Search Documents

By Oliver Bowles

WAR necessities have spurred inventive genius in many fields. A grinding mill without any moving grinding parts stirs the imagination. Among the new and striking accomplishments in the heterogeneous group of nonmetallic industrial minerals is the use of an electric arc to speed up manyfold the difficult and delicate task of drilling a microscopic hole in a diamond, the hardest of all known substances. Outstanding in the field of optical research is the ability that man has developed to improve upon nature by making in the laboratory optical crystals many times larger than those usually found in rocky crevices. These are merely samples of numerous events and circumstances of noteworthy import, many of which are recorded in this review. Termination of the second World War in 1945 permits an appraisal of the effects of the conflict and the probable effects of the coming restoration of a peacetime economy on the nonmetallic mineral industries. Some industries were stimulated greatly by the war, notably mica, quartz crystal, graphite, spinning asbestos, potash, fluorspar, barite, and refractories. The large-tonnage industries connected with the building trades, however, were forced to curtail their activities, except where their products were needed for wartime construction. Their reconversion to peacetime production will not be difficult.

Jan 1, 1946

By Fred D. Wright, Philip B. Bucky

FOREWORD By E. D. Gardner[$] THE present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems. INTRODUCTION The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.1 As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining cost. It was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1947

Jan 1, 1967

By R. E. Ray, J. W. Stevenson, J. A. Berry

Conventional concrete block plastered with a cementitious coating is the most common material used in the construction of permanent stoppings to direct airflow in underground mines in the US. All mines experience various degrees of strata convergence depending on depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting insignificant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating a polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1986

By William B. Hughes

The rubber-sleeve core barrel was developed to improve core recovery from unconsolidated sands, where it is most difficult to obtain cores with conventional barrels. The use of a rubber-sleeve core retainer, together with other departures from clsual design, has required a considerable amount of testing to prove its op-erability. Tests run in shallow experimental holes and in drilling wells in the U. S. and Vemzuela have, to a large extent, proved the operation of the barrel. Internal mechanism troubles, such as sandbinding of the sleeve, have been largely overcome. Cores have been recovered from completely unconsolidated sands where conventional coring has almost been abandoned because of poor recovery. In addition to retaining the core until brought to the surface, the barrel gives a "packaged-ar-cut" core, which is coilverzient for handling and transportatiorz. In the initial work, drag blade cutters, roller cutters, and tungsten carbide insert cutters were usrd for cutting unconsolidated sands. Further bit head development is presently being conducted using diamond heads in unconsolidated sands where shaler, hard sands, and limestones are encountered in adjacent formations. Thir work should render the barrel capable of cratting and recovering most types of formations, possibly including broken and frac- tured fornlations. This development is being carried on in cooperation with a diamond bit manufacturer. INTRODUCTIO N For many years the oil industry has needed greater recovery of cores from unconsolidated formations. Conventional equipment has been used to core unconsolidated sands with little success. Specifically, a core barrel was needed which would recover unconsolidated sands in a condition that would give useful reservoir information. DEVELOPMENT OF 'THE RUBBER-SLEEVE CORE BARREL Basic Requirements of Unconsolidated Sand Corino The basic need was defined as a core barrel that would obtain a continuous unconsolidated core with sand grains in place as deposited in the formation. A preliminary survey of coring equipment and search of the literature pointed out the weaknesses of conventional core barrels. Laboratory tests using unconsolidated sand in a metal tube simulated actual sand movement into the core barrel during conventional coring. In conventional barrels the core sometimes crumbles and bridges, or fails under compressive column action, becomes oversize, and wedges against the walls of the inner barrel. The core barrel requirements established by the surveys and preliminary tests are as follows. 1. The core should be held to- gether as it is cut so it cannot crumble and bridge against the walls of the coring tool, care being taken not to permit damage from fluid circulation. 2. The core should be continuously supported as it is cut so it will not have to support itself in compression. 3. The core should be packaged in the barrel to retain an undisturbed condition during the trip out of the well. The packaging should be such that the core can be removed from the barrel and shipped to the core analysis laboratory without physical disturbance or alteration of fluid content by exposure to the atmosphere. Operation of the Rubber-Sleeve Core Barrel The rubber-sleeve core barrel (Fig. 1) meets the basic requirements for the recovery of unconsolidated sands.

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man's' solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

By Charles R. Fettke

In connection with the gathering of data for a report on the geology of the Humacao district of southeastern Porto Rico during the summer of 1916, under the auspices of the Scientific Survey of Porto Rico and the Virgin Islands, conducted by the New York Academy of Sciences, the writer had an opportunity to make a brief examination of the magnetite deposits of the eastern portion of the island. Inasmuch as these deposits have attracted some attention as possible future sources of iron ore, and as there is only scanty reference made to them in literature,' a short description based on this reconnaissance survey was deemed to be worthy of record. The magnetite deposits of eastern Porto Rico occur in association with a belt of limestone, trending approximately S 53° E, which begins 11/2 miles east of Juncos and can be traced for about 6 miles toward the coast. Four outcrops of magnetite were observed, which are designated as Nos. 1, 2, 3, and 4, respectively, on the map shown in Fig. 1. Others are probably present, but escaped notice on account of the thick mantle

Jan 1, 1924

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today's miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What's the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961

By R. A. Bosch, F. V. Lenel, G. S. Ansell

RECENTLY, Ansell and aenel' proposed a dislocation model to account for the yielding behavior of dispersion-strengthened alloys. The criterion for yielding used in this model was that yielding occurs when the shear stress due to arrays of piled-up dislocations fractures or plastically deforms the dispersed second-phase particles. Calculations based on this model predict that the yield strength, uysof a dispersion-strengthened alloy containing particles whose geometry permits them to be considered as straight, i.e. not curved, barriers to dislocations follows the relation where and are the shear moduli of the matrix and dispersed phase respectively, b is the Burger vector of a dislocation in the matrix, A is the mean free path between dispersed phase particles and C is a constant. This yield stress, ys, is closely approximated in polycrystalline alloys by the proportional limit. The offset yield stress, uoy, is the yield stress, uys, plus the increase of stress due to strain hardening in the offset strain increment. Previous investigation1 has shown that Eq. [I] describes the yielding behavior of several different dispersion-strengthened alloys as a function of the mean free path between dispersed phase particles at a constant temperature. The purpose of this investigation was to investigate the temperature dependence of the yielding behavior of dispersion-strengthened alloys. The alloys studied, MD2100 and MD5100, are SAP-type alloys containing flake shaped aluminum oxide particles dispersed in a matrix of commercial purity aluminum. The proportional limit and 0.2 pct offset stress of both of these alloys were determined as a function of temperature over the temperature range from -190" to 500 C. All tests were conducted on an Instron tensile testing machine. Stress was measured by means of the Instron load cell. Strain was measured by means of SR-4 strain gages attached to the tensile specimens. Stress sensitivity was 80 psi. Strain sensitivity was 2 x 10F Fig. 1 shows the values received for the proportional limit and 0.2 pct offset yield stress plotted as a function of homologous temperature for both the MD2100 and MD5100 alloys. Inspection of Eq. [I] shows that of the terms which determine the theoretically predicted yield stress, uy,, only the shear moduli have an appreciable temperature dependence. From Eq. [I] the yield stress at any temperature T, UT, may be predicted from the yield stress at any arbitrary reference temperature, in this case 25 OC, u25, by the relation where the subscripts T and 25 refer to the values of the property at test temperature and at 25"C, respectively. The temperature dependence of the yield stress predicted by Eq. 121, based on the observed value for the proportional limit at 25OC, is also shown in Fig. 1. In evaluating Eq. [2] the following data was used. The values for the shear modulus of

Jan 1, 1962

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By C. A. Allen

For over three years we have been endeavoring to reduce the number of fatalitics and minor accidents in Utah. The physical condition of the FIG: 1.—Number kiLlEd per million short tons of coal produced in ColoraI)o, New Mexico, utah, Wyoming, and bituminous mines of the United States 1014 to 1920. mines, concentrators, and smelters is good, yet the number of accidents,

Jan 1, 1923

By A. E. Anderson, H. J. Hilll

Laboratory data for 155 field muds and 77 .shales have been used to develop correlations to estimate the net streaming potential component of the SP. Analysis of these data and comparison with field tests show that streaming potential corrections must be made to obtain an accurate estimate of the electrochemical potential for use in the determinntion of formation water resi-iiviy. The self-potential curve is related to formation water resistivity, and considerable effort within the oil industry has been directed toward clarifying this relationship. The Schlumbergers and Leonardon1,2 recognized that two types of potentials, electrochemical and electro-kinetic, resulted in the net potential variation in the borehole. Most of the later papers have dealt with the electrochemical component and its controlling parameters. The investigations of Wyllie,2" Salisch' and Moore5 provide the most extensive sources of data on streaming potentials across mud cakes. These authors observed streaming potentials of sufficient magnitude to be of critical importance in SP interpretation, if it is assumed that streaming potentials develop only opposite permeable beds. Streaming potentials across shales have been reported by Schenck and by Gondouin, et al.7 Since SP magnitude is the difference in potential opposite shale and sand beds, these authors suggested that the net streaming potential component may be negligible. The present investigation was initiated to evaluate empirically some of the parameters controlling the magnitude of the net borehole streaming potential and to determine whether useful relations between mud properties and net streaming potential could be established. Field muds were used in this investigation. These muds were characterized by the amount and type of chemical treatment utilized for five days before Sampling. Filter loss, mud resistivity, mud density and filtrate resistivity were determined for each mud with conventional methods and apparatus. Mud filtrate pH was estimated with Hydrion pH paper for the appropriate range. Streaming PotentIals Across MuD Cakes Commercial calomel-saturated KC1 electrodes are subject to potential changes attributed to contamination of the very small fiber-tip bridge by particles of clay from the drilling mud.3 To minimize this difficulty, a large diameter bridge (Fig. 1) was constructed with saturated KC1-agar gel and a filter disc of microporous porcelain. Experiments showed that streaming potentials across this bridge are less than 0.2 mv at pressure dif-

By Benjamin Smith Lyman

THE importance of topography to geology is so commonly underrated as to deserve to be pointed out again and again. The relation of topography to the different branches of geology may be seen best by a glance at them all. Geology is well understood to consist of the observation of facts about rocks as materials of the earth (geognosy), and the explanation of those facts (geognosy). The facts to observe are : I. GEOMETRICAL, as (1) structure, including the dip and strike at different points, the size, shape, and position of basins and saddles; (2) vertical section, that is, the thickness of rock groups and of their parts ; (3) horizontal or geographical position. 11. PHYSICAL, such as texture, whether sedimentary or crystalline ; and, if crystalline, whether granitic, porphyritic, amygdaloidal, globular, or concretionary ; whether compact or granular; coarse or fine; pervious or impervious; hard or soft; firm or tender; with cleavage or without ; massive or thin ; the microscopic structure ; also whether magnetic or not ; soluble or insoluble ; fusible or infusible ; and the constituent minerals. 111. CHEMICAL that is, the composition of the rocks and of their minerals and their affinities. IV. PALAENTOLOGICAL, as what kind of fossils are in the rocks,

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46" 31' north latitude, 67" 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sul-fide deposits of the Bathurst-Newcastle district. The helicopter electromagnetic equipment located an anomalous conductive area, coincident with a small aeromagnetic closure, about five miles west of the town of Juniper. Subsequently 30 mining claims (total area about 6600 x 8000 ft) were staked and company personnel conducted geological, geophysical, and geochemical investigations on the property. The claims and immediately contiguous areas were mapped geologically, and an area of about 2000 x 4000 ft was soil-sampled and also surveyed by ground electromagnetic and gravity methods. Finally six diamond drillholes, totaling 3500 ft in length, were drilled to test the anomalous conditions discovered by the several exploration techniques used. The discovery of base metal sulfides during drilling was a technical success for the exploration methods, but the quantity of sulfides was too small to be profitably exploited.

Jan 1, 1959

By Stanislaus Skowronski

OVERPOLED copper, as commonly defined, is copper which has been excessively reduced during the poling period of the refining process. Owing to its porosity, such copper is unfit for commercial purposes. The cause of this phenomenon is undoubtedly the lack of oxides in the copper, yet this does not completely explain it. Refined copper of the same "pitch" and "set" varies considerably in oxygen contents, and analyses of overpoled bars also show similar wide differences; moreover, it is possible to melt copper in crucibles so as to obtain bars that are practically free from oxygen although they show a "tough pitch" and "level set" surface. Frederick Johnson advances the following theory: The regulation of the quantity of oxygen in copper is the keynote of all copper refining. It is the presence of a Well defined proportion of oxygen in the form of cuprous oxide, forming a copper-cuprous oxide eutectic, Which enables copper to be cast free from blowholes. It seems that When oxygen is present, other gases are less soluble in molten copper; When oxygen is absent, or is present in insufficient quantity, the copper dissolves other gases, such as hydrogen and carbon monoxide, Which are insoluble in the copper when solid, and, being rejected during the process of solidification, causes internal porosity and external ridges and excrescences.1 The "level set" of Wire bars, etc., is entirely the result of a compromise between the occluded gases and cuprous oxide. With excess of the former the metal would be "overpitch" and spongy, While an excess of the latter would result in the metal being "underpitch" and brittle.2 The result of the absorption and subsequent expulsion of reducing gases, carbon monoxide and hydrogen, and the effect of this action. on the overpoling of copper are in dispute; the literature on the subject is full of contradictory statements and will continue to be so until better analytical methods have been developed. Sulphur, however, is tangible. The refiner can see it in his button sample and consequently attributes to it any trouble that may happen during the melting of the copper.

Jan 3, 1918

By Richard Miller

RECENT studies of creep have made it apparent that plastic deforma-tion may occur in metals under stresses less than the elastic limit as deter-mined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapsell1 said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a. definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was deter-mined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instru-ments by A. W. Hanson4 on zinc and by Podaschowsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc.

Jan 1, 1936

By A. W. Schlechten, W. J. Kroll

As this paper is written, the only method for the commercial production of lithium metal is by the fusion electrolysis of LiC1-KC1 mixtures, as first proposed by Gunkz.2 The details of the industrial process have not been made public hut Osborg8 stated that an efficiency of more than 90 pct is obtained with a lithium metal recovery above 95 pct and that the metal is 99.5 pct pure. Pletenev9 gave a power consumption of 66 kw-hr per kilogram of lithium metal produced with a salt consumption of 9 kg of LiCl and 0.4 kg of KCI. Pletenev's figures indicate a somewhat lower recovery than that given by Osborg. In a recent report on' German lithium plants, Motock7 gives figures that are also less favorable than those reported by Osborg. At the German plants the lithium recovery in electrolysis was only 83.4 pct, with a power consumption of 140 kw-hr per kilogram of lithium. The metal averaged only 97 pct pure, with sodium and potassium as the chief impurities. The presence of SO2, SO3, SiO2, Ba, Ca, and appreciable amounts of Na and Fe2O3 were especially disturbing in the electrolysis, and it was necessary to run the cell for some time to eliminate most of these impurities and condition the bath. It may be noted here that most of these impurities do not interfere with a thermal reduction process. These facts show that the present method of producing lithium is fairly efficient and would suggest that other methods could not compete. However, fusion electrolysis has certain drawbacks, such as the necessity of supplying costly, low-voltage direct current and of collecting and processing the anodic chlorine if it is not to be wasted. An even greater disadvantage is that lithium chloride must be used for an electrolyte. It is one of the most expensive salts of lithium, since it cannot be produced in anhydrous form by precipitation from aqueous solution, as is done with LiF or Li2CO3. The reduction of lithium by a vacuum process similar to the ferrosilicon method for the production of magnesium would have certain advantages. Small units such as Pidgeon retorts, would give flexibility of production to meet demand, and a small plant would require moderate capital outlay. There is a possibility of using idle Government-owned magnesium plants for such purposes. The raw materials needed for vacuum thermal reduction would not have to be extremely pure, Director, with respect to the iron and calcium Content. This paper describes a series of experiments to determine the effectiveness of various agents for the reduction of lithium compounds. The investigation is part of a program of vacuum metallurgy con-

Jan 1, 1949

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

Jan 1, 1971

By N. A. D. Parlee, I. D. Shah, W. C. Phelps

THIS note reports on a continuation of a program on the thermodynamics of Fe-S-X systems in the "steel-burning" temperature range begun by Bock, Barloga, and parlee.' Small coils of 0.039-in.-diameter pure iron (Ferrovac-E) wire were equilibrated with Fe-S-0 melts in ingot iron crucibles under argon at 1324°C in the assembly shown in Fig. 1, the lower part of which was heated in a large Globar furnace. Fig. 1 shows (R) the coiled iron wire sample, (M) the Fe-S-0 melt prepared from desired proportions of ferrous sulfide and ferric oxide, (K) the iron crucible, (I) a mullite guide tube, (J) an alumina crucible, (L) alundum sand, (N) crushed mullite, (Q) hollow cylinders of K30 brick, (C) a steel rod, (B), (El, (F), (G), (P), and (O), details of brass water-cooled head, and (H) a mullite tube 2-3/4 in. ID and 26 in. long. The rod (C) bearing the sample could be removed at will and be replaced by a tube for sampling the melt, or by a thermocouple for comparing the melt temperature with a control thermocouple not far from the 2-3/4-in. mullite tube. After equilibration the iron coils were treated with acid to remove the outer layer of metal and then they were analyzed for sulfur by a standard combustion method. The melt samples were analyzed for oxygen by a variation of Lander's2 hydrogen-reduction method for mattes, and for sulfur by the ASTM combustion-iodometric method NO. E 30-47. When the results of some forty-two runs were examined it was found that the sulfur and oxygen contents of the equilibrated melts showed good consistency, in that the plotted compositions fell along the smooth curve shown in Fig. 2. The points on this curve represent the experimental compositions of melts in equilibrium with ?-iron (Fe-S-0) solid solutions. These solid solutions are saturated with sulfur and oxygen with respect to the melt and therefore have the same sulfur and oxygen activities as the melt. The curve drawn through the points therefore delineates the ? liquidus. It falls in such a position as to roughly confirm the liquidus curves of Hilty and crafts3 at 1200" and 1300°C which are

Jan 1, 1965