Search Documents

By W. T. Nightingale

The three gas-producing "pools" discussed in this paper are in Sweet-water County, southwest Wyoming, and Moffat, County, northwest Colorado. Hiawatha, North Baxter Basin and South Baxter Basin gas fields became economically important in 1929 when a 330-mile gas line connected them with Salt Lake City, Ogden and towns en route. This development immediately focussed attention on the gas-producing fields and the efforts of the producing company to develop them in an orderly, economical manner. Several outstanding interests were acquired and working agreements made with others. Thus the interference of natural drainage areas was avoided, the pernicious practice of drilling direct

Jan 1, 1930

By John F. Havard, Armine F. Banfield

Sooner or later, we all get involved in the economic study and valuation of a mineral deposit. To communicate clearly the necessary information, we must scrupulously use various terms with specific meaning. All these terms-such as ore, exploration, development, production, reserves, proven ore, probable ore, possible reserves, resources, as well as similar terms applying to coal-are continually on the lips of anyone who reports on the economic aspects of a mineral deposit at the exploration, development, and production stages. The meaning of these terms is even more important in feasibility studies to determine whether a deposit should be put into production. Finally, careless use of these terms in reports published for public financing may, and sometimes does, lead to prosecution of the writer for misleading information.

Jan 7, 1975

By G. Hergert

SUMMARY Three gradients have been identified in regard to the average horizontal ground stress increase with depth. [S (0-900 m) = 9.86 MPa + 0.0371 MPa/m SHa (900-2200 m) = 33.41 MPa + 0.0111 MPa/m SHae (extreme)= 12.36 MPa + 0.0586 MPa/m] The extreme stress values are not caused by mining geometry and are of limited extent only. In some cases geological disturbances like faults and rock type boundaries suggest an explanation but in other cases the unusually high stresses cannot be explained readily. It is interesting to note that in the same locations the vertical stress components are very much higher than those derived from overburden weight and that the vertical stress gradient is similar to the gradient obtained from the extreme horizontal stress components. INTRODUCTION Ground stress determinations have been carried out in mines in Ontario and Manitoba, Canada, over more than a decade (Herget, 1980). Most of the sites are located in the Superior and Southern Tectonic Province of the Canadian Shield, which consist of Archaen and Proterozoic rocks comprising volcanics, metamorphosed sediments and granites. The youngest orogenic deformation occurred during the Grenville Orogeny (955 million years ago).

Jan 1, 1982

By T. Okubo

Gold is generally recovered from silver anode slime by electrolysis in the final step of the copper anode slime treatment. In the present investigation, rapid and direct hydrometallurgical separation and recovery of gold in the early step of the process is studied. Gold is recovered just after the elimination of copper and selenium from copper anode slime. The studied process consists of: (a) oxidizing roasting for selenium elimination, (b) sulfuric acid leaching of the calcine for copper removal, reduction of gold in the liquor by the use of proper reductant such as hydrogen peroxide (production of gold powder), (el nitric acid treatment of gold powder for further purification and (f) melting and casting of gold. Laboratory and miniplant testwork showed that the extraction ratio of gold by chlorine leaching was 99 % up and four nine gold ingot could be recovered without electrolyses.

Jan 1, 1984

By D. H. Gieskieng

THE advent of curved jaw crusher wearing plates made an approach other than segmental layout analysis desirable for prediction of capacities. For some time it had been known that the drawing board capacities of crushers using these plates had to be considerably modified by complicated experience factors to achieve agreement with results. Because these apparent capacities could be readily increased severalfold by minor crushing chamber shape changes, it was necessary that the utmost precaution be taken in predicting capacities of jaw plates modified for nonchoking, special wear characteristics, or any other reason. To this end the laboratory and field tests outlined by the author in a previous paper' were made on Blake-type jaw crushers. The results of these tests were summarized in a simple first degree equation applicable to crushers using either straight or curved jaw plates. This equation first outlines the maximum capacity potential of a given crusher, then reduces this figure in accordance with installation circumstances by means of a realization factor.

Jan 11, 1951

It is too late to gloat over the fact that minerals have furnished 67 per cent of the primary wealth of Pennsylvania. It is high time that Pennsylvanians do some constructive thinking in terms of the present and future with regard to the remaining mineral heritage.1 The discovery of a deposit of pyrophyllite in the South Mountain region of the Cumberland Valley indeed emphasizes the increased importance of a more exact inventory of the metal and mineral resources of Pennsylvania. Active geological work and research have been in progress for many years, but the surface has been little more than scratched. The results obtained thus far in survey and research have been extremely beneficial to the Commonwealth and a fundamental hub of its industrial development. But these activities are wholly inadequate in the face of rising demands for the future. The need for an accelerated program to continue a study of Pennsylvania's mineral resources on a more intensive scale was never more acute.2 In part, this has been caused by the insatiable demands of industry. It has been caused also by wasteful use and ignorance.

Jan 1, 1950

By John M. Dealy, Robert D. Pehlke

This note presents a summary of the available literature on activity coefficients at infinite dilution in binary metallic solutions, Table I. These data should prove useful in not only examining the therm-odynamic properties of binary metallic solutions, but also in predicting the activity of a component in a complex alloy. The relationship proposed by wagner1 for expressing the activity coefficient in dilute solution is of the form:

Jan 1, 1963

By B. K. Parekh, W. M. Goldberger

A novel process is proposed for continuous removal of ash and unreacted solids which become suspended in the oils obtained during coal liquefaction. The proposed method uses water in direct contact with the oil under conditions which cause the suspended residue solids to transfer from the oil to the water phase. Separation of the phases yields a product oil essentially free of suspended solids. The water is cooled, clarified or filtered by conventional low-cost systems, and recirculated. The paper describes experimental work leading to development of the novel concept and includes the result of batch experiments that establish the feasibility of the process.

Jan 1, 1980

By L. J. Erck

H EAVY-MEDIA separation continues to be the favored process for concentrating the coarser fractions by elimination of undesirable tailing and middling fractions. The first vessel used for heavy-media separation was the closed-top cone. Further developments then led to the Akins spiral separator which fulfilled the requirements for improving metallurgica1 separation as well as gaining mechanical advantages. During the last season there has been a substantial influx of separator designs for further improvements of metallurgical separation based on the heavy- media method as well as attempting to garner further mechanical advantages with reduction in power consumption to boot. The newest of these designs was the Hardinge counter-current separator which was introduced into the field last spring in two plants. Both Hardinge separators proved satisfactory in operation and substantiat-

Jan 1, 1950

By J. J. Brown

The ore-hearth was the earliest type of furnace used in smelting Mississippi Valley lead-ores, which are very pure, and low in silver-content. The first smelters made no attempts to recover lead from the smoke; and since about 15 per cent. of the lead in the charge escaped in this manner, early practice with the hearth was decidedly wasteful. At most of the large smelting-plants blast-furnaces with auxiliary roasters were substituted for the hearths long ago. But, upon the introduction of the Lewis and Bartlett bag-process for collecting fume, the ore-hearth was used by companies engaged in the manufacture of pigments, simply on account of the large percentage of fume made by it. In fact, the extraction of lead mas kept down by the use of hot blast and other devices. During recent years, however, several smelting companies have realized that the preliminary roasting of galena for the blast-furnace is not economical, and have, therefore, replaced the roasting-furnace with a modification of the old Scotch hearth, in which a large percentage of the lead in a charge is

Jan 1, 1912

By Guang Ping Cui

In this paper the imminent relationship between rock burst and its phenomenon with normal rock pressure and its appearance, as well as the factors of one changing into another have been analyzed. Based on this, the necessary and sufficient appearing factors of rock bursts have been put forward, and the term ''burst pressure" has been defined. According to the statistics data of tremendous rock bursts which appear in collieries in Hunan Province, the features of high frequency, great strength and shallow depth of the beginning burst have been found. There are some special structures in the coal seams, which are closely related with the burst phenomenon. A hypothesis of "star structure" has been suggested for the appearing mechanism of bursts. Inside and around this star structure the distribution rule of burst pressure and rock strength has been researched depending upon the theory of the limited stress field. A new description of the appearing causes of bursts has been raised.

Jan 1, 1984

By John Cogan, P. M. Gomez

A typical problem in applied rock mechanics is an accurate prediction of support requirements for deep rock cuts. This paper presents experience with this problem as obtained from excavations for a powerhouse at the Pine Flat Dam near Fresno, California. The project, sponsored by the Kings River Conservation District is still under construction. Highly jointed and weathered rock was discovered during initial excavation. Wedge failures along clay filled joints and bedding planes presented potential support problems. Detailed mapping of joints and beds was undertaken to establish basic patterns of all rock discontinuities including mean orientations and an estimate of orientation variations. Rock bolting patterns were devised to meet these patterns as excavation proceeded. Shear friction angles across joints and beds were estimated from rock wedge fallouts. Friction angles as low as 27º were identified on highly weathered joints. Weathering strongly influenced stability conditions. Examples of bolting patterns to stabilize critical slopes are presented.

Jan 1, 1982

By Kiyoshi Mizui

Processes for manufacturing prereduced iron pellets from iron ore dust occurring in iron works have recently begun on an industrial scale. Because of their high porosity and low mechanical strength, these prereduced iron pellets tend to oxidize again and disintegrate into fine particles during transportation and storage; this may result in such difficulties as decreased yield, undesirable work environment and heat generation during oxidation. A possible process for avoiding oxidation and disintegration of prereduced pellets is increasing the density through briquetting. The authors carried out briquetting tests under various conditions, attempting to find optimum briquetting conditions. They found that crushing prereduced pellets and adjusting the particle size to a certain range before briquetting increased the briquette strength and reduced the amount of binder needed. Oxidation resistance of briquettes and raw material pellets was compared in open air and at high temperatures. Briquettes showed superior oxidation resistance.

Jan 1, 1977

By E. Higgins

It is the purpose of this paper to set forth the relation and function of the various organizations and institutes engaged in the promotion of safety in the iron mines of the Lake Superior region…

Jan 1, 1915

By G. W. P. Rengstorff, L. E. Olds

PREVIOUS research has shown that cast molyb-denum has good ductility at room temperature if the metal is sufficiently pure. In practice, however, it is very difficult to reduce the impurity content of molybdenum to a few parts per million—the maximum content of impurities allowable to obtain reasonable ductility in coarse-grained molybdenum. Also, subsequent fabrication may reintroduce enough impurity to damage ductility greatly, unless extreme precautions are taken to protect the metal during working. The major impurities which embrittle molybdenum are oxygen, nitrogen and, to a lesser degree, carbon. It is reasonable to assume that the harmful effects of such impurities might be neutralized by small amounts of alloying additions. The desired alloying elements would be those which might fonn stable metal oxides or nitrides that would not be harmful to ductility, or thosewhich might increase the tolerance of molybdenum for oxygen and nitro-

Jan 1, 1958

By R. C. Kadyk, C. J. Bise

High-voltage cable couplers are convenient and widely used accessories in modern coal-mine power distribution systems to help extend and retract power-feeder cables throughout a mine. Coupler design has tried to keep pace with the industry's desire to move to higher distribution levels, but the increase in recorded failures of 15-kV class couplers, which serve the 12.47-kV and above distribution levels, has inhibited this transition. Problems associated with the effects of partial discharge on high-voltage cable couplers are analyzed. The phenomenon of partial discharge is discussed, a testing standard is developed, and various coupler designs are subjected to its requirements. An analysis of test results and results based on field applications are provided.

Jan 1, 1985

By V. H. Wilhelm

Greater stabilization in the petroleum industry was effected during 1934 through stricter compliance with curtailment measures and the establishment of the Pacific Coast Petroleum Agency. Various estimates of individual, company and state reserves revealed the fact that they were inadequate to sustain the present rate of production over a lengthy period, therefore drilling operations were increased during the year both in proved and wildcat territory. This greater activity resulted in the addition to reserves at Mountain View, Mount Poso and Edison in Kern County, Santa Barbara in Santa Barbara County and Playa del Rey in Los Angeles County. Additional reserves were also established in the Long Beach and Santa Fe Springs fields, in Los Angeles County, due to operators being successful in isolating small prolific sand bodies, formerly disregarded during the flush production periods.

Jan 1, 1935

By L. S. Castleman, L. L. Seigle

IN a recently reported investigation, J. B. Clark and F. N. Rhines1 used a diffusion couple technique to determine the number of intermetallic phases which should be present in the Al-Mg equilibrium phase diagram. Their method was an application of the following generally accepted principle. If a diffusion couple made up of two metals is annealed at a given temperature for a long time, all the phases of the binary system which exist under equilibrium conditions at the diffusion temperature will form intermetallic layers. It is important that the diffusion temperature be high enough and the diffusion time be long enough to permit the nuclea-tion of all thermodynamically stable phases at the interface of the couples and their growth to observable thicknesses. These simple time-temperature criteria are at times difficult to satisfy, and it is the purpose of this note to point out a situation in which this is the case. The authors are currently studying diffusion bonding in the Al-Ni system." It is well established

Jan 1, 1958

By Franc R. Joubin, D. H. James

Uranium exploration in the North Shore area of Lake Huron goes back to 1847 when J. L. LeConte, a distinguished American geologist, identified a pitchblende-like mineral which he called coracite from specimens sent from a locality north of Sault Ste. Marie. In 1948 a search for the LeConte occurrence resulted in discovery of the Camray field, some 70 miles north of Sault Ste. Marie. Prospecting the Camray field yielded about 30 pitchblende occurrences spread over approximately 200 sq miles. Almost without exception these discoveries consisted of narrow, short, pitchblende-filled fractures, within or along the contacts of diabase dykes cutting pre-Cambrian Archean granite and gneiss. Eight discoveries were diamond drilled and three were explored underground, but none proved to be of economic value. Uranium prospecting at this time spread far afield, and it was in 1949 that radioactive conglomerate was discovered in Long Township of the Algoma district midway between and 90 miles from Sault Ste. Marie and Sudbury. F. Joubin examined this discovery at that time but could not interest capital in its development.

Jun 1, 1956

By Bruce A. Lamberton

In U. S. underground mines concrete work is not widely used. Timber and steel are cheaper, and there are few serious water problems. But in the Union of south Africa men dig deeper, more persistently, and probably more profitably than anywhere else on earth. Some gold mines near Johannesburg are below the 10,000 level and employ as many as 35,000 natives on a single property. Underground substations, pump chambers, and air conditioning plants have capacity to serve small cities. The complexity and extent of underground operations and the heavy subsurface water flows, especially in the new Free State gold fields, require heavy in a Deep concrete installations.

Oct 1, 1956