Search Documents

Jan 1, 1969

By Don K. Smith

The Reclamation Program for the Northern Zone of the Indus Plains in West Pakistan involves the construction of 30,000 irrigation wells to serve 20 million acres with an annual pumpage of nearly 40 million acre-ft. Detailed hydrologic studies indicated that mild steel would be satisfactory for casing; however, within two years after construction, about 10% of the wells began to fail due to encrustation and corrosion of the casing. A search to find a noncor-rosive substitute for the steel casing disclosed that only fiberglass-reinforced plastic pipe satisfied all requirements. The results of initial use of fiberglass have been highly satisfactory and have resulted in a lower over-all well cost. Advances in technology pomise further reduction in prices and improvement in performance. The northern zone of the Indus Basin comprises a vast area of essentially level land in West Pakistan which is irrigated by means of a complex system of canals that distribute more water to more land than any other irrigation system in the world. In spite of the development of this extensive irrigation system, production of food and fiber has not met the requirements of the country. The major reasons that crop production has not reached anticipated levels are the lack of adequate irrigation supplies and effective subsurface drainage. As a result, yields per acre are among the lowest in the world for areas where irrigation is practiced, and many thousands of acres of valuable crop land have been removed from production or seriously affected by salinity and waterlogging. To rectify the problems of irrigation supply and drainage the Government of Pakistan has undertaken a program of Salinity Control and Reclamation which is being administered by the Water and Power Development Authority. The Authority retained Tipton and Kalmbach, Inc., of Denver, Colo., as engineers for the program in the northern zone of the Indus Basin. This program consists of the construction of about 30,000 irrigation wells to provide drainage for waterlogged lands and full irrigation supplies, including leaching requirements, for all cultivated lands. The program will ultimately ensure the productivity of 20 million acres and involve an annual pumpage from groundwater storage of nearly 40 million acre-ft of

Jan 1, 1970

By C. E. Gerity

Near Bunker, Mo., in the New Lead Belt, Ozark Lead Co. operates a 6000 tpd lead-zinc mine. Mined ore is transported to the surface in three mechanized and automated steps. The mine is developed by a rectangular-shaped sublevel haulage drift 15 ft high by 28 ft wide, driven on strike below the ore zones. Ore transfer raises were driven from the sublevel at locations near the shaft, 1500 ft distant, and on subsequent 1000 ft centers. These 6 x 5-ft raises are slashed to obtain maximum storage below dump points. These dump points are located on each mining level and are of steel and concrete construction. Spiral 12 X 24-ft inclines driven from the sub-level provide access to these levels for equipment and mine utilities.

Jan 11, 1972

By Thomas Leonard Watson

Jan 1, 1906

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By F. Petkovich, M. P. Sudbury

Development of a new method of treating flotation concentrates for the preparation of feed suitable for direct charging to blast furnaces or converters is described. The method takes advantage of the fact that pyrrhotite contained in the concentrates can be made to undergo exothermic reactions which, under properly controlled conditions, result information of oxidation products that serve to cement the concentrate particles together. Thus green concentrates either in the form of pellets or briquettes containing 5 to 8 pct moisture not only were hardened, but also completely dried autogenously by continuous countercu,vrent shaft treatment with air. The process was developed through pilot plant operations ranging from 35 1b per hr to 2.5 tph, culminating in products evaluation tests on a railway-car scale. Falconbridge Nickel Mines Ltd., Falconbridge, Ont., have practised sintering, on a travelling grate machine, for many years to prepare a pyr-rhotite-bearing Cu-Ni sulfide flotation concentrate for blast furnace smelting. In recent years the development of new mines, and the construction of concentration plants some 40 miles from the smelter has increased the quantity of concentrate shipped, and encouraged the search for a method of producing dry, hard pellets or briquettes suitable for direct charging to a blast furnace or converter, and capable of withstanding considerable handling. The cementing properties of pyrrhotite oxidation products were discovered during a search for a suitable agglomeration method for sulfide concentrates, and were exploited in a process subsequently developed for autogenously drying and hardening pellets and briquettes of pyrrhotite-bearing Cu-Ni sulfide flotation concentrate. EARLY TEST WORK The production of hard, dry pellets of concentrate filter cake was attempted in the drying plant of one of the new concentrators. While soft pellets were produced containing 5 pct moisture, attempts at further drying resulted in disintegration of the pellets and intolerable dusting. The plant therefore was controlled to produce a concentrate containing about 6 pct moisture. The partially dried concentrate, which was shipped to Falconbridge for sintering, tended to heat spontaneously in transit. An at- tempt to briquette the moist concentrate at Falconbridge, in a plant incorporating a muller, a 20-in. roll briquetting press, and a steam-heated travelling grate oven, was more successful, although the equipment corroded rapidly due to the acid nature of the concentrate after spontaneous heating had occurred. LABORATORY STUDIES OF SPONTANEOUS HEATING OF CONCENTRATE The spontaneous heating of partially dried concentrate was studied in the laboratory. Moist concen-

Jan 1, 1961

By J. C. Detweiler

THE Jacksonville plant of Humphreys Gold Corp., operating under leases from National Lead Co. and Rutile Mining Co. of Florida, recovers rutile, ilmenite, zircon, and monazite from an ancient beach deposit containing about 2.5 pct of these minerals in combination. The location of the plant is unique, being situated about ten miles from the center of Jacksonville, Fla., surrounded by a thriving suburb. Two four-lane highways pass within 1 ½ miles of the plant. An expressway now under construction will pass over the tailing pile, within 500 ft of the mine office. The elevation at the plant site is approximately 50 ft above sea level. This is one of two mines producing titanium minerals and zircon in Florida. Another mine is also operated by Humphreys at Starke, about 50 miles southeast of Jacksonville. The Jacksonville deposit extends about six miles in a north-south direction, averaging approximately one half mile wide and twenty ft thick. Values begin at the surface over most of its length and ter-

Jan 1, 1952

By Ernst M. Cohn

The demonstrations of the "Silent Sentry" by Union Carbide Corp. in 1957 and of a special tractor-plow by Allis-Chalmers in 1959 ushered in the technology era of fuel cells. The idea for direct conversion of chemical to electrical energy, first published in 1801 by Davy in England and Ritter in Germany, has been kept alive by a few people through 150 years: Grove built the first hydrogen-oxygen fuel cell in 1839; Mond and Langer made electrolyte contributions around 1890 that are still used today; Baur worked on coal-based cells from 1900; Bacon started his work in the '30's, which resulted in the first multi-kilowatt unit in the '50's; Davtyan studied molten-salt electrolytes in the '40's, followed by Ketelaar in the '50's; and Justi developed highly active electrodes in the '50's, to name only some of the pioneers. Despite the tremendous increase in research and development of fuel cells, these direct energy converters are still in their infancy. They will find their functional application in space, where power density must be maximized and product water utilized. These early systems will provide valuable experience in system engineering and reliability.

Jan 9, 1964

By Peter F. Weiss, H. Riedler, I. M. Moschitz, A. Olsacher, G. B. Fettweis

CONTENTS : 1. NATURAL FACTORS Geology Petrography and Rock Mechanics Mining System Orientation Rock Bolting System Movability of the Ore Grain Size Distribution Permeability Contamination Value of the Ore Hydrology 2. TECHNICAL FACTORS Height Length and Width Drawing Areas Time Factor Water Predrainage Surf ace Draining Underground Draining Advancing Slitting Sequence of Development Initiation of the Caving Process Drawing Rate 3. SPECIFIC MINING RULES Advancing Development Drawing Rate Interruption of Drawing (Water Distribution, Concentration of Mud, Dilution) Blasting 4. CONTROLS Safety Controls for Operation Computerised Drawing Control Structure of the Computer Program Hard Ware Print Outs 5. SUMMARY 6. ACKNOWLEDGEMENTS 7. REFERENCES Under the heading "Development System for Block Caving under Severe Conditions" a report was presented to this congress regarding a magnesite mine using block caving for several years. On account of the experience gathered in this mine and the results of far reaching exchange of experience, as well as under due consideration of the international literature it is tried to systematically list and briefly discuss the following factors that have to be considered for development and draw control of block caving. 1. NATURAL FACTORS It is self evident that this implies all those circumstances given by nature and which cannot be altered by man. Any mining activity is subjected to those and the success is depending on how far technology can be adjusted to those conditions. Geology Deposits of considerable thickness with rather steeply inclined flat-faced contacts are optimal for block caving. While vertically there is practically no limitation- for the deposit, theoretically, the smallest horizontal basis apt for operating block caving is the minimum area necessary to get the rock to completely cave in by undercutting and drawing. Practically, only consider- ably bigger main dimensions are found, mainly because of technical factors (machinery and equipment) and economic factors (cost ratio of exploration vs. development, danger of contamination).

Jan 1, 1981

By A. A. Toprac

The recurring problem of joint failures in ofjshore structures, coupled with the catastrophic collapse of many of these structures during Hurricane Hilda (1964), hay forced reconsideration of techniques presently used to design sfuctural joints. This paper presents results of studies conducted for this reconsiderat?on. Only right-angled T-joint,s and cross-joints where a brace was welded directly to the undisturbed surface of another tube (the chord) were considered. Tests were performed on seven T-joint and 12 oross-joint specimens of two types which were designed to give a broad but practicd range to the geometrical parameters believed to be of significance to the problem. These paramefers were expressed in dimensionless form. Each specimen of the T-joints was instrumented wirh both electrical resistance strain gauges and deflection dials. After the elastic tests were concluded, each specimen was loaded to failure by applying an axial tensile load to the brace. The cross-joints were tested to failure without measuring elastic strains. Theoretical solutions for the stresses in a cylindrical shell due to a distributed radial load over portions of its surface were numerically evaluated. The experimental results are compared with calculated values obtained using Bijlaard's and Dundrova's theoretical analyses. INTRODUCTION During the last IS years a large number of structures were built for the offshore exploration of oil both in the Gulf of Mexico and dong the Pacific Coast.' In all these offshore platforms, the tubular shape was extensively used since this shape provides outstanding strength in proportion to its weight, compared to other shapes, when all directions (x, y, z) are considered. Past use of tubes was hampered because of connection details. But with the advent of welding, it became no more difficult to connect tubular shapes than to connect rolled shapes. However, some problems have been encountered in actual construction in making welded joints that are adequate and yet economical. In trying to connect tubular members, designers have used a varied number of methods; consequently, some of the joints seem to be very expensive in detail while others appear weak and underdesigned. An inspection of offshore platforms owned by different companies indicates the use of a large number of joint arrangements and configurations. Such a variety of joint types in current service indicates the wide divergence of opinion that exists on how such joints should be designed, stiffened and strengthened. Fig. 1 shows the various types of connections that have been used in practice. This paper reviews the present state of art on tubular joints of the T and cross type, and presents results of experimental and analytical work being conducted at The U. of Texas and elsewhere. It is believed that such information will be of great help to designers for the formulation of proper design procedures for joints. CONNECTION PROBLEM Recently, cracks have been observed in several welded connections in offshore structures. Fortunately, until about 1 1/2 years ago, these failures have been localized and have not resulted in the collapse of structures or loss of life. For example, one platform installed in Louisiana during 1955 in about 60 ft of water had been subjected to four tropical hurricanes. This platform successfully withstood these forces and was later removed because operations at this location had been completed. Many joint failures were observed during the removal.

[Chairman ZAY JEFFRIES, Vice-chairman S. SKOWRONSKI, Chairman WILLIAM M, CORSE, Secretary Executive Committee J. R. FREEMAN, JR., Local Section G. E. JOHNSON R. S. ARCHER, Non-ferrous Data Sheets P. D. MERICA EDGAR C. BAIN, Journal Committee L. W. SPRING SAM TOUR, Papers Committee F. L. WOLF H. C. JENNISON, Membership Committee Local Section Committee J. R. FREEMAN, JR., Chairman R. J. ANDERSON, Cincinnati R L. DOWDELL, Minneapolis R. S. WILLIAMS, Boston G. H. CLAMER, Philadelphia W. A. SCHEUCH, Chicago R. F, Woon, New York Papers Committee S. SKOWRONSKI, Chairman F. H. DIx, JR.-Aluminum E. R. DARBY-Bronze C. S. WITH ERELL-Copper H. A. BEDWORTH-Brass W. K. FRANK-BRONZE F. W. HARRIS-Copper R. L. SUHL-Nickel H. M. ST. JOHN--Foundry Metallurgy R. S. DEAN-Theoretical Metallurgy]

Jan 1, 1928

By T. S. Washburn

THE grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure-killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes are not present. Also, the rimmed ingot has no well defined pipe, as com-pared to the deep pipe on the killed ingots, and there are numerous pri-mary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differ-entiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7-as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined or deep as in the killed ingot of Fig. 1. In killed ingots, pri-mary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company's smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 ¼ miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1938

By Henry Howe

THIS paper is a discussion of the extremely valuable one of Mathewson and Phillips, The Recrystallization of Cold-Worked Alpha Brass on Annealing,1 which not only gives us a wealth of important data reached with great intelligence, but also shows both uncommon powers of imagination and a perfectly fair spirit. Let me try to analyze some of their results, and to enunciate some of the laws to which these results point. For brevity I refer to them as "The Authors." The page numbers in parentheses refer to their paper. 1. The Visible Aspects of Recrystallization.-Plastic deformation in a single direction, as in cold-rolling, draws the grains out in that direction, that is, inequiaxes them, without destroying their apparent individuality. Each grain seems to endure the drawing out without changing either its volume or its orientation materially, for the etching tint of each grain seems to be as uniform after as before the drawing out, save for the "etch bands,"2 shown in Figs. A to D of the Authors' Plate I. As the drawn-out metal is heated progressively, on reaching a certain "disintegration temperature" these old grains seem to break up, probably into submicroscopic fragments, and this apparent disintegration is followed by a coalescence of these fragments, so that their number decreases and their size increases, till they may become very much coarser than before the drawing out. Ruder3 coarsened the grains of silicon steel in this way till single grains reached an area of 50 cm. (7.75 sq. in.). The deformation itself probably breaks each grain up into many very small fragments, but the fact that each grain continues to have a uniform etching tint different from that of its neighbors indicates that these fragments retain the initial common orientation of the grain. The apparent disintegration which we observe, then, is rather an abandonment of community of orientation for individuality of orientation, by the fragments formed earlier during the deformation. Hence we

Jan 10, 1916

By J. L. Green

Virginia-Carolina Chemical Corp., in its Florida Operations, uses both roller mills and ball mills in dry grinding of phosphate rock. The roller mills have been in operation since 1954 in the Mining Department. The ball mills were installed and put in operation in 1960 in the Harding Concentrate Superphosphate Plant. The roller mills in the Mining Department are used to grind phosphate rock for outside customers. This involves short notice orders of varying grinds, grades and types of rock. The ball mills grind phosphate rock for use in V-C's own phosphoric acid and concentrated superphosphate plant. These mills grind generally two types of rock for one grind. In 1959, a 10% speed-up was made in the operating speed of the roller mills. This paper deals with the operational gains and resulting cost savings which evolved from this speed-up, and compares the present operations of the roller mills and of the ball mills in grinding phosphate rock. In January 1959 it was decided to determine the feasibility of reducing the grinding cost on the roller mills, per ton of rock ground, by speeding up the mill 10%. At this time, one mill was completely reconditioned so it would be in top condition. Extensive tests were then run both before and after the mill speed-up to determine the resultant cost savings. These tests showed that, due to this 10% speed-up, the mill capacity was increased approximately 20% and grinding power costs per ton were reduced approximately 10%. Table I shows the results of these tests. Each test run actually represents several of the same type rock and grind, averaged together. Each test run lasted approximately three hours. The validity of these runs has been confirmed by subsequent operation in grinding over 1,000,000 tons of phosphate rock. Accurate records have been kept on power consumption and repairs as well as tons produced. Two types of feed rock were used for the tests — pebble phosphate rock and flotation phosphate concentrate rock. The pebble phosphate rock size is approximately 80-90% plus 20 mesh. The flotation concentrate phosphate rock size is approximately 15% plus 20 mesh and 95% plus 100 mesh. The same two types of rock feed were used for all the test runs. Test Nos. 1, 2, and 3 were run at the original mill speed of 85.5 rpm on the vertical shaft. Test No. 1 was run with a feed of high grade flotation concentrates; the desired fineness attempted was 70% passing 200 mesh. Tests No. 2 and No. 3 were run with a feed of low grade pebble. Test No. 2 was run for a desired fineness of 70% passing 200 mesh. Test No. 3 was run for desired fineness of 50% passing 200 mesh.

Jan 1, 1963

By C. B. Foster, S. I. Freedman, E. M. Jamgochian

Coal-oil mixture (COM) combustion technology is regarded by the US Department of Energy (DOE) as near term and Potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers and blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1980

By L. T. Stanley

A method is described whereby the behavior of the front is approximated when gas is injected into a thick reservoir having reasonably homogeneous properties. The method is applied to the Abqaiq field of Saudi Arabia. The producing member is the Arab-D, a high-permeability calcarenite which has no continuous betlding planes. Field performance indicates the injected gas to be partially miscible with the reservoir oil because gas volume factors experienced are lower than those predicted by the gas law. Eqlrilibril~m calculations confirnz ihis and also show that the volume factor may vary appreciably, depending on the relative quantities of oil and gas in contact in the reservoir; consequently, volutnetric balances are made for the purpose of determining the behavior of the gas volume factor during injection history. The effect of gravity segregation on position and shape of the gas front is approximated by dividing the producing section into three zones vertically and tracing the movement of the average interface in each zone, with counterflow of oil and gas taking place betweell zones behind the front. This results in a gas front that advances more rapidly along the top of [he formation than along the base, producing an "umbrella" effect in cross section that becomes more pronounced as the front progresses. The calculations cover the gas-injection period of Abqaiq field history through 1958, and the position of the gas front is plotted at one-year intervals. Finally, some comparisotls between the calcrlated fronial position and the gas-oil contact as Measured by neutron logs are made. INTRODUCTION Fig. 1 is a structure contour map of the Abqaiq field. For analytical purpcses, the field has been divided into two areas designated A and B, as shown on the map. Gas injection into Area A was begun in early 1954 into two wells located near the crest of the structure on the north-south axis of the anticline. During the period covered by this paper, the average injection rate has been 122 MMscf/D with a maximum sustained rate of 160 MMscf/D. The reservoir pressure has been maintained at 2,450 psig since start of gas injection. The reservoir originally was undersaturated but, prior to pressure maintenance, the pressure was drawn below the bubble point in most of the Area A section, creating an in-place free-gas saturation of 8 per cent at the crest of the structure. The average critical gas saturation is 13 per cent established by laboratcry core tests. That the entire reservoir remained below critical gas saturation prior to gas injection is borne out by the fact that none of the crestal wells have exhibited high gas-oil ratios during production history. The Area A reservoir is a carbonate section about 200-ft thick having average porosity and permeability of the order of 22 per cent and 500 md, respectively. The productive horizon is the Arab-D member of Jurassic age and is encountered at an average depth of

By H. R. Hanley

The characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previosly ously in the literature.' This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors1 previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (I) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calciurn-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent. * Professor of Metsllurgy, Missouri School of Mines. t Professor of Metallurgy and Ore Dressing, Hea.d of Department, Missouri School of Mines. Assistant Professor of Metallurgy, Missouri School of Mines. 1 Among others, see C. G. Fink and Li Chi Pan: Insoluble .Anodes for the Electrol-ysis of Brine [Trans. Amer. Electrochem. Soc., (1926) 49, 83-1341 and other papers by these authors. U. CJ. Taintori, 8. G. Taylor arid H. P. Ehrlinger: Lead Alloys for Anodes in Electrolytic Production of Zinc of High Purity. Truns. A. I. M. E. (1929) 192-200. 2 H. R. Hanley, C. Y. Clayton, D. F. Walsh: Investigation of Anodes for Production of Electrolytic Zinc. Trans. A. I. M. E. (1930) 275

Jan 1, 1931

By W. L. Saunders

WHEN work was begun in September, 1910, on the rock excavation for the foundation of the gigantic dam at Valhalla, N. Y., which is to convert Kensico lake into an important storage reservoir of the Catskill Aqueduct system, one of the first steps taken by the contractor, H. S. Kerbaugh, Inc., was the development of a quarry to supply the stone needed in the construction work.The importance of a bountiful supply of suitable rock in an accessible location is apparent when it is considered that nearly a million cubic yards of cyclopean masonry will be contained in the completed structure, not to mention dimension and facing stones, concrete blocks, and mass concrete. The dam structure will be over 1800 ft. long and about 170 ft. above the present river bed. However, for a distance of some 800 ft., it will be carried down to solid ledge rock, which will make the finished structure about 300 ft. in maximum height. It will be about 200 ft. thick at the base and directly beneath the coping it will be 28 ft. thick. This dam will raise the reservoir surface 110 ft. above old Kensico lake. The reservoir capacity will be 29,000,000,000 gal.-equal to New York's total needs for over two months. The contract price for this work is nearly $8,000,000 and is second only in amount to the cost, over $12,600,000, of the Ashokan Reservoir work. Fig. 1 is a view of the dam site.

Jan 2, 1914