Search Documents

By P. W. Bakarian, John C. McDonald

Three magnesium alloys were processed in various ways to exhibit a wide variation in the ratios of yield strength and tensile strength in the rolling direction compared to the cross-rolling direction. Basal-plane pole figures were prepared from several specimens. A fair correlation was observed between the property ratios and the ratio of percent of poles oriented in the cross-direction quadrants compared to the percent oriented in the rolling-direction quadrants of the pole figures. THE modes by which magnesium crystals deform are such as to lead to marked preferred orientations in all forms of wrought products. The effect of the active modes at room temperature, coupled with these orientations, is often to produce a lower compressive yield stress compared to the tensile yield stress. The phenomenon is due to easy twinning in compression, and has been well-related to the preferred orientations as described by basal-plane pole figures of the hcp magnesium single crystal. The literature contains some information on the variation with test direction of the tensile properties of sheet, but no quantitative relationship to the observed pole figures has been established. These effects have been reviewed in the few com- prehensive treatises in English which have been written on magnesium technology and metallurgy.1°3 Roberts presents several pole figures, but no tensile-property data in the plane of the sheet. Raynor has no pole figures, but quotes Frommer's4 results. The information in Beck's compendium more or less parallels the results of Jones and powell.5 In both a Mg + 1.5 Mn alloy and a Mg + 4.6 A1 alloy, cold rolling was found not to change the general situation of higher properties in the cross-rolling direction,* than in the rolling direction. Thomas'6 X-ray studies of Jones and Powell's specimens did not permit correlation of properties and preferred orientation. Ansel and Betterton7 report tensile and compressive properties on three other alloys as a function of degree of cold rolling, plus a recrystallizing anneal. As rolled, there was a change in anisotropy with degree of reduction, but all alloys were reasonably isotropic in tension when annealed. X-ray diffraction photograms illustrated the kinds of orientations present, but were not correlated with the properties. Bakarian8 has described a method of determining quantitatively a preferred orientation, and illustrated the method by applying it to pure magnesium and two of its alloys. This method was used in the present work as a basis for correlating the strength properties with the texture.

Jan 1, 1965

By VERITAS

THE most concentrated industry of major character in the United States is that of the Ford Motor CO., which is to say Henry Ford. Its sole function is to supply the public with a cheap motor car which it does to the extent of two million or so per annum. In doing this, a relatively small profit per unit is multi- plied to an enormous aggregate per annum and has resulted in the creation of one of the greatest industrial fortunes of the world. The industrial and sociological consequences of .this are bound to be immense. On the physical side the production of two million automobiles means the consumption of two or three million tons of materials, chiefly metals, in the 'direct form of the finished product', and a huge additional tonnage of coal and other things that ,are consumed en route, and also the labor of many thousands of men. In the development of a business on this scale it was but natural that the Ford Motor ,Co. should seek to supply itself with the raw 'materials it needs, and they being so largely coal and metals the company is brought into close contact with the mining and metallurgical industries. It is a huge consumer of - steel. It is the fourth largest consumer of copper. It is a large consumer of lead, tin, aluminum and zinc. The mining and metallurgical industries have, therefore, good reason to learn to know Henry Ford, his personality, his thoughts and his policies.

Jan 1, 1924

By Dudley L. Davis, E. C. Peterson

INTRODUCTION THE Darwin District is 30 miles east of Olancha which is 220 miles north from Los Angeles via U. S. Highway No. 6. The ore deposits occur in the Darwin hills that have been elevated above the Darwin Plateau by typical basin and range-type faults. Some of these faults have been active quite recently as shown by the displacement of Quaternary (?) basalt flows and the rejuvenation of erosion in Darwin wash. The ore bodies occur as fissure fillings and replacement of favorable beddings in a thick series of Paleozoic limestones, dolomites, shales and quartzites. Rich oxidized lead-silver ores were discovered in the early seventies. By 1875, Darwin had a population of about 5000, and by 1880 several small mills and smelters had been built. Early exhaustion of surface ores, the isolated location of the district, and fluctuation of metal prices caused intermittent operations until World War II. The district production is estimated at about $3,000,000 prior to 1900 and perhaps $4,000,000 between 1900 and 1945 when Anaconda purchased the major producing mines. For the past two years, daily production has averaged 75 tons of direct shipping and 150 tons of milling-grade ore. At present, 300 tons of mixed oxide and sulphide ore are treated by flotation, the oxidized lead minerals being activated by addition of sodium sulphide after galena and sphalerite have been recovered from the circuit. Extraction averages 85 pct of the lead, 80 pct of the silver, and about 33 pct of the zinc in a bulk concentrate. The mill is designed so that minor changes permit selective flotation of pyritic lead-zinc ores encountered at depth. GENERAL GEOLOGY The oldest rocks in the Darwin hills are a series of Paleozoic limestones, dolomites, shales and quartzites probably Pennsylvanian in age. These rocks have been intruded on the west by the Coso granite batholith and on the east by a granodiorite stock. Numerous sills and dikes grading from orthoclase granite to gabbro are exposed in the underground workings. The sedimentary rocks have been considerably folded and faulted, the most prominent structure being a northwest pitching anticlinal fold, the crest of which lies just west of the ridge line of the Darwin hills. The east limb of this fold has been intruded by the granodiorite stock and east of the stock the sediments show several closely spaced anticlines and synclines. The minor flexures on the west flank of the major fold are structurally important in localizing the ore in the Defiance and Essex mines of the Darwin group. There are three principal systems of faulting and fissuring, most of which are post-intrusive and premineral in age, with minor amounts of postmineral movement. The Darwin tear fault is the largest, most persistent fault in the district. It strikes N 60 to 95°W, dips steeply south and is traceable for about 1o miles. It is a normal

Jan 1, 1947

By Frederick M. Becket

AFTER all the chronology that has been given, what is the present status of chromium steels? For the purpose of this discussion the different types of chromium steels can be divided into three classifications-those containing relatively low , percentages of chromium, say 5 per cent or less; the medium-chromium steels containing up to about 18 or 19 per cent chromium; and the steels containing still higher percentages of chromium, and some of the special alloys. Chromium has some unique effects in steel, so it is well to make a few generalizations. The affinity of chromium for carbon is great and the metal is unique in the manger in which it supplements and enhances the effects of carbon. Chromium retards -considerably the thermal transformations on cooling and exerts an opposing influence both on the absorption and precipitation of the carbides in steel. These statements make it easy to understand the fact that chromium .steels are capable of producing a hardened product at a much slower rate of cooling than is, true of plain carbon steel, and that chromium carbide or -the mixed carbides of iron and chromium do not contribute to brittleness to as great a degree as does iron carbide.

Jan 1, 1929

By Richard Moldenke

The paper describes the making of pig iron from the Mayari iron ores of Cuba. The outstanding feature f this pig iron is a considerable content f nickel and chromium. As a marked improvement in the quality of castings has been noted when this iron is used in the foundry mixtures, a series f melting tests f mixtures of great variety of composition was conducted with the idea f getting comparative strengths from which the effect of nickel¬chromium could be seen. These tests, on account of their number, and degree of accuracy desired, were made by the crucible melting method. The paper gives the tables of results, a series f curves showing the inter-relation of the elements involved, and a summary of the conclusions derived. THE presence of nickel-chromium in pig iron made from Cuban ores is so well known that the word "Mayan" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there has been increasing interest in these ores. The TRANSACTIONS contain numerous references to them. This iron ore, which is shipped to the. United States in the nodulized state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of Mayari ore for pig iron for the better grades of finished iron products. The present point of consumption of Mayari ore is at Sparrow's Point, where Mayari pig iron of any desired composition is made. The com-

Jan 9, 1922

By T. Sterry Hunt

THERE are about sixty bodies which chemists call elements ; the simplest forms of matter which they have been able to extract from the rocky crust of our earth, its waters, and its atmosphere. These substances are distributed in very unequal quantities, and in very different manners. As regards the frequency of these elements in nature, neglecting for the present those which constitute air and water, and confining ourselves to the solid matters of the earth's crust, there are a few which are exceedingly abundant, making up nine-tenths, if not ninety-five hundredths, of the rocks so far as known to us. The elements of which silica, alumina, lime, magnesia, potash, and soda are oxides, are very common, and occur almost everywhere. There are others which are much rarer, being found in comparatively small quantities. Many of these rarer elements are, however, of great importance in the economy of nature. Such are the common metals and other substances used in the arts, which occur in nature in quantities relatively very minute, but which have been collected by various agencies, and thus made available for the wants of man. It is chiefly of the well-known metals, iron, copper, silver, and gold, that I propose to speak to-night; but there are two other elements not classed among the metals, which I shall notice for the reason that their history is extremely important, and will, moreover, enable us to comprehend more clearly some points in that of the metals themselves. I speak of phosphorus and iodine. You all know the essential part which the former of these, com- * An address before the Polytechnic Association of the American Institute, during the meeting of the American Institute of Mining Engineers in New York. Printed in this volume by request of many members.

Jan 1, 1873

By T. Sterry Hunt

WET processes for the extraction of copper from its ores have of late attracted much attention, especially in Europe, where the use of oupriferous iron-pyrites as a' source of sulphur prevails. These processes present an additional interest, when, as is often the case, the copper-ore's to be treated contain one or both of the precious metals, since the complete separation of these from copper, either in the dry or the moist way, is, as is well known, one of the difficult problems of metallurgy. The principal wet processes hitherto in use for the extraction of copper from its ores, may be included under three classes : I. Those in which the copper in snlphuretted ores is rendered soluble in water by calcining them, after a preliminary roasting which removes the greater part of their sulphur, with a portion of common salt, by which the copper is converted into a chloride (Long-maid and Henderson), or with sulphate of soda, by which sulphate of copper is formed (Monnier). Allied to these is the method by which a portion of the copper is got as soluble sulphate by roasting without addition, a process which is sometimes modified and rendered more complete by re-roasting the lixiviated residues with the addition of a portion of raw sulphuretted ore (Bankart). II. Those methods in which free chlorhydric or sulphuric acid is used to dissolve the copper- from oxidized or roasted ores. These, while simple and efficient, are too costly, except in certain localities where chlorhydric acid is a waste product. Related to them is the plan which consists in exposing the oxidized and moistened ores to the slow action of sulphurous acid mixed with air, by which a soluble sulphate of copper is formed. It has been proposed to decompose the solutions of sulphate or chloride of copper by sulphuretted hydrogen, thus separating the copper as sulphide, and using the liberated acid to dissolve fresh portions of oxidized copper. It is, however, the almost universal practice to throw down the copper from its solutions, however obtained, in the metallic state by the use of iron, either scrap-iron or iron-sponge; although in some instances

Jan 1, 1882

By T. Sterry Hunt

Jan 1, 1882

By ERJIINICI FERRARIS

1. HISTORICAL REVIEW AND INTRODUCTION. THE development of the mining industry in Sardinia dates from the application of the minim law of 1859, which, following the example of the French mining law of 1810, declared prospecting to be free, and suppressed the liens which had previously attached the mine to surface ownership. The first ore-dressing plants were installed by German engineers upon the classic models of the Harz and of Freiberg; but in 1880 Sardinia commenced to open a new path in that industry, utilizing the refuse from the mining of rich, selected minerals, of poor deposits, and of mixed ores. The first experiments were attempts to adapt the existing apparatus to local conditions, but progress was rapid, as was demonstrated already in 1887 by the calamine-dressing-mill of Monteponi, which exhibited a large plant designed in accordance with the experience gained, and constructed entirely in the machine-shops of the country, after new models and designs.1 This example was followed two years later by the Société Malfidano, with a large plant of the same sort, and with the reconstruction of the old-fashioned-dressing-mill, built in 1880 by the Austro-Belgian Company. In 1900, almost all the mines of Sardinia had adopted the new designs, and the island contained 32 concentrating-works, employing 2,000 h.p. and 1,924 workmen. Since that time, there have been added a large dressing-mill for blende at Gennamari, and two for calamine, at San Giovanni and at Masua, while the establishments at other mines have been enlarged and perfected. For the treatment of intimately mixed ores, a large establishment has been built upon the new

Jan 5, 1908

By Reginald E. Hore

I. INTRODUCTION. SINCE the discovery of silver at Cobalt, Ontario, in 1903 more than 100,000,000 oz. of silver have been produced b: the mines in the Nipissing district, and there is reason to believe that at least as much more will be produced in the next five years. The estimated value of the aggregate output o ore to the end of 1910 is $48,327,280. The ore yielded 93,977,833, oz. of silver and was mined at a net profit of about $26,000,000. For 1910 the production was 30,558,825 oz. valued at $15,436,894, and yielding a profit of about $9,000',000 The details of the production of the Cobalt district for the years 1904 to 1909, inclusive, are given in Table I. TABLE I.-Silver-Production of the Cobalt District, 1904 to 1909 SMELTING-ORE. Production. Value. Silver-Content. Value Per Ton Ounces. Oz. Per Ton. 1904 206,875 $111,887 1,309 $708 1905.:.... 2,451,356 1,360,503 1,143 634 1906 5,401,766 3,667,551 1,013 687 1907 10,023,311 6,155,391 677 416 1908 18,022,480 8,468,293 736 363 1909 22,436,355 10,809,872 809 389 CONCENTRATES. 1908 1,415,395 $665,085 1,240 585 1909 3,461,470 1,651,704 1,174 559 The shipments from Cobalt are in the form of smelting-ore, concentrates from milling-ore, and bullion. The smelting-or( is largely high grade, averaging about 3,000 oz. per ton- A

May 1, 1911

By S. A. TAYLOR

THERE is probably no other mineral industry of which the public has as much information and misinformation as it has of the coal industry. Unfortunately, however, the general public's knowledge of the coal industry, outside of the particular kind of coal it is accustomed to, by reason of use, is largely made up of information received from newspaper and popular magazine articles, in which the mine workers are depicted as overworked and mistreated men, and the coal operators as "coal barons." Those who have any specific knowledge of exact conditions in the coal industry know how unjust and un- fair such an opinion of the coal industry is, not only to the miner but to the operator as well. Many reporters and writers of magazine articles are misled by statements regarding the condition of the miners that are exaggerated and not founded on facts and, if an investigation of the conditions of the miner's work, his habitation and surroundings were fairly made, it would at least compel more truthful statements by those who write for public reading. That such an investigation would not reveal anything that was wrong, or anything to be censured or cured, no one, I think, would maintain, but I do think that any fair investigation of the facts would show that conditions in and around the newer and later-developed coal mines and communities would compare favorably with those of manufacturing districts, and that where the mines and com- munities are old and not very attractive places to work, or live in, they carry with them other considerations, compensating for these conditions, and cannot be remedied by reason of a lack of sufficient coal to warrant economically any costly changes.

Jan 1, 1926

By R. Kossowsky

Structural changes in Be-Cu, Be-Ni. Be - Ag, and Be-Fc alloys pressurized in a solid medium were invesligated by resistivity measurements , X-ray diffrac lion in situ and metallogvaphic examination. Some limited tests in liquid medium were also conducted. Good correlation was oblained between diauges of slope of relative resistance us pressure and changes in diffraction pattern. Metallographic examination rez:ealed that the copper, silver, and nickel alloys lwiu heauily due to the applicalion of pressure at room temperature. Using polarized light technique {1012}, {1011}, and possible {1010} twinning planes were identified. At eleuated temperature twinning was moslly confined to the {1012} planes. Although twin-ning could be promoted by application of hydroslutic pvessure (liquid medium), it was strongly enhanced by the pvesence of a nonhydvostatic shear component due to pressurizalion in a solid medium. It was further obserced that a decrease in grain size inlnibiled twinnitzg activily. A great deal of effort has been expended in recent years to render beryllium useful for structural applications. Efforts were concentrated towards a possible phase change and to promoting other than basal deformation modes. Quenching experiments to obtain the high-temperature bcc phase have failed,' nor were alloying additions successful in improving ductility of the brittle hcp phase.2 Herman et a1.3 have reported a new {1011} twinning mode in a Be-4.4 wt pct Cu alloy oriented for a C axis compression sustaining loads to 440,000 psi. A new approach using high-pressure techniques was undertaken at Curtiss-Wright, Wright Aeronautical Division Laboratories. Marder4 reported a 25 pct decrease in relative resistance of commercially pure beryllium at 92 kbar. He proposed that this discontinuity corresponded to the bcc phase found at high temperature; however, X-ray diffraction in silu did not confirm a phase transition.5 contre6 has recently shown that the bcc transition in pure beryllium is lowered to 800°C at 80 kbar accompanied by a 50 pct increase in relative resistance. The purpose of this paper is to report on one phase of an investigation of the effects of high pressures and temperatures in beryllium alloys, namely, twinning behavior in Be-Ni, Be-Cu, Be-Fe, and Be-Ag alloys pressurized to nearly 100 kbar and temperatures up to 200°C. EXPERIMENTAL METHODS Material was obtained from Nuclear Metals, Inc., in the form of a 1.5-mm-diam wire extruded in stainless-steel cladding at 1600° F. Nominal composition of the alloys is listed in Table I, and the major impurities are are given in Table 11. Pressures to 100 kbar* were ob- tained using a National Bureau of Standards type 100/400 ton tetrahedral unit supplied by Barogenics, Inc. This type of apparatus contains a retaining sleeve with a conically tapered internal surface and four pressure-intensifying anvil assemblies with tungsten carbide tips. The 10-mm-long specimen fits into a pyro-

Jan 1, 1968

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a general and loosely used term to denote almost any kind of calcareous material or finely divided form of limestone or dolomite, as well as burned forms of lime. However, according to Webster, lime is only calcined limestone (known as quicklime, unslaked lime, or calcium oxide). It also embraces the secondary product of quicklime, i.e., hydrated lime or slaked lime (calcium hydroxide). There are two basic types of limestone used for lime manufacture-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts. The only difference is that the dolomitic types are a combination of the elements calcium and magnesium, in varying percents, whereas high calicum limes contain less than 5% MgO down to 1/2%. In either case a pure form of limestone of at least 97% combined carbonate content is needed to make salable lime, barring a few exceptions. The calcination of both types is diagrammed chemically as follows: [ ] In the foregoing reversible reactions the limestone is burned (calcined) in lime kilns, with the carbon dioxide content of the stone expelled as a gas. The weight loss during calcination of pure high calcium limestone is 44%; with equimolecular dolomitic limestone, the weight loss is 48%. Since lime has a strong affinity for CO_, particularly if moisture is present, it will readily revert to its original carbonate form. This occurs when quicklime "air-slakes" and adsorbs CO.. from the air. Thus, quicklime is perishable and should be stored in dry, water-tight areas. Depending upon the type of kiln used and the physical structure of the stone, the size of the quicklime may range from sandlike granules to 8 in. lumps. However, pebble sizes ranging from 1/4 in. to 2 in. are the most common. Screened quicklime fines are also com¬pressed (pelletized) into 1 in. pellets. For some purposes ground or pulverized forms of quicklime are used, ranging from No. 10 mesh to dust. Generally a pebble of quicklime is about the same size as the pebble of limestone before calcination (perhaps shrinking slightly). A more stable form of lime is hydrated lime. This is obtained by adding water to quicklime, slaking it into a dry, fine, subsieve size white powder. Because its affinity for moisture has been satisfied, it is not vulnerable to further moisture like quicklime. However, it has the same strong affinity for CO_. The following reversible chemical reactions illustrate how hydrated lime when heated (or dehydrated) can revert to the original oxide form:

Jan 1, 1975

CONTENTS KANSAS-H. S. BRYANT 3 TEXAS, EXCEPT GULF COAST-M. C. CHENEY 14 GULF COAST-L. P. TEAS 21 TEXAS PANHANDLE-W. E. HUBBARD 29 LOUISIANA, ARKANSAS AND MISSISSIPPI L H. K. SHEARER 37 ROCKY MOUNTAINS-R. C. COFFIN 43 CALIFORNIA-V. H. WILHELM 51 MICHIGAN AND THE TRENTON FIELDS OF OHIO AND INDIANA-M. G. GULLEY 65 ILLINOIS, WESTERN KENTUCKY AND WESTERN INDIANA-A. H. BELL . . . 73

Jan 1, 1932

By H. NORTON JOHNSON

THE oil industry in California during 1929 reached new heights and new depths in the discovery and development of the oil resources of the State. The discovery of new fields, and more especially the discovery and development of deeper prolific sands in known fields has, for the first time in its history, brought the potential production of completed wells within the State to over 1,000,000 bbl. oil per day. Constant improvement in equipment and technique has made possible economic development to depths unheard of but a few short years ago. Commercial production from a depth of over 4000 ft. was considered quite an accomplishment in 1923 when the Meyer sand at Santa Fe Springs was developed, and when later oil was successfully raised from this depth.

Jan 1, 1930

By P. F. MINISTER

AT Lime Spur, Mont., the East Butte Copper Mining Co. has been quarrying limestone for twenty years. The quarry is beside the Northern Pacific R. R. in the Jefferson River canyon, 4 ½ miles east of Cardwell, at Lime Spur, Montana. HISTORY This quarry was opened early in 1900 by Dan Morrison of Whitehall, the discoverer of the Morrison cave, to supply a demand for smelter flux. Limestone was sold to the Pittsmont smelter of The East Butte Copper Mining Co. and to the Butte Reduction Works. As no particular effort was made at the quarry to select the rock that delivered to the smelters was unduly high in magnesia and impurities. The East Butte com¬pany, therefore. Bought the quarry. in 1909 and confined operations to the high-grade beds in order to supply rock of the desired purity for its own smelter and the Butte Reduction Works until the latter shut down. It also developed a market for some of its rock with the sugar factories. The latter market increased until in later years all rock, larger than 4 in. in size over a bar grizzly, was being shipped to the sugar factories, and the rock smaller than 4 in. was being used as a flux in the blast furnaces at the Pittsmont smelter. In 1924, the East Butte concluded a contract with the Anaconda company for the treatment of its ores, and the Pittsmont -smelter -was shut down: which made the minus 4-in. rock a useless by-product. Since there was not enough revenue in the sugar rock alone and also because of limited waste room it became necessary, if Lime Spur was to continue to operate, to increase- the proportion of plus 4-in. rock and to develop a market for the minus 4-in.

Jan 1, 1930

By Richard L. Ashbrook, John F. Wallace

Several high-temperature eutectics of cobalt and nickel alloys were modified by small additions of selected elements. Thes-e alloys were compared to unmodified melts for microstructural variations. A few modified compositions were selected on the basis of structure and their tensile and stress-rupture behavior determined. The results of stress-rupture tests in air at 1800 F and room-temperature tensile tests of four high-temperature eutectics showed modification capable of producing substantial improvements in properties. The microstructures were altered and mechanical properties improved by: a.) dispersing a subordinate phase more uniformly throughout the matrix; b) replacing large continuous -network or platelike constituents with small equiaxed discontinuous phases; and c) by forming new, finely divided phases. tHE term "modification" is most commonly used to describe the refinement in microstructure of the Al-Si eutectic that occurs as a result of rapid cooling from the melt or on slow cooling after treatment with small amounts of sodium.1 "Modification" has also been used to describe the change from flake to spheroidal graphite in the austenite-graphite eutectic of cast iron.2 This change of graphite shape is accomplished by small additions of cerium or magnesium.3 Other systems have also been shown to be capable of modification, for example: Pb-Sn by copper;4 Al-Cu by sodium;5 Al-Mn by sodium;5 and Pb-Sb by aluminum.5 Although modification of Al-Si alloys and cast irons is usually accompanied by improved mechanical properties, a general definition of modification has been suggested to include the effect of small quantities of impurity elements on the microstructures of all eutectic alloys, regardless of the effect on the mechanical properties.6 In this paper, the term "modification" is employed in a broad sense to include the formation of third phases or even the supplanting of one of the binary eutectic phases by a third phase. The mechanism of modification, as for any solidification phenomenon, must be considered primarily in terms of nucleation and growth. Although both nuclea-tion and growth mechanisms are required to explain all the phenomena observed in connection with the solidification of modified eutectics, various investigators have usually favored one or the other.7"16 It has been shown that modification of a binary eutectic can be effected by addition of a solute element that has greatly different distribution coefficients or k values in the two phases of the eutectic. Under these conditions, differences in the temperatures at the solid-liquid interfaces of the two phases retard the growth of one phase with respect to the other.4 It has also been shown that increased undercooling favors a transition from a rodlike eutectic to a globular eutectic.17 A mechanism proposed for the transition from lamellar to rodlike eutectics depends on the concept of constitutional super cooling.18 The modification of eutectic alloys may be of interest for high-temperature service as well as at room temperature. Although "high-temperature eutectic alloys" may appear to be a contradiction in terms, many eutectic systems, including those studied in this work, have melting points in excess of 2400°F. One of the mechanisms by which high-temperature alloys are strengthened is dispersion of a relatively brittle phase such as an oxide, carbide, or an inter-metallic compound throughout a ductile matrix. For a given volume fraction of dispersed phase, strength is increased by decreasing the size and spacing of the dispersed particles.19'20 Furthermore, room-temperature ductility may also be increased by changing the shape of a brittle dispersed phase from platelike to equiaxed or spheroidal.8 Overaging and redissolving of the secondary phase limit the maximum temperature to which precipitation-hardened alloys can be used. However, in a binary eutectic system, both phases coexist up to the melting point. Although all eutectic structures are not completely stable,21 a dispersion-hardened cast high-temperature alloy might result if a fine distribution of one of the eutectic phases could be obtained during solidification. An additional reason for interest in eutectic alloys is their excellent castability.22 Since eutectic alloys, like pure metals, freeze at a single temperature rather than over a range of temperatures, their castability is superior to solid-solution alloys with long liquidus to solidus ranges. The purpose of this research was to study the effects of small solute additions on the microstructure and mechanical properties of a number of high-melting-point eutectic compositions.

Jan 1, 1967

By Mäkinen, Eero

OUTOKUMPU, a large copper mine in eastern Finland, has the distinction of being one of the few important mines in the world discovered by a geologist the late Otto Triistedt, of the Geological Sur- vey of Finland, having found the out- clop in 1910 by tracing glacial ore boulders, some of which had been carried as far as fifty kilometres. As the mine had no connection with either railways or waterways and the possibilities of transport were poor, the owners first tried the Hybinette hydrometallurgical process to extract the copper. The raw ore was finely crushed, treated by a sulphatizing roast. and then leached. The resulting solution was electrolyzed, using lead anodes. This experimental plant, having a capacity of 10,000 tons (all Ions are metric tons in this paper) of raw ore and producing 300 to LEO0 tons of electrolytic copper annually, was built in 1913 and run until dis-

Jan 1, 1938

By L. W. McKeehan

IT is no longer necessary, if it ever was, for your annual lecturer to apologize for including in his remarks frequent references to the arrange-ment of metal atoms in crystals and for basing his arguments that metals behave as they do upon their crystal structure. Neither will any objec-tion be raised because the large metallic crystals of which we will speak are hard to prepare and of negligible commercial interest. The particular set of physical properties we propose to discuss-ferromagnetic proper-ties-may require more justification. Very few in this audience are primarily, or even remotely, interested in the ferromagnetic behavior of the metals they handle. By no means all of you ever deal, by choice or by necessity, with metals which display any ferromagnetism at all, and even those who study or control ferrous metallurgy must usually depend upon electrical engineers for assistance in ferromagnetic applications. My excuse for talking about such an obvious specialty is, like all Gaul, divided into three parts. In the first place, the members of the com-mittee who select the annual lecturer must wish the speaker to confine himself to matters he has at least thought about before he prepares his speech. In the second place, the study of ferromagnetism in crystals has, as you will soon realize, suffered in the not-too-distant past from inade-quate metallurgy. Further progress probably depends upon proper use being made of the skill and knowledge of some members of the Institute of Metals Division who have not, before today, been asked to think about the problems presented here. Finally, there is at least a sporting chance that the ferromagnetic properties of a few metal crystals will give some insight into the more generally interesting properties which they share with nonferromagnetic metal crystals.

Jan 1, 1934

By Allen Garrison

A PREVIOUS paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their com-position, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions, Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. EXPERIMENTAL PROCEDURE The difficulties involved in the measurements of the flow character-istics of plastic fluids are too familiar to recite, The possible applications of some of the well-known instruments to this problem have been ade-quately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measure-ment of clay or shale suspensions, Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first require-ment is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1939