Search Documents

By C. G. Brehm

THE anthracite-producing region is in the northeastern section of Pennsylvania, and has an area of approximately 484 square miles. It is divided geographically into three separate fields, known as the Northern, Middle and Southern. The Northern field, with Wilkes-Barre approximately at its center, is a basin about 60 miles long and almost 6 miles wide at its greatest distance across. Generally speaking, it may be said that the coal meas-ures in this field lie horizontally, or on slight pitches, and consist of from 11 to 19 veins of coal, varying in thickness from several inches to several feet. The intervening strata between veins may be composed of slate, clay, rock or shale, or a combination of several, and are sometimes very thin. This condition often causes a treacherous roof, therefore roof sup-port and the attending hazard of mining are problems of concern. The Middle field is made up of a number of small basins of not very great depth, and the measures, which are in like number to those of the Northern field, are varying inclinations running from nearly flat to steep pitches.

Jan 1, 1938

By W. R. Crane

THE effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. There is no doubt but that in time, because of failure of pillars, extensive fracturing and widespread settlement of the surface will result, particularly along the slope of Red Mountain, where mining has been under way for many years. Were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Until development openings and surface plants are transferred to Shades Valley, protection of the surface will probably not be considered imperative, as the area involved is not of particular value for agricultural or building purposes. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. The occurrence of heavy beds of strong tough materials at varying distances above the orebed make it doubtful whether any serious disturbance of the surface will be experienced at any considerable distance from the outcrop, although some settlement will probably take place. It is certain, however, that no great volume of water will enter the mines from fracturing of the Fort Payne chert bed, as this is known to be a compact and practically impervious formation beyond the leached zone. Not so much can be said, however, regarding other possible sources of water, as pervious beds and through faults that may be encountered in future mining operations.

Jan 8, 1925

By T. R. A. Davey

A Survey of current and recent research and developmental work is supplemented by predictions for processes which should be developed over the reminder of this century.

Jan 1, 1970

By E. H. Griswold, C. E. Beecher

DURING 1931 the petroleum industry has faced the most hazardous periods of its existence, caused by large potentials, overproduction, and demoralized markets. Two state governors actually resorted to the use of the militia in an effort to restore a semi-stabilized condition within the industry, to prevent waste of the states' natural resources, and to restore prices to a level that would yield the states a reasonable tax revenue. These conditions have made it necessary to put into effect most. stringent economies and have produced a spirit of cooperation between companies to an extent that never before existed. The necessity for unified action on such matters as proration and the advantages to be gained by unit operation are being realized by the oil industry as a whole. Fewer wells have been drilled and wildcat operations almost eliminated: development and operation costs have been greatly reduced and more attention is being paid to efficient recovery methods. The net work of oil pipe- lines has grown rapidly especially in the area of East Texas. The construction and operation of natural gas and gasoline pipelines into areas far distant from the source of supply has been one of the outstanding accomplishments. Refining efficiency has continued to increase and the public is being supplied with a better grade of gasoline at a lower price. The unreasonable tax which state politicians have succeeded in placing on gasoline has encouraged tax evasion and unfair competition by un- scrupulous dealers and has misled the public as to the true price of gasoline.

Jan 1, 1932

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By E. Stansfield, J. W. Sutherland

It is well known that the ash left when coal is burned is not the same either in chemical composition or in weight as the mineral matter originally present in the coal. This mineral matter has been referred to as "mineral impurity," "ash-forming constituents" and "corrected ash." The authors prefer the simple name used in the title and throughout this paper. The mineral matter in a sample of coal cannot be isolated unchanged and then weighed; but if the relation between the weight of mineral matter in the coal and the weight of ash remaining when the coal is burned can be ascertained, the weight of mineral matter in the sample can be calculated from the determined weight of ash. When the weight of mineral matter in the sample is known, the weight of pure coal can be found by subtraction. This pure coal must be the basis of accurate coal classification. W. F. Wheeler,l,3 W. Brinsmaid,2 S. W. Parr, and many subsequent workers have studied the relation between mineral matter and ash. Wheeler and Parr and others have deduced formulas for calculating this ratio, and used heavy-solution separations for checking the accuracy of their formulas. Brinsmaid hand-picked and analyzed two separate samples (and mixtures of these) and based thereon a graphical method of deducing the ratio. In the Fuel Testing Laboratories of the Scientific and Industrial Research Council of Alberta, a graphical method, based on heavy-solution fractionation of coal samples, has been used with marked success for the past 7¼ years for determining the mineral matter-ash ratio. This method resembles that employed by Brinsmaid in 1907.

Jan 1, 1930

By Eugene A. Stephenson

The writer apologizes for presenting this very elementary analysis of one aspect of proration, but a search of the literature failed to disclose any concrete illustrations of the effect of various proration formulas upon the allowable oil produced by tracts of different sizes. Many engineers have doubtless made somewhat similar calculations and are fully acquainted with the results. The various allocation formulas that are in use are based on one or more of the following factors: (1) wide-open well potential, (2) potential through an orifice, (3) uniform well allowable, (4) acreage, (5) sand thickness, (6) bottom-hole pressure, (7) productivity index, and (8) volumetric displacement. Of these, the unrestricted potential formula, or open-flow test, and the uniform well allowable are commonly regarded by engineers as those least likely to give each producer his proportionate share of the oil or gas, as represented either by acreage or by sand thickness, or both, except when the wells are located on tracts of large size. Unless the mechanical equipment that may be used during the potential test and the method of taking the test are both specified, the net result of the potential formula is to practically force the operators to use special equipment and adopt special procedures prior to and during the potential test, so as to secure the largest possible allowables. Much ingenuity and skill have been devoted to this,problem, but the general effect is to permit excessive allowables for very small tracts, and stimulate unnecessary drilling. It is interesting to compare some of the high yields from the Wilcox horizon at Oklahoma City with each other, as an illustration of the effect of an allocation factor based solely on potential (Table 5). One of the glaring instances is a well on a ½-acre lease, which had produced, as of September 1936, at the rate of almost 3,000,000 bbl. per acre. This is at least twice as many barrels as could have been present under the property if the reservoir had consisted of a tank of oil 200 ft, deep and 56 acre in area. Numerous combinations of acreage, potential, bottom-hole pressure, sand thickness, etc., have been proposed and are in use in various fields.

Jan 1, 1937

By H. B. Bell, P. C. Lidster

A study has been made of the use of ThO2-Y2O3 solid electrolytes to determine activity of chromium in Fe-Cr and Ni-Cr alloys in the temperature range 1300° to 1700°K. This method has been shown to give results which agree with the best vapor pressure measurements. SEVERAL investigations1"5 have been made of chromium activities in Fe-Cr alloys. Most of these have been made by vapor pressure measurements using knudsen cell techniques while one has been made using gas equilibration with H2/H2O gas mixtures. In the present investigation electromotive force measurements have been made on this system using a thoria yttria solid electrolyte. This system was -chosen to establish the technique of measurement at low oxygen potentials, before extending it to Fe-Ni-Cr alloys. The cell used was Pt Cr • Cr2O3 ilThO2 • Y2O3 llalloy • Cr2O3 IPt Since the oxygen pressure of the chromium-chromic oxide mixture lay in the range 10"19 to 1027 atm in the temperature range investigated, thoria yttria electrolytes were used. It was soon found during the investigation that considerable care was required to prepare satisfactory electrolytes and a study was made to find the best method of preparing pellets of TI1O2-Y2O3 solid solution of as near theoretical density as possible. Various compositions in the range 2 to 15 mole pct Y2O3 were studied but the experimental measurements were made with electrolytes containing 4 to 5 pct Y2O3. The method of preparation finally adopted was to use thorium oxalate and yttria as raw materials. The thorium oxalate was decomposed at 900°C for 6 hr to give a reactive powder. This powder was then mixed with the appropriate amount of yttria and ground in an agate mortar for about 4 hr. The powder was moistened with absolute alcohol as a lubricant and pressed in a metal die at a pressure of 7 tons per sq in. The pellets were then heated at 1100°C for 24 hr followed by 24 hr at 1250°C. After this firing cycle the material was reground and repelleted and again fired at 1100° and 1250°C followed by heating for 7 days at 1600°C. It was found in later experiments that a further firing of 4 hr at 2000°C improved the density further and gave pellets of only 2 pct porosity. After firing, the pellets were polished on emery paper and finally with the 2 µ diamond paste. The polishing was followed by a final firing of 24 hr at 1500°C. Investigation showed that this final treatment minimized reaction between the electrolytes and chromium oxide. It was believed that this was because of a lowering of the surface energy of the electrolyte surface. Two types of investigation were carried out to check that the pellets were satisfactory oxygen ion elec-

Jan 1, 1970

By Robert D. Longyear

IN MOST diamond core drilling the primary objective is the recovery of samples to be used for chemical analysis, physical tests, or visual inspection. Unless these samples are reliable and the information systematically recorded, the time and money spent in securing them are largely wasted. A properly taken diamond-drill sample is similar to a properly moiled channel sample but more accurate. No channel sample can be moiled in as even a groove as the smooth cylinder of material normally removed in diamond drilling. More important still, sampling by the diamond drill practically eliminates that personal equation which Jora1emon4 reference numbers apply to publications listed in the bibliography at the end of this article) has aptly termed "the almost magnetic attraction of the most conscientious hand toward rich pieces of ore."

Jan 1, 1937

By WALTER VOIGTLANDER

FOR nearly 100 years wire rope has been fabricated in much the same way. To the great majority of mine superintendents wire rope is just wire rope, little or no semblance of individuality or identifying characteristics. Such an impression was fairly justified until three or four years ago when a practical means was found of performing or preshaping the wires and strands. This discovery permitted a revolutionary change in wire rope manufacture. Instead of merely twisting a number of wires into a strand, then twisting several strands into a complete rope (which twisting would naturally result in great internal strain, thus reducing the resiliency and over-all efficiency of the completed rope), the preformed wires and strands were laid in place without force or twisting. The obvious result was a rope more nearly approximating mechanical perfection. The applied loads are more evenly distributed throughout the component wires and strands, thus reducing unbalanced wire stresses. This results in a higher safety factor. The fact that preformed rope will not unravel when untied at the ends proves the absence of a torsional stress that exists in ordinary rope. A greater useful allowable stress in the wires is therefore possible in actual operating service.

Jan 1, 1926

By Edward Keller

Jan 1, 1906

ALABAMA Aldrich.-Lloyd, T. W. Anniston.-Carrington, F. G. Klugh, B. G. Bessemer.-Abbott, C. E. Dobbs, G. G. Ferguson V. Salmon, h. S. Stuart, Q. W. Birmingham.-Adams, J. H. Aldrich, T. H. Aldrich, T. H., Jr. Allen, A. W. Armstrong. W. D. Ball, E. M. Bonnyman, J. Bush, M. W. Carter, E. Crawford, G. G. Davis, C. B. Dryer. T. B.

Jan 1, 1923

By D. K. Crampton

The object of this work was to obtain and correlate information on effect of internal stress in variously drawn tubes on several properties. Also, a simple approximate method of comparing types of stress distribution in such variously drawn tubes was sought. There is also included some work on comparison of single and polycrystalline materials and effect of different types of operation and preferred orientation. Preparation of Material A series of tubes was drawn to study the effect of the type and degree of final reduction on various physical properties and the approximate distribution of stress intensity across the tube wall. The material used all came from a single heat of 70-30 brass melted in a regular production Ajax-Wyatt induction furnace. The analysis of the metal as cast was: copper, 70.36 per cent; lead, 0.04; iron, 0.02; zinc, balance. The material was cast in "shells" with 4 in. outside diameter and in. wall thickness. It was drawn part way down according to the usual standard mill schedule and then by suitable individual schedules to finish by a variety of types and degrees of drawing to the same final cases in every instance; namely, 0.750 in. outside diameter by 0.080 in. wall thickness. The exact final draws, together with the percentage area reductions, diameter reductions and gage reductions are given in Table 1. In fabricating these tubes, rather unusual precautions were observed to insure the elimination of ail variables not under immediate study. All intermediate anneals were carried out at about 1200" F. down to the so-called "cut-in size"; namely, 17/16 by 3/16 in. From this point on, all anneals were made at from 1050' to 1100" F. The greatest care was used all through to have the tubes as free from minor surface defects as possible. When such defects were visible on intermediate sizes they were carefully filed out. On the final draw to 3/4-in diameter the die was aligned with the greatest possible precision in order to insure as straight a tube as possible

Jan 1, 1933

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By J. Brian Eby

The Gulf Coast of southern Louisiana during the year of 1940 was subjected to an extensive exploration and development campaign, as a result of which 16 oil fields and about 38 new producing sands were found. Although this record of discovery appears in keeping with the rate of 1939 actually in amount of new proven reserves, it may fall short of that of the previous year. Only five or six of the discoveries rated as first-class or important fields at the close of the year. The most prominent new fields opened during the year were Neale field in Beaure-gard Parish, the West Cote Blanche field in St. Mary Parish, the Stella field and the West Bay field in Plaquemines Parish, and the Lake Salvador field in St. Charles Parish. There were many important oil-sand discoveries in proven fields, such as in the Bayou Perot field, the Golden Meadows field, the Iowa field, West Lake Verrett field, and the Venice field. During the year, 1047 weUs were drilled in southern Louisiana, of which 768 were completed as oil-producing wells, 17 as gas wells and 262 as dry holes. The Neale field in northwest Beauregard Parish is considered one of the most important discoveries of the year. The f~eld centers around the north half of sec. 26, 'Y.3 S., R.I I W., just north of the town of Neale. It was discovered by the Atlantic Refining Co., using reflection seismograph to locate the structure. Production was found in the second well drilled in the Wilcox sand on the downthrown side of a fault. The structure is known as the "Tepetate" type, being similar to that of the well-known Tepetate field. There were 12 oil wells and 3 dry holes drilled during the year. The Wilcox sand in this field occurs between 8350 and 8400 ft. and averages 30 ft. in thickness. The West Cote Blanche Bay field, in West Cote Blanche Bay, St. Mary Parish, is a 1940 discovery by the Texas Company, credited to reflection seismograph exploration. The oil is from two sands occurring at 3110 to 3140 ft. and from 4950 to 5020 it. Four wells were drilled during the year, three oil wells and one dry hole. The deepest hole drilled reached 9491 ft. without encountering salt or dome material. In Plaquemines Parish, south of New Orleans, the California company has a new field known as the Stella field. The sand was found at a depth of 7485 ft., and 5 ft. of perforations made a well capable of producing 486 bbl. of oil in 24 hr. through a 9.is-in. choke. The oil is 42" gravity. The discovery well was drilled to a total depth of 10,258 ft. and other producing sands were indicated. A good field appears assured, although only one well was completed within the year. The Lake Salvador field, in the center of Lake Salvador, St. Charles Parish, gives promise of being one of the most important discoveries of the year. The discovery well was perforated at 9775 to 9800 ft. making 850 bbl. of 33.7° gravity oil daily through a 1/4-in. choke. Three wells were completed in 1940 but few details have as yet been made available.he Gulf Oil Corporation apparently has a good field in its wildcat discovery in West Bay, Plaquemines Parish. This well found

Jan 1, 1941

By J. Brian Eby

The Gulf Coast of southern Louisiana during the year of 1940 was subjected to an extensive exploration and development campaign, as a result of which 16 oil fields and about 38 new producing sands were found. Although this record of discovery appears in keeping with the rate of 1939 actually in amount of new proven reserves, it may fall short of that of the previous year. Only five or six of the discoveries rated as first-class or important fields at the close of the year. The most prominent new fields opened during the year were Neale field in Beaure-gard Parish, the West Cote Blanche field in St. Mary Parish, the Stella field and the West Bay field in Plaquemines Parish, and the Lake Salvador field in St. Charles Parish. There were many important oil-sand discoveries in proven fields, such as in the Bayou Perot field, the Golden Meadows field, the Iowa field, West Lake Verrett field, and the Venice field. During the year, 1047 weUs were drilled in southern Louisiana, of which 768 were completed as oil-producing wells, 17 as gas wells and 262 as dry holes. The Neale field in northwest Beauregard Parish is considered one of the most important discoveries of the year. The f~eld centers around the north half of sec. 26, 'Y.3 S., R.I I W., just north of the town of Neale. It was discovered by the Atlantic Refining Co., using reflection seismograph to locate the structure. Production was found in the second well drilled in the Wilcox sand on the downthrown side of a fault. The structure is known as the "Tepetate" type, being similar to that of the well-known Tepetate field. There were 12 oil wells and 3 dry holes drilled during the year. The Wilcox sand in this field occurs between 8350 and 8400 ft. and averages 30 ft. in thickness. The West Cote Blanche Bay field, in West Cote Blanche Bay, St. Mary Parish, is a 1940 discovery by the Texas Company, credited to reflection seismograph exploration. The oil is from two sands occurring at 3110 to 3140 ft. and from 4950 to 5020 it. Four wells were drilled during the year, three oil wells and one dry hole. The deepest hole drilled reached 9491 ft. without encountering salt or dome material. In Plaquemines Parish, south of New Orleans, the California company has a new field known as the Stella field. The sand was found at a depth of 7485 ft., and 5 ft. of perforations made a well capable of producing 486 bbl. of oil in 24 hr. through a 9.is-in. choke. The oil is 42" gravity. The discovery well was drilled to a total depth of 10,258 ft. and other producing sands were indicated. A good field appears assured, although only one well was completed within the year. The Lake Salvador field, in the center of Lake Salvador, St. Charles Parish, gives promise of being one of the most important discoveries of the year. The discovery well was perforated at 9775 to 9800 ft. making 850 bbl. of 33.7° gravity oil daily through a 1/4-in. choke. Three wells were completed in 1940 but few details have as yet been made available.he Gulf Oil Corporation apparently has a good field in its wildcat discovery in West Bay, Plaquemines Parish. This well found

Jan 1, 1941

By J. F. Stiehr, R. L. Sanford, T. L. Myers

This paper summarizes the development of a Directory of Computer Programs Applicable to US Mining Practices and Problems. The directory is funded by the US Bureau of Mines and includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various US government agencies. General references to computer applications throughout the mining industry are discussed as well as the availability of programs to interested organizations or individuals.

Jan 9, 1979

By E. Gybbon Spilsbury

Everybody who has had his attention turned to the gold-deposits of the Southern States, is acquainted with the undisputed fact of the existence, at least in the Carolinas and Georgia, of enormous areas of gold-bearing rocks. Long before the discovery of the precious metal in California, gold-mining on a very extensive scale mas a well-estab-

Jan 1, 1887

Institute of Metals Division Iron and Steel Division Extractive Metallurgy Division Council A W Thornton (ISD), Chairman, R W Shearman, Secretary, C S Barrett (IMD), J C Kinnear, Jr (EMD), John Chipman (ISD), J S Smart, Jr (IMD), A W Schlechten (EMD), M E Volin (MED), D S Eppelsheimer (MIED) Journal of Metals Editorial Advisory Committee J S Smart, Jr, Chairman, W A Dean, J J Golden,T D Jones, Evan Just, J C Kinnear, Jr, M Tenenbaum Pacific Northwest Regional Conference E R Marble, General Chairman, Marshall Huntting, Assistant General Chairman, W C Douglass, Mining Chairman, H C Hughes, Mining Chairman for British Columbia, W C Douglass, Mining Chair¬man for United States, Paul Billingsley, Geology Chairman, W D Nesbeitt, Miner¬als Beneficiation Chairman, H D Kelley, Industrial Minerals Chairman, J G Johnston, Metals Chairman, Lloyd Banning, Iron and Steel Chairman, W G Rouillard, Extractive Metallurgy Chairman, E C Roberts, Physical Metallurgy Chairman, D A Pifer, Mineral Industry Education Chairman, Frederick Brien, General Arrangements Chairman Metals Branch Membership Committee C M Squarcy, Chairman, R C Cole, Harold Mar¬golin, M E Nickel, S K Scovil Bylaws Committee A W Thornton, Chairman, W R Hibbard, Jr, J S Smart, Jr (IMD), John Chipman, T S Washburn (ISD), T D Jones, J D Sullivan (EMD)

Jan 1, 1956