Search Documents

By A. M. Gaudin, C. S. Chang

Adsorption was measured for barium ion and laurate radical, using radioactively marked agents, over wide range of concentrations. Laurate adsorbed in absence of barium fails to float. With barium, flotation-effective laurate coating needs not exceed 5 pct of monolayer. Barium adsorption then is several fold larger. No barium laurate coating is obtained. IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.'-' The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods."-" In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba" to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,' were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand-picked quartz, washed free of stains, were reduced in size to —20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This —200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.' The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74-micron quartz particles, using a surface factor of 1.96; is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1953

By Edward Martinez

The reactions occurring in the copper segregation process were studied by heating mixtures of chryso-colla, salt, and a reducing agent. The techniques used in this investigation were differential thermal analysis (DTA) and thermal gravimetric analysis (TGA). The initial chloridizing of the oxide copper occurs below 500°C and cupric chloride may be the compound formed. Volatilization and reduction of the copper chloride take place above 550°C, although these reactions do occur to some extent below 550°C. A difference in the distribution of the metallic copper in the reducing agent was found when sodium chloride was used compared to magnesium or calcium chloride. Segregation was obtained with mixtures of cupric oxide, salt, and charcoal with no quartz or silicate present. Preliminary tests indicate that segregation may occur even in the absence of water vapor. The DTA and TGA techniques were found to be of great value in studying these reactions. The copper segregation process is a method for treating oxide copper ores. The ore is heated, most commonly in a kiln, with a reducing agent and a halide salt, generally sodium chloride, to approximately 700°-750°C and held for 30 to 60 min. The addition of the salt results in the migration and reduction of the oxide copper to metallic copper on the surface of the reducing agent rather than in the original mineral structure. The metallic copper can then be recovered by a subsequent leaching or flotation step.1-4 Experimental work in 1923 on oxide copper ores from the Sagasca mines in Chile led to the discovery of the reduction process. It was found that during the reduction of the copper mineral with coal, at about 700°C, the copper migrated to the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge. The ratio of salt to reducing agent may vary somewhat, but in general 0.5% to 1.5% sodium chloride and 0.5% to 1.0% coal or coke have been mixed with the ore. Less than stoichiometric amounts of salt are required to convert all the oxide copper to a chloride, so that a cycle of reactions appears to be occurring. Several investigations reported in the literature have proposed reactions to explain the mechanism of the process.5-10 There appears to be general agreement that water is necessary for the reactions to occur; that once the sodium chloride reacts with silica or silicates in the ore, the hydrochloric acid formed will convert the cupric oxide in the mineral structure to cuprous chloride. However, there appears to be a conflict of opinion on the reactions involved in the reduction of the cuprous chloride to metallic copper on the surface of the carbon. Rey has indicated that salt, water vapor, and

Jan 1, 1968

By W. J. Rogers, L. J. Dwiggins, R. O. Williams

THERE has been comparatively little work on the importance of strain rate and temperature as variables in the formation of deformation textures. For this reason the present work was started, the choice of compression being in part that of convenience and in part because of the absence of quantitative data in this area. These do not turn out to be important variables within the range studied which permits the results to be condensed into this note. Samples 1/4 in. in diam and 1/2 in. long were machined from 99.9 pct pure commercial aluminum and recrystallized to a fine grain size. A set of five samples were deformed between a spring-driven weight and an anvil resulting in roughly 20 pct strain each time. The strain rate varied because of decle-ration and shortening of the sample but would average about 10&apos; per min. Deformation at temperatures over the range of -76" to 150°C were obtained by heating or cooling the samples. Complete lubrication could be obtained by oil since the short time of contact did not permit its escape. The samples were compressed to a total true strain of 1.4 to 1.6. A larger sample was prepared similarly with spiral grooves in the ends to hold paraffin which provided essentially complete lubrication. This sam ple was compressed slowly at room temperature at a rate of about 2 per min to a total strain of 1.0. Cylindrical samples were carefully machined from these discs with a radial direction as an axis. They came from the center half of the samples and were roughly 1/16 in. in diam. The samples were etched down 15 pct to remove any surface effects. Diffraction data were then obtained for six different kinds of planes by the use of the Norton technique as applied to a fiber texture. Direct comparison between the raw data failed to reveal any significant difference between any of the samples and consequently the data from only one sample was completely reduced. The particular sample had been deformed at O°C The background was subtracted from the intensity data which were averaged over the four quadrants and then normalized to random. These data were then used to obtain fiber-axis distribution charts as previously described.2 For this sample the (422) plane was also run to assist in this inversion. The final result, Fig. 1, provided a comparable fit to that previously obtained from fiber data. About 85 pct of the material forms an elliptical texture around the <110> direction. The radius (at half height) is 5.5 deg along the (111) boundary and 8 deg along the (100) boundary. The remaining 15 pct forms a ridge running from this texture to near the <311> direction. The regions around the (100) and (111) planes are devoid of material. The earlier qualitative results of ~arrett~ are in complete agreement with the present results. The possibility has been dis-cused that the material around the <311> results from friction between the sample and compression plates.4 The present results are considered proof that such is not the case because of the uniformity of sample deformation and the requirement of axial symmetry before fiber-axis distribution charts can be accurately obtained. Recently results have been obtained to show that strain rate and temperature are important variables in the extrusion of aluminum.5 Perhaps the most important observation was that the partial recrystal-lization occurred even at room temperature. Strain rate was considered to be a factor only in that it produced a temperature change. There are many differences between the two experiments, the most important possibly being that their material was roughly ten times the purity of the present material. The present experiment, however, may not be as definitive as desired in this respect since it has been shown that compressed aluminum recrystallizes without a texture change6 although supplementary

Jan 1, 1961

By J. H. Scaff, H. C. Theuerer

Germanium may be reversibly converted from n to p type by heat treatment. Data for the conversion and the associated changes in resistreatment.tivity are given and the results are interpreted in terms of changes in the donor-acceptor balance. MEANS for controlling the electrical properties of germanium in a predictable manner are of interest because of the increasing utilization of this element as the semiconducting material in electrical devices. Since both the mechanism and the magnitude of the electrical conductivity depend upon the kind and quantity of impurities present, the conductivity usually is adjusted by first carefully purifying the germanium, and then, by standard alloying procedures, adding the elements desired. The elements usually added are from the third or fifth periodic groups depending upon whether p- or n-type germanium is desired. However, in the development of germanium rectifiers during the war, it was found that it was possible also to modify reversibly the conductivity of germanium and even to produce conversion from n to p type by heat treatment.1,5 Since then a detailed study of this effect has been made. The data are presented in this paper and an explanation is offered for the effects observed. Preparation and Experimental Procedure The method used in preparing the germanium ingots for this investigation has been previously described.&apos; The method consists essentially of (1) reduction of GeO2* and (2) preparation of a 50-g ingot from the reduced material. Graphite containers are used in both steps. In the first step the GeO2 is reduced in hydrogen at 650 °C to form a sponge germanium which, to assure complete reduction and to obtain massive materials, is fused subsequently in the reduction furnace by gradually raising the temperature to 1000°C. The button of germanium thus obtained corresponds to a yield of 99.8 pct. The final ingot is prepared by fusion of the germanium button in a helium atmosphere. A cylindrical crucible in a vertical silica tube furnace is employed and the crucible is heated by an external induction coil. The ingot is solidified from the bottom upward by raising the induction coil at a constant rate with power to the coil kept at a fixed value. In such ingots, segregation is normal and most of the impurities are concentrated in the last region of the ingot to freeze. It follows then that the major portion of the ingot is purer than it would have been if freezing had occurred in a random fashion. Moreover the orderly advance of the freezing surface during solidification establishes in the ingot a succession of surfaces of constant composition, if it is assumed that the liquid is homogeneous and that diffusion in the solid is negligible. Therefore, some information on the distribution of impurities in the ingot may be acquired by determining the shape of the solid-liquid interface at different stages of solidification. This is of importance because the concentration of impurities will be seen to affect the response of germanium to heat treatment. Such information is difficult to acquire by direct means, for the impurities responsible for the electrical properties of germanium prepared in this way are present

Jan 1, 1952

A. Cook K.A. Grace&apos;s article advocates usage of the terms describing resources as defined by the US Bureau of Mines (USBM) and the US Geological Survey (USGS). Originally recommended in 1943, the terms were revised in 1976 and again in 1980. Mr. Grace further recommends that the term reserves should be severely restricted and that it should encompass mining and processing factors. The list of references quoted in the article does not, however, mention the study concerning reserves that was made over a period of almost four years by a joint Committee on Definitions. This committee was sponsored by three societies - the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the Society of Economic Geologists (SEG), and the American Institute of Professional Geologists (AIPG). Most of the detailed work was done by a working party appointed by the Society of Mining Engineers (SME) of AIME. After studying previous definitions in the US as well as in the United Kingdom, Canada, Australia, France, and other European countries, the following definitions were proposed and accepted in 1974 by the SME board of directors. (Ore reserve definitions in Rhodesia, South Africa, or New Zealand were not mentioned as having been reviewed. Table 1 lists definitions from MINING ENGINEERING, July 1975. Notice in Table 1 it was mentioned, under Resources, that the definitions of reserves were recommended for the purposes of commercial evaluation. It was further stated that the terminology adopted by the USBM and the USGS, as released to the public, covering resources, was recognized as such. Mr. Grace also recommends that reserve calculations should allow for future losses in ore tonnage, ore grade, milling, and smelting. Unfortunately, it might take years to develop a prospect after it has been discovered. Mining methods have to be tested before being finalized in order to know what tonnage of ore is going to be lost, or how much dilution is likely to occur. The same problems are present in concentrating or in smelting. Operating mines usually know how mined grade compares with ore reserve grade. They can usually predict fairly closely what their final metal recoveries are probably going to be. It is, however, expecting too much to have to delay quoting reserves from say a recently drilled prospect. Any responsible mining geologist or mining engineer (or company for that matter) should state several things about an ore reserve calculation: that it is or is not a preliminary estimate only; that estimated grades have not been diluted to allow for a future, as yet unknown, mining method; that metal recoveries are or are not only tentative, based perhaps on drill hole samples only or on no metallurgical testing at all. [ ] Reserves of a partially explored prospect are always quoted when it becomes necessary to raise capital. If they are described as preliminary only (really just tonnage and grade estimates and not true "reserves") in addition to being accompanied by some of the items just mentioned, nobody is going to be misled. If, on the other hand, a report by a member of the SME or SEG is intentionally misleading, the individual must be reported and eventually disbarred from his or her society. To summarize, let us stay with the definitions of ore, ore reserves, and related terms as recommended and accepted by SME. I might add that on occasion I have used a fourth category in my ore reserve calculations, namely Geologically Possible Ore. This category is more or less the same as Inferred ore defined by the USBM and USGS. I have never given a grade to this category, which may be based only on geological mapping, geochemical sampling, or geophysical traversing. ?

Jan 1, 1986

By Irving Cadoff, Richard Nolder

An analysis oj a series of samples of single -crystal silicon grown on sapphire shows that ,four distinct orientation relations exist. There are at least thirteen crystallographic planes which serve as substrates ,for epitaxial growth The model which assumes that silicon substitutes for aluminium and bonds with the oxygen atoms of the sapphire to form the first later for subsequent growth can account for the epitaxial geometry in all four cases. Multiplici-ties 01 specific orientations are found which are explained by the symmetry of both the sapphire and silicon crystal structures. It was reported in the previous paper&apos; that single-crystal silicon films can be deposited on single-crystal a A1,03 (sapphire) with a wide variety of orientations. The silicon films, however, were found to deposit in only four different orientation relationships with respect to the sapphire substrate. The X-ray data have been analyzed to determine the plane and direction of atomic fit and an atomic model to account for the epitaxial relationships at the silicon-sapphire interface has been developed. These results are described in the present paper. EXPERIMENTAL The Laue X-ray data described in the previous paper were reduced to stereographic projections in a standard manner. These data were supplemented with X-ray reflection data obtained with -& E and A Full-Circle Goniometer (Electronics and Alloys, Inc.) mounted on a Phillips diffractometer unit. The silicon films were thin enough to result in characteristic reflections from the substrate as well as the silicon. The superimposed stereographic projections were analyzed to determine the orientation relationships. Ambiguities were resolved by referring to constructed models of various lattice planes for both silicon and sapphire. These lattice models were also used to develop the model for atom fit at the interface. DATA AND ANALYSIS 1) Crystal Structures. The crystallography of silico-n, which is of the diamond cubic class with a. = 5.4~, is straightforward. The sapphire structure is more complex and generally difficult to represent in pictorial form. It is of the rhombohedra1 class but usually referred to hexagonal axes. The transformation of indices between these two systems can lead to ambiguities which will have bearing on the analysis presented herein. Therefore, the basis used in this paper is described in the appendix. Referred to the hexagonal system, the parameters of sapphire are co = 12.95.&, a, = 4.75~, c/a = 2.73. All parameters are for room temperature. Figs. 1 and 2 illustrate schematically the hexagonal unit cell model of sapphire used for this analysis. The oxygen atoms are assumed to occupy positions in an idealized hexagonal array on basal planes. Their actual positions are in a slightly distorted hexagonal array. The aluminum-atom positions are scaled to their actual positions in the lattice with respect to the basal layers of oxygen atoms. It was found that an idealized model where the aluminum atoms are assumed to lie exactly at the octahedral interstices of the oxygen lattice, similar to that used by ~ronberg,&apos; was not adequate for this study.

Jan 1, 1965

By E. H. Bronson

PROPERTY of Malartic Gold Fields Ltd. is situa-ated in the great clay belt in the northern part of the Province of Quebec. This belt represents the floor of the glacial lake Barlow-Ojibway. The clay blanket has a gently rolling, almost flat surface, with here and there projecting knobs and ridges that outline the large irregularities of the surface on which the clay was deposited. At irregular intervals glacial eskers dominate the landscape. The ore-bearing country rock is covered by strata of clay, sand, and silt to a depth varying to 40 ft. There are serious structural problems when it is necessary to place loads of unequal intensities on this surface to support buildings and machinery for a modern mining plant. Earlier mining companies and their engineers paid little attention to the science of soil mechanics, partly because they believed it unnecessary and partly because they knew little of the subject. The results are evident in some of the tottering structures in older camps. Careful analysis of soil problems is well worth-while, since cost of foundations may vary from 20 to 50 pct of the final cost of a structure. Low operating and maintenance costs can be achieved only in this way. If it is definitely established that a plant will be in operation for only a few months, this limited time factor will probably influence the design of the foundation, and rightly so. If sensitive and complickted equipment is to be mounted on these foundations and the plant is to operate for several years, there should be a thorough study of foundations and a very careful design. A familiar problem is presented by the difficulty of operating a permanent plant originally designed for a few months&apos; work. The engineer must beware of these hazards and disassociate himself from them if he cannot prevail on the promoter to spend the proper amount for a thorough foundation study. Laws of certain provinces and states hold the engineer equally responsible with the contractor for any &apos;damage that may be caused to building through inadequate study-ignordnce of the facts is no excuse in the eyes of the law. Types of Soil: The engineer should be familiar with such terms as silt, clay, peat, and varved clay, as well as perpafrost, especially if he is to work in the far northern reaches of the country. He should also be familiar with soil attributes such as porosity, texture, consistency, permeability, compressibility, consolidation, and shearing resistance. The design of any foundation requires an accurate knowledge of the physical properties and location of the soils involved. Older textbooks on the subject outline various empirical methods to determine the carrying power of soil. Tables are given in reference books. The modern ehgineer should be wary of these modes of thinking. He should analyze his problem carefully, calculate to what depth of soil the loads may be transmitted, and then check the bearing value of all soils to that or greater depths. If the strata are water-carrying, he must determine the possibility of this water being accidentally re-

Jan 1, 1958

By Pedro L. Lizaur

INTRODUCTION The degree of success of an association between parties in establishing a new venture ultimately depends on three factors: a. the venture&apos;s underlying economic strength, which is based on the complementarity of the comparative advantages brought by each party to the negotiating table; b. the ability to reach an agreement which satisfies each party&apos;s objectives and constraints; and, c. the capacity to design and implement a funding structure which is consistent with the project economics. A thorough assessment of the venture&apos;s profitability and associated risks under alternative technical and economic scenarios is the basis for a sound "go" or "no go" decision. In-depth evaluation of the risks and rewards to each of the parties involved under alternative legal and financial structure must be the foundation for a long lasting "how to go" decision. The allocation of risks and rewards should be consistent with the objectives and constraints of all parties and the sharing mechanisms, established in the contract, should be flexible to assure the long-term stability of the agreement. Rapidly changing economic conditions during the last decade have had a dramatic impact on the envisaged allocation of risks and rewards between host countries and private investors. The effects of these changes, and the fact that the relative strengths of the parties involved may shift during the life of a project (e.g. before and after major capital investments have been made), have forced the renegotiation of a multitude of contracts. Therefore, the present and future stability of an economic agreement would depend not only on the originally designed provisions, but also on provisions which allow for the automatic adjustment of rewards to project sponsors under a variety of future economic situations. A pre-condition for the allocation and quantification of risks and rewards is the definition of standards of measurement used by each of the parties. This is critical in international negotiations when one of the parties represents the national interests of a country. The understanding and use of different standards for the measurement of rewards for risk taken between a government and private enterprise facilitate the negotiation of a satisfactory agreement. This is possible because certain trade-offs between the negotiating parties may have different relative values. STANDARDS OF MEASUREMENT OF REWARDS FOR RISK TAKEN The negotiating process takes a step forward when the parties are able to focus on their interests, explore different alternative solutions and then base results on a set of objective standards. Unfortunately, the parties frequently put more effort into "staking out" and defending positions, than into understanding their intrinsic interests. Moreover, when one party, such as a governemnt owned corporation, represents a country&apos;s national interests, the negotiation process increases in complexity. Private firms focus on commercial profitability, using discounted cash flow techniques such as NPV, IRR, or ROE. In contrast, the government is also concerned with the project&apos;s impact on the local socio-economic environment. Without entering into a discussion of alternative economic development theories and approaches, there exist several possible measures that could be pragmatically utilized by each party in evaluating the socio-economic impact of a project. The more complete measure is the National Profitability (NP). The NP is a discounted cash flow procedure similar in structure to IRR or NPV but in which the project&apos;s financial cash inflows and outflows and discount rates are adjusted to take into consideration the local conditions. The NP is calculated on an unlevered basis and all taxes and duties are removed from the project

Jan 1, 1985

By L. W. Sink, B. H. Kear, S. M. Copley, M. F. Hornbecker

IT is well known that under appropriate conditions of chill casting, many metals and alloys develop a columnar grain structure having a high degree of preferred orientation.&apos; In cubic materials, this principle has been employed to produce shaped castings with a unidirectional cube oriented columnar grain structure as well as shaped single crystals with a cube axis parallel to the growth ais.&apos; "he purpose of this note is to describe how this same principle can be enlployed to produce wires, rods, or more complex crystal Shapes with a variety of conlpositions in cube or random orientations by a single casting operation. The procedure for directional solidification of in Fig. 2. Examination under crossed polarizers indicated that the striations were a second phase (presumably the B19 phase) which frequently forms initially at primary grain boundaries and then grows toward the interior as thin ribbons. X-ray studies on filings of this alloy reannealed at 1300°C for 15 min indicated a strong pattern of the fcc phase together with a substantial pattern of the B19 phase. The un-annealed filings, however, showed only the pattern of a cold-worked, fcc structure. In these two-phase alloys it appears, therefore, that the B19 phase is transformed into a disordered fcc structure by cold-working. The mechanical properties of these alloys would be of some interest since a fcc structure might be expected to possess greater ductility than the or-thorhombic B19 structure from which it forms. The author wishes to thank Mr. Harvey Yakowitz and Mr. Richard Manuszewski for obtaining the photomicrograph in Fig. 2. This research was partially supported by Research Grant DE-02455 from the National Institute of Dental Research. columnar grained ingots involves pouring a melt into a preheated mold having a water-cooled copper chill at its base? and controlling the temperature gradient in the mold so as to maintain columnar grain growth from end to end of the ingot.4 This is illustrated schematically in Fig. l(a). It should be noted that the longitudinal temperature gradient promoting unidirectional columnar grain growth is maintained by heat loss primarily through the solidifying ingot to the chill, so that both the temperature gradient and the growth rate diminish with increasing distance from the chill. As the distance from the chill increases? the columnar structure coarsens, and the perfection in preferred orientation tends to increase progressively. Using this same procedure of gradient solidification, Fig. l(b) shows a simple scheme for producing a batch of crystals having the same cube orientation rather than an assemblage of columnar grains. Wires and rods are produced by cementing ceramic tubes to the wall of the mold. The steep temperature gradient produced in the central chamber is controlled by the mold heater to produce favorable conditions for crystal growth. Clearly the success of the operation lies in the selection of individual growing columnar grains by some kind of orifice at the base of each channel in the mold. Using simple constrictions, experience with nickel-base alloys has shown that 4 -in.-diam holes at a distance of -1 in. from the chill yield crystals within 7 deg of (100); closer control of orientation is possible by placing the crystal selector farther away from the chill.

Jan 1, 1970

By Richard R. Zupp, David A. Stevenson

A theoretical treatment of austenitic Fe-C-Z solutions (where Z represents a substitutional solute) was developed by extending a solution model which was previously applied to austenitic Fe-C alloys. The model assumes that each carbon atom in the solution excludes H interstitial sites from occupancy by other carbon atoms rmd thai otherwise the assembly of carbon atoms is equivalent to a modified Langmuir lattice gas. The results of the treatment provide theoretical justification for a phenomenological expression previously developed to represent the influence of substitutional solutes on the thernlodynamics of carbon in austenitic Fe-C-Z alloys. The expression is: where Kz is a parameter which characterizes the Fe-C-Z system at a given temperature and Xz and xj are the concentrations of substitutional solute and interstitial carbon expressed as atom ratios. The parameter, Kz, was associated with the differ- A number of investigators have measured the influence of various substitutional solutes on the carbon activity in austenitic Fe-C-Z alloys, where Z represents any substitutional solute. Experimental information is available for alloys containing the following substitutional solutes: Mn,&apos; Si,&apos; Ni,2-5 CO,&apos;-&apos;, Cr,5, 9-11 CU,4 Al,= v,11, 12 and Ti.13 This information is essential for studying many phenomena in Fe-C-Z alloys, particularly diffusion and diffusion-controlled phase transformations For example the pffprts nf various ence between the interaction energies between carbon atorns and host-lattice atoms in the Fe-C-Z solution and the corresponding energies for the Fe-C solution. The carbon activity in a ternary Fe-C-Z alloy, ac, was obtained in terms of the composition of the alloy and the single parameter, Kz: where y° is the Henry&apos;s law constant for the binary Fe-C solution. Both y° and H crm be determined from the data for Fe-C solutions, without recourse to any experimental data for Fe-C-Z solutions. The theoretical treatment was extended to alloys containing several substitutional solutes. By neglecting interactions between the substitutional solutes, an expression for the carbon activity in multicomponent alloys was obtained in terms of the Kz values characterizing ternary Fe-C-Z systems. substitutional solutes on the rate of pearlite growth is explained14 on the basis of their effects on carbon diffusion, which result from their influences on the carbon activity in the solid phases. In addition, recent studies have emphasized the dependence of the pro-eutectoid ferrite transformation15 and other diffusional processes in austenite16 on the influence of substitutional solutes on the carbon activity in austenite. They have indicated the need for suitable analytical expressions to represent such influences. The present authors previously developed general phenomenological expressions to represent the equilibrium partitioning of carbon between Fe-C alloys and Fe-C-Z alloys.&apos;2 The expressions are applicable to all the austenitic Fe-C-Z alloys for which experimental data are available, and are sufficiently simple to recommend their general application. For alloys in

Jan 1, 1969

By Irwin R. Higgins

CONTENTS A. Introduction B. System Description C. Uranium Pilot Plant Programs D. Summary INTRODUCTION The Chem-Seps Continuous Countercurrent Ion Exchange (CCIX) contactor was first conceived of in 1951 at the Oak Ridge National Laboratory. In the 27 years that have passed, there has been a steady stream of pilot plant process development studies on a variety of processes far too numerous to mention. These have been in the area of water and waste treatment, chemical processing, ore leach treatment, and many others. Many successful production systems have been installed and operated in a variety of applications. A few of these are described herein together with a description of the system and its operational characteristics. SYSTEM DESCRIPTION Chem-Seps Continuous Countercurrent Ion Exchange* is a single loop in which various sections are separated by valves to isolate the sections performing different functions simultaneously. (Refer to Figure 1). To explain the working of a typical unit, let us use a simple configuration used in water softening or demineralization. The resin is moved in small increments by the hydraulic ram action. All solution flows are countercurrent to the flow of resin. The contaminants are removed in the process cycle and the resin is moved in the pulse cycle. A controller in the effluent stream from the treatment section senses the proper limit permissible in the effluent. In the process cycle, the influent enters through a set of distributors, moves downward and leaves through a set of collectors. Simultaneously the regenerant enters through valve RE and leaves through valve WA. The rinse enters through valve RI and its duration is controlled by an interface controller. In the process cycle, valves B, C, and D are closed, isolating all the sections. The duration of the process cycle is 4-10 minutes depending on the contaminants to be removed and is controlled either by a timer if the contaminants are fixed, or a controller in the effluent stream, if the contaminants fluctuate at short intervals. Valve A is open and resin is dropped to the pulse section simultaneously with the removal of contaminants in the treatment section, regeneration of loaded resin in the strip section, and rinsing of regenerated resin in the rinse section. As the resin drops through the valve A, it is backwashed to remove the suspended solids or resin fines. Removal of these fine particles is important to avoid the unnecessary pressure drop in the bed and plugging of the distributors. At the end of process cycle, all flows going into the unit and out of unit are automatically shut off. The valve A closes and valves B, C, and D open in proper sequence. A slug of water enters through valve PU, a predetermined incremental volume of resin moves into the regeneration section, an equal volume of regenerated and rinsed resin enters the bottom of the treatment section, and an equal volume of the loaded resin leaves the top of the treatment section and goes into the resin reservoir section. (The resin movement is plug flow with the Reynold&apos;s number being in the laminar region of the curve, and no fluidization occurs during the pulse cycle.) The total time required for proper sequencing of valves and the movement of resin is 20-30 seconds. At the end of this period, the valves B, C, and D close and valve A opens. The solution valves open and normal steady state operation begins. All valves are interlocked and properly sequenced. The resin movement is precisely controlled by sonic devices. Special Features of Chem-Seps CIIX "Downflow"*: The raw feed in the treatment section moves downward and the resin moves upward in the treatment section. The "downflow" of feed overcomes the handicap encountered in "upflow" systems. The "upflow" of feed requires a certain minimum flux during process cycle to lift the bed and keep it

Jan 1, 1979

By A. M. Gaudin, C. S. Chang

Adsorption was measured for barium ion and laurate radical, using radioactively marked agents, over wide range of concentrations. Laurate adsorbed in absence of barium fails to float. With barium, flotation-effective laurate coating needs not exceed 5 pct of monolayer. Barium adsorption then is several fold larger. No barium laurate coating is obtained. IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.&apos;-&apos; The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods."-" In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba" to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,&apos; were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand-picked quartz, washed free of stains, were reduced in size to —20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This —200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.&apos; The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74-micron quartz particles, using a surface factor of 1.96; is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1953

By Zay, Jeffries

THE effect of thoria (ThO2) on grain growth in tungsten was discussed in some detail in a paper presented before this Institute by one, of the authors in 1918.1 In that paper it " was assumed that the, thoria was present in the tungsten entirely as a mechanical mixture. There was no indication in the experiments described that even a trace of the thoria was in solid solution in the tungsten. Langmuir,2 however, observed that thoriated-tungsten filaments under certain conditions showed electron emissions many thousand times greater than unthoriated tungsten at the same temperature. He concluded from his studies that a slight amount of the thoria had dissociated on heating the filament to a temperature near 220°. C. At this temperature and higher, part of the thorium diffuses to the surface of the filament where it evaporates at. a much faster rate relatively, than the tungsten, and also at a rate, nearly as fast as it is brought to the surface by diffusion: If the temperature is lowered to say 1800°,. C., diffusion of the thorium atoms to the surface is more rapid than evaporation, sown adsorbed film of thorium atoms is produced on the surface of the tungsten filament. The electron emission is governed by the outside layer of atoms so the emission from such a filament might be expected to approxi¬mate that of a thorium filament at the same temperature. PRESENCE OF METALLIC THORIUM IN THORIATED TUNGSTEN If the filament containing the adsorbed film of thorium. is heated to a sufficiently high temperature, the thorium atoms evaporate: rapidly and the electron emission becomes more nearly that of tungsten. On cooling again to 1800° C., or thereabouts, the emission &apos;builds up gradually to a maximum. The filament containing the adsorbed layer of thorium atoms is said to be "activated." By studying the rates of activation under different conditions of prior thermal treatment and at different temperatures, Langmuir was able to arrive at an estimate of the

Jan 1, 1927

By T. M Morris

THE rate of flotation of solid particles determines the percentage recovery of these particles which can be obtained during a given time interval. It is an established fact that the recovery is greatest in the fine sand size range and falls off on either side of this size range. It is also a fact that the history of the development of concentrating devices has been marked by a desire to recover the small particles: tables were developed to treat material too fine to recover in jigs; flotation recovers material too fine to be recovered on tables. As our ores become more complex and require finer grinding, a greater proportion is in the slow-floating size range. It is therefore of economic importance that the effect of size of particle upon rate of flotation be studied. Many studies have been made along this line. The present investigation attempts to quantify the rate of flotation by means of a rate equation, and then compares the effect of size upon the rate of flotation. It was found that the flotation rate constant increases with increase in diameter of particle in the size range smaller than the optimum size particle. The flotation rate constant decreases with an increase in diameter of particle in the size range coarser than the optimum size particle. This suggested two different actions taking place, and these are discussed. Suggestions for further work in order to improve the flotation rate of both fine and coarse particles are made. The usual method of expressing rate is to plot cumulative percent recovery vs time. If we knew the equation of this kind of curve we could replot it as a straight line, and the slope of the line would be an index of the magnitude of the flotation rate. It is easier to compare straight lines than curves. The basis used for obtaining the equation of the recovery vs time curve is the law of mass action. This law states that the "rate of a chemical reaction is proportional to the &apos;active masses&apos; of the reacting substances present at any given time." This, of course, implies a constant temperature. We can modify this for our use by using the term flotation reaction instead of chemical reaction and the term floatable particle instead of active masses. dC Thus----— kc [1] where C denotes concentration of particles, t denotes time, k denotes a proportionality constant. If the exponent of C is 1, then we have a first order rate reaction. If the exponent of C is 2, then we have a second order rate reaction. For a first order rate reaction, we obtain, after integration, where k is again a proportionality constant and has the dimension of the reciprocal of time. C, is the original concentration or weight or percentage of floatable particles. C, is the concentration or weight or percentage of floatable particles remaining in the flotation cell after time t. If all particles of the mineral to be floated were capable of floating we could take C, as 100 and C, would be 100 - R, where R is the cumulative percentage recovery of mineral at time t. But it is not usual for all of the particles to be capable of floating, because of surface oxidation, etc. Therefore, we must introduce a factor x which is the percentage of un-floatable mineral. Hence the first order equation is It has been proposed by various workers1-&apos; that this equation describes the flotation rate. More recently N. Arbiter4 states that a second order rate equation fits the recovery vs time curve more closely than does a first order rate equation. Morris- as discussed the evidence presented for this statement. It has been concluded that the first

Jan 1, 1953

By W. L. Phillips

Single crystals of aluminum, brass, and copper oriented for (100) and (110) slip were extended at 25°, 400°, and 600°C in simple shear. Aluminum specimens oriented for nonoctahedral slip began to shear at a higher critical resolved shear stress than specimens oriented for octahedral slip. Parabolic stress-strain curves were obtained from zero strain. The initial rate of parabolic hardening was lower for specimens sheared on the (100) plane in a close-packed direction <110>, than for specimens sheared in a nonclose-packed direction <100>. metallographic evidence, however, showed that all slip traces could be explained in terms of (111) <100> slip. All attempts to cause nonoctahedral slip in copper and 70-30 a-brass single crystals were unsuccessful. Instead of shearing, the crystals bent, allowing {111} type planes to come into action. NONOCTAHEDRAL slip in aluminum has been reported under three different conditions: first, as the main mode of slip in tension experiments at elevated temperatures;&apos;-&apos; second, as the main mode of slip in direct shear experiments at room temperat~re; and third, as a minor mode of deformation, i.e., as cross-slip, in tension, shear, and bicrystal experiments at room and elevated temperatures."-l2 However, as far as the author knows, nonoctahedral slip has not been reported in either copper or 70-30 a-brass. The present study was undertaken to determine whether nonoctahedral slip could be obtained in aluminum, brass, or copper at room or elevated temperatures when the shear stress was approximately constant over the cross-section, a maximum at the center, or a maximum at the surface. EXPERIMENTAL PROCEDURE A detailed description of the crystal preparation and shearing apparatus has been given previo~sly. Cylindrical crystals 1/2 in. in diam and 8 in. long were grown from the melt in a temperature-gradient furnace. The aluminum contained 0.001 pct Zn, 0.001 pct S, and 0.001 pct Fe; the 70-30 brass contained 0.015 pct Pb, 0.001 pct Fe, 0.01 pct Ni, 0.02 pct Sn, and 0.005 pct Se; the copper was certified OFHC of 99.98 pct purity. All samples were electropolished prior to testing. The shear apparatus was a modified Bausch type. The strain sensitivity was 4 x lob4 Load was applied by clamping the rods attached to the shear plates in an Instron tensile machine. The rate of loading was 0.02 in. per min. In all cases a 1/8-in. gage length was used. For the tests performed at 400° and 600°C the shear plates, collars, and rods were made of stainless steel. These elevated-temperature tests were performed in an argon atmosphere. A) Aluminum at Room Temperature. Values of a and ß for the various slip planes and slip directions investigated are shown in Table I where a is the complement of the angle between the specimen axis and the slip direction, and ß is the angle between the specimen axis and the normal to the shear plane. The shear stress is a function of a (assuming ß - 0);10 when a is less than 27 deg, the shear stress on the slip plane for which the specimen is oriented has a maximum at the center of the crystal; at a = 27 deg the shear stress is constant across the slip plane; for a greater than 27 deg the shear stress is a minimum at the center. Fig. 1 shows the stress-strain curves for specimens cut from crystals 1, 2, and 5, which were sheared on the (010) plane in the [loll direction at room temperature. These three crystals have shear-stress distributions corresponding to the three dif-

Jan 1, 1962

By Larry Kaufman

A useful method for estimating the entropy of NaCl type compounds has been developed by combining the Debye theory of specific heat with the Lindemann formula. This method pemnits calculation of the entropy from a knowledge of the atomic weight, atomic volume, and melting point of the compound. Comparison of the calculated and observed entropies of 35 NaCl type compounds over a wide temperature range yields good agreement thus establishing the usefulness of the method. Application of the method to other crystal types is also discussed. KUBASCHEWSKI~ has suggested a useful method of estimating the enthalpy of formation of inter-metallic compounds from a knowledge of the crystal structure, lattice parameter, and heats of sublimation of the component elements. This method is quite valuable in predicting the tendency for compound formation in a given system and is of particular value in considering systems for which no experimental data are available. In order to supplement the enthalpy calculation afforded by Kubschewski&apos;s method, it would be of value to be able to estimate the entropy of compounds so that the entropy and free energy of formation could be evaluated. Although a considerable body of such data determined by calorimetric and equilibration techniques exists at present, the difficulty of making such measurements (particularly at high temperatures) and the ever increasing number of new compounds which are of interest make the desirability of such a computational method clear. This paper deals with a method for calculating the entropy of a compound from a knowledge of the atomic weight, atomic volume, and melting point. Since these data are generally easier to determine and therefore more readily available than thermo-dynamic data, they should provide an additional tool in estimating the stability and reactivity of compounds at high temperatures. I) THE ENTROPY OF PURE METALS As a first approximation, the specific heat of a pure metal can be represented by a sum of terms where C,($/tI is the vibrational specific heat calculated on the basis of the Debye theory, lo4 TC, (0/T) is an approximation to the Cp - C, correction. T is the electronic specific heat, and Cp (p) is the magnetic specific heat. Although the Debye theory does not provide a complete description of the vibrational specific heat, i.e., the Debye temperature 0 is not a constant, it does provide a good approximation when used properly. Blackman6&apos;7 has written several reviews on this subject discussing the different values of 0 determined by various methods (specific heat, X-rays, elastic constants, electrical resistivity, and so forth), as well as the observed temperature dependence of 0 with T. In the present case the 0 in Eq. [I] naturally refers to the specific heat 0. The variation of Debye 0 (as determined from specific heat measurements) with temperature is observed to exhibit its most radical behavior at very low temperatures. At higher temperatures the 8 values are observed to become more nearly constant. Blackman6&apos;7 has presented the variation of 0 with temperature for several metals. His tabulation is reproduced in Table I. Reference to Table I shows that above a certain temperature level, 0 remains fairly constant. The value of 0 which is most useful in computing the specific heat, and hence the entropy, is the value of 0 in the range 0/6 « T « 0. In 1910, Lindemann&apos; suggested a relation for estimating Debye 0 values. According to this formula, where V is the atomic volume, T is the melting point in &apos;K, M is the atomic weight, and CL is a constant. Mott and Jones9 present this formula and state that there is at present no satisfactory theoretical explanation, but that it does have an empirical basis. By using the valuesof 0 in Table I along with known1&apos; values of M, T, and the molar volume VM, where the Lindemann constant can be evaluated. This

Jan 1, 1962

By H. E. Cline

A criterion for stability of a lamellar structure in two-phase alloys ulas derived froflr perturbation analysis of the steady-state solutions for eutectic growth. Both the mass and thermal diffusion were considered with boundary conditions for coupled lamellar growth. The concept of an effective liquidus slope was introduced. Excellent agreement was found with the experiments of Mollard and Flemings and the theory predicted a range of compositions on one side of the eulectic composition in which stable growth may occur with zero temperature gradient. The lamellar structure was found to be more stable than predicted by simple constitutional supercooling. The effect of impurity additions was also considered. DIRECTIONALLY solidified eutectic alloys may have a structure consisting of parallel plates or rods. It is important to know the range of composition and growth conditions that produce this ideal composite structure. Breakdown of the planar solid-liquid interface during growth may lead to a dendritic or cellular structure as in single-phase alloys. In the case of single-phase alloys, the concept of constitutional supercooling1 may explain breakdown, but in two-phase alloys the concept is no longer valid because the melting point is not given by the liquidus of one phase. Both phases must be considered in the mass and thermal diffusion problem. In the following theory a boundary condition at the solid-liquid interface was determined by using the steady-state equations of Jackson and ~unt&apos; to relate the average temperature and composition of the liquid at the interface. Then a sinusoidal perturbation in the shape of the interface was introduced to test for stability as in the analysis of Mullins and ~ekerka.~ The wavelength of the important perturbation was assumed to be much larger than the lamellar spacing, h, and the perturbation was assumed not to change the lamellar spacing, A. Both the mass and thermal diffusion equation were used with averaged quantities at the boundary to determine whether the perturbation grows or shrinks in time. A stability criterion was determined by considering the case in which the perturbation remains stationary. An example of Pb-Sn alloys was used to illustrate the validity of this theory. I) THEORY A) Temperature at the Interface. The temperature of the interface in coupled two-phase growth is close to the eutectic temperature TE even for alloys off eutectic composition. It is assumed that the interface is in local equilibrium and one expects the temperature at the intersection of the liquid phase and the solid phases a and 0 to be near the eutectic temperature. The interface is undercooled because of curvature and the deviation of the composition in the liquid from the eutectic composition. The average interface temperature Ti for steady-state growth of a lamellar eutectic with a plane interface was determined by Jackson and Hunt&apos; as given in their Eq. [17c]. Instead of using the ratio of the lamellar widths hp/h, as a parameter, the volume fraction of the 0 phase, +, will be used as it simplifies the algebra. The average interface temperature using this notation becomes: The average temperature of the interface depends on the volume fraction of the 0 phase, +, which may be related to the composition of the solid or the bulk composition of the liquid Co by: where C, and Cp are the average compositions of the solid phases. In steady-state growth, the composition of the solid is equal to the composition in the liquid far from the interface. The variation of the average interface temperature with composition is illustrated in Fig. 1 for the case of Pb-Sn alloys with a 10"4 cm lamellar spacing as calculated from Eqs. [I] and [2]. The interface temperature goes through a maximum at a composition near but not exactly at the eutectic composition. There is no reason why the composition corresponding to the maximum temperature should be equal to the eutectic

Jan 1, 1969

By P. M. Blair

This paper presents numerical solutions of the equations describing the imbibition of water and the countercurrent flow of oil in porous rocks. The imbibition process is of practical importance in recovering oil from heterogeneous formations and has been studied principally by experimental means. Calculations were made for imbibition of water into both linear and radial systems. Imbibition in the linear systems was allowed to take place through one open, or permeable, face of the porous medium studied. ln the radial system, water was imbibed inward from the outer radius. The effects on rate of imbibition of varying the capillary pressure and relative permeability curves, oil viscosity and the initial water saturation were computed. For each case studied, the rate of water imbibition and the saturation and pressure profiles were calculated as functions of time. The results of these calculations indicate that, for the porous medium studied, the time required to imbibe a fixed volume of water of a certain viscosity is approximately proportional to the square root of the viscosity of the reservoir oil whenever the oil viscosity is greater than the water viscosity. Results are also presented illustrating the effects on rate of imbibition of the other variables studied. INTRODUCTION The process of imbibition, or spontaneous flow of fluids in porous media under the influence of capillary pressure gradients, occurs wherever there exist in permeable rock capillary pressure gradients which are not exactly balanced by opposing pressure gradients (such as those resulting from the influence of gravity). The importance of such capillary movement in the displacement of oil by water or gas was recognized in early investigations and described by Leverett, Lewis and True in 1942.1 Methods advanced by these authors for studying the process using dynamically scaled models were rendered more general and flexible by the research of later workers.2"4 The influence of capillary forces in laboratory water floods has also been discussed by several authors.6 While imbibition plays a very important role in the recovery of oil from normal reservoirs, Brownscombe and Dyes7 pointed out that imbibition might be the dominant displacement process in water flooding reservoirs characterized by drastic variations in permeability, such as in fractured-matrix reservoirs. In water-wet, fractured-matrix reservoirs, water will be imbibed from fractures into the matrix with a countercurrent expulsion of oil into the fractures. If the imbibition occurs at a sufficiently rapid rate, a very successful water flood can result; if the imbibition proceeds slowly the project might not be economically attractive. Scaled-model studies have demonstrated the vital importance of imbibition in secondary recovery in fractured reservoirs. It is therefore important in the evaluation of waterflooding prospects to develop a thorough understanding of the quantitative relationships of the factors which control the rapidity of capillary imbibition. The imbibition process serves reservoir engineers in still another important way by providing a technique for studying the wettability of reservoir core samples. Such experiments are usually conducted by observing the rate of expulsion of oil or water from core samples submerged in the appropriate fluid. Several papers have been &apos;published on the experimental techniques involved?? Although Handy has recently published a method for calculating capillary pressures from experiments with gas-saturated cores, it has not yet been possible to deduce quantitative information regarding water-oil relative permeability and capillary pressure characteristics of the rock from the experimental results. Thus a technique is needed for studying the quantitative dependence of imbibition rate on oil and water viscosity, initial water saturation, relative permeability-saturation, and capillary pressure-saturation relations. The development of such information, including saturation and pressure profiles by laboratory experiments, would be very difficult. However, recent advances in the applica-

Jan 1, 1965

By J. H. Rushton, L. H. Mahony

Principles of fluid motion and turbulence which have been found to be of use in mixing and agitation problems are discussed, as well as suggested applications in extractive-metallurgy processes. Various types of impellers are described, together with other conditions that affect flow pattern and turbulence. The choice of equipment for particular requirements is considered, and equations for power input are given. Modern heavy-duty mixing and agitation equipment can take an increasingly important part in such extractive-metallurgy processes as solids handling, crystallizing and leaching, chemical operations, and flotation. Application of mixing and fluid-mechanics principles to extraction methods can lead to greater process rates and a resultant saving in time and money. MIXERS are being applied with increasing frequency to problems in the metallurgical industries. The increase represents in part the modernization of mechanical equipment used through the application of unitized drives, modern electric motors and speed reducers, and recently developed materials of construction. Some applications have resulted from process changes and the use of techniques for operations similar to those that have been demonstrated and proven in the chemical industry. Still more applications are being developed through the use of fluid-dynamics principles not previously recognized as applicable to these operations. It is the purpose of this paper to describe those principles of fluid motion and turbulence which have been found to be of use in mixing and agitation problems, and to suggest applications for them in the extractive-metallurgy processes. Modern mixing equipment has been designed to provide the fluid motion consistent with that best suited to different operations.&apos; When properly applied, these more efficient fluid-handling mixers result in lower process-production costs. Metallurgical operations usually involve large amounts of solids. The characteristics of the ore control the process and only enough liquid is added to provide sufficient fluidity for handling and processing. The reactive part of the ore, the mineral value to be extracted, is likely to be low in percentage, and the quantity of reagent required is similarly low, but excessive dilution makes additional reagent necessary and therefore is undesirable. Thus, the primary problems in minerals processing are to handle as high a concentration of solids as possible and to distribute reagents uniformly. These pulps, or slurries, are in a range of solids concentration where hindered settling rates apply, and care must be taken to agitate and mix sufficiently to maintain suspension and flow throughout the equipment. Such slurries have high densities which are the weighted average of the components and viscosities that are spoken of as "effective viscosities" but are difficult to evaluate. It is convenient to separate metallurgical operations involving mixers and agitators into three categories: solids handling, mechanical or physical operations, and chemical operations. In each of these categories fluid motion is required to maintain suspension, to distribute surface-active agents, to blend components and reactants, and to induce high rates of chemical reaction. After a discussion of some basic principles of mixing and agitation, examples of application to the three categories will follow. Fluid Motion The fundamental problems of mixing and agitation of liquids have to do with the mechanics of fluid streams and the means by which they are

Jan 1, 1955

By L. W. Pommier, F. B. Brien

The Rheological properties of pulps are non-Newtonian in character and more than one viscosity parameter is necessary to describe their behavior, therefore, the single term &apos;apparent viscosity&apos; which has been used in the past may be misleading. The study reported in this paper uses a dimensional analysis based on the Ostwald-de Waele shear stress-rate of shear model for non-Newtonian liquids to develop velocity and resistance equations for falling spheres. An electronic monitoring apparatus was assembled for determining the velocity of metallic bodies as they fall through opaque liquids and suspensions. By means of this apparatus the behavior of the viscosity parameters of the Ostwald-de Waele model and the applicability of the proposed equations were examined for a number of non-Newtonian liquids. The validity of the equations for these liquids was confirmed. Preliminary data collected using solid-liquid suspensions established the validity of the form of the basic equations for these systems. The differential movement of solid particles through solid-liquid pulps and suspensions is very important LO many branches of engineering, such as minerals processing, soil mechanics, ceramic slip processing, oil well drilling-mud technology, materials-handling in pipelines, and many others. There is a dearth of fundamental knowledge on the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The resistance offered by Newtonian liquids to the movement of free settling spheres is well described for laminar and turbulent conditions by Stokes&apos; and Newton&apos;s Laws, respectively. However, problems are encountered when attempts are made to extrapolate these simple relationships into solid liquid suspensions. The rheological properties of pulps are such that they are non-Newtonian in character;&apos;" that is, the applied shearing stress and resulting rate-of-shear are related by non-linear functions, and thus, in the simplest case two viscosity parameters are necessary to describe their rheological properties. For this reason the single term &apos;apparent viscosity&apos; which has been commonly used to explain the flow resistance of suspensions and non-Newtonian liquids may be misleading. It is realized that a rigorous analysis of the rnechanisms of momentum transport of liquid-solid systems is complex indeed. There are many variables that affect the rheological properties of the systems such as density, size, shape, and surface energy of the suspended solid and density and viscosity of suspending liquid, as well as the solid to liquid ratio. However, it was felt that a useful contribution to the knowledge of the behavior of suspensions could be made by examining the systems in terms of the basic fundamentals of nowNewtonian flow. This has led to the development, by means of dimensional analysis, of velocity and resistance equations, using two viscosity parameters to describe the velocity of penetrating bodies and the flow resistance encountered by these bodies, as they pass through non-Newtonian systems. THEORY In order to examine the effects of the rheological properties of solid-liquid suspensions on the movement of immersed bodies it is appropriate to start with non-Newtonian liquids and develop equations, analogous to those of Stokes and Newton, for laminar and turbulent flow respectively, from which quantitative information may be obtained. Further investigation would then be directed at the complex suspension systems, and the effects of the many variables on the velocity and resistance equations. Liquids are classified on a basis of viscosity which may be defined as the relationship between applied shear stress and resulting rate of shear?-&apos;* Pure single phase liquids composed of small light molecules behave as Newtonian liquids, having a single viscosity parameter since the shearing stress and rate-of-shear are related by a linear function. Bingham plastics are similar but have a yield stress. Of particular importance in our investigation are dilatant (shear thickening) and pseudoplastic (shear thinning) non-Newtonian liquids, with and without yield values.

Jan 1, 1968