Search Documents

By Clarence E. Sims, George A. Moore

INTRODUCTION IN previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficient time is allowed. For precise work, the method claims preference because the equipment for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the transformation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approximately 2 hr. While it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual error may be more or less constant between samples. For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temperature process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and evolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1948

By A. R. Amos, S. B. Patterson

Log washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate completely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5" to 10" and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1938

By Walter B. M. Davidson

Phosphorus is one of the elements having the widest distribu tion, and phosphoric acid plays an important part in the composition of the crust of the earth. It is allied in various chemical combina- tions with many bases, of which lime, alumina and iron are the most common. It is difficult to state in what chemical combination phosphoric acid predominates in the crust of the earth, for while phosphate of lime, as the mineral which is sought for and found in deposits of economic value is the most familiar, it is probable that the phosphates of alumina and iron are the most usual forms in which phosphoric acid exists in all soils not essentially calcareous. It has been shown by thousands of analyses that all fertile soils contain from a trace to 0.5 per cent. of phosphoric acid. All limestones, dolomites and chalks contain it in proportions which, though usually small, are large enough to make careful analysis necessary in the selection of limestone as flux for iron-smelting. It is generally Trenton limestones that are found best for this purpose, the more recent strata being more phosphatic. In some places phosphoric acid replaces carbonic acid, and the limestone or chalk becomes phos phatic to a large degree, or sometimes pure phosphate of lime. The waters of the ocean, from very early periods, have contained phosphoric acid. Different analyses show varying contents; it is asserted that some portions of the Gulf Stream are more phos phatic than the surrounding waters of the Atlantic. Many springs, usually from limestone regions, contain soluble phosphates in vary ing quantities. I think it safe to assert that phosphorus is nearly the most widely and evenly distributed element on the surface of the earth, and probably the most subdivided. This can be readily understood when the important part which phosphoric acid plays and has played in the vital cosmos is taken into consideration. Phosphorus was on the earth in gaseous, liquid or solid form before the dawn of life, and since then all animal and vegetable creation have combined with the

Jan 1, 1893

By P. W. Bridgman

It is characteristic of most scientific investigators that they are not satisfied with the discovery of new facts, no matter how curious or unexpected, but that along with the factual discovery there is a constant effort to understand. It appears that one's interest in, and satisfaction with, the discovery of an array of new experimental facts is enormously increased if one has at the same time a theory or hypothesis guiding one's expectation of what sort of new experimental discovery may lie around the corner. Conversely, as a theoretical physicist one's satisfaction with his theory is greatly enhanced if along with the development of the theory can go the discovery of new experimental facts, confirming or perhaps modifying the theory as it grows. Of course, there have been long arid stretches in the history of physics in which new data of unquestioned ultimate importance have piled up, without much inspiration or illumination in the way of understanding. For 50 years spectroscopy had such an arid history, but how irksome this was felt to be is plainly shown by the almost audible relief that greeted the first success by Bohr in injecting understanding into the situation, and by the fresh rush of experimenters into this field when the prospect of understanding had once been offered. The investigations in the field of high pressure, which have occupied me for a long time,' until the last few years have been in very much the same sort of situation as spectroscopy before the advent of Bohr. A great many kinds of data were collected for a great many solid and liquid substances, and there could be no question of the importance of these data, because the uniform change of dimensions produced by hydrostatic pressure is perhaps the simplest conceivable type of alteration to which a body can be subjected. But except for a few isolated flashes, there was no theoretical illumination, so that it had to be to a large extent the enthusiasm of the collector that kept me going. However, within the last few years the wave-mechanics theory of solids has progressed so rapidly that

Jan 1, 1938

In the 100' years since AIME was founded in 1871, the Institute has issued a great many publications in a variety of forms: periodicals, Transactions volumes, and special volumes or books. The following is a brief history of AIME publishing with some suggestions for proper referencing. TRANSACTIONS AIME Transactions volumes have been numbered consecutively since No. 1 was issued in 1873, including papers for the period 1871-1873. One or more volumes have been issued each year and may be divided into three general time periods: General Volumes (1873-1927), Volumes classified by subject matter (1928-1949), and the present practice, begun in 1949, of issuing three volumes per year, one each in the fields of mining engineering, metallurgy, and petroleum technology. The broad divisions of subject matter in each of these volumes correspond to the technical areas of the three constituent societies of AIME. AIME's Technical Publications, usually designated by TP number's (until the change in numbering system by the Society of Mining Engineers in 1958), may, with some exceptions, be referenced to an AIME Transactions volume. Reference to a specific volume, rather than paper number, is the preferred reference, since the volumes are the form of publication most commonly available in libraries. In many cases, over the years, the Technical Publications may also have been available in some other form, either as separates or in a periodical. General. Volumes (Vols. 1-78, 1873-1927): Until 1927 all papers eligible for Transactions were published in general volumes with no systematic attempt made to segregate the material on the basis of the technological fields to which the papers related.. One volume per year was issued from 1873 until 1912; from 1912 until 1927 from two to four volumes were issued annually. In addition to the Transactions papers, these volumes carried some of the proceedings of the business meetings of AIMS. Subject Volumes. (Vols. 79-183; 1928-1949): The material for these volumes was segregated according to subject matter, and up. to seven volumes were issued a year. In the latter part of the period, from 1934 on, there was one volume each' year for the Petroleum, Institute of Metals, and Iron and Steel Divisions and-the remaining papers were grouped in various ways and is sued whenever sufficient numbers of papers had accumulated: The subject volumes containing mining engineering papers are listed in Table 1. The volumes for the period, 1936-1949 are included in this Cumulative Index. Each of the Transactions volumes carries on the binding the year of publication; this date does not give an indication of when the papers included were originally presented at meetings. The contents of the volumes usually list the meetings at which. the papers were presented. Not all papers from a given meeting necessarily are in one Transactions volume. Some of the earlier volumes do not have a number on the binding or within the volume. In 1934 numbers" were assigned to all Transactions volumes, commencing with the 1871-1873 volume as No. 1. Many of the papers published [ ]

Jan 1, 1972

By C. A. Wert, M. G. Coleman

The Zener relaxation in alloys in the a! solid-solution region of the Cu-Ni-Zn ternary system has bear investigated. Of the binary solid solutions that bound this region, Cu-Zn and Ni-Zn exhibit measurable Zener peaks whereas Cu-Ni does not. At constant atomic percent copper, the Peak height drops uni.forinly from the value in the Cu-ZTL binary to zero in CIA-Ali. The cariation of peak ternperatuve with composition is linear. At constant atomic percent zinc, the peak height in the ternary alloys goes through a large maximum as compared with the binary values. The temperature of these peaks varies smoothly with composition. The half-width of the peaks in the ter nary alloys, however, are much larger than those in the binaries. A large enhancement of the relaxation strength of the Zener relaxation in ternary Au-Ag-Zn alloys as compared to the relaxation strengths in Au-Zn and Ag-Zn binary alloys was observed by Firson and ert.' Since this effect was unexpected, the present study was devised to investigate whether enhancement of the Zener relaxation in ternary alloys is a general feature or is particular to the Au-Ag-Zn system. We have chosen the Cu-Ni-Zn alloy system for this investigation. Measurable Zener relaxations are observed in both the Cu-Zn and the Ni-Zn binary systems, but not in the Cu-Ni binary system. A large solid-solution region extends to large concentrations of zinc, making it possible to vary composition of the alloys over a wide range without crossing phase boundaries. EXPERIMENTAL PROCEDURE Two series of alloys were prepared. the first at constant atomic percent copper, the second at constant atomic percent zinc. The compositions of these alloys are shown by the circles in Fig. 1. The alloys were prepared by melting the individual components, each of which had previously been vacuum-melted, in an evacuated quartz capsule in an induction furnace at 1500 C. The capsules containing the molten alloys were quenched in water to reduce coring. Any individual melt which exceeded 0.001 pct weight loss was discarded. The ingots were swaged to a 50 pct reduction of area and annealed for 1 week in an evacuated quartz capsule to aid homogenization. The alloys were then

Jan 1, 1967

By R. V. Higgins, A. J. Leighton

A fast method is needed for calculating thoroughly the performance of two-phase flobr~ in reservoir rock with complex geotrietry. The authors present such a method and .slzow its accuracy by romparison with laboratory performrrnce of a five-spot pattern. In making the performance c.alculations, the octant of the five-spot pattern was divided into four channels. The computer tinle required for the culculation was one rllinrcte. This is rorighly about minute per channel. INTRODUCTION By using an electronic computer it is now possible to make reservoir performance calculations in which fewer assumptions and more significant variables are included than was possible with a desk calculator. These performance calculations include such variables as the properties of the reservoir rock and its contained fluids, properties of the rock-fluid system and even different well-spacing patterns. Usually, the more variables that are included the higher the computer cost—and time on the computer is expensive. As a result, a short procedure is needed so the many variables will be included and accurate performance calculations will result. If a reservoir is composed of alternate layers of permeable and impervioi~s rock, and if each conducting layer has a different relative permeability, the combined computer cost for calculating each layer by the present long computer programs (which includes different well-spacing patterns and other variables) would be expensive. The performances of complex spacing patterns in a field often are studied by a potentiometric model, but in these model studies the analogy is to the flow of only a single phase. This paper presents a procedure to calculate the performance of a five-spot pattern with two phases flowing using a potentiometric model as a guide for the dimensions of channels and other related data. The time required to calculate the complete performance is about one minute on the IBM 7090 or four minutes on the IBM 704. The procedure can be extended to calculate the performance of more complex well spacings or an entire field with little modification. The procedure has been tested on the performance of the laboratory water floods of a five-spot pattern reported by Douglas, et alThe range of viscosity ratios in the laboratory experiments is from 0.083 to 754, which is extensive. The accuracy of the performance calculations is excellent as shown by the plotted points in Fig. I. The recovery as influenced by the geometry of the five-spot, taking into account the deviation from true radial character, has been predicted by Aronofsky and Ramey." The authors used a potentiometric model to determine the sweep efficiency to breakthrough of the flooding agent. Dyes, Caudle and Erickson,' by means of a laboratory model, show the influence of mobility ratio on recovery after breakthrough of the injected material. Dyes, et ai, used the X-ray shadowgraph technique and miscible phases in their studies. Craig, Geffen and Morse from the analysis of the performance of their laboratory model correlate many variables, including average saturation of a flooding agent determined by permeability relationship. Craig, et al, used X-ray shadowgraphs to determine the sweep efficiencies in sandstone models. In this report the sweep efficiency is not needed, and the important effect of continuously changing saturation gradients before and after breakthrough

By B. W. Frazer

In the numbers of the Engineering and Mining Journal of June 27th and July llth, 1874, there appeared some very complete statistics of the working of some anthracite blast-furnaces belonging to a large establishment in this country, followed by calculations of the heat requirements of the furnaces, similar to those which have been made for European furnaces by Mr. I. Lowthian Bell, Prof. Gruner, Prof. Akerman and others. To the author of these valuable papers, Mr. John A. Church, of New York, the thanks of American iron metallurgists are due for this attempt (the first, to my knowledge at least), to attack systematically and scientifically the problem of economy of fuel in our anthracite blast-furnaces, by applying the formulas obtained from European practice and from the experiments of European metallurgists, to the determination of the amounts and the modes of distribution of the heat production and absorption in our furnaces. In order to facilitate a comparison of the results thus obtained for the anthracite furnaces in question with those obtained for the best types of European coke furnaces, I have reduced 60 the same standad of heat units (the product of the ton and the degree Centigrade), and placed side by side, the calculations of the heat requirements of one of the furnaces of the Clarence works, as given by Mr. Bell, of a furnace at Pouzin, on the banks of the Rhone, given by Prof. Gruner, and of the anthracite furnaces for 1869-73, as given by Mr. Church. Table I shows the different conditions of working of the three furnaces, of which Table II gives the respective heat requirements. I have made this latter table in such a manner as to give for each furnace its heat requirements, both according to the views of Mr. Bell and those of Prof. Gruner. Mr. Bell assumes that all the carbonic acid produced by the decomposition of the carbonate of lime of the charge, is reduced to carbonic oxide by contact with solid carbon ; also, that the carbon of t,he pig iron is a portion of that deposited in the ore in the upper part of the furnace, by the dissociation of carbonic oxide. Prof. Gruner, on the other hand, assumes that all the carbonic acid of the carbonates of the charge escapes unreduced, and that the carbon deposited in the upper part. of the furnace, by the dissociation of carbonic oxide, is again converted into carbonic oxide or

By Hans Strack

Electroluminescence of GaAs p-n junctions fabricated by simultaneous diffusion of sulfur and iron was investigated at 77°K. A narrow emission peak with a half width of about 4 kT in the energy range between 1.14 and 1.155 eu was attributed to iron. Other transition elements exhibited light emission in the vicinity of the iron peak, namely nickel between 1.15 and 1.16 ev and cobalt between 1.16 and 1.17 ev. The efficiency of the doping with iron depended on the amoz~nt of arsenic present. A weight ratio of arsenic to iron of 4:l was sufficient to observe the emission lines associated with transition elements. The presence of oxygen reduces the intensity of the light emission. In addition to the levels associated with transition elements, levels at 1.05 and 1.28 ev, probably due to lattice defects, are observed except in diodes fabricated in solution-grown GaAs. THE near band edge emission of GaAsp-n junctions has been studied extensively in the past.' GaAs devices utilizing spontaneous and stimulated near band edge emission are of considerable practical importance. Typical junctions are fabricated by diffusion of a heavily doped p region into degenerate n-type GaAs. Much less work has been done on investigating the radiative recombination via deep levels in lightly doped p-type material. This area is of interest in understanding the performance of GaAs n-p-n transistors. GaAs transistors show remarkable improvement in high-frequency performance and current-gain stability at high temperatures, when iron is added to sulfur during the emitter diffusion process. The present work was initiated to investigate deep-level electroluminescence of iron-doped GaAs p-n junctions fabricated on vapor-phase epitaxial GaAs and on solution-grown GaAs. For comparison several diodes doped with cobalt and nickel were studied. Iron, cobalt, and nickel have an electron configuration of the type

Jan 1, 1968

By B. M. Larsen

IN spite of the great amount of operating experience and of studies directed toward elucidation of the interrelation of the several processes going on in the blast furnace, the present picture of its operation is based largely on indirect evidence and on speculation. The reason for this unsatisfactory situation is the extreme difficulty of making direct observations and significant measurements while the furnace is operating, and of translating laboratory experience to the conditions obtaining in the smelting process. Yet there are questions that can be investigated with some promise of a definitive answer; and it is the purpose of the present paper to set forth some of these questions, as a basis for discussion, which may, it is hoped, lead to active work on some of them. In order to provide a starting point for this discussion, some views held tentatively by the writer are outlined, along with a certain amount of evidence gathered from operating records and interpreted on the basis of the ideas expressed. These opinions may prove not to be pertinent, and may well not be in accord with the opinions of others; they have been included to encourage others to do likewise and on purpose to provoke informal discussion. In this way it should be possible to transcend the limitations of formal papers; to bring forth suggestions of new hypotheses or new methods of investigation; and to promote better understanding between investigators and operators in this difficult field. The statements made express the present views of one physical chemist who is not too familiar with all the difficulties of maintaining these enormous reaction vessels in reasonably smooth and economical operation; who, however, is persuaded that some of these difficulties would be less formidable if surer knowledge of the several interrelated and concurrent processes were available and made use of. For these difficulties arise largely, it is believed, from variation in conditions which the operator must meet as best be can, and should lessen as these conditions can be brought under control so that they are either made substantially constant or the variations are neutralized by compensating methods. A. VARIATION IN BURDEN AND IN MIXING OF CHARGE To the scientific investigator, who aims to control the conditions of experiment and to limit the number of variable factors, the most perplexing aspect of the blast-furnace process is that nothing seems to remain constant for long. Variations of burden seem to be unnecessarily frequent; and, even if the charge were constant from hour to hour, its constituents usually are not mixed as intimately as they might well be. It is understandable that separate layers of coke and of ore, also separate layers according to size, promote permeability and the

Jan 1, 1947

By Frederick Laist

While remodeling No. 1 section of the concentrator at the Washoe Reduction Works of the Anaconda Copper Mining Co. during the summer of 1912, for the purpose of ascertaining what additional metal recoveries could be made by improvements in concentration practice which had been developed by the staff of the Boston & Montana Reduction Department, at Great Falls, it was deemed advisable to carry on some experiments on the treatment of the regular mill tailings by roasting and leaching, to see whether the losses of metal values might not be still further decreased. In the course of these experiments about 5,000 tons of tailings were roasted, and of the resulting calcine about 200 tons were leached. The results were so satisfactory that it was decided to continue the work on a larger scale, particularly as regards the leaching end of the process, and construction work on an 80-ton roasting and leaching plant was accordingly commenced during the latter part of February, 1913, and is being pushed as rapidly as possible. 80-Ton Leaching Plant. This plant will consist of one 20-ft. roasting furnace of the Mac-Dougall type, specially adapted to the work of roasting for leaching; two leaching tanks, 32 ft. in diameter by 12 ft. deep, together with the necessary solution tanks, air lifts, precipitating launders, etc. It has been decided to precipitate the copper from solution on scrap iron, so as not to hamper the roasting and leaching departments by any weakness that might develop in the precipitating department. It is, however, the intention to experiment with a number of different methods of precipitation; for example, by electrolysis and by hydrogen sulphide. The acid required for the operation of this plant will be purchased, ad the quantity required is not sufficient to justify the installation of an acid plant. An acid plant will, however, be established in con-

Jan 1, 1914

By James F. Howe

EveRy engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of considerable money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate-sized rope, about 1 1/4in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire-rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be compared with the service of previous years with any fairness to the wire-

Jan 1, 1923

By C. F. Knutson, Martin Felsenthal, J. D. Lung, J. D. Sudbury

This paper has been written to summarize the laboratory and field studies leading to injection of Pacific Ocean water into the Third Grubb formation. Laboratory tests for studying the permeabilities of cores to Pacific Ocean water are described. Resu1ts of these tests showed that the water could be successfully injected if it is chertzically stable, sterile, and properly filtered. Clay swelling was shown to be a comparatively minor factor in permeability reduction. Studies leading to development of an economical system for properly conditioning the ocean water are discussed. It was necessary to control pH, calcium carbonate deposition, bacterial growth, iron solubility. oxygen, and suspended .solids. A relatively simple system combining the use of sulifur dioxide, a quaternary rlmmonium chloride, and filtration was shown to adeqrrately control all these factors. This combination has not previozrsly been used as a water treating technique. Evaluation tests of the water conditioning system prior to injection are described, and results of such tests are presented. Control measures needed to insure a continusously adequate water treatment are reviewed. INTRODUCTION The utilization of sea water for waterflooding has only recently been attempted. Knowledge of treating requirements has been limited, and in most cases no water treating has been done. Prior to the initiation of the Third Grubb zone pilot water flood at Ventura, Calif.,1,2 extensive laboratory research was done in an effort to define the treatment necessary to provide a suitable injection fluid. Close coordination and cooperation between field and research personnel were found to be the foremost requisites in developing the most economical and practical method for treating ocean water. LABORATORY STUDIES Plugging Tendencies of Untreated Ocean Water A program of laboratory studies was initiated for the purpose of evaluating whether ocean water could be injected into the formation for prolonged periods of time without causing plugging of the pore spaces of the formation. Because of the fairly low permeability of the formation (averaging about 40 md), it was realized from the outset that a water of exceptionally high quality was needed. Ocean water used in the laboratory studies was carefully filtered through ultrafine fritted glass filters, having nominal maximum pore sizes of 1.4 microns. Permeability tests were then performed on representative core material from the formation. It soon became apparent in these tests that filtration alone was not a sufficient treatment for the ocean water. Prolonged injection of the filtered water caused rapid plugging of the core samples. The permeability decline of a typical sample is illustrated by Curve A in Fig. 1. The several factors which can contribute to this plugging tendency are briefly reviewed below: Interaction with Formation Clays An evaluation of clay swelling effects on liquid permeability was made using core samples from the Grubb formation. An oil was chosen for determining the reference liquid permeability because it would not tend to react with any clays that might be present in the formation. The samples were then extracted, dried, and resat-urated with either treated ocean water, formation water, or fresh water. Permeabilities to the various waters were then determined. Results of this test series are summarized in Fig. 7. The difference between the oil permeability and water

Jan 1, 1957

By E. W. McAllister

THE decision of the California Oil Umpire's1 office to accept well potentials established from subsurface-pressure data has brought to the attention of many operators for the first time the application of such data to production problems. This paper reviews the development and application of subsurface-pressure data in Kettleman Hills, where these data have been used in production work since 1932. The Kettleman Hills field was discovered in October 1928. The first subsurface-pressure surveys were made early in 1932 and by the middle of 1933 the two major operators in the field were making routine pressure runs in their respective wells. Shortly thereafter, these companies agreed to exchange pressure data, and later a third company entered into the agreement. This made it possible to analyze the effects upon the reservoir pressure of past production practices, which are discussed in the latter part of the report. It is interesting that many of the applications of subsurface-pressure data discussed herein were anticipated by C. L. Clarks and C. B. Kimberlin‡ in a reports dated March 1933. PRODUCTIVITY INDEX In the majority of individual well problems involving the use of subsurface pressure data, it is necessary to use a factor known as the "productivity index," which indicates the ability of a well to produce and represents the number of barrels of oil or oil and water per day that will enter the well bore for each pound per square inch pressure drop made opposite the producing interval of the well. The productivity index may be determined from pressure and production data for one or more rates of flow and a static or shut-in pressure survey or from production and pressure data for two or more rates of flow. Productivity indices may be based upon either net oil or total fluid production. All indices referred to in this report are based upon net oil. The value of the productivity index for Kettleman Hills wells decreases generally with time and it is not uncommon for the index to vary in value at any specific time for various rates of flow. The decline of the productivity index may be attributed partly to the loss of reservoir pressure. As. the reservoir pressure decreases, gas originally in solution is released from the oil, congesting the flow of fluids through the formation and increasing the viscosity and surface tension of the oil; thus the flow resistance of the fluids through the formation is increased, resulting in a decrease of the productivity index. For convenient reference, the productivity indices for each well are plotted against time and a curve is drawn through the points showing the trend of the average index value. Plotted on Fig. I are index values for five

Jan 1, 1941

By Joseph E. Pogue

The past year in the petroleum industry was one of overproduction, rising inventories, low prices, and meagre to vanishing profits. This outcome was the result of a long period of intensive and uncompensated effort on the part of both financial and industrial interests, to stimulate supply on the theory that the primary problem facing the petroleum industry was the development of an adequate reserve of raw material to protect a large and ever-growing investment. The stimulus was applied in various forms and through diverse channels: capital had long flowed into the industry in excessive amounts under the attraction of large expected profits; the price level for crude petroleum had persistently been influenced by speculative considerations, with the result that prices declined slowly in periods of flush production and were quick to advance in anticipation of statistical improvement, thus maintaining a superfluous degree of stimulus on wildcatting and on drilling; speculation in inventories had led to the unsound, or at least unusual, business practice of accumulating huge stocks of oil; and, above all, the industry had directed the potent force of technology to the expansion of supply and achieved radical results in accelerating oil discovery, speeding up the rate of oil extraction, and enlarging the recovery of gasoline and lubricating oils from the raw material. In short, the economic conditions of 1927 were exactly those to which the objectively driven enterprise of the petroleum industry had long been directed; and the undesirable financial consequences arising therefrom reflected no lack of success in what had been set out to be achieved, but rather the failure to have established concurrently the necessary means of economic control to prevent the immediate conversion of reserves into current supply, and likewise the oversight in neglecting to apply the technological force to the enlargement and diversification of the market for petroleum products. Perhaps, when viewed in its longer perspective, 1927 will stand out as the turning point in the economic policy of the petroleum industry, when the technique of rationalizing production made its initial claim for recognition.

Jan 1, 1928

By T. A. Klinefelter

Lightweight concrete aggregates are materials weighing less than the usual aggregates of sand, gravel, and crushed rock. Concretes made with sand and gravel or crushed rock weigh 145 to 150 lb per cu ft, compared with 50 to 90 lb per cu ft for concretes made with lightweight aggregate. The ultra-lightweight concretes weigh much less than 50 lb per cu ft. Lightweight aggregates may be natural or manufactured materials, or byproducts from other commercial operations. Natural materials include pumice and pumicite, tuffs, breccia, scoria, diatomite, and vegetable products, such as peat, straw, and sawdust. Manufactured materials include expanded perlite, vermiculite, slag, clay, shale, and slate. Byproducts include cinders, aircooled slags, and coke breeze. Concretes made with lightweight aggregate were used first in construction of commercial buildings, later in homes. Present usage is general in multistory and other building construction, such as bridge decks, barges, jet-plane runways, piers and other structures. The industry has grown remarkably in the last decade. General Considerations The particular use to which the concrete may be put determines the importance of the various properties of the aggregates employed. Any given type of aggregate, however, should be reasonably uniform in composition and properties. It should be suitably graded and maintain proper weights, insulation values, and adequate strength to prevent breakdowns in mixing. It should bond properly with the cement, be inert to chemical reactions with cement and steel, and resist weathering, moisture, insects, and fungi. Some properties of any given type of lightweight aggregate from different suppliers may vary considerably because of differences in the source of raw material and the method of treatment. This statement applies particularly to expanded clays, shales and slates. All lightweight concretes have higher absorption of moisture and lower thermal conductivity, lower compressive strength, as well as lower unit weight as compared with standard concretes made with sand, gravel or crushed rock. Excepting cinders, the cost of lightweight aggregates is usually higher. Grading and unit weight requirements are given in ASTM standards: C 330-53T, Lightweight Aggregates for Structural Concrete; C 331-53T, Lightweight Aggregates for Concrete Masonry Units; C 332-54T, Lightweight Aggregates for Insulating Concrete. The production of masonry units shows the growth of the use and types of lightweight aggregates. In 1947 the total number of lightweight block was 460,000,000 units in 8 by 8 by 16-in. equivalents. By 1954 this had increased to 950,000,000 units. Of the 1954 production, 27 pct was of manufactured types, 43 pct of cinders, and 30 pct of remaining types. Raw Materials Used as Lightweight Aggregates It was stated above that a variety of products both natural and manufactured are used as lightweight aggregates. It is easy to understand that a bulky material of low unit value cannot be transported far and still remain a low cost product. Hence the product used in a particular market depends upon the availability of the possible raw materials. Thus it is

Jan 1, 1960

By S. S. Raymond, C. R. Hayward

In reheating quenched steel to remove part of the hardness, the softening effect has generally been considered to be a function of temperature and time. The temperature effect is well known, and long before pyrometers were heard of the blacksmith was able to do a good job of tempering, by rule-of-thumb methods and experience in judging temperatures. Modern conditions, which demand steel that will withstand the severest tests, require that the heat treatment be carried out with every possible precaution to secure the best results obtainable. Pyrometers and heat-treatment furnaces of many types are on the market and improvements are continually being made so that it is now possible to regulate the temperature in heat treatment very accurately. There is still a question regarding the time that the steel should be subjected to treatment. It is customary with all operators to insure the desired temperature throughout the specimen and it is generally supposed that a longer treatment of a hardened steel produces a further softening but there are few published figures showing the exact effect of time of treatment at constant temperature. A search of the literature disclosed several brief statements that the tempering effect was a function of both time and temperature, but in no case were any figures given. The opinion is very generally held that the well-know tempering colors are accurate indicators of the degree of tempering. This is disputed by Brearley (The Heat Treatment of Tool Steel, page 102) who states: It has been said that the result would be the same in respect to both hardness and other properties whether the colors were obtained by a shorter heating at a higher temperature or a longer heating at a lower one. This, to say the least, is a very doubtful conclusion, and is certainly not borne out by mechanical tests on oil-hardened and tempered motor car steels which, after tempering for periods varying from 15 min. to 2 hr., show no very great bifferences. The present investigation had for its object the obtaining of some definite data regarding the effect of time, which might serve as a guide to those engaged in the heat treatment of steel. The Rhode Island Tool Co. cooperated by furnishing the steel and machining the test specimens.

Jan 1, 1917

By Daniel T. O’Brian

Mineral exploration activities are benefiting from new interpretive techniques which have become economically practical with computers. Government agencies, educational institutions, and industry have each contributed research and development efforts for improving the mathematical analysis and graphical display of exploration data, resulting in operational aids not foreseeable a decade ago. Progress has been worldwide and is expanding rapidly. Books 1-10 are supplementing the periodic literature, at least one abstracting service is now active, 11 and an association has recently been formed to encourage and publicize advances in this field. 12 With the diversity of applications, only partial coverage of the subject can be made at any single symposium. Four of the six papers in this section report on the current state-of-the-art in selected areas of interest: graphics, time-sharing, mathematics, and economic analysis. The remaining two papers are descriptions of advanced statistical techniques for gaining additional information during exploration, and illustrate methods which will become more commonly applied in the future. "Computer Graphics: A New Tool for Exploration and Mining" describes the use of a computer and accessory equipment as an information retrieval device, graphically merging and displaying pertinent information for visual inspection and interpretation. This is a rapid means of studying information which has been pre-stored in a form accessible to the computer. Time-sharing is a means of achieving a comparable rapid response when calculations are being performed. The paper, "Some Applications of Time-Sharing in Mining Geophysics," describes the experience of one company using a time-sharing facility for geophysical computations. Another paper on this subject, stressing mining applications, has recently been published. 13

Jan 1, 1969

By V. H. Wilhelm

The year 1941 in the California oil industry was marked by an increased market demand, drilling activity, and production of crude oil. Although seven new oil fields and two gas fields were discovered during the year, additions to reserves from these discoveries, as well as extensions and revaluations of previous discoveries, were approximately 100 million barrels, as against estimated withdrawals of 230,233,000 barrels. The year was remarkable for the very great increase in domestic demand for all products, which more than compensated for the loss in shipments to Japan, which averaged 60,041 bbl. Per day during 1940. Demand in terms of crude during 1941 was 648,967 bbl. per day as against 632,647 for the same period in 1940. This abnormal increase in demand is due to increased industrial activity, and especially increased railroad activity. Gasoline consumption for 1941 was 241,011 bbl. per day as against 217,744 in 1940. Demand for fuel oil increased from 259,806 bbl. per day in 1940 to 285,896 in 1941, and caused a withdrawal from stocks of more than 7,473,000 barrels. During 1941, total oil storage declined 9,153,000 bbl., but additions to storage of 1,754,000 bbl. of light oil and light oil products were offset by a withdrawal of 10,907,000 bbl. of heavier products. Production during the year is estimated at 230,233,000 bbl. as against 222,784,386 bbl. for 1940. TraNsportation For a short time, California was affected by lack of transportation due to the diversion of tankers. This shortage affected the movement of oil from the Sari Joaquin mated to the refineries, since a large percentage of this production is moved to the coast through pipe lines, and thence by tankers to Los Angeles and San Fran-,iSco, Return of the tanker fleet, which may be temporary, indicates that there is a possibility of ample supplies of petroleum products in the Pacific Northwest. Drilling Activity Contrary to general opinion, drilling activity increased in 1941 over the pre-vious Year, 942 wells being completed in 1941 as against 890 in 1940, an increase Of 6 per cent. This increase was due to the increased demands for fuel oil, and also to the decreased drilling costs, which made many former marginal locations economic. The main activity caused by increased demands for fuel oil was in the Mt. Poso, McKittrick, Midway and Santa Maria Valley oil fields. Dry-hole footage in 1941 was 655,354 ft. as against 583,537 ft. for 1940. Curtailment Voluntary curtailment succeeded in holding production considerably below demand, although it was above the state quota. During the year the top allotment

Jan 1, 1942

By W. A. Johnson, F. N. Rhines, W. A. Anderson

The rate of the high-temperature oxidation of pure copper has been measured repeatedly by numerous investigators. It appears to be generally agreed: (I) that at constant temperature, after the initial stages of oxidation have been passed and the scale has attained a substantial depth, the film thickness increases in proportion to the square root of the time of oxidation; and (2) that for any given period of oxidation the logarithm of the square of the film thickness is proportional to the reciprocal of the absolute temperature of oxidation.' These relationships are explained upon the basis that the rate of diffusion of copper to the external surface of the film is the controlling factor in establishing the rate of growth. Extensive studies have been devoted also to the mechanism and rates of the early stages of oxidation. There is thus available a reasonably well established theory of the oxidation of pure copper upon which to construct an explanation of the more complex oxidation of copper alloys. Few general principles have as yet emerged from the chaos of observations that have been reported in the field of the oxidation of alloys.2 It is evident, however, that the copper alloys may be divided into two main groups, whose oxidation characteristics are distinguish- able. The first group, composed of the alloys with the noble metals, forms substantially pure copper oxide scales; the alloying element is concentrated within the residual metal, and sometimes particles of almost pure noble metal are found in the scales completely surrounded by copper oxide. In the second group, composed of the alloys of copper with the baser metals, the alloying element appears as an oxide in the scale, often in greater concentration than in the alloy itself and sometimes to the exclusion of copper oxide. The oxide scales of the latter class have been found to be made up of one, two, and sometimes more distinguishable layers of which the innermost is often metallic in character, composed of particles of the oxide of the alloying element embedded in essentially pure copper and known as the subscale or zone of internal oxidation. The need for a thorough quantitative study of these modes of oxidation is evident. Since it is apparent that several mechanisms must be cooperating to produce the complex oxide scales found on copper alloys, the analysis of the process into its several simple operations should prove instructive. Fortunately, it is possible experimentally to produce internal oxidation in the absence of an external scale; this permits the isolation and intensive study of one of the steps in the oxidation process. In the present research the rates of internal oxidation of an extensive series of dilute solid solution alloys of copper have been measured and a theory has been developed to predict the observed

Jan 1, 1942