Search Documents

By R. C. Craze

This paper discusses the characteristics of the velocity logs now available to the petroleum industry, and some of their advantages and limitations. The velocity log was designed as an aid to the geophysicist to determine velocity layering in the earth and to provide fast, accurate and economical vertical travel time data. After a number of logs had been made, studies were carried out on their use ia correlating strata in adjacent wells. It was found that adjacent strata usually show sufficient velocity contrast to make it possible to correlate these from well to well, even in areas where electric or radioactive logs fail.' In addition, velocity logs have been useful in the determination of porosity and thickness of reservoir rock.' These uses for velocity logs require an understanding of the characteristics of the log in response to the changes in velocity and in borehole conditions encountered normally in logging. GENERAL DISCUSSION OF INSTRUMENTATION The measurement made in velocity logging is more accurately described as a measurement of time rather than velocity. Ideally the log is obtained by measuring the length of time required for compressional sound waves to travel through a fixed distance in the formation. In practice, the time measurement may be made accurately but the distance through which the waves have traveled may vary slightly. Changes in borehole diameter are responsible largely for the difficulty in maintaining a fixed distance, especially if the diameter variations are so abrupt and frequent that the borehole instrument cannot follow contours of the hole. Several service companies have velocity logging equipment available or under development which have different transmitters, receivers, and measuring systems. While these differences are important, there are actually only two systems in use at the present time (Fig. I)."' The first system initiates a pulse at a trans-mitter and detects it at a single receiver. The transmitter and receiver are separated by a fixed distance, called the spacing. The time measured is that between the initiation of the pulse and the first arrival of acoustical energy at the receiver. The second system uses two receivers and a transmitter. The receivers are separated by a fixed distance and the time between arrivals of energy at the two receivers is measured. Here, the spacing is the distance between receivers. The two systems have much in common for it is possible to record both logs simultaneously. Usually the transmitter is an electro-mechanical transducer which produces discrete

By P. Shahinian, H. H. Smith, M. R. Achter

Crack growth rates are measured at elevated temperature in a resonant fatigue machine from vibration frequency decreases calibrated in terms of crack depth. Crack growth rates in Type 316 stainless steel at 500º and 800°C show a sharp increase with oxygen pressure in an intermediate pressure range and little or no change at high and low pressures. At 500°c, I torr of oxygen reduces the fatigue life by almost a factor of 100 in comparison to that in vacuum and raises the growth rate of shallow cracks by the same At At 800°C the effects are smaller. Changes in slope in the crack growth rate curves are discussed in terms of a model in which rates of surface production and of surface coverage by gas are compared. The use of a calculation method in which the surface exposure time is equal to X/v, where x is the interatomic spacing and v is the growth rate, makes it possible to obtain order of magnitude agreement at 500°C between the observed pressure and the predicted pressure at these slope changes. At 800°C oxidation becomes a .factor and the data cannot be treated by simple adsorption theory. THE decrease in the fatigue life of metals as a function of gas pressure usually follows a stepped curve with virtually all of the decrease concentrated in a sharp drop in a transition zone at intermediate pressures and little or no change at low and high ranges. A number of models, differing in the details of the mechanism, have been offered to explain the shape of the curve. Measurements of crack growth in aluminum as a function of gas pressure by Bradshaw and Wheeler' and Hordon2 demonstrated opportunities for quantitative comparison to evaluate the proposed models. Since comparable data were lacking at high temperatures, in the present work rates of crack propagation were measured in Type 316 stainless steel at 500" and 800°C as a function of oxygen pressure. Choice of this material was dictated by two considerations; it is stiff enough at these elevated temperatures to resonate with the regenerative drive on our fatigue machine and it is known to display a large effect of environment. A new method of calculation is described to predict the gas pressure at the critical point. EXPERIMENTAL PROCEDURE Because of the difficulty of measuring crack depths directly at high temperatures, an indirect method was developed based on the decrease in the resonant frequency with the growth of a crack. A reversed bending, constant amplitude fatigue machine, described previously,3 vibrates a specimen at its resonant frequency, automatically records any changes in it and shuts itself off after it has reached a preset value of frequency decrease. The record of frequency change is used to determine the rate of crack growth. Sheet type specimens of Type 316 stainless steel, Fig. 1, incorporated a sharp, shallow notch to localize the formation of a single crack. After machining, they were annealed in a vacuum of l0-6 torr either at 1066" (lot A) or 871°C (lot B) and then electropolished in an acetic-chromic acid solution. Bending strains were measured at 500" and 800°C by an optical technique4 and reported as total strain without correction for the notch. At 500°C, the 0.141 pct strain was 0.085 pct elastic and the remainder plastic. At 800°C the 0.062 pct strain was all elastic. To convert frequency decrease to crack length, calibration curves were obtained by interrupting the vibration at stated intervals of frequency decrease. The crack depth was measured microscopically at a magnification of X400 and reported as the average of the measurement on each edge. Some specimens were sectioned for crack measurement while others were returned to the machine and fatigued further. There was good agreement between the two methods. Before beginning the vibration, the vacuum chamber was first evacuated cold to 1 x 1O-6 torr, then heated to the operating temperature and held there until the pressure was again reduced to 1 x10-6 torr at which time oxygen was introduced to the desired pressure. In this investigation the vibration frequency was nominally 10 cps and a decrease of 0.6 cps was taken as the failure point. The choice of the frequency decrease to represent failure has no appreciable effect on the fatigue life because the crack is growing very fast at this point.

Jan 1, 1970

By J. F. Abel

It can be concluded that rock mechanics instrumentation, geologic mapping, and operations research in combination will produce an accurate estimate of tunnel support requirements for establishing a steel-set load prediction model. This estimate can be used to increase safety and to reduce tunneling costs. Unnecessary supports can be eliminated; overloaded or insufficient supports can be replaced on a more scientific basis than previously possible. Only a limited number of measurements are required to develop a steel set load prediction model. The results of this study can be applied generally; but, every tunnel must be considered as a separate problem. The construction and geologic variables which were found to be significant in the prediction of rock loads in this tunnel were: steel section modulus, set blocking points, percentage of alteration, relative degree of faulting, relative water condition, distance to the nearest fault, and average joint spacing. INTRODUCTION A combined engineering geology and rock mechanics program was performed throughout the Straight Creek tunnel pilot bore in Colorado in order to develop a technique for estimation of steel tunnel support loads. The technique involves the construction of a statistical model from measured steel set loads, geologic and construction factors. The aim of the investigation was to produce a set of charts, based on these factors, which could be used by a trained man equipped with a hand lens and measuring tape, to specify a safe and economical steel size and set spacing. In order to be of practical value the measured parameters had to be rapidly measurable and capable of quantification. It was apparent from the beginning that quantitative values for many of the geologic factors would have to be arbitrary. It was impossible to ascertain in advance which of the readily determi-nable geologic and construction factors significantly affect steel set loading. As the investigation progressed the number of observations was systematically reduced in order to determine the minimum amount of data which would be necessary for a significant mathematical model. This paper presents an analysis of all the variables measured at each instrumented steel set. The statistical significance of the measured variables was determined. On the basis of this determination, a mathematical model was constructed and charts were prepared to select and space the steel tunnel supports at any given point in the tunnel. Once the effect of geologic and construction factors on set loading is sufficiently established, it is possible to exert close control over the selection of steel tunnel support size and spacing. The magnitude of this rock mechanics program can be appreciated when it is known that there were 44 instrumentation stations for which steel set loads were measured. For each of these sets there were three construction variables recorded, and nine geologic parameters determined (Table I). A rough approximation of the cost for both the collection and reduction of the data would be $50,000. This is in addition to the cost of geologic mapping.

Jan 1, 1967

By R. C. Gould, A. M. Skov, L. F. Elkins

Comparison of long term decline in oil production during cyclic waterflooding or pressure pulsing of part of the Driver Unit with steady injection-imbibition flooding in the Tex Harvey area led to large expansion of flood in the Driver Unit on the steady injection basis. While the flood has been successful, the major problem has been attainment of satisfactory oil production rates in most of the wells. Large volume fracture treatments of low capacity wells were unsuccessful in achieving sustained increases in production. A two-section area in the Driver Unit has already recovered 620 bbl of oil per acre by waterflood but other areas have not performed so well. Sun Andres water containing 300 to 500 ppm H,S is sweetened to 0.5 to 1 ppm H,S by extraction with oxygen-free flue gas. This prevents contamination of gas produced in the area and apparently it has reduced corrosion in minimum investment, thin-wall, cement-lined water dktribution systems. Cement-lined tubing in injection wells has mitigated corrosion as effectively as thick polyvinyl chloride films have, and at less cost. Introduction As reported in the literature the Spraberry field of West Texas has presented unusual problems for both primary production and waterflood ing. Earlier information from the Spraberry Driver Unit included conception and evaluation of cyclic waterflooding or pressure pulsing in a nine-section pilot test as an aid to extraction of oil from the tight matrix rock and as a boost to normal capillary imbibition forces An additional 5 years' operation in that area, and performance of expanded steady injection water-flood, now covering a total of 68 sq miles, are reported herein. In addition, since the Driver Unit is one of the largest waterfloods in areal extent in the U. S., many operating experiences are presented for the benefit of engineers concerned with operation of other Spraberry floods or with other waterfloods where this reservoir technology and/or water handling technology may be adaptable in part. These include: (1) attempts to improve producing well capacity through large volume fracture treatments, (2) long-term performance of water treating plants utilizing oxygen-free flue gas to extract H,S from sour San Andres water, (3) performance of thin-wall cement-lined pipe in water distribution systems including comparison between those sections carrying raw San Andres water and those carrying treated water, and (4) comparison of performance of various lining materials and subsurface equipment in water supply and water injection wells. These experiences are reported without regard to whether results are good, bad or indifferent. Since the operations reported are limited to the techniques, materials, and equipment actually used in the Driver Unit, no comparison is possible with results of other approaches used in other Spraberry floods or in waterfloods generally under different conditions. However, an attempt is made to quantify these experiences as much as possible in the space available to permit other engineers to select those parts applicable to eheir problems. Background The Spraberry, discovered in Feb., 1949, is a 1,000-ft section of sandstones, shales and limestones with two main oil productive members—a 10- to 15-ft sand near the top and a 10- to 15-ft sand near the base, having permeabilities of 1 md or less and porosities of 8 to 15 percent. Extensive interconnected vertical fractures permitted recovery of oil on 160-acre spacing from this fractional-millidarcy sandstone, but they made capillary end effects dominant. Primary recovery by solution gas drive is less than 10 percent of oil in place, with most wells declining to oil production of a few barrels per day when reservoir pressures are still in the range of 400 to 1,000 psi. Partial closing of the fractures with declining reservoir pressure is believed to be the cause of such low production rates at these relatively high reservoir pressures. In 1952 Brownscombe and Dyes proposed that displacement of oil by capillary imbibition of water from the fractures into the matrix rock might significantly increase oil recovery from the Spraberry, overcoming otherwise serious channelling of water through the fractures." A pilot test conducted by the Atlantic Refining Co. during 1952 through 1955 indicated technical feasibility of the process; but low oil production rates averaging I5 to 20 bbl/well/D failed to create significant interest in large-scale waterflooding at that time." Humble Oil & Refining Co. conducted a highly successful 80-acre pilot test during 1955 through 1958 with

Jan 1, 1969

By C. J. Haigh

Stockpiled and currently produced zinc plant residues containing zinc ferrite are to be treated at a rate of 350 tonne per day in a plant that is being constructed at the Risdon works of the Electrolytic Zinc Company of Australasia Limited (E.Z.). Start-up of the plant is scheduled for December, 1970. The residue is to be treated by a hydrometallurgical process that was developed by E.Z. in Australia, by Det Norske Zinkkompani in Norway, and by Compagnie Royale Asturienne des Mines (Asturiana de Zinc) in Spain. The process, as it is to be used at Risdon, is simple, consisting essentially of two stages : 1. A leaching stage at atmospheric pressure in which the zinc ferrite contained in zinc plant residue is dissolved in spent electrolyte, fortified with make up sulphuric acid, at a temperature in the range 70 to 95ºC. Undissolved solids containing lead and precious metals are separated for sale to a lead smelter. 2. An iron precipitation stage at atmospheric pressure in which ferric iron is precipitated from a slightly acidic solution at 90 to 95ºC as ammonium jarosite, a crystalline double sulphate which is relatively coarse, and is easily filtered and washed free of zinc-bearing solution. Calcine is used to neutralise the acid that is liberated during precipitation of the iron. Also included in the Risdon plant are a separate stage for oxidation of ferrous iron by injection of air, and a pre-neutralisation stage, using recycled oxidation stage pulp, to neutralise excess acidity from the leaching stage before the jarosite precipitation stage. The residue treatment plant consists of conventional equipment such as covered agitated vessels, thickeners and filters. Operation will be continuous and product solution will join the main zinc plant circuit for further purifications and electrolysis. Marketable zinc production will be increased by 70 tonne per operating day by the treatment of residue.

Jan 1, 1970

By H. W. Hockin, D. r. Brandt, R. H. Walsh, P. L. Dietz, P. R. Girardot

New Jersey, Florida, and Canadian ilmenites were reduced with hydrogen or coke under various experimental conditions and the phase changes occurring in the ilmenite upon reduction have been studied by microscopic examination of polished sections and by X-ray diffraction. The products formed were dependent upon the type of ilmenite, temperature, time and reducing agent. Of the reducing agents, hydrogen was the more effective at lower temperatures. 1 HE possible utilization of ilmenite as a source of both iron and titanium has resulted in the development of a number of methods for the separation of the iron and titanium content. Slagging processes as currently used in Canada are typical of such methods. Somewhat less attention has been given industrially to the reduction of the iron content at less than the slagging temperature. Although references maybe found to such work, in general only one type of ilmenite, either natural or synthetic, has been studied by each author. We have attempted to draw some relationship between the results of experimental reduction and the type of deposit from which the ilmenite was derived, as evidenced by phases occurring in the ores and in the reduction products. Ilmenite ores having from 27 to 61 pct titanium dioxide were included in this study and in each case reduction was carried out at such temperatures that only limited coalescence of the particulate iron product occurred within the ilmenite grains. The history of the individual ilmenite samples and the temperature of reduction were found to determine the occurrence of various phases and the mode of distribution of the iron. REVIEW OF EARLIER WORK ON REDUCTION One of the earliest references to the reduction of ilmenite at less than the slagging temperature was made in 1917.' The metallic iron produced was_____ leached out by the action of dilute sulfuric or hydrochloric acid, to leave a product high in titanium dioxide. Subsequent to this, numerous patents2-'? and other references13"21 have appeared concerning reduction of ilmenite by carbon, hydrogen, carbon monoxide, methane, coal gas, water gas, or the like in the absence of fluxing agents. Mineragraphic examinations were not reported, and in the main, the only examinations made were chemical analyses. However, in two cases3,13, titanium suboxides were reported in the products and in one case2' rutile was reported, in addition to metallic iron. Both were identified by X-ray diffraction. While reductions in the absence of fluxing agents were generally followed by either a wet or dry chemical process for removal of the metallic iron, a Canadian source17 reported removal of the metallic iron by magnetic separation. By the addition of fluxing agents during reduction, the metallic iron has been coalesced into "pearls." Each reference to such a process23-28 has shown that the coalesced iron could be removed by magnetic or gravity means after the product was crushed. In the absence of fluxes, the coalescence did not generally occur. The major part of the present study has been limited to reductions without fluxing agents in order to determine the primary reactions of naturally occurring ilmenites. Titaniferous iron ores have also been studied,29-33 17, l9 their reduction having been used as the basis of a commercial process for beneficiation of such ores in Norway29 and more recently considered in the United States34,35. The ease of reduction of titaniferous iron ores relative to that of hematite or magnetite has been referred to,33 with the conclusion that the more

Jan 1, 1961

By Lester Blackner

THE PROPERTY AND LOCATION THE Ray Consolidated Copper Co.'s mining property is located on Mineral Creek 6 miles north of Kelvin, at Ray, Pinal County, Ariz. (Fig.. 1) . The mining claims now owned by the company consist of 126 lode claims, comprising 2,144.9 acres, containing at the beginning of operations 82,904,368 tons of 2.19 per cent. copper ore. GENERAL CHARACTERISTICS OF THE OREBODY The main orebody is a disseminated deposit in schist and porphyry formed by secondary enrichment. Its existence was proved by churn drilling, and it is at present one of the largest proved copper deposits in the world. The orebody itself covers .205 acres with an average thickness of 121 ft., and occupies a definite belt which has a northwest direction. Its length is approximately 5,000 ft. The width varies, being about 2,000 ft. at the west end and 2,500 ft. at the east, narrowing down irregularly front both ends to a few feet in the center. The thickness of the body varies greatly along the line of lode, ranging from a few feet up to 470 ft. thick. The ore horizon is not constant, but varies, following in a broad sense the topography The body in general dips slightly to the northeast, and is broken up by numerous small faults and fractures. The ore-bearing formations, consisting of mineralized schist and mineralized granite porphyry, stand fairly well and offer no difficulty in mining operations.

Jan 6, 1915

By E. H. Jr. Dix

OF all the alloying elements used in commercial aluminum alloys, copper stands out as by far the most important, and it is perhaps for this reason that the constitution of the aluminum-copper system has received the attention of a number of experimenters covering a period of approximately 20 years. It would be expected that during this time the equilibrium relations had been thoroughly and exactly worked out. In a general way this is true, but there is a surprising lack of agreement in the details of the high aluminum end of the diagram, particularly in regard to the solid solubility of copper in aluminum, which has been given variously as 2 per cent. to 5 per cent. at the eutectic temperature. The importance of this is much greater than might at first appear to one unfamiliar with modern commercial aluminum alloys. This is true because, with one exception, the susceptibility of the strong alloys to heat treatment depends, in part at least, upon the solid solubility relations of copper in aluminum. In 1919, Merica, Waltenberg, and Freeman1 published the first detailed information on these solubility relations. They found that the solubility of copper decreases with falling temperature from about 4 per cent. at 5.25° C. to about 1 per cent. at 300° C. and is apparently still diminishing at lower temperatures. In 1921 there was published a brief account of the results obtained in the National Physical Laboratory, Teddington, England.2 This laboratory, however, reported that 5 per cent. of copper is soluble in aluminum at 540° C., and that this amount decreases to about 3 per cent. at 20° C.

Jan 2, 1926

By A. Faison Dixon

In India the production of mica, which in other countries is of very minor importance, is one of the staple, long established industries, and ranks high in the statistics of mineral products. Nearly two-thirds of the mica of commerce comes from India. The Indians have used mica for glazing and decorative purposes through many centuries. About 14,000 men are employed in and about the mines, and the indigenous and primitive mode of mining is still followed; but, by reason of the exhaustion of the surface supply hitherto won without intelligence or capital, it will not be many years before the present interesting and casual methods will be replaced by a less archaic and more profitable system. India on the whole has little mineral wealth, but the unique resources of its mica-fields, cheap labor, and favorable natural conditions render it unlikely that any other country can ever more than temporarily contest her leadership in the production of this one minor but essential mineral. Mica plays a small but indispensable rôle in a variety of fields of dissimilar application. Its use and value depend upon characteristics which different kinds of mica have in varying degrees, each kind being adapted to its own special purpose. Its well-known characteristics of transparency, flexibility, elasticity, toughness, high dialectric strength, perfect flatness, ease of splitting into thin films, ability to stand high heat and sudden changes in temperature, give it value in many industries. No other substance, natural or artificial, has the same combination of qualities. The oldest use of mica is in glazing. By reason of the improvements in annealing glass, this is not now of great importance, but mica is still employed for the covers of ikon images in Russian churches, the windows of anthracite stoves, compass

Jan 1, 1914

By Nicholas J. Grant, A. W. Mullendore

Measurements of grain boundary sliding were made on polycrystal and bicrystal tensile creep specimens of Al-2 pct Mg at 500oand 700oF. Grain and pain boundary orientation factors were studied with respect to their effect on the magnitude and direction of grain boundary sliding. It was concluded that a large part of the observed sliding may be caused by the operation of slip crossing the grain boundaries. Supporting evidence for this model from other investigations is also given. GRAIN boundary sliding in metals during elevated temperature deformation has frequently been thought of as an independent mechanism with its own characteristic stress, temperature, and structure dependence. Further, it is common to regard the grain boundary as the weak link during creep deformation since: 1) the strength of apolycrystallinemetal, as meas-sured by creep rate or rupture life, decreases at\a more rapid rate when sliding comes into action, and 2) grain boundary sliding, as revealed by "boundary darkening" and fold formation is often the first visible deformation. On the other hand, more quantitative observations, in both polycrystals and bicrystals, have shown boundary deformation to be closely related to the over-all deformation of the specimen. The curve of grain boundary contribution to elongation vs time takes a shape similar to that of the total creep curve,',' and the apparent activation energy for sliding appears in most cases to have the same value as that for total creep.3 In order to reconcile these observations, one is left with these possibilities: 1) The grain boundary and grain deformation rates are both controlled by the same rate limiting processes. 2) The rate of sliding is limited by accommodation deformation in the grains. 3) Sliding is the consequence of grain deformation. 4) Grain deformation is dependent on prior grain boundary deformation. Alternatives 2) and 3) would view grain boundary sliding as occurring in series with another deformation process which could be rate controlling. McLean prefers item 3) as the sliding basis,4 where subgrain rotation results from dislocation accumulation in the substructure at the grain boundary. Crussard and Friedel's5 treatment of grain boundary migration considers that dislocations are forced into the grain boundary and are dissociated into dislocations with Burgers' vectors nearly parallel to the grain boundary. The movement of these partial grain boundary dislocations then produces the sliding. The results of this investigation have indicated alternative 3) to be the most appropriate and it is this aspect of grain boundary sliding which will be analyzed. EXPERIMENTAL PROCEDURE Three types of tensile creep tests were employed in this study: (I) A constant load test of one very coarsegrained polycrystalline specimen at 500° F, 3600 psi, 1 pct per/hr strain rate to examine the grain and grain boundary orientation factors in grain boundary sliding. (II) Constant strain rate tests of polycrystalline specimens at 510o and 715o F, 2 pct per/hr strain rate to determine the grain boundary contribution to elongation at very low total strains. (m) Constant strain rate tests of bicrystals of various grain and grain boundary orientations at 500°F, 2 pct per/hr strain rate to obtain further information on the orientation effects in grain boundary sliding. The material used in the tests was a high-purity Al-1'.92 mg alloy, kindly furnished by Alcoa. Its composition is given in Table I. The alloy is a solid solution at the test temperatures. The coarse grained polycrystalline specimen for test (I) was prepared by recrystallizingthe machined specimen, straining it about 1pct intension at room temperature and annealing at 900°F for 8hr. The constant strain rate specimens (11), with an 178 in. sq. by 1/2 in. long gage section, were cut from 1/8 in. thick sheet of cold rolled and annealed (8 hr at 1000oF) material. The latter specimens were supported in a special jig during the milling operations to avoid any bending, and the gage section was subsequently heavily electropolished to remove the cold-worked surface layer. The bicrystals (ID) were machined in the same

Jan 1, 1963

By J. A. Woolf, E. S. Leaver

THE purpose of this paper is to describe, in a general way, gold-dredging operations in California, with particular reference to unusual features, including types of deposits and recent attempts to improve the recovery of the gold. Dredging Areas The gold-bearing formations that traversed the western slope of the Sierra Nevadas for a north and south distance of some 300 miles furnished the immediate source of the gold found in most of the placer deposits of California. Erosion through a long period carried the gold, together with various forms of partly disintegrated material, to lower elevations and formed placer deposits. Through the classifying action of water in motion, the coarser gold and heavier material of various kinds were - deposited relatively near the source; consequently, in the higher mountain country, old river channels were worked feverishly during the early California gold-rush days because of their high gold content. With the working out of these known high-grade channels, and from the knowledge thus obtained of prehistoric stream beds, drift mining was started and flourished until about 1890. Even today many drift mines are operating with the objective of opening other old Tertiary river channels that have been covered by volcanic flows. Adjacent to these areas, which contained relatively high gold values in the older river channels, smaller particles of gold, gravel, and debris were deposited along the sides of the former stream beds and on the adjoining flat areas, thus forming the large placer deposits, which were worked principally by hydraulic mining. Following the course of the ancient rivers and of the present drainage system to the lower edge of the foothill country, extensive areas of alluvial

Jan 1, 1937

By R. J. Arsenault

The yield drop that occurs in tantalum, Cu-AZ. and Ag-Al was investigated as a function of strain rate and at several temperatures. From the strain-rate dependence of the yield drop an activation volume was calculated and found to agree with that obtained from differential strain-mte tests. The temperature dependence of the yield drop can he explained in terms of the parameter temperature divided by activation volume. The yield drop is attributed to the rapid multiplication of dislocations during their motion. THE yield-point or yield-drop (upper yield stress minus the lower yield stress) phenomenon has been the subject of numerous investigations1-9 in both bcc and fcc metals. Also, there is no dearth of theoretical explanations10-20 to account for the yield-point phenomenon. The present explanations can be divided into two categories: the concept of dislocation locking and subsequent unlocking and the concept of multiplication of dislocations due to their motion. The Vottrell10,11mechanism of locking and unlocking, as applied to bcc metals, is the best known of the three proposed locking mechanisms. The two additional mechanisms, short-range order (SRO)7,16,17 and Suzuki-type locking,14,15 have been employed to account for the existence of yield points in fcc metals. The experimental evidence supporting the locking of dislocations, especially in bcc metals, is well-established. The dependence of the yield point on interstitial concentrations,' the kinetics of strain aging,2 and the observations by electron-transmission microscopy18 are some of these experimental results. The number of experimental observations supporting dislocation locking in fcc metals is not as extensive as in bcc metals. The unlocking of dislocations, which actually is supposed to account for the yield drop, is by no means well-established by experimental results for either bcc or fcc metals. The similar temperature dependence6 of the yielding and plastic flow is one of the experimental factors that cannot be explained in terms of the unlocking of dislocations. The mechanism based on the rapid multiplication of dislocations has been proposed by several investigators. 18-20 Johnston and Gilman19 have proposed a detailed model of yielding, which was later employed by Hahn21 to predict quantitatively the yield drop in iron. This mechanism was discussed in a previous paper22 and several limitations were pointed out. In the same paper it was shown that an activation volume could be obtained from the strain-rate dependence of the yield drop and that a correlation existed between the activation volumes obtained from the yield-drop tests and from differen-

Jan 1, 1964

By Edward W. Parker

At the Seventy-sixth meeting of the Institute, held in New York, N. Y., February, 1899,I presented a paper on this subject entitled, Coal-Cutting Machinery,' which has become somewhat out of date, in view of the decade's development in this feature of the coal-mining industry. It should be explained that the present paper is limited to the use of mining-machines in bituminous mines. Practically all of the anthracite mined is "shot from the solid," no undercutting being done. Anthracite-mining is therefore not considered in the statistics or other references. The statistical record as compiled by the U. S. Geological Survey shows that in 1898, the year preceding the presentation of my former paper, there were 32,413,144 short tons of coal undercut by the use of machines. In 1907 the machine-mined coal-product amounted to 138,547,823 short tons. In sympathy with the general decrease in coal-production during 1908, the output of machine-mined coal decreased to 123,183,334 short tons, but the proportion of machine-mined coal to the total output, nevertheless, showed an increase, from 35.1 per cent. in 1907 to 37 per cent. in 1908. In 1898 only 19.5 per cent. of the total product was unclercut.by the use of machines. The number of in use in the bituminous mines of the United States has increased from 2,622 in 1898 to 11,144 in 1907, and to 11,569 in 1908. The total production of bituminous coal in the United States in 1908 mas almost exactly double that of 1898, while the machine-

Jan 1, 1911

Large equipment for quarrying and for the various stages of crushing and grinding are the trend for new and existing operations. Included are large size haulage units, fast drilling equipment, impact crushers and large mills capable of high tonnage rates for metallic and nonmetallic minerals. In grinding, large-size mills continue as the choice in industries where grinding constitutes a major portion of the processing. Typical is a 10 x 34 ft two-compartment mill in closed circuit with an 18-ft diam air separator for cement. Other cement mill sizes are in the order of 12 x 36 ft, 2500 hp; 10 x 37 ft ball and rod (wet), 1400 hp; 13 x 36 ft, 3000 hp; 13 x 40 ft (wet), 3000 hp. Several installations of combination ball and rod mills have been made, and one of the largest is 12 x 45 ft. In connection with the wet grinding of raw materials, the DSM 270-degree screen has been installed in several cement plants with the intention of producing a material finer than 50 mesh. In ore processing, large autogenous mills (121/2 x 20 ft) are being installed.

Jan 2, 1964

By Robert Anderson

The diffraction of x-rays by cold-worked and heavily polished surfaces of metals gives, no evidence of an amorphous state and typically perfect crystallographic diffraction' patterns are obtained. Severely cold-worked metals, reduced as much as 98 per cent. in area, give true crystallographic diffraction patterns, and polished surfaces of large single crystals of metal give typical crystallographic patterns. The conclusion is drawn, on basis of x-ray evidence, that metals are fragmented on cold work and polishing and not amorphized. THE purpose of this paper is to report evidence, regarding, metal: structures, that is contradictory to the amorphous-metal, hypothesis of Beilby, and particularly evidence that is opposed to the proposition that a vitreous amorphous layer is produced by polishing a piece of metal. According to the theory of Beilby, which has been developed, by Rosenhain and others, polishing a piece of metal greatly affects the condition of the metal at or near the surface polished, making that surface entirely different in character from the metal beneath. A vitreous amorphous surface film is said to be formed. The polishing process, on the basis of Beilby's explanation, is well known-and does not' require discussion here, but it is advisable to seek the precise meaning of,., the term "amorphous." According to Beilby, "amorphous means. Non-crystalline in the most intimate sense of the word'; the molecules are not marshalled in crystalline order and orientation." According to Rosenhain, the amorphous condition is that assumed by a metal when, the .crystalline arrangement is completely broken up so that the atoms exist in a state of disorderly arrangement similar to that ;which exists in the liquid state. Thus, from the point of view of the phase rule, the "amorphous phase" is regarded as being identical with the liquid phase. Amorphous metal is often likened to an undercooled liquid. A crystalline substance is one in which the atoms are arranged in space according to some definite repeating geometrical pattern. The existence of amorphous metal has not been definitely proved.

Jan 1, 1925

By R. L. Templin

The increasing use of aluminum and its alloys in commercial fields tias demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure alunlinum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual tools. Comparison oF Cutting Tools Cutting tools commonly used for machining free cutting brass usually have little, if any, top and side rake; they are ground on a medium to coarse abrasive wheel and used without any cutting compound or with a cutting compound that has a paraffin base. Those ordinarily used for steel have some top and side rake, are usually ground on a medium to fine abrasive wheel, and are often used with soluble-oil cutting compounds. The proper tools for aluminum and its alloys should have appreciably more side and top rake than the tools for cutting steel; should have very keen edges obtained by grinding with fine or very fine abrasive wheels supplemented in many cases by hand stoning with an oil-stone; and should be used with suitable cutting compounds whenever possible. In many cases, tools suitable for machining aluminum and its alloys are not appreciably different from tools commonly used for cutting hardwoods. The front clearance of a tool most suitable for machining aluminum and its alloys should be about 6°, the top rake from 30" to 50°, making the total angle of the cutting edge of the tool from 35' to 55". A side

By G. C. Gould

The nature of freckle segregation is determined by chemical analyses, microradiograplzy, and electron microprobe. In addition, the influence of chemistry variation on freckle formation is studied in laboratory experiments. It is demonstrated that controlled laboratory solidification can produce freckle segregation. "FRECKLE" segregation is a discontinuous, rod-like segregation observed in vacuum consumable -electrode ingots. Figs. 1 and 2 show this segregation as pencil-like, dark etching areas of segregation found in longitudinally and transversely sectioned consumable-electrode ingots. In most cases the segregation is perpendicular with respect to gravity and parallel to the longitudinal axis of the ingot. The segregation is most often encountered at or around midradius in large vacuum consumable-electrode ingots. The austenitic alloys, A-286* and 718, † have shown particular susceptibility to this mode of segregation. The origin of these rodlike pockets of segregation is not well-understood. It has been suggested that the segregation is a result of a portion of the electrode dropping off and passing through the arc un-melted. On the other hand, smeltzer1 has demonstrated the freckle segregation in A-286 to be comprised of low-melting constituents relative to the matrix melting point. The discontinuous nature of the segregation is the most perplexing facet of the freckle-segregation problem. It was to gain some insight into this part of the problem that this work was undertaken. I) PROCEDURE At the outset of the work identification of the phases present and the elements concentrated in the freckle areas was undertaken. The electron micro-probe was used to determine general enrichment as well as -specific phase chemistry. Microradiography using cobalt and chromium radiation was also used on the freckle areas again to determine the elements involved in the segregation. X-ray diffraction patterns were made from portions of these same foil specimens. Optical microscopy and Knoop hardness measurements were also used

Jan 1, 1965

By R. S. Hooper

IN attempting to describe recent mining developments at the Bunker Hill mine, it may be well to recall first the old days of hand mining when holes were laboriously drilled by hand to a maximum depth of three feet, and were shot one or two at a time, in order that the miner could take advantage of every slip, crack or bedding plane, and so save as much drilling as possible. Broken muck, of course, was loaded by hand shoveling into wheelbarrows or small cars, and heading advances or stope ton¬nages were governed by the number of men that could find room to work in any given place. The first big improvement over these old methods was the introduction of the reciprocating type of air-powered rock drill. This innovation, crude as it was, enabled the miners to set up a machine and drill a complete round of holes in one shift; but broken muck was still loaded by hand, and the size and rate of advance in headings were limited by time required to remove the broken rock. The next improvement of consequence was the appearance of the hammer-type rock drill, which greatly increased drilling speed over the reciprocating type, and made possible the completion of a full cycle in one shift, by the use of crossbars in headings, and permitted drilling and mucking to be carried on at the same time. Rock drills continued to improve as time passed, and finally the smaller and more efficient mucking machines appeared on the scene, and it became possible to muck out a round of broken rock and have a clean setup for one or more drill columns and machines. A complete cycle of mucking, drilling, and blasting was completed in one shift with an average advance of five feet. These conditions prevailed for several years, but as the mine grew deeper, the distances to transport the workers grew longer, and this fact together with the shortening of the working day, soon presented the problem of attempting to complete a cycle of operations in a shift of only six hours at the working faces. Anticipating this condition, the operating heads at the Bunker Hill had started an intensive study of more and better mechanization, and over a period of comparatively few years have adopted and placed in service methods and machines that make it possible for a three-man crew to consistently advance headings seven by nine feet in cross section, at the rate of eight feet, and more, per shift, doing all the mucking, switching, drilling and loading. These improvements consist of the following major items: I. The development of a light, flexible, easily transported jumbo equipped with pneumatic columns (Fig I), that has decreased the "setting up" and "tearing down" time an average of 1 1/2 hr per shift, or 25 pct of the available working time. These jumbos were developed at the Bunker Hill mine by members of the staff and consist of two pneumatic columns attached to a suitable carriage. They fold

Jan 1, 1947

By A. M. Sarem

For the performance prediction of multiphase oil recovery processes such as steam stimulation, there is an acute need for three-phase relative permeability data. No fast and simple experimental technique, such as the unsteady state method proposed by Welge for two-phase flow, is available for the three-phase flow. In this paper, an unsteady - state method is presented for obtaining three-phase relative permeability data; this method is as fast and easy as Welge's method for two - phase flow. Analytical expressions are derived by extension of the Buckley-Leverett theory to three-phase flow to express the saturation at the outflow face for all three phases in terms of the known parameters. It is assumed that the fractional flow and relative permeability of each phase are a function of the saturation of that phase. Other simplifying assumptions made include the neglect of capillary and gravity effects. The effect of saturation history upon relative permeability is acknowledged and attainment of similar saturation history in laboratory and field is recommended. The required experimental work and computations are simple to perform. The test core is presaturated with oil and water, then subjected to gas drive. During the test, required data are the rates of oil, water, and gas production, together with pressure drop and temperature. The ordinary gas-oil unsteady-state relative permeability apparatus can be readily modified to measure the required data. The proposed technique was applied to samples of a Berea and a reservoir core. The effect of saturation history upon relative permeability was studied on one Berea core. It was found that increase in initial water saturation has a similar effect upon three-pbase relative permeability as it does in two-phase flow. INTRODUCTION In the light of increasing demand for three-phase relative permeability data for predicting the performance of thermal and other multiphase-flow recovery processes, a simple and accurate method of experimental determination of such data is extremely desirable. Leverett and Lewis 1 described the simultaneous flow method of obtaining three-phase relative permeability data. However, Caudle et al.2 reported that this method is very time consuming and cumbersome. Corey3 proposed calculating the three-phase relative permeability from measured krg data. Corey's theory is based on simplified capillary pressure curves,4 assuming a straight line relationship between I/Pc2 and saturation. Also, Corey's method assumes a preferentially water-wet system. The simplest and quickest method of obtaining three-phase relative permeability data is the unsteady-state method where, for instance, oil and water are displaced by gas. However, in such a test the correlation of average saturation with relative permeability does not give a valid relationship because the rates of oil, water and gas flow in the sample change continuously from the upstream to downstream end. This difficulty in calculating valid relationships was solved by Welge for two-phase flow by deriving an expression for determining the outflow face saturation from Buckley and Leverett frontal advance equations.5,6 In this paper, relations are established to determine the outflow face saturation and relative permeability to all phases in a three-phase flow displacement experiment. PROPOSED METHOD The fundamentals established by Buckley and Leverett5 for two-phase flow were extended to three - phase flow and used as a basis for the derivation of saturation equations. This approach is comparable to Welge's6 use of Buckley and Leverett theory in arriving at expressions to determine the outflow face saturation of the displacing fluid in a two-phase flow system.

Jan 1, 1967

By W. L. Phillips

The plastic properties of lithium fluoride and magnesium oxide under compression were investigated in the temperature range 25° to 1000°C. At the higher test temperatures, the critical resolved shear stress and the rate of work-hardening of both materials decreased. At the same time, the number of stress lines decreased and the individual stress lines became wider. The density of dislocations decreased for a given strain the higher the test temperature for lithium fluoride. The decrease in the critical resolved shear stress as a function of temperature could be fitted by the equation 7 = Toe-KT. THE influence of temperature on the stress-strain curves of a variety of metal single crystals has been studied for a wide range of temperature.1"5 In general, it has been found that both the critical resolved shear stress and the rate of work-hardening decrease rapidly with increasing temperature and fall to a value of essentially zero well before the melting point is reached. AS the test temperature is increased, the density of slip lines has been found to decrease, while the width of the individual lines increases. Recently, Gallagher,' Graf et al.,7 and Pate1 and Alexander8 have found that single crystals of germanium and silicon, which have a covalent bond, can be plastically deformed at elevated temperatures. In compressing germanium it has been found that the strain-hardening coefficient decreased very rapidly as the temperature was increased. The coefficient did not tend to zero, however, as the melting point was approached. The plastic properties of ionic crystals at elevated temperatures have not been extensively investigated. In the only work previously reported Tamman and salge9 and Theile10 have shown that the yield point of sodium chloride single crystals tested in tension and compression decreased slowly with increasing temperature, falling to zero at the melting point. As the temperature was increased, they found a substantial increase in the amount of plastic deformation that could be sustained before fracture; and at temperatures above 400°C in tension tests there was an obvious necking which produced local extensions of up to 3000 pct. The purpose of the present work is to extend the knowledge of high-temperature deformation to the ionic crystals, lithium fluoride and magnesium oxide. The following were investigated: 1) The gross shape of the stress-strain curve at several temperatures. 2) The change in the critical resolved shear stress as a function of temperature. 3) The appearance of slip bands and the density of dislocations as a function of strain and temperature. EXPERIMENTAL TECHNIQUES The lithium fluoride and magnesium oxide used in this investigation were purchased from the Harshaw

Jan 1, 1961