Search Documents

By Daniel T. Hegyan, Thomas B. Zugates

Continuous vacuum disk filters are increasingly being used to filter refuse from the fine-coal washing circuits as it becomes important to close the water circuits and eliminate sludge holding ponds. This paper discusses our past experience filtering refuse, effects of solids concentration in the filter feed, use of polymer flocculation aids, effect of flocculation devices, and effects of particle size and ash content on the filtration rate. Detailed tests were performed on existing installations utilizing coal refuse filters to determine optimum flocculant dosage, solids concentration, and disk rotation speed to form a dischargeable cake. Information was also obtained showing effect of flocculant addition on the moisture of the filter cake.

Jan 1, 1977

By Freeman Bishop

The tight electric power supply is one of the most dramatic problems facing the mining industry in 1971. This is caused by rising demands for energy. Clean-fuel and air-pollution controls have contributed to the problems of producing energy from sulfur oil and coal. Coking coal has become scarce. One stimulating development is that coal is no longer the cinder in the mining industry's eye. In fact, it may be the favorite candidate as a base for fuel within a few years. Synthetic gas from coal is the watchword. In dedicating a multi-million- dollar project aimed at converting coal into oil and gas, Hollis M. Dole, Assistant Secretary of the Interior, recently made it clear that coal, which has been taking a back seat to nuclear fission research and study grants, is now coming into its own. Conversion pilot plants are being activated in all parts of the nation.

Jan 1, 1970

By P. Barnes

Several interesting and important considerations may be based upon an analysis of the cost of producing Bessemer rails, and the facts thus set forth may be much more clearly emphasized by re ducing each item of cost to its own fractional proportion of the sum total in each branch of the manufacture. The estimate given below is not absolutely complete in minute ness of detail, but it may be fairly taken as a basis for the suggestions to be noted : Perhaps the most striking comments that can be made upon this statement are those arising from a consideration of some of the smaller items, and even the least of these quite loses its insignificance when its proportion of the whole is expressed in actual money, as for the work of a year, or even for a single day. Thus, if the item as be considered, the importance can be clearly

Organization Place _ Date 1919 American Iron and Steel Institute New York, N. Y. May National Fire Protection Association Ottawa Can. May 6-8 American Zinc Institute :.. St. Louis, Mo. May 12 American Association of Engineers Chicago, Ill. May 13-14 Natural Gas Association in America Cleveland, 0. May 20-23 American Institute of Electrical Engineers.... Lake Placid, N. Y. June 24-27 American Society for Testing Materials Atlantic City, N. J. June 24-27 American Institute of Min. and Met. Engineers Chicago, Ill. - Sept. 22-27 American Steel Treaters' Society, First Annual Convention Chicago, Ill. Sept. 22-27 National Safety Council Cleveland, U. Sept. 29-Oct. 2 American Foundrymen's Association Philadelphia, Pa. Sept. 29-Oct. 4 Institute of Metals Division, A. I. M. E Philadelphia, Pa. Sept. 29-Oct. 4 American Ry. Bridge and Building Association Cleveland, 0. Oct. 21-23 Geological Society of America Boston, Mass. Dec. 29-31

Jan 5, 1919

By James M. Polatty

FOR structural as well as economic reasons, sanded grout rather than neat cement grout should be used wherever possible. The chief drawback in using sanded grout mixtures, however, is the tendency of the sand to settle out, causing problems in pumping. Manufactured sands have not been used in sanded grout because it has been assumed that their irregular particle shape would add to the pumping difficulties. The Concrete Division of the Waterways Experiment Station in Jackson, Miss., has conducted a comprehensive investigation of grouts containing both natural and manufactured sands. In the study of manufactured sand grouts an investigation was made of physical characteristics, ease of pumping, and the effects of adding certain mineral fines. The amount of material passing 100 mesh ranged from zero to 25 pct. Results were compared with test results for natural sand grouts.

Jan 3, 1958

By H. W. Peirce

Identified and utilized Arizona salt deposits are of two ages: 1) Permian in the Colorado Plateau, and 2) Tertiary in the Basin and Range country. Uses include: a) storage of energy fluids in man-made solution cavities in both Permian (Supai Formation) and Tertiary (Luke salt body) salt and b) production of marketable products by solution and evaporation of tertiary salt. The two liquid petroleum storage Projects have a combined storage capacity in excess of 380 million L (100 million gal). Current production of salt products approximates 32 kt/a (32,000 stpy). Increasing demand for both storage and salt products is anticipated.

Jan 1, 1983

By John K. Irwin

Friction hoisting has assumed a major role since its introduction to North America less than ten years ago. Interest was illustrated by a recent visit of the Adirondack Section of AIME to a new friction hoist at Chateaugay mine of Republic Steel Corp. at Lyon Mountain, N. Y. The 80-in. diam, 4-rope machine at Lyon Mountain is typical of modern friction hoists. The hoist is mounted on a structural steel tower without deflection sheaves.

Jan 10, 1963

By Thomas M. Drown, P. W. Shimer

In a communication to this Institute at the Baltimore meeting, February, 1879,* on the "Determination of Silicon in Pig Iron and Steel," the method recommended was the treatment of the metal with nitric acid until action had ceased, and then evaporating with sulphuric acid until the nitric acid was nearly or quite driven off. After filtration of the siliceous and carbonaceous residue, and washing with hot water and hydrochloric acid, a silica was obtained, on ignition, which was quite pore. Since this paper was read before the Institute, we have had large experience with the method, and

Jan 1, 1880

By R. Stefanko, R. H. King, L. A. Morley

Coal mine fires, injuries and electrocutions, and many production delays have resulted from trailing cable splice failures. Research was carried out at The Pennsylvania State University to determine the failure causes and recommended solutions. The study revealed that current splice kit materials are generally adequate with the exceptions of connector flexibility, adhesives bonding, and abrasion characteristics of taped jackets. Research indicated that the most prevalent breakdowns result from workmanship defects. Therefore, guidelines for improved splice construction are reported in detail.

Jan 1, 1976

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mining, Geology and Geophysics Division Council Will Mitchell, Jr, Chairman (MBD), Kenneth L Cook, Vice-Chairman (MGGD). Edward L Clark (MGGD), Raymond B Ladoo (Ind Min Div), Sandford S Cole (Ind Mm Div), Norman L Weiss (MBD), C T Hayden (Coal), H F Yancey (Coal), Clayton G Ball (MED), P De Bruyn (MIED), Arnold Buzzalini, Secretary, AIME, 29 West 39th Street, New York 18, N Y Mining Branch Advisory Committee Will Mitchell, Jr, Chairman, Grover J Holt, J B Morrow, J L Gillson, Edward G Fox, S S Cole, Roger V Pierce, Norman L Weiss. H C Weed. J R Van Pelt

Jan 1, 1956

By G. E. Karantzavelos

A novel two-stage froth flotation process for the recovery of pure magnesite from low grade ores is described. The process consists of a first-stage, magnesite flotation step where a rougher magnesite concentrate is floated with amine collectors. The first-stage froth concentrate is then repulped in fresh water, and quartenary ammonium salt and fuel oil are added to float the remaining impurities. The results from laboratory batch tests show that a high-grade magnesite concentrate assaying 0.99-0.20% Si02 and 2.84-0.46%a Ca0 can be produced. Regulation of the variables controlling magnesite froth flotation also allows the variation of the ratio % Ca0: % SiO2, between the acceptable limits 0.32 to 5.79. This ratio is important to the quality of dead-burned magnesite.

Jan 1, 1985

By K. J. Anusavice, R. T. DeHoff, H. Oikawa, J. J. Pinajian

STUDIES of nickel self-diffusion and impurity diffusion in pure metals and alloys have, for the past two decades, employed predominantly the nickel radio-However, because of the low energy of the emitted particle, careful and time-consuming techniques must be used to obtain reproducible measurements. In our studies of nickel diffusion into copper, we have recently used Ni66 [Td1/2: 55 hr; : 0.20 Mev (100 pet)] which decays to it much more suitable as a tracer because of the presence of the high-energy y radiation from the cu66 daughter. Although the half-life of Ni66 is appreciably shorter than that of Ni63, the useful working lifetime of a small quantity, " 10 mc, is about 1 month. preparation bf Ni66. he Nis6 radioisotope was produced at Oak Ridge National Laboratory by means of a double (n,y) reaction:

Jan 1, 1969

COMMITTEE IN CHARGE SPENCER PENROSE, Chairman A. E. CARLTON, Chairman Finance Committee GEORGE M. -TAYLOR, Vice-chairman. J. DAMSON HAWKINS, Secretary DENVER COLORADO SPRINGS Finance Finance T. B. STEARNS A. E. CARLTON RICHARD A. PARKER SPENCER PENROSE T. B. BURBRIDGE GEORGE M. TAYLOR A. L. BLOOMFIELD, Treasurer Arrangement Registration DAVE G. MILLER LOREN C. LENNOX FRANK BULKLEY HORACE F. LUNT GEO. E. COLLINS J. M. TIPPETT Entertainment Arrangement and Entertainment F. H. BOSTWICK GEORGE M. TAYLOR F. E. SHEPARD J. D. HAWKINS HOWLAND BANCROFT A. E. CARLTON B. P. MORSE A. L. BLOOMFIELD J. G. PERRY THOMAS B. CRONE E. P. ARTHUR ETIENNE A. RITTER CRIPPLE CREEK PUEBLO THOMAS B. CRONE J. F. WELBORN E. B. ARTHUR H. B. CARPENTER N. S. GREENSFELDER L. B. EAMES A. E. CARLTON F. ROBINSON B. F. HILL J. G. WILLIS

Jan 8, 1918

By A. U. Seybolt, F. J. Norton

A standard technique for heat treating small metallurgical samples where no appreciable contamination from the atmosphere can be tolerated is that of sealing small samples in evacuated fused-silica tubes. Since vitreous silica is relatively impervious to diffusion of gases, even at temperatures approaching the devitrification range, around 1100°C, this simple procedure has been very widely adopted as a standard technique in metallurgical research. Many workers have recognized that, with metals of fairly high reactivity, insulation from direct contact with the SiOz envelope is desirable in order to avoid displacement reactions of the type M + SOz-- MOz + Si(in M). It is not so generally known, however, that the 'rate of permeation of oxygen from the air through the SiOz enclosure at tem-

Jan 1, 1964

By T. E. Scott, O. G. Koepke

DURING research currently in progress the need arose for interplanar angles and planar spacings to analyze crystallographic data obtained from hcp yttrium. In the absence of such existing information, a program was written in Fortran-11 language and processed on an IBM 7074 computer. The program and results have been assembled in report form to make them generally available.' Of the possible combinations of, only those most frequently encountered were employed. The ranges of h, k, and 1 involved were: However, not all combinations and permutations of the above appear in the tabulation because redundancies occur in several cases. Nevertheless, fifteen types of planes and all their equivalent planes have been included, giving a total of 109 sets of Miller-Bravais indices.

Jan 1, 1967

By J. F. Cuderman

A technique using propellants has been developed for producing multiple fractures about a wellbore. The use of propellants having a range of burn rates permits precise control of combustion gas release and thereby of borehole pressurization. The pressure rise- time is the key variable governing fracture behavior. The peak pressure attained is of secondary importance and appears to be a function of in situ stress and loading rate. The fracture geometry is governed by the in situ stresses and pressure risetimes. The major fractures occur along the principal planes of stress and along apparent planes of maximum shear stress.

Jan 1, 1984

By Per-Martin Sandgren, Alrik Anttila

LKAB's ores have specific mineralogical properties that make them especially suitable for the production of supergrade concentrates. Conditions are particularly good for this purpose at Malmberget, where a concentrate for high-purity sponge iron production has been produced for many years. This product assays approximately 71.5% Fe and 0.20% SiO2. Potential exists for still further improvement. In recent years, the production of fractioned concentrates has been started. The material lies within the size range 74-125 µm and the approximate chemical analysis is 71.4% Fe and 0.30% SiO2. Other special products are under discussion. Malmberget ores are also suitable for the production of high- purity direct reduction pellets with a SiO2 content below 1%.

Jan 1, 1983

A special meeting of the Board of Directors was held on July 25, 1916, pursuant to notice duly given according to the By-Laws. This special meeting was for the purpose of giving authority for the signing of a contract with the American Society of Civil Engineers, as mentioned in another place in this Bulletin. The interest in the matter is indicated by the attendance of 11 members of the Board, some of whom came from a long distance. An invitation was received from the St. Louis Section of the Institute and from members in and near St. Louis to hold the 115th Meeting of the Institute in and near St. Louis in late September or early October, 1917. This invitation was accepted. Announcement was made that the Mexican Institute of Mining and Metallurgy had been dissolved and reorganized as the Mexican Section of the Institute.

Jan 9, 1916

By Van C. Nyman

A time-sharing computer was tied in to Hecla in August of 1967. This has proven to be helpful in performing metallurgical and engineering calculations that were formerly tedious tasks. Metallurgy programs were written for applying two and three product formulas. Programs were expanded to make the monthly metallurgical balance calculations for each of the Hecla mills. The Hecla engineering department uses the computer for solving hoist duty cycles and for traverse analysis. Both Asarco and Bunker Hill Company in the Coeur d’Alene Mining District are tied to a time-sharing computer. Their uses for the time-sharing computer will be discussed. Asarco had the advantage in learning computer techniques during an extended strike. A comparison of Asarco computer use with that of Hecla's will show the advantage in having a person or persons spend full time on the use of computers. Bunker Hill has the versatility of five teletype units in their mine-smelter complex plus ability to tie in to their own computer.

Jan 1, 1969

Prof. Dr. H. Seger and Mr. E. Cramer, Chemisches Laboratorium fur Thonindustrie, Berlin, Prussia (communication to the President)* : We have learned, with much interest, from the pamphlet sent to us, of the work of Messrs. Hofman and Demond, particularly as we observe from their experiments that these gentlemen recognize the usefulness of the Seger cones, and that this method of determining temperatures in the furnaces of the ceramic industry and in the tests of refractory clays is valued, not only in all parts of Germany, but also in other countries. Permit us to say, with reference to the crucibles employed in tests for refractoriness, that we have used of late, besides the magnesia crucibles, also those made of Zettlitz kaolin, with the addition of alumina, previously calcined, with regard to which we beg to refer to our article in the Thonindustrie-Zeitung of December 9, 1893.

Jan 1, 1895