Search Documents

By Che, C. W. Spencer, C. A. Steidel, Yu Li

Grain boundary grooving as it occurs in a 5.5-deg simple-tilt nickel bicrystal immersed in a saturated Ni-S liquid has been studied. A 1/3 (t= time) dependence for the depth of the groove indicates that the rate -controlling meckanism for groove developvnent is volume diffusion in the liquid. The activation energy for the diffusive process is estimated at 15 kcal per mole. Using an extended form of W. W. Mullins&apos; analysis for grooving reactions, a computer is employed to fit the appropriate diffusion equation by a numerical method. From the analysis a possible method of measuring L.S. the solid-liquid interfacial tension is demonstrated. WHEN a polycrystalline solid is heated in equilibrium with a saturated fluid phase, grooves will form at the intersections of the grain boundaries and surface. The equilibrium root angle of these grooves is determined by the balance between the grain boundary and solid-fluid interfacial tensions. The grooves deepen and widen with time due to a difference in chemical potential between the flat interface and the curved interface of the groove. In this investigation solid-liquid interaction at a grain boundary is studied, with the object to determine the mechanism of grain boundary grooving in the presence of a saturated liquid. Extension of Mullin analysis then permits the estimation of the solid-liquid interfacial tension. Herring has demonstrated by dimensional analysis that the quasi-steady state change of the dimensions of a small particle during sintering is proportional flow, evaporation-condensation, volume-diffusion, and surface-diffusion mechanisms, respectively, if geometric similarity of consecutive configurations of the particles holds. Mullins has extended this analysis to grain boundary grooving. In the case of shallow grooves he solves the diffusion equations for evaporation-condensation, volume-diffusion, and surface-diffusion mechanisms, and obtains the same time dependence for any linear dimension of a groove as Herring found for the change in dimension of small particles. In Mullins&apos; analysis2&apos;3 grain boundary grooving of a bicrystal by volume diffusion in the presence of a saturated fluid phase was considered. Several assumptions were made prior to the analysis: 1) the solid-fluid interfacial tension is independent of crystallographic orientation; 2) the Gibbs-Thompson equation relating curvature and chemical potential is applicable at the solid-fluid interface; 3) the relaxation time of the diffusion field is small compared with the time for appreciable changes in the curvature of the groove, so that the diffusion is divergence-less; and 4) the groove has a small slope relative to the initial flat interface. Usually this last condition is fulfilled only for solid-gas systems. The solution of the diffusion equation under the above conditions produces a t1/3 dependence for any linear dimension of the groove in the case where volume diffusion is rate-controlling. The t1/3 dependence is valid because geometric similarity of the grooves exists for all time. EXPERIMENT In the experiment a 5.5-deg nickel bicrystal of <100> simple-tilt orientation was used.4 Grooving was studied in the presence of a saturated Ni-S liquid alloy as a function of time at 750°, 800°, 850°, and 900°C. A low-angle bicrystal was chosen for study to insure that 2L.S. > .b., where l.s.

Jan 1, 1964

By Alec M. Crowell, C. H. Thigpen

Continuing the increase in production of crude oil and condensate started in 1937, the oil fields of South Arkansas reached a 13-year peak with 26,570,704 bbl. for the year 1942. The stability of the production branch of the industry in the area is demonstrated by Fig. I, which reflects the fact that although the number of producing wells in the state has declined from 3280 in 1931 to 2957 at the end of 1942, total production has continuously increased since the beginning of 1937. This is because all fields discovered since Jan. I, 1937, have observed spacing patterns up to one well to each 160 surface acres, the dual completion of wells where there is more than one producing horizon Eight new pools were brought into production in South Arkansas during 1942 (Fig. 2) They increased the state&apos;s crude oil and condensate reserve by 121,000,000 bbl., bringing the total recoverable reserve figure to 450,000,000 bbl. (Table 3) as of Jan. I, 1943. Abandonment of wells in the stripper areas of the state increased by 32 per cent over the preceding year, there having been 142 wells permanently abandoned in 1942. For economic reasons 279 wells were temporarily shut down as of Dec. 31, 1942. A price increase may start these wells to pumping again and also be the incentive toward the commencing of several secondary recovery projects in the fields discovered between 1922 and 1937. There were 149 wells brought into production in 1942 as against 119 for the

Jan 1, 1943

By C. H. Thigpen, Alec M. Crowell

Continuing the increase in production of crude oil and condensate started in 1937, the oil fields of South Arkansas reached a 13-year peak with 26,570,704 bbl. for the year 1942. The stability of the production branch of the industry in the area is demonstrated by Fig. I, which reflects the fact that although the number of producing wells in the state has declined from 3280 in 1931 to 2957 at the end of 1942, total production has continuously increased since the beginning of 1937. This is because all fields discovered since Jan. I, 1937, have observed spacing patterns up to one well to each 160 surface acres, the dual completion of wells where there is more than one producing horizon Eight new pools were brought into production in South Arkansas during 1942 (Fig. 2) They increased the state&apos;s crude oil and condensate reserve by 121,000,000 bbl., bringing the total recoverable reserve figure to 450,000,000 bbl. (Table 3) as of Jan. I, 1943. Abandonment of wells in the stripper areas of the state increased by 32 per cent over the preceding year, there having been 142 wells permanently abandoned in 1942. For economic reasons 279 wells were temporarily shut down as of Dec. 31, 1942. A price increase may start these wells to pumping again and also be the incentive toward the commencing of several secondary recovery projects in the fields discovered between 1922 and 1937. There were 149 wells brought into production in 1942 as against 119 for the

Jan 1, 1943

By Eugene Grace

IN THE careers of the men to whom I have referred we find typified the development of the chief prob-lems of engineering. The first is to shape and direct the forces of nature and thus to bring the world&apos;s resources to add to the comfort and welfare of man-kind. That, in a word, is the problem of production. Engineers have made a supreme contribution to the solution of that problem. But I feel that we have two somewhat newer branches of engineering which must command more and more of our attention. Those are what might be termed commercial and human engineering. Of what value is all our efficiency in pro-duction if we do not distribute efficiently, economically and effectively? And of what value is any of it unless we can add to the happiness and deeper satisfaction of those engaged in industry, as well as those who enjoy its -products? I predict that the outstanding advances in business over the next ten years will be in improved merchan-dising and distributing methods. Herein lies a wide field of opportunity for the engineer. We have briefly reviewed certain qualities of engi-neers who have become successful business executives. Is it possible for us to say that the material success of all these men was due to any one characteristic com-mon to each one of them? Indeed, I venture to assert that there is one quality which, in the last analysis, is determining as to whether any roan shall realize material success in this world of ours. That quality-so notable in the character of each one of the men I have named-is sound judgment. Moments arise in every life when it is necessary to say "yes" or to say "no" to a particular proposition or to a proposed line of action. It is the man who says "yes" at the proper time and "no" at the proper time who, in the final analysis, realizes business success. The ability to do this wisely is the mark of sound judg-ment, which is necessary in a business executive. I have known many business men seemingly slow in their mental processes, possessed apparently, of little imagination and of none of the flair which gives fasci-nation to so many characters, and yet who, when crises come-be they big or be they little-are able so to steer their business courses that they move in the right direction instead of into shallow waters or upon the rocks of trouble.

Jan 4, 1928

By William Sellers

tested without knowing anything of their chemical composition. I had these pieces separately placed upon 10-inch bearings under a 7-gross ton lianlrner, a piece of 2½-inch round iron laid upon them as a fuller, and the hammer allotved to fall from 20 inches above the fuller, which, according to Haswell, gave a ldow of 67.75 gross tons. The pieces were then turned orcr, the fuller placed upon the convex surface, and the harnnler allowed to fall from 13 inches above the fuller, giving a blow of 58.46 gross tons. You will see that the rails do aot show ally bigrls of ruptnre, and their color at the points of torture prove them to have been absolutely cold when the test was made. I thirk these rails ought to be reasonably safe in the track. As you see by this piece of the head of one of these rails, I had it plarred, and then some teeth cut in it by a cold clrisel, and one-half of them pounded down with a hammer. The teeth of my rack did not break off. The analyses of these rails substquently made are: I. 11. Carbon,... 0.110 0.880 Silicon,..0.050 0.058 Phosphorus ,..0.086 0.082 Manganese,.. 0.042 0 840 In conclusion, I will say that Dr. Dudley&apos;s paper as a contribu tion to our knowledge of steel rails is valuable and interesting, but I protest against his conclusions king reoeived as manufacturing or comtnercial axioms. From its being presented in the form-of a report to the leading railroad of the country from one of its trusted officers, as well as from the tone of the concluding deductions, it is liable to be so received by railroad men. If any railroad com pany desires rails made under either of Dr. Dudley&apos;s formulas, and are willing to pay a price large enough to cover the loss in making them, dl and good; but so long as the rail makers are compelled to gwrrantee the wear of their rails for a given number of years, justice reqnires that. the composition of the steel from which these rails are made should be left to them. WILLIAM SELLERS, PHILADELPHIA: The very interesting paper upon the wear of steel rails that has just been read preseak the record of a series of investigations that are extreniely valuable, and the deduction that bas been drawn from the results noted seems to be unavoidable; the tests, however, to which it is proposed steel rails shall be subjected hereafter, with a view to determine their quality, sllould

Jan 1, 1881

By Arthur E. Focke

IF a metallurgist employed in an industry producing mechanical parts or assemblies wishes to make the most of his opportunities he will be concerned with every use of metals in that industry. He will not only take part in the testing and treating of the metals used but will assist in their selection and study their behavior in processing and in service. In addition, he will attempt to develop an understanding of the problems involved in the use of the metals in all plant tools and equipment. Metallurgists that follow this course will soon recognize that frequently too little thought is given to the effect of the design of parts on the way the metal in them is expected to behave in service. He will come to realize that changes in the design of a part will often be much more useful than changes in the hardness, strength, composition, or structure of the metals used in them. Does this mean that a metallurgist is out of place in these industries and that he should leave the field to others or be content to fill only a minor role?

Jan 1, 1947

By A. Keith Brewer

RECENT advances in the fields of chemistry, biology, and metallurgy have confronted the analytical chemist with an entirely new set of problems. Development of plastics and synthetics has brought about a need, not only for adequate methods for their analysis but also for the various raw materials entering into their manufacture. The remarkable advance made in biochemical and agricultural research resulting from the use of isotopes as tracers or "tagged atoms" has established the necessity for the development of methods for the concentration of natural isotopes and for a means for their analysis. Similarly the advent of new and complex alloys calls for accurate analytical methods. Fortunately the analytical chemist has been able to meet some of these new demands by adapting to his purposes an instrument which has long been the most exclusive toy of the physicists. Solubility and the chemical properties of the atoms, which have always served as the basis for chemical analysis, do not enter into this new technique. Instead, momentum, defined as mass times velocity, is utilized as the means for the separation of atoms or mass groups.

Jan 1, 1946

By M. Duclos, A. Sawatzky

A simple model has been developed which describes the steady-state solute distribution in Ti-H type systems above the eutectoid temperature in the presence of a temperature gradient. The solute distribution is dependent on the shape of the phase boundaries. An interesting result, and one that is not observed at steady state in thermal diffusion below the eutectoid temperature, is the existence of a two-phase region. The heat of transport for hydrogen in a titanium, Q*a, over the temperature range 275" to 650.C is determined to be 4500 * 230 cal per mole. The heat of transport for hydrogen in B titanium, QB* over the temperature range 320" to 590.C is found to be 630 ± 200 cal per mole. It is also shown that thermal diffusion provides a method by which phase bounduries above the eutectoid may be determined in Ti-H type systems. IN modern technology materials are being used at constantly increasing temperatures under greater temperature gradients. Thus atomic migration in metal alloys due to a temperature gradient (thermal diffusion) may in some cases occur to an observable extent. The thermal diffusion of hydrogen in zirconium has in recent years received considerable attention1-&apos; because of the use of zirconium alloys in nuclear power reactors. The thermal diffusion kinetics below the eutectoid (547°C) are fairly well understood. At steady state the solid solution, a, and hydride, 6, phases are completely separated with the hydride precipitating at the lower temperatures. No experimental work has been carried out in the a + B region although Droege4 suggested that a complete separation of the two phases, as observed at temperatures below the eutectoid, might not always occur. In the present investigation a simple model has been used to determine the steady-state solute distribution under a temperature gradient in Zr-H type systems heated above the eutectoid temperature. The solute distribution is shown to be dependent on the shape of the phase boundaries in the constitutional diagrams and several typical cases are discussed. The model has been applied to Ti-H. This system was chosen in preference to Zr-H because of its much lower eutectoid temperature (-300°C as compared with 547.C), thereby reducing experimental errors due to oxidation and hydriding. The heats of transport for hydrogen in the a and B phases of titanium also have been determined since they were required to compare the proposed thermal diffusion model with experiment. THEORY In the presence of a temperature gradient the atomic flux in a single-phase region of a two-com-ponent system of which the atoms of only one component are diffusing is given by:&apos; J = - U\dx + RT3 dx) which can be written as: j-D(dn/dt +Q*n/RT2)dt/dx [11 J - -D\dT + RT2)dx [1] where D = diffusion coefficient, n = solute concentration, T = absolute temperature, R = gas constant, dT/dx = temperature gradient, and Q* = heat of transport. At steady state (J = 0) Eq. [I] leads to the solute distribution: n = noexp Q*/RT where no = a constant depending on total solute content. The heat of transport Q* can be experimentally determined from the steady-state distribution. In the present paper we shall determine the solute distribution in systems having the constitutional diagram exemplified by Ti-H shown in Fig. l.&apos; As shown, N,(T) and NB(T) are the equilibrium solute concentrations in the a and 0 phases at temperature T. Lines AA&apos; and CC&apos; define the region of interest to us. The following assumptions are made: 1) Steady-state conditions prevail. 2) In a single-phase region all points on an isotherm have the same thermodynamic potential so that the composition over an isotherm is uniform. If a two-phase region exists, thermodynamic equilibrium is found only at phase interfaces. However, we assume the component of the concentration gradient along an isotherm to be small so that the composition in each phase is approximately the same as at the interface and is given by the constitutional diagram, Fig. 1. 3) There is appreciable diffusion of only one component. 4) We shall consider only the case where Qa*, QB*, and Qg*, the heats of transport for solute diffusion in the a, B, and 6 phases, respectively, are positive. This has been observed for the thermal diffusion of hydrogen in zirconium3 and titanium.10 We will show that the steady-state solute distribution above the eutectoid is primarily determined by the heats of transport and the temperature dependence of Na(T) and Np(T). It may be quite different from the steady-state distribution below the eutectoid. For example, we will see that, under certain conditions,

Jan 1, 1970

By JAMES SCULLY

For the last 4 years political leaders have found a new subject on which they can safely generalize wihout creating opposition. That subject is commodity prices. Since the four-fold increase in OPEC crude oil prices, public attention has focussed as never before on the subject of commodity prices. To advocate stabilizing commodity prices is akin to supporting motherhood or peace or better schooling. Everyone gives lip service to the concept that stable commodity prices are desirable. It is easier to state the principle than to achieve it. Prices that are stable in terms of one currency may be clearly unstable in terms of a different currency. This has become a troublesome matter since 1971, when the world&apos;s leading trading currencies were set free to float in relation to each other. To illustrate: consider copper prices in the interval between the end of 1974 and the end of 1977. During those 3 years, the copper price in pounds sterling on the London Metal Exchange rose by 25 per cent. During that period, however, in terms of the USA dollar equivalent, the price was unchanged. And during that period, in terms of the German mark equivalent the price shrank by 13 per cent while the Japanese yen equivalent fell by 20 per cent. Thus a price that appears stable in dollars, rose in terms of pounds sterling and fell in terms of marks and yen. Had this result been achieved as a consequence of an international effort to stabilize prices, an American would have said the effort was successful. An Englishman would have said it had failed to prevent a price rise. And a German or a Japanese consumer would have been happy to have covered his copper needs at a lower cost in terms of his own currency.

Jan 1, 1978

L50 Adirondack L1 Alaska L2 Arizona L58 Arkansas L66 Billings Petroleum L3 Black Hills L4 Boston L5 Carlsbad Potash L6 Central Appalachian L60 Central New Mexico L7 Chicago L8 Cleveland L9 Colorado L57 Colorado Plateau L10 Columbia LII Connecticut L55 Dallas L12 Delta L65 Denver Petroleum L13 Detroit L14 East Texas L15 El Paso Metals L71 Evangeline L45 Florida L54 Fort Worth L16 Gulf Coast L61 Hobbs L62 Hugoton L68 Illinois Pet Basin L17 Kansas L18 Lehigh Valley L52 Lou-Ark L47 Mexico L19 Mid-Continent L20 Minnesota L56 Mississippi L21 Montana L22 Nevada L64 Niagara Frontier L23 New York L67 New York Petroleum L25 North Pacific L24 North Texas L26 Ohio Valley L27 Oklahoma City L28 Oregon L63 Panhandle L29 Penn -Anthracite L30 Permian Basin L51 Peru L31 Philadelphia L32 Pittsburgh L33 St Louis L34 San Francisco L59 San Joaquin L35 Southeast L36 Southern Calif L69 Southern Calif Pet L53 South Plains L37 Southwest Texas L48 Southwest Alaska L38 Southwest N Mex L44 Spindletop L39 Tri-State L40 Upper Peninsula L41 Utah L70 Venezuela L42 Washington, D C L43 Wyoming L49 West Central Texas L46 Philippine

Jan 1, 1956

By WILLIAM BOWIE

THE development of the isostatic idea during the last century would make an interesting paper in itself. But the various steps in the development have been covered in a number of papers and books which are readily available. Therefore this short paper should not give space to. the historical phases of the subject. Isostasy is really an old idea, but it is only in the last few decades that it has taken on any great prominence or importance in the study of earth phenomena. It is really remarkable how closely Dutton&apos; sensed the isostatic principle 40 years or more ago. His general principles of isostasy as outlined by him have stood the test of time and fit in closely with the general ideas held today. It would seem, however, that some of his views with regard to the application of isostasy to geological processes must be modified or abandoned.

Jan 1, 1930

By AIME AIME

A REGULAR meeting of the Executive Board &apos;of American Engineering Council was held in the Onondaga Hotel, Syracuse, N.. Y., Feb. 14, 1921, with the president, Herbert Hoover, presiding. Reports of committees were presented and acted upon as follows: ENGINEER ON INTERSTATE COMMERCE COMMISSION The second meeting of the Committee was. called because it was represented to the Committee&apos; on Pro¬cedure that the American Society of Civil Engineers, the American Association of Engineers, and the Ameri¬can Institute of Consulting Engineers were anxious to have President-elect Harding appoint an engineer to fill one of the vacancies on the Interstate Commerce Commission. The representative of The American Society of Civil Engineers agreed to endorse the recom¬mendations- of American Engineering Council, and the Committee on Procedure prepared and sent a letter to the President-elect, a - copy of this letter being sent to each member of the Board. No names were suggested. . The appointment of an engineer on the Interstate Commerce Commission was approved and the Board, after approving the action of the Committee &apos;on Procedure in writing the President-elect, voted that, if requested, the Committee on Procedure submit a list of not less than six names for the appointment of an engineer on the Interstate. Commerce Commission.

Jan 1, 1921

At 8 o&apos;clock on the evening of Thursday, July 25th, the special train chartered by the Provincial Government for the Institute&apos;s use, pulled out of Toronto. Ten parlor cars and two dining cars made up the train. The culinary arrangements were under the personal supervision of Mr. McConkey, of Toronto. [ ] The Hon. Frank Cochrane, Minister of Mines, Lands and Forests, was the efficient host of the party. He was assisted by the Hon. Dr. Pyne, Minister of Education, and by Mr. T. W. Gibson and Dr. W. G. Miller. On arriving at Cobalt, the delegates were met by the following Committee Mr. A. A. Cole, representing the T. & N. 0. Railway; Messrs. R. W. Leonard and D. B. Rochester, deputies from the Cobalt Chamber of Mines ; Messrs. Run¬ning and Martin, from the Cobalt City Council; Messrs. McLeod and Ferland,

Jan 1, 1907

By F. M. Jardine

I1944 the cry was for higher production more tons, more metal. New plants were built, capacity of old plants was increased and millmen all over the country were treating tonnages far above normal, sacrificing recoveries to vet that extra metal from extra tons. The list of "critical minerals," at first long, has been scratched until there remains, not a list, but only an item or two. Stocks of all metals and minerals, with possibly one or two exceptions, are now entirely adequate and numerous plants have curtailed or suspended operation.

Jan 1, 1945

By G. C. Trevorrow

STRIP mining during 1943 increased considerably with further extension of mechanical loading in mines already partly mechanized; with the considerable introduction of mechanical loading into hand-loading mines; and with improvements in the use of loading equipment. Extension of the use of machinery both in strip mining and underground is due to reduction in labor supply and increased cost of labor, together with the increased demand for coal during the period of labor shortage.

Jan 1, 1944

The following is an incomplete list of members and guests who called at Institute headquarters during the period June 10, 1918 to July 10, 1918. F. C. Alsdorf, Tucson, Ariz. Emory M. Marshall, Camp Raritan, N. J. Juan F. Brandes, Santa Barbara, Cal. Jacques S. Negru, Camp Niagara, Ont. .H. Smith Clark, Kansas City, Mo. Arvid E. Nissen, High Bridge, N. J. J. S. Cunningham, Charleston, W. Va. Richard G. Place, So. Strafford, Vt. W. G. Eberhardt, Tucson, Ariz. Frank H. Probert, Berkeley, Cal. M. Eldredge, Bombay,. India. Martin A. Roudabush, Osterburg, Pa. A. D. R. Galloway, Accra, W. Africa;. P. H. Royster, Minneapolis, Minn. F. Hanst, Harrisburg, Pa. J. L. Schueler, Peoria, Ill. B. B. Hood, Chrome, N.. J. Henry B. Smith, New Britain, Conn. Paul S. King, Wilmington, Del. W. G. Sommer, Peoria, Ill. E. D. Kinney, Anaconda, Mont. A. L. Toenges, Roanoke, Va. E. W. Kohl, Jr., Philadelphia, Pa. G. D. B. Turner, Butte, Mont. James W. Love, Knoxville, Tenn. A. T. Ward, Bellefonte, Pa. Edwin A. Austin, formerly with the Yukon Gold Co., is superintendent of the Elkoro mine at Jarbidge, Nev. John W. Beard is now with the Cia Minera de Penoles, Ojuela, Dgo., Mexico, via Mapimi. R. S. Bonsib has accepted a position with the United States Emergency Fleet Corporation as District Safety Engineer, San Francisco, Cal. Albert Burch has been appointed by the Bureau of Mines to encourage the mining of chrome. F. B. Caldwell is working for the U. S. Bureau of Mines, under Albert Burch, in the investigation of chromite deposits. W. A. Carlyle has taken over the duties (in addition to his own) formerly assigned to E. P. Mathewson with the British America Nickel Corporation, at Sudbury, Canada. R. M. Catlin received the honorary degree of Doctor of Science at the recent commencement of Rutgers College, New Brunswick, N. J. S. K. Dahl is giving up his position as mill superintendent with the Messina Mines, which have been suspended, and is returning to this country. Algernon Del Mar has become manager of the Techatticup mines, El Dorado Canyon, Nev. Robert Dye has succeeded D. L. Forbes as manager of the Teck-Hughes at Kirkland Lake, Ont., Canada. J. O. Elton, superintendent of the Anaconda company&apos;s electrolytic zinc plant at Great Falls, Mont., is doing special work with the U. S. Bureau of Mines. R. B. Caples takes charge of the plant in his absence. George H. Gibbs has resigned his position as engineer at Messrs. T. & 1. Bradley & Sons, Ltd., Darlaston blast furnaces, Darlaston, and is now located at "Belmont." Litchfield Road, Rushall, Walsall, England. William D. Gordon, for the past 7 years manager of The Mine & Smelter Supply Co. at El Paso, has been elected president of Camphuis, Rives & Gordon,. Inc., and has opened American headquarters for the company at 81 New Street, New York, N. Y. E. Harms, for the past 16 years inn charge of metallurgical operations of the Torreon, Mexico; lead and copper smelter, has resigned and is now located at El Paso, Tex.

Jan 8, 1918

By SIDNEY ROLLE

ACURSORY glance through the literature on the subject reveals that the ablest minds in the land are devoting themselves to the great question of labor, of which employment is one of the fundamentals. Volumes have been written and the end is not in sight. Employment management is today about in the position that efficiency was 15 years ago. During the early days of the war, and perhaps for a year or so before, labor was plentiful. As the war progressed and Europe drew on us for munitions, employers began to compete with one another for&apos;, all, classes of labor. Labor was difficult to obtain, wages rose, the labor turnover increased, and employers began to install employment departments, welfare plans, and all sorts of schemes, but the labor efficiency dropped. As the war progressed, greater and greater production was demanded. New factors were introduced each day. The government, labor unions, industrial councils, all tended, it seemed, to make the situation almost intolerable. Wages rose to fantastic heights, the cost of living rose higher and higher, and the efficiency dropped still further.

Jan 1, 1921

By R. W. Raymond

(Chattanooga Meeting, October, 1908.) THE immense commercial value of the Gayley dry-blast process has been established beyond controversy. The testimony of practical blast-furnace managers, on both sides of the Atlantic, agrees that it reduces the cost of pig-iron about $1 per ton; but from the same testimony it appears that this direct economy does not by any means cover its commercial advantages-in fact, that under conditions frequently encountered in practice, it presents other benefits of even greater immediate financial importance. To this point I shall recur in a later part of the present paper. The history of the reception given to this invention, especially on the other side of the Atlantic, has repeated an experience familiar to American engineers. First, the reports of our practice were rejected as theoretically impossible, according to generally accepted notions and formulas; then the figures were reluctantly accepted ; and finally the attempt has been made to explain how they could have been obtained. As to the Gayley dry blast, we Americans have been for several years in the last stage of the discussion, and the rest of the professional world is rapidly coming to it. Meanwhile, the remark has been repeatedly made that, whatever Mr. Gayley&apos;s process may turn out to be worth, it was not an invention on his part, but simply the energetic and persevering execution of a procedure already proposed by others. This question I wish to discuss first in the present paper. I. WHAT DID MR. GAYLEY INVENT Realizing that this is not the place for detailed argument on an issue of patent law, I shall not undertake to quote and criticise the publications prior to Mr. Gayley&apos;s first patents. It may be admitted, without such critical analysis, that the possi-

Jan 1, 1909

By I. Plaskin

Interaction of sulfide minerals and native metals I with reagents in flotation is largely determined by particle-surface changes resulting from action of the medium and dissolved gases. A number of early studies were devoted to the selective action of various gases on minerals.&apos; Mc-Lachlan&apos; paid attention to oxygen as the most active gas affecting flotation properties of sulfide minerals. Opposing views were expressed concerning the influence of sulfide oxidation on xanthate flotation: Taggart3 recognized the positive influence of oxygen, and I. W. Wark4 rejected it. Shvedovh ffered the hypothesis of partial oxidation. As to the influence of such gases as hydrogen" and carbon dioxide on mineral floatability, opinions also differed. Effect of Oxygen on Sulfide Mineral Flotation: Research on the influence of oxygen and other gases on the floatability of sulfide minerals and native metals has been carried out at the Institute of Mining of the USSR Academy of Sciences in

Jan 1, 1960

W. L. Saunders, New York, N. Y.:—Mr. Parker&apos;s paper, though entitled Conservation of Coal, might also be called the Conservation of Life in the Coal-Mines of the United States. No subject is of greater importance to mining-men at the present time than information from experts as to how to save coal and how to save human lives in mines. That the casualties in the coal-mines should exceed 3,000 in the year 1907 is simply appalling, and that 1,000 men should have been killed in a single year through explosions alone, and that so good an authority as Mr. Parker should say that " a prolific cause " is an "improperly-prepared blast" or "the failure on the part of the miner to undercut his coal," points to the importance of activity not only among mining engineers but also, through experts, by the legislatures of the respective States. There is but little doubt that nearly all the serious coal-mine

Jan 1, 1910