature of the surrounding medium, and on certain other less important conditions. As consequences of these varied characteristics, we have not only the differences of color of ordinary objects, but also the changes of color that any one object undergoes on heating or when lighted front various directions. This complexity of the phenomena, in a way, is responsible for the meagerness of knowledge, regarding materials at elevated temperatures. Measurement of High Temperatures.-Excepting in cases where the thermocouple or the gas thermometer are applicable, in which case the temperatures obtained are true temperatures regardless of-the material" studied, high, temperatures are almost always, if not always, determined from measurements of radiation. In fact, determinations of temperature from this latter point of view are often so much more convenient than the thermocouple and especially the gas-thermometer determinations that, in the region where all of these types of measurements may be made, the radiation measurements are often preferred. This is true even though the temperatures usually thus directly determined are not the actual temperatures, a consequence of the sources of the radiation being non-black bodies; in other words, a consequence of being concerned with iron, or glass, or tungsten instead of small openings leading to relatively large-cavities uniformly heated. Coordination of Experimental Results.-In order that data on iron, glass, tungsten, or other non-black bodies obtained in one laboratory, may be, correlated with similar data obtained elsewhere, temperatures must be expressed on a common scale. The true temperature scale is the natural scale for this purpose it is ordinarily the scale to which all other temperatures can be most directly reduced. When the measurements depend on the radiation, a knowledge of emissive powers repre-

Jan 9, 1919

By Charles S. Barrett

THIS paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstructures. About 12m exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,1 and a number of these have been selected to illustrate the results obtained. Prints are also included showing the common types of falsities-to borrow a term from the biological field, the "artifacts." In brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. n addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains. Since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. SPECIMEN PREPARATION AND PHOTOGRAPHS Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for repeated polishing and etching (each successive polish becoming less severe and each etch lighter), since the final etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and IC, the replicas used were of silica, deposited up0n polystyrene and floated from the polystyrene in ethyl bromide according to polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1943

By A. I. Krynitzky, Henry S. Rawdon

The most commonly used material for terminals in spark plugs is commercial nickel wire, because of its relatively high temperature of melting, excellent heat conductivity, and slow rate at which the metal is oxidized, even upon continued heating at high temperatures. The grade commonly used for this purpose averages 97 per cent. nickel, the remainder being manganese, cobalt, iron, copper, with traces of other impurities always found in commercial nickel. A peculiar and interesting type of deterioration that occurs in these nickel terminals during the service life of the spark plug was recently brought to the attention of the Bureau of Standards. Commercial spark plugs vary greatly in their size and shape and the terminals differ considerably as to their relative size, shape, number, and arrangement with respect to one another. Although this defect was studied in detail in only one form of spark plug, the deterioration is a characteristic of the material, i.e., of nickel wire, rather than of the particular type of spark plug in which it was noted and studied. The mechanical features of the plugs, however, have a considerable bearing on the time required for the deterioration to become serious. The results of this study of the deterioration of nickel terminals in service should be of value to the makers of all types of spark plugs in which the terminals are made of this metal. CharacteR of Deterioration of WIres During Service Macroscopic Appearance and Properties of Changed Wire.—The nickel terminals in which the deterioration was studied were taken from spark plugs having a central terminal with the ground or side terminals attached firmly at both ends to the shell of the plug. In some of the plugs, two side terminals were used, one on each side of the central one. Although both terminals were found to have deteriorated to some extent, the attack of the central one was quite negligible compared to that of the side ones. These latter wires had developed, in service, transverse cracks that, in many cases, were as sharp and definite as a knife-cut. After a separation occurred, the breach widened by loss of material from the

Jan 1, 1921

By J. Washburn, R. Drouard, E. R. Parker

Temperature dependence of the rate of recovery in zinc single crystals after a simple shear deformation at low temperature was investigated. Some tentative suggestions regarding the annealed and strain-hardened states of a crystal are discussed. RECOVERY may be defined as the gradual return of the mechanical and physical properties of strain-hardened metal to those characteristic of the annealed material; an increase in temperature increases the rate of recovery. The annealing process in strain-hardened polycrystalline metals is complicated by the inhomogeneity of strain which always exists in aggregates. Polygonization in bent regions of the crystals and growth of new almost strain-free grains starting at points of severe local distortion1-:' make it almost impossible to isolate and study the recovery process. Homogeneously strained single crystals, however, do not polygonize or re-crystallize and hence they can be used advantageously to study recovery. In such crystals strain hardening is completely removed by recovery alone. Since recovery is a process whereby certain lattice disturbances introduced by plastic flow are gradually reduced, a knowledge of the rate and temperature dependence of this process for various conditions of prestrain might be helpful in formulating a model of the strain-hardened state. For simplicity it seemed desirable to limit the type of prestrain to the simplest obtainable, i.e., simple shear strain. In the experiments to be described, recovery was studied by observing changes in the stress-strain curve of prestrained zinc single crystals held for various times at temperatures above that employed for straining. Single crystals were grown from the melt by a modified Bridgeman technique from Horse Head Special zinc 99.99 pct pure, and from spectrographically pure zinc 99.999 pct pure. They were grown as 1 in. diameter spheres and acid-machined' to the final specimen contour. The test section was a cylinder about 1/8 in. high and 3/4 in. in diameter. The conical sections adjacent to the test section were cemented into the grips so the load could be transmitted to the crystal as uniformly as possible. The specimens were oriented so that in testing the maximum shear stress was applied along one of the slip directions, [2110], in the (0001) plane. Details of the production and testing of such specimens have been presented.' Each test was carried out according to the following schedule: 1—The crystal was strained at — 50°C until it reached a maximum shear stress, ,,,. The strain rate was approximately 5 pct per min in all cases. 2—After straining, the crystal was unloaded before the temperature was changed. Unloading required about 3 min. 3—The temperature of the specimen was then increased from — 50°C to the temperature, T, of recovery. This change in temperature was completed in a time of less than 2 min. The specimen remained at temperature, T, for a time, t, which differed for the various specimens. 4—Thereafter the temperature was again reduced to — 50 °C in approximately 3 min. 5—While at —50°C, the stress-strain curve after recovery was obtained. 6—The specimen was then unloaded and annealed for 1 hr at 375 °C in a helium atmosphere to bring about complete recovery. Cooling to room temperature after anneal required 90 min. 7—The same crystal could be re-used for another test because the plastic properties after annealing closely duplicated those of the original crystal. The specimen was immersed during the test in a bath of methyl alcohol which, through a system of tubes, could be pumped through either of two heat exchangers to regulate the temperature; this was accomplished by circulating the liquid through coils immersed in a bath of acetone and dry ice for cooling or in a bath of warm water for heating. Test temperatures were thus maintained constant within ±1°C. The — 50°C temperature was low enough so that no measurable recovery occurred during unloading and reloading. The stress-strain curve continued after recovery along a path below, but approximately parallel to, the path of a curve obtained in an uninterrupted test. Fig. 1 shows some of the results from a specimen of 99.999 pct Zn. The amount of downward displacement of the curve due to recovery was a

Jan 1, 1954

SOUTHERN CALIFORNIA LOCAL .SECTION Executive Committee SEELEY W. MUDD, Chairman C. COLCOCK JONES, Vice-Chairman. FREDERICK J. H. MERRILL, Secretary-Treasurer, 631 Higgins Bldg., Los Angeles, Cal. RALPH ARNOLD A. B. CARPENTER The Southern California Section, held a dinner and meeting at. the Sierra; Madre Club, Los Angeles, on Friday evening, Sept. 28, 1915, at which 21 members and guests-were present. The Vice-Chairman, C. Colcock Jones; presided, in the absence of the Chairman. The amendment' to the By-Laws providing for the increase of the Executive Committee from five to seven members, having been formally presented at the annual meeting of June 18, 1915, and duly announced for consideration at this meeting, was voted on and unanimously adopted. Prof. Robert H. Richards of the Massachusetts Institute of Technology; made a short address on the subject of ore concentration. The paper on the Geology and Ore Deposits of Mojave, County, Arizona, prepared by F. C. Shrader, was presented to the meeting by the Secretary and was discussed by Allen Burris and Dr. L. D. Godshall. F. J. H. MERRILL, Secretary.

Jan 11, 1915

By G. M. Schwartz, J. N. Gundersen

John W. Gruner (Professor Emeritus, College of Science, Literature, and the Arts, Dept. of Geology, University of Minnesota, Minneapolis) — It is surprising that two men as well acquainted with the taconite rocks of the Mesabi District as Drs. J. N. Gundersen and G. M. Schwartz should have concluded that the taconite of the Eastern Mesabi before the intrusion of the Duluth gabbro consisted largely of quartz and magnetite. These minerals were "locally reconstituted" into "a wide variety of silicate mineral assemblages" by the gabbro. It is well known, of course, that the silicate mineralogy of the Eastern Mesabi ('about 14 miles in length) is quite different from that of the Main Mesabi which is over 60 miles long. The change from one to the other is abrupt and cannot be attributed to any other cause than the thermal effects of the gabbro. Are we to assume or believe that the taconite of the Eastern Mesabi was radically different from that of the Main range before the gabbro metamorphosed it?

Jan 1, 1962

Bethlehem Steel Co. has just brought an all-new iron ore mine into production at Marmora, Canada, about 120 miles east of Toronto. High grade pellets produced at the mine from open-pit magnetite ore travel 64 miles by rail to the port at Picton, then go by Lake boat to help supply Bethlehem's Lackawanna, N. Y., plant. At full production about half a million tons of pellets a year will be shipped, and mining will be at a scale of more than a million tons per year of ore. Aeromagnetic surveys carried out in 1949 by the Ontario Dept. of Mines and the Canadian Geological Survey revealed an anomaly that interested Bethlehem geologists. By 1951 the company had put down some 40 diamond drillholes ranging from 460 to 1800 ft to block out the magnetite replacement deposit which lies in pre-Cambrian limestone below about 130 ft of Paleozoic limestone. The orebody, roughly 2100 ft long and up to 400 ft wide, averages about 37 pct iron, too low for direct shipment. Not only construction of concentrating and pelletizing facilities, but 20 million tons of stripping lay ahead before production could start

Jul 1, 1955

CHUQUICAMATA, as the Chile Copper Company's mine is known, has the largest developed deposit of copper ore in the world. Indeed, it is improbable that its equal will ever be found. The Union Miniére du Haut Katanga, operating in the Belgian Congo, may some day surpass Chuquicamata in the total amount of copper produced; or one of the companies developing the rich copper region of Northern Rhodesia may ultimately outdo it. But in each instance, the ore will come from a group of mines separated by 80 miles or more; whereas the deposit at Chuquicamata is one vast integral mass containing as a minimum probably 1,000,000,000 tons of ore, averaging better than 8.5 per cent copper, and as a maximum-well, most any reasonable figure might err on the low side. Utah Copper approaches Chuquicamata more nearly than any other in tonnage of exploitable ore; but Utah's ore is less than half as rich. The figure for the aggregate copper content of the reasonably assured ore at Chuquicamata is breath-taking at 50,000,000,000 pounds. Other distinctions has Chuquicamata: It was the first of the Porphyry Coppers to use leaching as the method of treating the ore; its plant cost for producing is lower than that of any of the others, only Braden and Utah being close rivals; and it was worked for its copper long before any of the others. According to an authentic article published in Ingeniería Internacional (May, v 1982) the Incas smelted copper ores from Chuquicamata prior to 1536. Diego de ALnagro, to whom Charles V, King of Spain, generously allotted a one-fourth portion of South America lying south of Cuzco, the Inca metropolis, made an expedition into Chile in 1534. Better known to history, perhaps, is Pizarro, who was awarded the area immediately north, and who proceeded

Jan 1, 1933

By George A. Roberts

The development of an alloy system, high-speed steel, is used as an example of the progress of physical metallurgy. Tracing the history of men and their thoughts as they studied and invented and modified these materials, the story of high-speed steel since the 1890's is seen to be a long, slow, but steady progression of achievements. Today's multiplicity of high-speed steels are the result. Data are presented on quantitative metallography of carbides in high-speed steel with high vanadium content using the QTM instrument. Grindability as well as mechanical properties are related to the content of excess MC and M6C carbides in a series of high-speed steels and the newer matrix steels. These emphasize the present state of knowledge and show the current stages of thought that may affect the development in succeeding years. It is a great thrill for me, an ex-research metallurgist and ex-practicing metallurgical engineer, to speak to an audience currently engaged in both pursuits on the occasion of the 43rd Howe Memorial Lecture before the Iron and Steel Division of the AIME. I shall not review Henry Marion Howe's distinguished career, so adequately reviewed in Maxwell Gensamer's contribution in the 1965 AIME History of Metallurgy, except to point out that, while leading the life of an intellectual, he worked as a practicing research metallurgist and a practicing metallurgical engineer for significant periods of time and contributed greatly in both areas. For those of you who believe, as I do, that in the intellectual activity of metallurgy we are blessed with an intimate mixture of science and engineering (see Mehl's 1960 Howe Lecture), we might recall that Howe, while pursuing a life of writing and teaching in later years, served as the first Chairman of the Division of Engineering of the National Academy of Sciences. That metallurgists were called upon then to lead an engineering recognition movement is perhaps related to the strong part played by the AIME and its members in the recent establishment of a National Academy of Engineering and to the fact that a metallurgist is its head, 47 years after Howe served. I stress these engineering aspects for I wish to talk about a metallurgical engineering subject today. Alloy systems, physical metallurgy, and steel blended with an historical perspective and a report on new techniques to improve the old will, I trust, be of sufficient interest to bring these lectures back to the physical-metallurgy banner from which they have departed for 4 years. Those process metallurgists, open-hearth fiends, and physical chemists among you will just have to be patient. The development of an alloy system is the engineering application of scientific thought and fact. There are many interesting alloy systems, developed to a high degree of technology and sophistication over the past 40 to 70 years. These systems are bound together and related by a similar set of characteristics. For example, stainless steels are a system in which the members are related by a high chromium content which gives a corrosion-resistant characteristic. A subfamily in this system would be austenitic steels

Jan 1, 1967