Search Documents

By R. I. Jaffee, H. P. Nielsen

In recent years much attention has been given to high melting alloy systems. It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. Past Work Miillerl determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from I771 C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Miiller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and Jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at I000 C. Vines and WiseS report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. Materials The platinum powder used in this work was kindly supplied by the Research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio. It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HC1. The resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1949

By William P. Blake

Postscript to the paper read by Prof. William P. Blake at the Lake Superior meeting, September, 1904. POSTSCRIPT.*-Since the publication of my paper upon the blackening of the surface of rocks in desert regions, I have noted that similar views of the origin of superficial discoloration in the case of certain rocks from the Salt Lake basin of Utah have been expressed by Prof. George P. Merrill. In the pamphlet, he described the brown-coated weathered boulders from Tooele county, reaching the conclusion that the discoloration was due to the solution of the manganese and iron compounds 'in the interior of the boulder, while they were in the water, and the gradual bringing of this material to the surface through capillarity and its oxidation when exposed.

Mar 1, 1905

By F. W. Glaser

Iron-silicon alloys have had a great influence, in many ways, in modern industry. Silicon steels have been used almost exclusively for the construction of electrical machinery, but have also become an important material for structures which benefit by the high tensile and yield strengths of this material. In elaborating on the early history of work done on iron-silicon alloys, Greiner, Marsh and Stoughton1 went back as far as 1808, and pointed to Berzelius as the first producer of ferrosilicon. During the last twenty years some very important contributions in the form of studies of the iron-silicon system, as well as of the physical properties of these alloys, have been published. In consideration of the brit-tleness and poor machinability of alloys containing more than 5-6 pct Si, commercial interests have stimulated the research done on iron-silicon alloys, but mainly in the range of 0 to 6 pct Si. Yensen2 has shown the influence of im- purities, such as carbon, sulphur and phosphorus on the magnetic properties of 2, 4, and 6 pct Si alloys. Corson3 extended his investigation of physical properties to approximately 32 pct Si, and attributed the brittleness of the high-silicon material to the particular constitutional features of the alloys. Though mentioned earlier in the literature, the effect of nitrogen on crystal growth and magnetic permeability of iron-silicon alloys has been demonstrated recently by Morrill4 and Rostoker,5 respectively. In all the above quoted investigations, except that of Rostoker,5 sand or chill casting processes were employed for the preparation of samples. A major advantage of the powder metallurgy process is that it does away with time-consuming machining in many applications. The powder metal industry is always interested in pro- ducing a finished product employing a material which has presented considerably greater difficulties in manufacture by other methods. Steinit26 described preparation and testing of various Fe-Si alloys which were produced by the powder metallurgy process for the manufacture of armatures for small electric motors or generators. While Steinitz investigated alloys up to 6 pct Si, Rostoker5 went as high as 9 pct Si. The author7 previously discussed the diffusion of iron-silicon compacts containing 6 and 10 pct silicon. It is the object of this paper to study the progress of diffusion occurring in iron-silicon alloys by electrical resistivity measurements. All samples were prepared by pressing and sintering of compacts. Iron, silicon, and Fe-Si powders of various mesh size and compositions were employed to obtain test samples. It was assumed that complete diffusion had been obtained when the electrical resistivity reached a constant value characteristic for that particular alloy. To this end, electrical resistance measurements were used to follow the progress of alloying under various conditions.

Jan 1, 1950

Jan 1, 1967

Jan 1, 1967

By AIME AIME

M ALBERTSON is research engineer for the Shell Petroleum COT. He joined the Roxana Petroleum Corp. (later the Shell) in 1920, at Hanger, Texas, became district geologist at Shreveport, and after two years was transferred to the production department, where he has been for the past fifteen years. His jobs have ranged from a modest field engineer up to assistant production manager. During this time hc has successively resided in Texas, Louisiana, Missouri, Louisiana, Oklahoma, Missouri, Texas, The Hague (Holland), and Texas. II? the Yates Pool, Texas, in 1929, "Al" initiated' the tubing of wells under pressure to control gas-oil ratios, particularly at restricted rates of flow. This led to the compulsory tubing of all oil wells drilled in the State

Jan 1, 1937

By AIME AIME

THE CHAIRMAN of the fast growing Petroleum Division is not only a graduate of the University of California, but a third generation native son. After a few years spent in hard-rock geology, his professional efforts were transferred to the sedimentaries and to petroleum investigations, as a consulting geologist. For ten years these investigations covered the Rocky Mountain, Oklahoma, Texas, and eastern districts. After the war he returned to Casper, Wyo., as chief geologist for the Consolidated Royalty Oil and Western Exploration Companies. This employment afforded him the opportunity to study particularly the economic relationship between the lessor-lessee interests in development and production, a somewhat unusual type of petroleum specialization.

Jan 1, 1939

By Charles H. Foreman

IN JUNE 1921, the Sullivan &lining Co., owned jointly by the Bunker Hill and Sullivan Mining & Concentrating Co. and the Hecla Mining Co, started work on the development of the Star Mine. The development work contemplated called for a crosscut from the Hecla workings on the 2000 level to the Star ledge. The length of crosscut necessary to encounter the Star ledge was approximately 8900 ft. from the Hecla shaft. By using workings formerly made by the Hecla Mining Co., only about 8100 ft. of actual crosscutting was necessary. This crosscut has a direction of S 20° W and would have a tendency to crosscut any ledges in the intervening ground.

Jan 1, 1924

By A. Eilers

A number of the copper refineries in this country have lately separated some of the rarer metals from the slimes in the refinery tanks. One of these has furnished me the following table of recoveries from given amounts of blister. I publish this to show the proportions, to gold and silver and to each other, in which these rarer metals may be expected to occur in copper from certain localities. GarFIeld, Utah :—The blister copper comes principally from the Bingham porphyry copper mines. Steptoe, Nev. :—All the blister copper is produced from the Nevada Consolidated mines. (Also porphyry deposits.) Omaha, Neb. :—Blister copper comes principally from concentrated copper-lead mattes shipped from the different lead-silver plants of the Rocky Mountain region to the converters at the Omaha lead refinery. Mountain, Cal. :—Ores occur in connection with diorite (?).

Jan 1, 1914

By George H. K. Schenck, Peter G. Donald

There is an accelerating acceptance of change by management of cement companies. Diversity of response is noticeable in efforts across the country to reverse the downward trend in profits that brought margins in 1966 to the lowest point in 20 years. New concepts are emerging among managers as they seek to increase the efficiency in use of the basic corporate resources of men, capital and technology. The shift towards computerized control of cement manufacturing is making new gains as is diversification of cement companies into allied fields such as production and sale of natural and light- weight aggregates, crushed stone and concrete products. Increased interest in special products such as white cement and further moves overseas are also significant. Perhaps the most dramatic event of recent years occurred in Washington at hearings before the Federal Trade Commission where cement producers split on whether there should be FTC guidelines that would prevent ownership of ready-mixed concrete producers by cement companies.

Jan 4, 1967

By M. M. Neale

The pottery department has been aptly described as the "heart of the zinc plant," md every operator of a horizontal-retort plant is acquainted with the fact that good retort practice is the keystone of the smelting process. Since retorts and condensers are clay products, it is obvious that improvements in other branches of the ceramic industry should be observed for possible adoption in the pottery process for zinc smelting. Deaeration of clay bodies is one of the improvements that have become fully, established in many brick and pottery plants. Our investigation of a number of these installations always yielded the same answer—improved practice. Improvement in workability, elimination of laminations, less porosity, greater wet and dry strength, were among the claims put forth for this process. All of these features are exceedingly desirable characteristics in the manufacture of a zinc retort. A preliminary test, which involved truck transportation of deaired slugs over a relatively long distance, did show the value of many of these characteristics in forming the retort. Results from the standpoint of , longer retort life in the smelting furnace were not outstanding. The idea lay dormant for several years but was revived again in 1940, when it was decided to make whatever changes were necessary in the equipment for pottery manufacture to fully demonstrate the process. A number of the manu- facturers of machinery for clay work were asked to submit proposals, and the plan finally adopted was extremely simple and economical. Machine FOR DeaeRRATING Selection of the ''Straight-line'' principle for conversion of the "Wettengel" pug mill to a ''vacuum-extrusion" machine preserved some usable parts of the original equipment, such as the drive mechanism, and main shaft. The converted machine consists of a feed hopper, a compression and shredding zone, a vacuum chamber, and an extrusion barrel, as shown in Fig. I. In operation the clay mix travels from the feed hopper into the compression zone, where it is compressed and finally forced around the tapered cone into the vacuum chamber. As it enters this chamber the clay body is shredded into thin plates, for exFosure to the vacuum. The shredder consists of a hub mounted on the main shaft, to which are bolted segmental sections, each of which carries shredder knives. The compression zone and extrusion barrel function as seals for the vacuum chamber and the shredded clay mix is agitated thoroughly during its exposure to the vacuum. A vacuum pump, equipped with a 3-hp. motor, is attached to this chamber, and maintains 25 to 26 in. vacuum during operation of the mill. Changes in Practice Prior to the adoption of the deaeration process, our standard pottery practice called for double mixing in the combination 7

Jan 1, 1944

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. PERCY E. BARBOUR, Vice-Chairman. A. D. BEERS, Secretary, 55 Wall St., New York, N. Y. C. A. BOHN, Treasurer. Boston Meets first Monday of each winter month. W. E. C. EUSTIS, Chairman. - R. L. AGASSIZ, Vice-Chairman E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston, Mass. ALBERT SAUVEUR, H. L. SMYTH. Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON, Chairman. FREDERIC KEFFER, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. D. C. LIVINGSTON. FRANK A. ROSS.

Jan 12, 1916

By Evan Evans

HOME-TOWN boy makes good in a i1 big way in the home ' town, expresses concisely the accomplishments of Evan Evans. Born in Coaldale, Pa., in 1895, within sight of the mine head-frames and cleaning plants dotting the Panther Creek Valley, his whole life has been intimately associated with the strip and underground mines of this valley. One of the world's largest mineral deposits exists in the confines of the Panther Creek Valley and mining has been in progress for 125 years. Despite this long period of mining activity, two thirds of the coal in the valley yet remains to be mined. The Lehigh Navigation Coal Co. is the operating company.

Jan 1, 1947

By H. S. Munroe

The dressing-works of the St. Joseph Lead Company were destroyed by fire, February 26th, 1883. Within about four months, or on July 5th, 1883, the new mill, with a capacity of 500 tons per day, was built and in active operation. The capacity of the new mill has since been increased to 800 tons per day. The old mill was built in 1867, by Mr. C. B. Parsons, the present superintendent. It was a curious rambling old structure, which had grown with the demands of the business; a few jigs having been added in one place, a table or two in another and wings and sheds added to the main buildings, from time to time, as it was found necessary to increase the efficiency or the capacity of the mill. The old mill was, moreover, a most interesting place to the student, a perfect "museum of ore-dressing." Nearly every form of dressing apparatus known to the art had, at one time or another, found a place under its roof, jigs of many kinds, concave, convex, side-bump and stationary tables, tyes, buddles, dolly-tubs, etc., etc. The method of dressing followed in the main the lines of English practice, but with many modifications, both in the machinery and the methods of working, due to the inventive genius of Mr. Parsons. Different forms of crushing apparatus were tried, and the best method of handling the ore and the different products of

Jan 1, 1889

By R. H. Lynn, T. C. Craig

During the year 1933, in the Texas Panhandle, 113 oil wells were completed, adding 33,337 bbl. to the daily potential of the field. The field potential on Jan. 1, 1933, as determined by the Texas Railroad Commission, was 149,260 bbl., with a daily allowable production of 41,000 bbl. The potential was raised gradually, until on July 16, 1933, it reached 155,344 bbl. with a daily allowable of 55,000 bbl. This potential and allowable was maintained over a period from July 16, 1933, to Sept. 8, 1933, when the potential was reduced to 136,893, with a daily allowable of 43,727 bbl. Since Sept. 8, 1933, there has been a gradual increase, until on Jan. 1, 1934, the field potential reached 159,740 bbl. with a daily allowable of 42,000 bbl. Of this amount 26,429 bbl. arc "marginal oil" and 2682 bbl. are exempt on account of water. Deepening of Wells During the year 64 wells were deepened, increasing their total oil production 9631 bbl. per day. Of this amount the Gray County granite wash contributed 9256 bbl. from 57 wells. It has been found in many places that the granite wash carries an additional oil pay from 50 to 75 ft. below sea level. The majority of the wells that were .drilled during the early development in Gray County encountered their oil above sea level. When the wells producing from the upper horizon have become unprofit-

Jan 1, 1934

By AIME

D R. GILLSON, who was born in Evanston, Ill., in 1895, is another one of those geologists who received his early inspiration and foundation in his science from that great teacher at Northwestern University, the late Professor U. S. Grant, and then went on to give his time and interest to Institute affairs-like those other Northwestern men, Arthur Blair, Gilbert Cady, Charlie Behre, Evan Just, Ian Campbell, Clayton Ball, and many others. After serving in the Navy in the first World War as, of all things for a geologist, a commissary officer on a transport, he went on to MIT and took his doctor's degree under Waldemar Lindgren in 1923. He even assisted in mineralogy at Harvard and thus had training under another great teacher, Charles Palache. He taught mineralogy and petrography at MIT from 1923 to 1928. After several summers of field work as an assistant in the U. S. Geological Survey, Dr. Gillson joined the staff of the du Pont company.

Jan 1, 1947

The resin-in-pulp (RIP) ion exchange process was originally conceived by the Atomic Energy Commission in the early 1950's. However it was developed to commercial success by the Anaconda Co. at its 3000-tpd ore processing mill in Grants, N. M. Essentially, the Anaconda mill's crushing, grinding and acid leaching operations are the same as at the nearby Kerr-McGee mill, except that Anaconda uses manganese dioxide instead of sodium chlorate as oxidant during acid leaching. The real differences between the two mills become evident when considering how Anaconda treats its leached materials.

Jan 8, 1974

Thomas H. Beddall, so we are informed by Major J. B. Carlock, has been promoted and is now Adjutant of the 1st Battalion, 1st Gas Regi¬ ment. He was awarded, last summer, the Croix de Guerre. R. A. Bull. See letter in Proceedings of Milwaukee Meeting. Captain Stanley C. Bullock's record since entering the service is given as follows in a letter recently received from Mrs. Bullock: Resigned position of mine manager in Chile in November, 1915, to return to England to obtain commission in Royal Engineers. Joined Officers' Training Corps, Dec. 20, 1915. Commission gazetted, Jan. 27, 1916, 2d Lieut., R. E. Landed in France, Feb. 6, 1916. Posted to 179th Tunnelling Co., R. E. Took part in following battles: Somme, 1916; Ypres;1917; Arras, 1917; Somme, March and July, 1917; Messines, 1917. Gazetted: Acting Captain, July 11, 1916; Temp.-Lieutenant, Oct. 26, 1916; Captain, Sept. 29, 1918. Awarded Military Cross, Jan. 1, 1918, for conspicuous bravery and devotion to duty under a heavy enemy gas bombardment, when, by his example and perseverance in spite of every difficulty and obstacle, mining work was successfully completed which was vital for the success of the operations. The Cross was presented to Capt. Bullock by the King, on Sept. 25, 1918. First Lieut. J. J. Cadot, in a letter sent to Mr. H. `V. Hardinge from France, says he has been at the "Front." He also mentions that the Boche "is a good sprinter."

Jan 12, 1918

By Philip Kraft

WHEN it came time to write a biography of Philip Kraft, we got out a copy of Bartlett's "Familiar Quotations" and looked through the references to Travel, Traveled, Traveler, and Traveling, feeling sure there would be some reference to Mr. Kraft. Sure enough, we found: "Travel, in the younger sort, is a part of education; in the elder, a part of experience." Had Francis Bacon done his writing three and a half centuries later, Mr. Kraft might well have served as the inspiration for that sentence. New Yorker born, he received his B.S. and E. M. degrees from Columbia. In 1912, then 22 years old, he took off for Germany where he spent two years studying at the Royal School of Mines, Berlin, for his Doctor of Engineering degree. Contrary to the Greeley-Soule precept, Mr. Kraft, on his return from Europe, went north to South Porcupine. Ont., working as geologist and mining engineer for the Dome Mine. From South Porcupine his next stop was Washington, D. C., where, during the years the country was in the first World War, he was engaged in war work.

Jan 1, 1947

Prof. Henry M. Howe, New York, N. Y. (communication to the Secretary*):—The results presented in Mr. Mathewson's paper are of very great interest. Perhaps the most interesting is that shown in Table I. and Fig. 1, in which the arsenic decreases in 10 min. from 0.22 to 0.07 per cent. This is such a large decrease that it is to be hoped that Mr. Mathewson will verify it by repeating his tests with a matte of similar composition. This is particularly to be desired, because the simultaneous removal of sulphur appears to be very small. All three blows further agree in showing that the removal of arsenic is in the very early part of the blow. The fact that the removal of arsenic then ceases abruptly cannot be explained completely by the fact that the arsenic has fallen so low as by its lowness to resist further removal, because in the first blow the arsenic becomes stationary at 0.06 per cent., whereas in the third blow it does not become stationary until it has fallen to 0.034 per cent. The abrupt ending of the removal of arsenic is more likely to find its explanation in the composition of the slag, and it is to be hoped that Mr. Mathewson will supplement these extremely valuable data with others in which the composition of the slag at the same time shall be given. The sudden rise of arsenic toward the end of the third blow I suppose must be referred to an error in sampling or analysis.

Jan 1, 1908